Effects of oxygen volumetric mass transfer coefficient and pH on lipase production by Staphylococcus warneri EX17

The principal objectives of this study were to evaluate the kinetics of lipase production by Staphylococcus warneri EX17 under different oxygen volumetric mass transfer coefficients (k_La) and pH conditions in submerged bioreactors, using glycerol (a biodiesel by-product) as a carbon source. Cultivations were conducted at different k_La (26, 38, 50, and 83 h⁻¹) and pH values (6.0, 7.0, and 8.0). The optimal k_La and pH were 38 h⁻¹ and 7.0, respectively. Under these conditions, the maximal cell production obtained was 8.0 g/L, and the volumetric and specific lipase production reached high levels of activity, approximately 800 U/L and 150 U/g cell, respectively, after 12 h of cultivation. This result was approximately five times higher than that obtained in the shake flask cultures. The relationship between cell growth and lipase production was found to be associated with growth by the Luedeking-Piret model.     

Microcalorimetric investigations of the metabolism of yeasts. growth in batch and chemostat cultures on ethanol medium

Summary In the presence of protein, Hansenula polymorpha cultivation medium exhibits a maximum volumetric mass transfer coefficient, k_La, as function of the employed antifoam agents (soy oil and Desmophen 3600). With diminishing superficial gas velocity this maximum disappeas.Symbols E_G Relative gas holdup - k_La Volumetric mass transfer coefficient (s^–1) - w_SL Superficial liquid velocity (cm s^–1) - w_SG Superficial gas velocity (cm s^–1)     

Enhanced oxygen transfer rates in fermentation using soybean oil-in-water dispersions

Summary The effect of soybean oil on the volumetric oxygen transfer coefficient during the cultivation ofAerobacter aerogenes cells is presented. For our aeration-agitation conditions (0.278 vvm and 500 rpm), it has been demonstrated that the use 19% (v/v) of soybean oil enabled a 1.85-fold increase of thek _l a coefficient (calculated on a per liter aqueous phase basis). For smaller volumetric oil fractions,k _L a increased linearly with the oil loading. Because of the oxygen-vector properties of soybean oil, this oil is able to significantly increase thek _L a of a bioreactor.Nomenclature C^*, C saturation and actual dissolved oxygen concentrations respectively (g/m³) - K_La volumetric oxygen transfer coefficient (h^–1) - K_La_initial k _La measured before the oil addition (h^–1) - M_O2 molar mass of oxygen (dalton) - N oxygen transfer rate (g/m³. h) - P_O2. P_N2 partial pressures ofO ₂ andN ₂ in the gas (atm) - P_H2OT partial pressure of water in air at the temperatureT (atm) - P_T total pressure (atm) - Q₀ volumetric flow rate of outlet air before seeding (m³/h) - Sp spreading coefficient (dynes/cm) - T absolute temperature of outlet gas (K) - V_i volume of the liquidi in the fermentor (m³) - V_M molar volume at 273 K and 1 atm (m³/mole) - _ij interfacial tension betweeni andj componants (dynes/cm) - _v volumetric fraction of the oil (v/v) - G gas - O oil - W water - i inlet - o outlet     

Effects of oxygen volumetric mass transfer coefficient on transglutaminase production by Bacillus circulans BL32

The effects of oxygenation in cultures of Bacillus circulans BL32 on transglutaminase (TGase) production and cell sporulation were studied by varying the agitation speed and the volume of aeration. Kinetics of cultivations has been studied in batch systems using a 2 L bioreactor, and the efficiency of agitation and aeration was evaluated through the oxygen volumetric mass transfer coefficient (k_La). It was adopted a two-stage aeration rate control strategy: first stage to induce biomass formation, followed by a second stage, in which cell sporulation was stimulated. A correlation of TGase production, spores formation, and oxygen concentration was established. Under the best conditions (500 rpm; 2 vvm air flow, followed by no air supply during stationary phase; k_La of 33.7 h⁻¹), TGase production reached a volumetric production of 589 U/L after 50 h of cultivation and the enzyme yield was 906 U/g cells. These values are 61% higher than that obtained in shaker cultures and TGase productivity increased 82%, when k_La varied from 4.4 to 33.7 h⁻¹. The maximal cell concentration increased four times in relation to shaker cultures and the cultivation time for the highest TGase activity was reduced from 192 h to just 50 h. These results show the importance of bioprocess design for the production of microbial TGase, especially concerning the oxygen supply of cultures and the induction of cell sporulation.     

Production and partial characterization of biosurfactant produced by Streptomyces sp. R1

The present study focused on developing a wild-type actinomycete isolate as a model for a non-pathogenic filamentous producer of biosurfactants. A total of 33 actinomycetes isolates were screened and their extracellular biosurfactants production was evaluated using olive oil as the main substrate. Out of 33 isolates, 32 showed positive results in the oil spreading technique (OST). All isolates showed good emulsification activity (E₂₄) ranging from 84.1 to 95.8%. Based on OST and E₂₄ values, isolate R1 was selected for further investigation in biosurfactant production in an agitated submerged fermentation. Phenotypic and genotypic analyses tentatively identified isolate R1 as a member of the Streptomyces genus. A submerged cultivation of Streptomyces sp. R1 was carried out in a 3-L stirred-tank bioreactor. The influence of impeller tip speed on volumetric oxygen transfer coefficient (k _L a), growth, cell morphology and biosurfactant production was observed. It was found that the maximum biosurfactant production, indicated by the lowest surface tension measurement (40.5 ± 0.05 dynes/cm) was obtained at highest k _L a value (50.94 h⁻¹) regardless of agitation speed. The partially purified biosurfactant was obtained at a concentration of 7.19 g L⁻¹, characterized as a lipopeptide biosurfactant and was found to be stable over a wide range of temperature (20–121 °C), pH (2–12) and salinity [5–20% (w/v) of NaCl].

     

Effect of aeration and agitation on the protease production by S<Emphasis Type="Italic">taphylococcus aureus</Emphasis> mutant RC128 in a stirred tank bioreactor

The modified rotating simplex method has been successfully used to determine the best combination of agitation rate and aeration rate for maximum production of extracellular proteases by Staphylococcus aureus mutant RC128, in a stirred tank bioreactor operated in a discontinuous way. This mutant has shown altered exoprotein production, specially enhanced protease production. Maximum production of proteases (15.28 UP/ml), measured using azocasein as a substrate, was obtained at exponential growth phase when the bioreactor was operated at 300 rpm and at 2 vvm with a volumetric oxygen transfer coefficient (K _L a) of 175.75 h⁻¹. These conditions were found to be more suitable for protease production.     

Effects of hydrocarbon additions on gas-liquid mass transfer coefficients in biphasic bioreactors

The effects of aliphatic hydrocarbons (n-hexadecane andn-dodecane) on the volumetric oxygen mass transfer coefficient (k _L a) were studied in flat alveolar airlift reactor and continuous stirred tank reactors (CSTRs). In the flat alveolar airlift reactor, high aeration rates (>2 vvm) were required in order to obtain efficient organic-aqueous phase dispersion and reliablek _L a measurements. Addition of 1% (v/v)n-hexadecane orn-dodecane increased thek _l a 1.55-and 1.33-fold, respectively, compared to the control (superficial velocity: 25.8×10⁻³ m/s, sparger orifice diameter: 0.5 mm). Analysis of the gas-liquid interfacial areaa and the liquid film mass transfer coefficientk _L suggests that the observedk _L a increase was a function of the media's liquid film mass transfer. Addition of 1% (v/v)n-hexadecane orn-dodecane to analogous setups using CSTRs led to ak _L a increase by a factor of 1.68 and 1.36, respectively (superficial velocity: 2.1×10⁻³ m/s, stirring rate: 250 rpm). These results propose that low-concentration addition of oxygen-vectors to aerobic microbial cultures has additional benefit relative to incubation in purely aqueous media.     

A comparative evaluation of oxygen mass transfer and broth viscosity using Cephalosporin-C production as a case strategy

The production of Cephalosporin-C (CPC) a secondary metabolite, using a mold Acremonium chrysogenum was studied in a lab scale Internal loop air lift reactor. Cephalosporin-C production process is a highly aerobic fermentation process. Volumetric gas–liquid mass transfer coefficient (k_La) and viscosity (η) were evaluated, during the growth and production phases of the microbial physiology. An attempt has been made to correlate the broth viscosity, η and volumetric oxygen transfer coefficient, k_La during the Cephalosporin-C production in an air lift reactor. The impact of biomass concentration and mycelial morphology on broth viscosity has been also evaluated. The broth exhibits a typical non-Newtonian fermentation broth. Rheology parameters like consistency index and fluidity index are also studied.     

Correlation between mass transfer coefficient k<Subscript>L</Subscript>a and relevant operating parameters in cylindrical disposable shaken bioreactors on a bench-to-pilot scale

Background

Among disposable bioreactor systems, cylindrical orbitally shaken bioreactors show important advantages. They provide a well-defined hydrodynamic flow combined with excellent mixing and oxygen transfer for mammalian and plant cell cultivations. Since there is no known universal correlation between the volumetric mass transfer coefficient for oxygen k_La and relevant operating parameters in such bioreactor systems, the aim of this current study is to experimentally determine a universal k_La correlation.

Results

A Respiration Activity Monitoring System (RAMOS) was used to measure k_La values in cylindrical disposable shaken bioreactors and Buckingham’s π-Theorem was applied to define a dimensionless equation for k_La. In this way, a scale- and volume-independent k_La correlation was developed and validated in bioreactors with volumes from 2 L to 200 L. The final correlation was used to calculate cultivation parameters at different scales to allow a sufficient oxygen supply of tobacco BY-2 cell suspension cultures.

Conclusion

The resulting equation can be universally applied to calculate the mass transfer coefficient for any of seven relevant cultivation parameters such as the reactor diameter, the shaking frequency, the filling volume, the viscosity, the oxygen diffusion coefficient, the gravitational acceleration or the shaking diameter within an accuracy range of +/? 30%. To our knowledge, this is the first k_La correlation that has been defined and validated for the cited bioreactor system on a bench-to-pilot scale.

     

Effect of n-dodecane on Crypthecodinium cohnii fermentations and DHA production

The potential use of n-dodecane as an oxygen vector for enhancement of Crypthecodinium cohnii growth and docosahexaenoic acid (DHA) production was studied. The volumetric fraction of oxygen vector influenced the gas–liquid volumetric mass transfer coefficient k _L a positively. The k _L a increased almost linearly with the increase of volumetric fraction of n-dodecane up to 1%. The stirring rate showed a higher influence on the k _L a than the aeration rate. The effects of this hydrocarbon on C. cohnii growth and DHA production were then investigated. A control batch fermentation without n-dodecane addition (CF) and a batch fermentation where n-dodecane 1% (v/v) was added (DF) were carried out simultaneously under the same experimental conditions. It was found that, before 86.7 h of fermentation, the biomass concentration, the specific growth rate, the DHA, and total fatty acids (TFA) production were higher in the CF. After this fermentation time, the biomass concentration, the DHA and TFA production were higher in the DF. The highest DHA content of biomass (6.14%), DHA percentage of TFA (51%), and DHA production volumetric rate r _DHA (9.75 mg l⁻¹ h⁻¹) were obtained at the end of the fermentation with n-dodecane (135.2 h). The dissolved oxygen tension (DOT) was always higher in the DF, indicating a better oxygen transfer due to the oxygen vector presence. However, since the other C. cohnii unsaturated fatty acids percentages did not increase with the oxygen availability increase due to the n-dodecane presence, a desaturase oxygen-dependent mechanism involved in the C. cohnii DHA biosynthesis was not considered to explain the DHA production increase. A selective extraction through the n-dodecane was suggested.     

Studies on fluid dynamics of the flow field and gas transfer in orbitally shaken tubes

Orbitally shaken cylindrical bioreactors [OrbShake bioreactors (OSRs)] without an impeller or sparger are increasingly being used for the suspension cultivation of mammalian cells. Among small volume OSRs, 50‐mL tubes with a ventilated cap (OSR50), originally derived from standard laboratory centrifuge tubes with a conical bottom, have found many applications including high‐throughput screening for the optimization of cell cultivation conditions. To better understand the fluid dynamics and gas transfer rates at the liquid surface in OSR50, we established a three‐dimensional simulation model of the unsteady liquid forms (waves) in this vessel. The studies verified that the operating conditions have a large effect on the interfacial surface. The volumetric mass transfer coefficient (k_La) was determined experimentally and from simulations under various working conditions. We also determined the liquid‐phase mass transfer coefficient (k_L) and the specific interfacial area (a) under different conditions to demonstrate that the value of a affected the gas transfer rate more than did the value of k_L. High oxygen transfer rates, sufficient for supporting the high‐density culture of mammalian cells, were found. Finally, the average axial velocity of the liquid was identified to be an important parameter for maintaining cells in suspension. Overall these studies provide valuable insights into the preferable operating conditions for the OSR50, such as those needed for cell cultures requiring high oxygen levels. © 2016 American Institute of Chemical Engineers Biotechnol. Prog., 33:192–200, 2017     

On-line estimation of kLa by an analog computer

A new method was developed for estimating the volumetric oxygen transfer coefficient, k_La, in a fermentor. Various methods were investigated for the on-line estimation of k_La with an analog computer employing a steepest-descent calculation technique. The method by which k_La is estimated (by minimizing the error residue of the model) was found to be very applicable. A method for the simultaneous estimation of the volumetric oxygen transfer coefficient and respiration rate in biological systems is also presented.     

Mixing and oxygen transfer characteristics of a microplate bioreactor with surface-attached microposts

Bioprocess optimization for cell-based therapies is a resource heavy activity. To reduce the associated cost and time, process development may be carried out in small volume systems, with the caveat that such systems be predictive for process scale-up. The transport of oxygen from the gas phase into the culture medium, characterized using the volumetric mass transfer coefficient, k_La, has been identified as a critical parameter for predictive process scale-up. Here, we describe the development of a 96-well microplate with integrated Redbud Posts to provide mixing and enhanced k_La. Mixing in the microplate is characterized by observation of dyes and analyzed using the relative mixing index (RMI). The k_La is measured via dynamic gassing out method. Actuating Redbud Posts are shown to increase rate of planar homogeneity (2 min) verse diffusion alone (120 min) and increase oxygenation, with increasing stirrer speed (3500-9000 rpm) and decreasing fill volume (150-350 μL) leading to an increase in k_La (4-88 h⁻¹). Significant increase in Chinese Hamster Ovary growth in Redbud Labs vessel (580,000 cells mL^-1) versus the control (420,000 cells mL^-1); t(12.814) = 8.3678, p ≤ .001), and CD4⁺ Naïve cell growth in the microbioreactor indicates the potential for this technology in early stage bioprocess development and optimization.     

Decolourization of anaerobically digested and polyaluminium chloride treated distillery spentwash in a fungal stirred tank aerobic reactor

Decolourization of anaerobically digested and polyaluminium chloride treated distillery spentwash was studied in a fungal stirred tank aerobic reactor without dilution of wastewater. Aspergillus niger isolate IITB-V8 was used as the fungal inoculum. The main objectives of the study were to optimize the stirrer speed for achieving maximum decolourization and to determine the kinetic parameters. A mathematical model was developed to describe the batch culture kinetics. Volumetric oxygen transfer coefficient (k _L a) was obtained using dynamic method. The maximum specific growth rate and growth yield of fungus were determined using Logistic equation and using Luedeking–Piret equation. 150 rpm was found to be optimum stirrer speed for overall decolourization of 87%. At the optimum stirrer speed, volumetric oxygen transfer coefficient (k _L a) was 0.4957 min⁻¹ and the maximum specific growth rate of fungus was 0.224 h⁻¹. The values of yield coefficient (Y _x/s) and maintenance coefficient (m _s) were found to be 0.48 g cells (g substrate)⁻¹ and 0.015 g substrate (g cells)⁻¹ h⁻¹.     

CFD analysis of the turbulent flow in baffled shake flasks

In this work, computational fluid dynamics (CFD) technique is used to simulate the complicated unsteady-state turbulent flow field formed in baffled flask. The baffled flask shows advantages both in mass transfer capacity and in shear formation in comparison with unbaffled flasks. Detailed investigations of power consumption, mass transfer and shear rate are carried out in baffled flasks under shaking frequencies ranging from 100 rpm to 250 rpm, and filling volumes from 50 mL to 150 mL. The results show that the specific power input and specific interface area are both greatly influenced by shaking frequency and filling volume. For the positive effect of shaking frequency on both mass transfer coefficient (k_L) and specific interface area (a), the volumetric mass transfer coefficient (k_La) increases greatly with shaking frequency. Results also show that filling volume has no significant effect on k_L but negative effect on specific interface area. Shear force formed in baffled flask shows great dependent on shaking frequency, but it is insensitive to the filling volume. Based on these investigations, correlations linking these parameters are proposed. Finally, cultivations of filamentous fungus conducted in unbaffled and baffled flasks validated the simulating results.     

Bubble coalescence behaviour in biological media

Summary A twin bubble column was used to measure the k_La values for oxygen in model and cultivation media using the steady state method described previously (Adler et al. 1980). Desmophen and soy oil were used as antifoam agents together with model and/or cultivation media for Chaetomium cellulotyticum, Trichoderma reesei, Hansenula polymorpha, Saccharomyces cerevisiae and Escherichia coli. The bubble coalescence behavior is mainly influenced by antifoam agents and somewhat by protein and alcohol additives. In the range investigated (0.01 to 0.1%.), the k_La values are not influenced by the Desmophen concentration and only slighthly by the soy oil concentration (0.5 to 1.5%.). The coalescence behaviour was characterized by the ratio m_corr=(k_La)_corr/(k_La)_ref. A nutrient salt solution with Desmophen was used as a reference. The k_La measured in the investigated media were corrected by considering the differences in k_La's in the investigated and reference media. These m_corr values can directly be used for bubble columns close to the optimum aeration rate.Symbols a Specific gas/liquid interfacial area - c Concentration - k_L Mass transfer coefficient - k_La Volumetric mass transfer coefficient - W_SG Superficial gas velocity - E_G Relative gas hold-up     

Oxygen transfer in an airlift reactor with multiple net draft tubes

A pilot scale airlift reactor with multiple net draft tubes was developed to improve oxygen transfer in the reactor. The reactor was 0.29 m in diameter and 2 m height. A steadystate sulfite oxidation method was applied to determine an overall volumetric mass transfer coefficient. Oxygen transfer of the proposed airlift reactor can be 60–100% higher than that of bubble columns under the same operating conditions.List of Symbols C ^* mol·dm^–3 saturated concentration of dissolved oxygen - C _L mol·dm^–3 bulk concentration of dissolved oxygen - G mol/min nitrogen flow rate - k _L a hr^–1 the volumetric gas-liquid mass transfer coefficient - Mo ₂ g/mol molecular weight of oxygen - OTR g/min the oxygen transfer rate - U _g cm/s superficial air velocity - V _L dm³ volume of the liquid phase - _in oxygen mole ratio in the inlet gas - _out oxygen mole ratio in the outlet gas     

Oxygen transfer model in recombinant <Emphasis Type="Italic">Pichia pastoris</Emphasis> and its application in biomass estimation

An oxygen transfer model was established for Pichia pastoris growing on glycerol and methanol in a stirred tank bioreactor and expressing a recombinant human serum albumin (rHSA). This was based on pseudo-steady state mass balance, where the volumetric O₂ transfer coefficient, k _L a, was estimated as a function of power input per unit volume and aeration rate. Under pseudo-steady state, the O₂ transfer rate model matched the O₂ uptake rate obtained from a previous macrokinetic model. This procedure was also applied to estimate biomass concentration by using the on-line rolling identification approach.     

Scale translation from shaken to diffused bubble aerated systems for lycopene production by Blakeslea trispora under stimulated conditions

This study deals with the scale up of Blakeslea trispora culture from the successful surface-aerated shake flasks to dispersed-bubble aerated column reactor for lycopene production in the presence of lycopene cyclase inhibitor 2-methyl imidazole. Controlling the initial volumetric oxygen mass transfer coefficient (k_La) via airflow rate contributes to increasing cell mass and lycopene accumulation. Inhibitor effectiveness seems to decrease in conditions of high cell mass. Optimization of crude soybean oil (CSO), airflow rate, and 2-methyl imidazole was arranged according to central composite statistical design. The optimized levels of factors were 110.5 g/L, 2.3 vvm, and 29.5 mg/L, respectively. At this optimum setting, maximum lycopene yield (256 mg/L) was comparable or even higher to those reported in shake flasks and stirred tank reactor. 2-Methyl imidazole use at levels significantly lower than those reported for other inhibitors in the literature was successful in terms of process selectivity. CSO provides economic benefits to the process through its ability to stimulate lycopene synthesis, as an inexpensive carbon source and oxygen vector at the same time.