Simultaneous Improvement of Photovoltaic Performance and Stability by In Situ Formation of 2D Perovskite at (FAPbI3)0.88(CsPbBr3)0.12/CuSCN Interface

To solve the stability issues of perovskite solar cells (PSC), here a novel interface engineering strategy that a versatile ultrathin 2D perovskite (5‐AVA)₂PbI₄ (5‐AVA = 5‐ammoniumvaleric acid) passivation layer that is in situ incorporated at the interface between (FAPbI₃)_0.88(CsPbBr₃)_0.12 and the hole transporting CuSCN is reported. Surface analysis using X‐ray photoelectron spectroscopy confirms the formation of 2D perovskite. Hysteresis is reduced by the interfacial 2D layer, which could be ascribed to improvement of interfacial charge extraction efficiency, associated with suppression of recombination. Moreover, introduction of the interface passivating layer enhances the moisture stability and photostability as compared to the control perovskite film due to hydrophobic nature of 2D perovskite. The unencapsulated device retains 98% of the initial power conversion efficiency (PCE) after 63 d under moisture exposure of about 10% in the dark. A PCE of the control device is boosted from 13.72 to 16.75% as a consequence of enhanced open‐circuit voltage (V_oc) and fill factor along with slightly increased short‐circuit current density (J_sc), which results from reduced trap states of (FAPbI₃)_0.88(CsPbBr₃)_0.12 as evidenced by enhanced carrier lifetimes and charge extraction. The perovskite/hole transport material interface engineering gives insight into simultaneous improvements of PCE and device stability.     

Electric-field-induced spin switch of endohedral dodecahedrane heterodimers H@C<Subscript>20</Subscript>H<Subscript>n</Subscript>–C<Subscript>20</Subscript>H<Subscript>n</Subscript>@M (M= Cu,Ag and Au,n = 15, 18, and 19): a theoretical study

We designed nine endohedral dodecahedrane heterodimers H@C₂₀H_n-C₂₀H_n@M (M = Cu, Ag, and Au, n = 15, 18, and 19) that may act as single-molecule spin switches, and we predicted theoretically that the ground states of the dimmers shift from low-spin states (S = 0) to the high-spin states (S = 1) under an external electric field applied parallel or perpendicular to the molecular symmetry axes, consisting well with the analyses of Stark effect. Molecular orbitals analyses provide an intuitive insight into the spin crossover behavior. This study expands the application of endohedral chemistry and provides new molecules for designing single-molecule spin switch.     

One-Step Preparation and Fluorescence Enhancement Effect in SiO2/Eu2+ Doped with Ag Nanowires

Eu²⁺ single-doped SiO₂ (SiO₂/Eu²⁺) and Eu²⁺, Ag nanowires co-doped SiO₂ (SiO₂/Eu²⁺–Ag) luminescent nanomaterials were prepared by an efficient one-step sol–gel method. Their microstructure and optical properties were characterized, and the fluorescence enhancement of Eu²⁺ by Ag nanowires was investigated. The experimental results indicate that the average diameter of Ag nanowires doped is 12.5 nm, and the length–diameter ratio is 30. The Ag nanowires cannot only enhance the light absorption of SiO₂/Eu²⁺ in the range of 230–350 nm, but also reduce the fluorescence lifetime of Eu²⁺. More importantly, the emission intensity is enhanced after doping Ag nanowires, and the red shift phenomenon of the emission spectrum is observed, red shift occurs between 10 and 56 nm. The highest fluorescence intensity is accessed under the Ag doping concentration of 0.10 %. Additionally, the emission of SiO₂/Eu²⁺ with 0.10 % of Ag doping at 456 nm is 16 times stronger than that of pure SiO₂/Eu²⁺. The present results indicate that the fluorescence enhancement is attributed to the local field enhancement and the increased radiative decay rates induced by Ag nanowires.     

Crossover of a high-spin (S=7/2, 3/2) to a low-spin (S=1/2) iron-selenium cluster in FA and FB of photosystem I on rebinding of PsaC onto P700-FX cores

 PsaC is a tightly bound ferredoxin in the Photosystem I (PS I) reaction center which contains two [4Fe-4S] clusters named F_A and F_B. We recently proposed that the mixed-ligand F_B cluster in C14D_PsaC and the mixed-ligand F_A cluster in C51D_PsaC exist in a spin state of S=3/2, and that a spin state crossover to S=1/2 occurs when the PsaC mutants are rebound onto P700-F_X cores. Since EPR signals from a highly rhombic S=3/2 spin state can be difficult to study, wild-type PsaC was reconstituted with iron and selenium to introduce an easily detected S=7/2 spin state similar to that shown for Clostridial ferredoxin. When the unbound [4Fe-4Se] PsaC was chemically reduced, a sharp derivative resonance was found at g=5.171 attributed to the excited ±3/2 doublet from an S=7/2 spin multiplet. An additional peak was found at g=5.616 attributed to the superimposed ±1/2 and ±3/2 doublets from a highly rhombic S=3/2 spin multiplet, and an axial set of resonances found around g=2.0 attributed, in part, to a classical S=1/2 spin state. When the [4Fe-4Se] PsaC was rebound onto P700-F_X cores, the spin population derived from the S=7/2 and 3/2 spin states was negligible. Illumination of the rebuilt PS I complex at 15 K resulted in two rhombic sets of resonances, one with g values of 2.043, 1.941 and 1.854, diagnostic of F_A, and the other with g values of 2.067, 1.941 and 1.878, diagnostic of F_B. Chemical reduction with sodium dithionite at pH 10.5 or photoaccumulation by freezing during illumination resulted in a set of resonances with g values of 2.046, 1.938, 1.920 and 1.883, characteristic of a spin-coupled F_A ^–/F_B ^– pair. The spin state crossover in this iron chalcogenide cluster is the first known to be induced by protein-protein association and reinforces the hypothesis that an S=3/2 to 1/2 crossover occurs in the PS I-rebound mutants C14D_PsaC and C51D_PsaC. Received: 6 August 1996 / Accepted: 28 December 1996     

Specific platinum chelation by the guanines of the deoxyhexanucleotide d(T-G-G-C-C-A) upon reaction with cis-[Pt(NH3)2(H2O)2](NO3)2

The stoichiometric reaction between d-TpGpGpCpCpA (d(T-G-G-C-C-A)) and $\text{cis}$-[Pt(NH₃)₂(H₂O)₂](NO₃)₂ (8.4 × 10^?6 to 1.3 × 10^?4M in water at pH 5.5–6) gives a single complex. High pressure gel permeation chromatography and pH-dependent ¹H NMR analyses of the nonexchangeable base protons, show that it is a platinum chelate with the $\text{cis}$-Pt^II(NH₃)₂ moiety bound to the two N7 atoms of the adjacent guanines. A 3 × 10^?3M reaction gives the same platinum chelate, via the formation of intermediate complexes, together with unsoluble adducts.     

High diving metabolism results in a short aerobic dive limit for Steller sea lions (Eumetopias jubatus)

The diving capacity of marine mammals is typically defined by the aerobic dive limit (ADL) which, in lieu of direct measurements, can be calculated (cADL) from total body oxygen stores (TBO) and diving metabolic rate (DMR). To estimate cADL, we measured blood oxygen stores, and combined this with diving oxygen consumption rates (VO₂) recorded from 4 trained Steller sea lions diving in the open ocean to depths of 10 or 40 m. We also examined the effect of diving exercise on O₂ stores by comparing blood O₂ stores of our diving animals to non-diving individuals at an aquarium. Mass-specific blood volume of the non-diving individuals was higher in the winter than in summer, but there was no overall difference in blood O₂ stores between the diving and non-diving groups. Estimated TBO (35.9 ml O₂ kg^?1) was slightly lower than previously reported for Steller sea lions and other Otariids. Calculated ADL was 3.0 min (based on an average DMR of 2.24 L O₂ min^?1) and was significantly shorter than the average 4.4 min dives our study animals performed when making single long dives—but was similar to the times recorded during diving bouts (a series of 4 dives followed by a recovery period on the surface), as well as the dive times of wild animals. Our study is the first to estimate cADL based on direct measures of VO₂ and blood oxygen stores for an Otariid and indicates they have a much shorter ADL than previously thought.     

The addition reactions of germylenoid H<Subscript>2</Subscript>GeAlCl<Subscript>3</Subscript> with ethylene: a theoretical investigation

Theoretical calculations using the M062X and QCISD methods were performed on the addition reactions of the aluminum germylenoid H₂GeAlCl₃ with ethylene. The most two stable structures of germylenoid H₂GeAlCl₃, i.e., the p-complex and three-membered ring structures, respectively, were employed as reactants. The calculated results indicate that, for the p-complex, H₂GeAlCl₃ there are two pathways, I and II, of which path I involves just one transition state, while path II involves two transition states between reactants and products. Comparing the reaction barrier heights of path I (44.6 kJ mol^?1) and II (37.6 kJ mol^?1), the two pathways are competitive, with similar barriers under the same conditions, while for the three-membered ring structure, another two pathways, III and IV, also exist. Path III has one transition state; however, in path IV, two transition states exist. By comparing their barrier heights, path III (barrier height 39.2 kJ mol^?1) could occur more easily than path IV (barrier height 92.8 kJ mol^?1). Considering solvent effects on these addition reactions, the PCM model and CH₂Cl₂ solvent were used in calculations, and the calculated results demonstrate that CH₂Cl₂ solvent is unfavorable for the reactions, except for path II. In CH₂Cl₂ solvent, paths II and III are more favorable than paths I and IV.     

Enhanced luminescence and white light emission from Eu3+‐co‐doped K3Ca2(SO4)3Cl:Dy3+ phosphor with near visible ultraviolet excitation for white LEDs

The luminescent properties of europium (Eu)‐ and dysprosium (Dy)‐co‐doped K₃Ca₂(SO₄)₃Cl halosulfate phosphors were analyzed. This paper reports the photoluminescence (PL) properties of K₃Ca₂(SO₄)₃Cl microphosphor doped with Eu and Dy and synthesized using a cost‐effective wet chemical method. The phosphors were characterized by X‐ray diffraction and scanning electron microscopy. The CIE coordinates were calculated to display the color of the phosphor. PL emission of the prepared samples show peaks at 484 nm (blue), 575 nm (yellow), 594 nm (orange) and 617 nm (red). The emission color of the Eu,Dy‐co‐doped K₃Ca₂(SO₄)₃Cl halophosphor depends on the doping concentration and excitation wavelength. The addition of Eu in K₃Ca₂(SO₄)₃Cl:Dy greatly enhances the intensity of the blue and yellow peaks, which corresponds to the ⁴ F_9/2 → ⁶H_15/2 and ⁴ F_9/2 → ⁶H_13/2 transitions of Dy³⁺ ions (under 351 nm excitation). The Eu³⁺/Dy³⁺ co‐doping also produces white light emission for 1 mol% of Eu³⁺, 1 mol% of Dy³⁺ in the K₃Ca₂(SO₄)₃Cl lattice under 396 nm excitation, for which the calculated chromaticity coordinates are (0.35, 0.31). Thus, K₃Ca₂(SO₄)₃Cl co‐doped with Eu/Dy is a suitable candidate for NUV based white light‐emitting phosphors technology. Copyright © 2014 John Wiley & Sons, Ltd.     

Target-oriented discovery of a new esterase-producing strain Enterobacter sp. ECU1107 for whole cell-catalyzed production of (2S,3R)-3-phenylglycidate as a chiral synthon of Taxol

A new strain, Enterobacter sp. ECU1107, was identified among over 200 soil isolates using a two-step screening strategy for the enantioselective synthesis of (2S,3R)-3-phenylglycidate methyl ester (PGM), a key intermediate for production of a potent anticancer drug Taxol^®. An organic–aqueous biphasic system was employed to reduce spontaneous hydrolysis of the substrate PGM and isooctane was found to be the most suitable organic solvent. The temperature and pH optima of the whole cell-mediated bioreaction were 40 °C and 6.0, respectively. Under these reaction conditions, the enantiomeric excess (ee _s) of (2S,3R)-PGM recovered was greater than 99 % at approximately 50 % conversion. The total substrate loading in batch reaction could reach 600 mM. By using whole cells of Enterobacter sp. ECU1107, (2S,3R)-PGM was successfully prepared in decagram scale in a 1.0-l mechanically stirred reactor, affording the chiral epoxy ester in >99 % ee _s and 43.5 % molar yield based on the initial load of racemic substrate.     

Sources of CO2 evasion from two subtropical rivers in North America

We directly measured the partial pressure of dissolved CO₂ (pCO₂) in two humid subtropical rivers in coastal Texas, one highly urbanized (Buffalo Bayou) and one relatively undeveloped (Spring Creek), and analyzed carbon isotopic signatures (Δ¹⁴C and δ ¹³C) of riverine dissolved inorganic carbon (DIC) to determine carbon sources sustaining river respiration. Both rivers were highly supersaturated with CO₂ at all study sites and on all dates sampled from June 2007 to February 2009. Mean riverine pCO₂ values are 3,052 ± 1,364 and 4,702 ± 1,980 μatm for Buffalo Bayou and Spring Creek, respectively. Calculated CO₂ emission fluxes per ha of water surface area from these rivers are intermediate between those in tropical and temperate rivers, indicating that globally, humid subtropical rivers may be a significant source of atmospheric CO₂. Carbon isotopic signatures revealed that CO₂ supersaturation is supported by different carbon sources for the two rivers. In the relatively undeveloped river (Spring Creek), young terrestrial organic matter (OM) is the predominant C source fueling river heterotrophic respiration. In the highly urbanized river (Buffalo Bayou), the high concentration of riverine CO₂ is additionally supported by dissolution of CaCO₃ likely from pedogenic carbonate, and crushed limestone/dolomite and oyster shells imbedded in old roads in the watershed. Because urban sources of acidity can include HNO₃ and H₂SO₄, whether the limestone/dolomite and shells used by humans act as a net sink or source of atmospheric CO₂ needs further study.     

Photoluminescence imaging of europium (III)‐doped γ‐Al2O3 nanofiber structures

Aluminium oxide (Al₂O₃) has widely been used for catalysts, insulators, and composite materials for diverse applications. Herein, we demonstrated if γ‐Al₂O₃ was useful as a luminescence support material for europium (Eu) (III) activator ion. The hydrothermal method and post‐thermal treatment at 800°C were employed to synthesize Eu(III)‐doped γ‐Al₂O₃ nanofibre structures. Luminescence characteristics of Eu(III) ions in Al₂O₃ matrix were fully understood by taking 2D and 3D‐photoluminescence imaging profiles. Various sharp emissions between 580 to 720 nm were assigned to the ⁵D₀→⁷F_J (J = 0, 1, 2, 3, 4) transitions of Eu(III) activators. On the basis of X‐ray diffraction crystallography, Auger elemental mapping and the asymmetry ratio, Eu(III) ions were found to be well doped into the γ‐Al₂O₃ matrix at a low (1 mol%) doping level. A broad emission at 460 nm was substantially increased upon higher (2 mol%) Eu(III) doping due to defect creation. The first 3D photoluminescence imaging profiles highlight detailed understanding of emission characteristics of Eu(III) ions in Al oxide‐based phosphor materials and their potential applications.     

Responses of high-elevation herbaceous plant assemblages to low glacial CO2 concentrations revealed by fossil marmot (Marmota) teeth

Atmospheric CO₂ cycles of the Quaternary likely imposed major constraints on the physiology and growth of C₃ plants worldwide. However, the measured record of this remains both geographically and taxonomically sparse. We present the first reconstruction of physiological responses in a late Quaternary high-elevation herbaceous plant community from the Southern Rocky Mountains, USA. We used a novel proxy—fossilized tooth enamel of yellow-bellied marmots (Marmota flaviventris)—which we developed using detailed isotopic analysis of modern individuals. Calculated C isotopic discrimination ( \(\Delta\) ) of alpine plants was nearly 2 ‰ lower prior to the Last Glacial Maximum than at present, a response almost identical to that of nonherbaceous taxa from lower elevations. However, initial shifts in \(\Delta\) aligned most closely with the onset of the late Pleistocene bipolar temperature “seesaw” rather than CO₂ increase, indicating unique limitations on glacial-age high-elevation plants may have existed due to both low temperatures and low CO₂. Further development of system-specific faunal proxies can help to clarify this and other plant- and ecosystem-level responses to past environmental change.     

Computational study of dynamic motions and possibility of crossing between surfaces in 3-hydroxy-5-(1H-pyrrol-2-yl)-2H-pyrrol-2-one

Potential energy surfaces (PESs) for tautomerism and two dynamic motions of 3-hydroxy-5-(1H-pyrrol-2-yl)-2H-pyrrol-2-one and its tautomer were calculated using density functional theory. Calculated energies confirm that T1 is 10.95 kJ mol^? 1 more stable than T2. Dynamic study of possible motions shows the high energy-level transition state at D8 = 90° for ring rotation and at D15 = 80° and 90° for rotation of OH bond, respectively, in T1 and T2. In addition, calculated rate constant for conversion of T1 to T2 (tautomerism) is 116 M^? 1 s^? 1, for relative rotations of rings in T1 and T2 are, respectively, 5.62 × 10^? 2 and 1.53 M^? 1 s^? 1 and for rotations of OH bond in T1 and T2 are, respectively, 3.56 × 10⁵ and 6.15 × 10⁴ M^? 1 s^? 1. In the next part of the study, orbital occupancies, natural bond orbitals (NBO) charges and hybridisation in relative rotation of rings and internal reaction coordinate (IRC) steps have been extracted to study the possibility of level crossing. These data show that PESs for IRC and ring rotation have different symmetries. So that these two potential curves cannot have effective non-adiabatic level crossing. However, the levels are weakly avoided or the possibility of level crossing is higher than related system because the energy difference between their barrier energies is not very high.     

Antibacterial combination therapy using Co3+, Cu2+, Zn2+ and Pd2+ complexes: Their calf thymus DNA binding studies

Four Co(III)-, Cu(II)-, Zn(II)-, and Pd(II)-based potent antibacterial complexes of formula K₃[Co(ox)₃].3H₂O (I), [Cu(bpy)₂Cl]Cl.5H₂O (II), [Zn(bpy)₃]Cl₂ (III), and [Pd(bpy)₂](NO₃)₂ (IV) (where ox is oxalate and bpy is 2,2′-bipyridine) were synthesized. They were characterized by elemental analyses, molar conductance measurements, UV–Vis, FTIR, ¹H NMR, and ¹³C NMR spectra. These metal complexes were ordered in three combination series of I + II, I + II + III, and I + II + III + IV. Antibacterial activity was tested for each of these four metal complexes and their combinations against Gram-positive and Gram-negative bacteria. All compounds were more potent antibacterial agents against the Gram-negative than those of the Gram-positive bacteria. The four metal complexes showed antibacterial activity in the order I > II > III > IV and the activity of their combinations followed the order of I + II + III + IV > I + II + III > I + II. CT-DNA binding studies of complex I and its three combinations were carried out using UV–vis spectral titration, displacement of ethidium bromide (EB), and electrophoretic mobility assay. The results obtained from UV–vis studies indicated that all series interact effectively with CT-DNA. Fluorescence titration revealed that the complexes quench DNA-EB strongly through the static quenching procedures. The binding constant (K_b), the Stern–Volmer constant (K_sv), and the number of binding sites (n) were determined at different temperatures of 293, 300, and 310 K, respectively. The calculated thermodynamic parameters supported that hydrogen binding and Van der Waals forces play a major role in association of each series of metal complexes with CT-DNA and follow the above-binding affinity order for the series.     

Conformational effect of a spin crossover iron(II) complex: Bis[N-(2-methylimidazol-4-yl)methylidene-2-aminoethyl]propanediamineiron(II) perchlorate

A iron(II) complex of the linear hexadentate N₆ ligand H₂L^2-3-2, [Fe(H₂L^2-3-2)](ClO₄)₂, was synthesized and the spin crossover properties were investigated, where H₂L^2-3-2 denotes bis[N-(2-methylimidazol-4-yl)methylidene-2-aminoethyl]propanediamine. The complex showed a gradual and reversible one-step spin crossover (SCO) between the high-spin (S = 2) and low-spin (S = 0) states at T_1/2 = 208 K without hysteresis. The crystal structures were determined at 296 and 250 K (HS state), 230, 210, and 200 K (intermediate between the HS and LS states) and 150 and 110 K (LS state). The spin transition from 296 to 150 K accompanies with the conformation change of the chelate rings at the triamine moiety and the formation of the hydrogen bond network in the same space group of orthorhombic Pbcn (no. 60). However, in the LS state at 110 K, the space group changed from orthorhombic Pbcn at 150 K (Pcan when the same axial setting to 110 K was used) to monoclinic P2₁/a (no. 14) at 110 K, although no spin transition and no change of assembly structure between 150 and 110 K were observed. It give us an idea that the space group transformation is mainly related to the conformational thermodynamic stability of the chelate rings at the triamine moiety and is not directly correlated with the spin transition.     

Enzymatic hydrolysis of nylons: quantification of the reaction rate of nylon hydrolase for thin-layered nylons

Nylon hydrolase degrades various aliphatic nylons, including nylon-6 and nylon-66. We synthesized a nylon-66 copolymer (M _w?=?22,900, M _n?=?7,400), in which a part of an adipoyl unit (32 % molar ratio) of nylon-66 was replaced with a succinyl unit by interfacial polymerization. To quantify the reaction rate of the enzymatic hydrolysis of nylons at the surface of solid polymers, we prepared a thin layer of nylons on the bottom surface of each well in a polystyrene-based micro-assay plate. The thickness of the nylon layer was monitored by imaging analysis of the photographic data. More than 99 % of the copolymer with thicknesses of 260 nm (approximately 600 layers of polymer strands) were converted to water-soluble oligomers by nylon hydrolase (3 mg enzyme ml^?1) at 30 °C within 60 h. These results were further confirmed by TLC analysis of the reaction products and by assay of liberated amino groups in the soluble fractions. The degradation rate of the thin-layered nylon-6 was similarly analyzed. We demonstrate that this assay enables a quantitative evaluation of the reaction rate of hydrolysis at the interface between the solid and aqueous phases and a quantitative comparison of the degradability for various polyamides.     

M2X (M= Li,Na; X= F,Cl): the smallest superalkali clusters with significant NLO responses and electride characteristics

Hypervalent M₂X (M = Li, Na; X = F, Cl) clusters are prototype species possessing lower ionisation potentials than Li, therefore classified as superalkalis. This study reveals some interesting properties of these small clusters using ab initio MP2/aug-cc-pVTZ and QCISD/aug-cc-pVTZ methods. These clusters are shown as an ionic species, composed of positively charged cage of alkali metals (M₂⁺) and halogen anion (X^?). Therefore, the stability of M₂X is governed by both ionic and covalent interactions. We show that the excess valence electron of (M₂⁺) is pushed out by anionic X^?, which allows M₂X clusters to possess ‘electride’ characteristics. It is also due to this excess electron that M₂X clusters exhibit significant non-linear optical (NLO) properties. The dipole moment, mean polarisability and hyperpolarisability suggest their significant NLO responses, which are explained on the basis of electronic transitions in crucial excited states using TD-B3LYP/aug-cc-pVTZ method. The first static hyperpolarisabilities of Li₂F and Na₂F take the values of order of 10⁴ a.u. due to their lower transition energies. This study should provide new insights into the design of novel materials with significant NLO responses useful for electro-optical applications.     

Hydrogen and oxygen trapping at the H-cluster of [FeFe]-hydrogenase revealed by site-selective spectroscopy and QM/MM calculations

[FeFe]-hydrogenases are superior hydrogen conversion catalysts. They bind a cofactor (H-cluster) comprising a four-iron and a diiron unit with three carbon monoxide (CO) and two cyanide (CN^?) ligands. Hydrogen (H₂) and oxygen (O₂) binding at the H-cluster was studied in the C169A variant of [FeFe]-hydrogenase HYDA1, in comparison to the active oxidized (Hox) and CO-inhibited (Hox-CO) species in wildtype enzyme. ⁵⁷Fe labeling of the diiron site was achieved by in vitro maturation with a synthetic cofactor analogue. Site-selective X-ray absorption, emission, and nuclear inelastic/forward scattering methods and infrared spectroscopy were combined with quantum chemical calculations to determine the molecular and electronic structure and vibrational dynamics of detected cofactor species. Hox reveals an apical vacancy at Fe_d in a [4Fe4S-2Fe]^3 ? complex with the net spin on Fe_d whereas Hox-CO shows an apical CN^? at Fe_d in a [4Fe4S-2Fe(CO)]^3 ? complex with net spin sharing among Fe_p and Fe_d (proximal or distal iron ions in [2Fe]). At ambient O₂ pressure, a novel H-cluster species (Hox-O₂) accumulated in C169A, assigned to a [4Fe4S-2Fe(O₂)]^3 ? complex with an apical superoxide (O₂^?) carrying the net spin bound at Fe_d. H₂ exposure populated the two-electron reduced Hhyd species in C169A, assigned as a [(H)4Fe4S-2Fe(H)]^3 ? complex with the net spin on the reduced cubane, an apical hydride at Fe_d, and a proton at a cysteine ligand. Hox-O₂ and Hhyd are stabilized by impaired O₂^– protonation or proton release after H₂ cleavage due to interruption of the proton path towards and out of the active site.     

PVP Treatment Induced Gradient Oxygen Doping in In2S3 Nanosheet to Boost Solar Water Oxidation of WO3 Nanoarray Photoanode

The photoelectrochemical performance of the WO₃ photoanode is limited by the severe charge recombination in the bulk phase and at the WO₃/electrolyte interface. Herein, In₂S₃ nanosheets are integrated onto the surface of the WO₃ nanowall array photoanode, followed by a facile polyvinylpyrrolidone (PVP) solution treatment. The PVP treatment results in sulfur vacancies and a gradient oxygen doping into In₂S₃ from surface to interior, which induces the formation of a gradient energy band distribution. The gradient band structured In₂S₃ and type II band alignment at the WO₃/In₂S₃ interface simultaneously create a channel that favors photogenerated electrons to migrate from the surface to the conductive substrate, thereby suppressing bulk carrier recombination. Meanwhile, the sulfur vacancies and oxygen doping contribute to increased charge carrier concentration, prolonged carrier lifetime, more active sites, and small interfacial transfer impedance. As a consequence, the PVP treated WO₃/In₂S₃ heterostructure photoanode exhibits a significantly enhanced photocurrent of 1.61 mA cm^?2 at 1.23 V versus reversible hydrogen electrode (RHE) and negative onset potential of 0.02 V versus RHE.