Immobilization of glucose oxidase with Bombyx mori silk fibroin by only stretching treatment and its application to glucose sensor

Glucose oxidase (GOD) was immobilized in Bombyx mori silk fibroin membrane by only physical treatment, i.e., stretching without any chemical reagents. This is due to the structural transition of the silk fibroin membrane from random coil to antiparallel beta-sheet (Silk II) induced by the stretching treatment. Permeability coefficients of glucose and oxygen through the fibroin membrane were determined; the permeability of glucose decreased with increasing degree of stretching. The immobilized enzyme activity was characterized with apparent Michaelis constant K(m) (app) and maximal activity V(m). Optimum pH of the activity of the immobilized enzyme was shifted to the value around neutrality, and the activity was maintained to the higher values on both sides of the optimum pH compared with the case of free enzymes. Thermal stability was scarcely lost even at 50 degrees C, although the free enzyme lost about 70% of the original activity. Thus, the stabilities of the enzyme vs. pH and heat were much improved by the immobilization with silk. Glucose sensor prepared with this GOD-immobilized fibroin membrane was developed; the capabilities such as the response time, calibration curve, and repeating usage were determined.     

Immobilization of glucose oxidase on Fe<Subscript>3</Subscript>O<Subscript>4</Subscript>/SiO<Subscript>2</Subscript> magnetic nanoparticles

Glucose oxidase (GOD) was covalently immobilized onto Fe₃O₄/SiO₂ magnetic nanoparticles (FSMNs) using glutaraldehyde (GA). Optimal immobilization was at pH 6 with 3-aminopropyltriethoxysilane at 2% (v/v), GA at 3% (v/v) and 0.143 g GOD per g carrier. The activity of immobilized GOD was 4,570 U/g at pH 7 and 50°C. The immobilized GOD retained 80% of its initial activity after 6 h at 45°C while free enzyme retained only 20% activity. The immobilized GOD maintained 60% of its initial activity after 6 cycles of repeated use and retained 75% of its initial activity after 1 month at 4°C whereas free enzymes retained 62% of its activity.     

Silica-encapsulated magnetic nanoparticles: enzyme immobilization and cytotoxic study

Silica-encapsulated magnetic nanoparticles (MNPs) were prepared via microemulsion method. The products were characterized by high resolution transmission electron microscopy (HRTEM) and energy-dispersive X-ray spectrum (EDS). MNPs with no observed cytotoxic activity against human lung carcinoma cell and brine shrimp lethality were used as suitable support for glucose oxidase (GOD) immobilization. Binding of GOD onto the support was confirmed by the FTIR spectra. The amount of immobilized GODs was 95 mg/g. Storage stability study showed that the immobilized GOD retained 98% of its initial activity after 45 days and 90% of the activity was also remained after 12 repeated uses. Considerable enhancements in thermal stabilities were observed for the immobilized GOD at elevated temperatures up to 80°C and the activity of immobilized enzyme was less sensitive to pH changes in solution.     

Stabilization of immobilized glucose oxidase against thermal inactivation by silanization for biosensor applications

An important requirement of immobilized enzyme based biosensors is the thermal stability of the enzyme. Studies were carried out to increase thermal stability of glucose oxidase (GOD) for biosensor applications. Immobilization of the enzyme was carried out using glass beads as support and the effect of silane concentration (in the range 1-10%) during the silanization step on the thermal stability of GOD has been investigated. Upon incubation at 70 degrees C for 3h, the activity retention with 1% silane was only 23%, which increased with silane concentration to reach a maximum up to 250% of the initial activity with 4% silane. Above this concentration the activity decreased. The increased stability of the enzyme in the presence of high silane concentrations may be attributed to the increase in the surface hydrophobicity of the support. The decrease in the enzyme stability for silane concentrations above 4% was apparently due to the uneven deposition of the silane layer on the glass bead support. Further work on thermal stability above 70 degrees C was carried out by using 4% silane and it was found that the enzyme was stable up to 75 degrees C with an increased activity of 180% after 3-h incubation. Although silanization has been used for the modification of the supports for immobilization of enzymes, the use of higher concentrations to stabilize immobilized enzymes is being reported for the first time.     

Enhancement of stability of immobilized glucose oxidase by modification of free thiols generated by reducing disulfide bonds and using additives

Stability of glucose oxidase (GOD) immobilized with lysozyme has been considerably enhanced by modification of free thiols generated by reducing disulfide bonds using beta-mercaptoethanol and N-ethylmaleimide in conjunction with additives like antibiotics and salts. Thermal stability of immobilized GOD was quantified by means of the transition temperature, Tm and the operational stability by half-life t1/2 at 70 degrees C. Modification of the free thiols in the enzyme coupled with the presence of kanamycin, NaCl, and K2SO4, led to increase in Tm, to 80, 82 and 84 degrees C (compared to 75 degrees C in control) and t1/2 by 7.7-, 11- and 22-fold, respectively, indicating that this method can be effectively used for enhancing the stability of enzymes.     

Stabilization of activity of oxidoreductases by their immobilization onto special functionalized glass and novel aminocellulose film using different coupling reagents

Glucose oxidase (GOD), horseradish peroxidase (HRP), and lactate oxidase (LOD) were covalently immobilized on special NH(2)-functionalized glass and on a novel NH(2)-cellulose film via 13 different coupling reagents. The properties of these immobilized enzymes, such as activity, storage stability, and thermostability, are strongly dependent on the coupling reagent. For example, GOD immobilized by cyanuric chloride on the NH(2)-cellulose film loses approximately half of its immobilized activity after 30 days of storage at 4 degrees C or after treatment at 65 degrees C for 30 min. In contrast, GOD immobilized by L-ascorbic acid onto the same NH(2)-cellulose film retains 90% of its initial activity after 1 year of storage at 4 degrees C and 92% after heat treatment at 65 degrees C for 30 min. Unlike GOD, in the case of LOD only immobilization on special NH(2)-functionalized glass, e.g., via cyanuric chloride, led to a stabilization of the enzyme activity in comparison to the native enzyme. The operational stability of immobilized HRP was up to 40 times higher than that of the native enzyme if coupling to the new NH(2)-cellulose film led to an amide or sulfonamide bond. Regarding the kinetics of the immobilized enzymes, the coupling reagent plays a minor role for the enzyme substrate affinity, which is characterized by the apparent Michaelis constant (K(M,app)). The NH(2)-functionalized support material as well as the immobilized density of the protein and/or immobilized activity has a strong influence on the K(M,app) value. In all cases, K(M,app) decreases with increasing immobilized enzyme protein density and particularly drastically for GOD.     

Inner epidermis of onion bulb scale: As natural support for immobilization of glucose oxidase and its application in dissolved oxygen based biosensor

Inner epidermal membrane of the onion bulb scales was studied as a natural polymer support for immobilization of the glucose oxidase (GOD) enzyme for biosensor application. Onion epidermal membrane was used for immobilization of glucose oxidase and was associated with dissolved oxygen (DO) probe for biosensor reading. Glucose was detected on the basis of depletion of oxygen, when immobilized GOD oxidizes glucose into gluconolactone. A wide detection range between 22.5 and 450 mg/dl was estimated from calibration plot. A single membrane was reused for 127 reactions with retention of approximately 90% of its initial enzyme activity. Membrane was stable for 45 days ( approximately 90% activity) when stored in buffer at 4 degrees C. Surface structure studies of the immobilized membranes were carried under SEM. To our knowledge, this is the first report on employing inner epidermal membrane of onion bulb scales as the solid support for immobilization of enzyme.     

Carboxypeptidase a immobilization on activated styrene-maleic anhydride systems

The copolymer styrene-maleic anhydride (SMA) was activated to various forms to create enzyme coupling groups. Carboxypeptidase A (CPA) was Immobilized on these supports to enhance their thermal and chemical stability. Immobilized enzyme retained 60-70% of the original activity. When kept at 60 degrees C, while free enzyme was deactivated within 30 min, the immobilized enzyme retained 40% of initial activity at the end of 3 h. The half-life of free enzyme was only 21 min, while for immobilized enzyme it was enhanced up to 3 h. Also, the immobilized enzyme could be repeatedly used over 50 times retaining almost 50% of original activity.     

Immobilization of biocatalysts with bombyx mori silk fibroin by several kinds of physical treatment and its application to glucose sensors

Biocatalyst-immobilized Bombyx mori silk fibroin membrane was prepared. The insolubilization of the water-soluble membranes was performed by physical treatments only, i.e. stretching, compressing and standing under high humidity and methanol-immersion treatment, without any use ofcovalently binding reagent. All physical treatments performed were effective for the purpose of the immobilization of the enzymes in the membranes. The structural characterization of the glucose oxidase (GOD) immobilized membrane was performed in detail. The permeability of the substrate depends on the crystalline structure, i.e. the fraction of Silk I and Silk II of the membrane. The activity yield of the immobilized GOD was more than 80% of the value of free enzyme when 0–002% of the enzyme was entrapped in the membrane, but it decreased with increasing the concentration of the GOD in the membrane. This seems to result from diffusion limitation of the substrate. The pH and thermal stabilities of the immobilized enzyme were much improved, and were essentially independent of the methods of the immobilization. Development of the GOD or microorganism, Pseudomonas fluorescens immobilized silk fibroin membranes as glucose sensors are described.     

A smart bioconjugate of chymotrypsin

alpha-Chymotrypsin was immobilized on Eudragit S-100 via covalent coupling with 93% retention of proteolytic activity. The conjugate behaved as a smart biocatalyst and functioned as a pH-dependent reversibly soluble-insoluble biocatalyst. The pH optimum of chymotrypsin broadened on immobilization, and the immobilized preparation showed better stability at and above pH 6.5 as compared to the free enzyme. The immobilized enzyme showed a slight shift in the temperature optimum and enhanced thermal stability retaining 70% of its original activity after 1 h of exposure to 40 degrees C as compared to the 25% residual activity for the free enzyme under identical conditions. K(m) and V(max) values did not change on immobilization. Also, the immobilized preparation was quite stable to reuse, it retained almost 85% of its original activity even after a fifth precipitation cycle. UV spectroscopy and circular dichroism were used to probe structural changes in the enzyme upon immobilization.     

Simultaneous and sequential co-immobilization of glucose oxidase and catalase onto florisil

The co-immobilization of Aspergillus niger glucose oxidase (GOD) with bovine liver catalase (CAT) onto florisil (magnesium silicate-based porous carrier) was investigated to improve the catalytic efficiency of GOD against H2O2 inactivation. The effect of the amount of bound CAT on the GOD activity was also studied for 12 different initial combinations of GOD and CAT, using simultaneous and sequential coupling. The sequentially co-immobilized GOD-CAT showed a higher efficiency than the simultaneously co-immobilized GOD-CAT in terms of the GOD activity and economic costs. The highest activity was shown by the sequentially co-immobilized GOD-CAT when the initial amounts of GOD and CAT were 10 mg and 5 mg per gram of carrier. The optimum pH, buffer concentration, and temperature for GOD activity for the same co-immobilized GOD-CAT sample were then determined as pH 6.5, 50 mM, and 30 degrees C, respectively. When compared with the individually immobilized GOD, the catalytic activity of the co-immobilized GOD-CAT was 70% higher, plus the reusability was more than two-fold. The storage stability of the co-immobilized GOD-CAT was also found to be higher than that of the free form at both 5 degrees C and 25 degrees C. The increased GOD activity and reusability resulting from the co-immobilization process may have been due to CAT protecting GOD from inactivation by H2O2 and supplying additional O2 to the reaction system.     

Glucose oxidase immobilized on eupergit C and CPG-10 a comparison

Summary Using a photometric test, two immobilization matrices Eupergit C and controlled pore glass CPG-10 have been investigated with regard to their binding capacity for glucose oxidase (GOD). The results of these investigations show that Eupergit C has a specific binding capacity three times higher than CPG-10. A long-run test was carried out with an ezyme thermistor to detect the immobilized enzyme activity of the Eupergit C preparation. After three weeks, enzyme activity had declined to 52% of original value, however no additional loss GOD activity was observed between three and six weeks.     

Immobilization of Amaranthus leaf oxalate oxidase on alkylamine glass

A membrane bound oxalate oxidase from leaves of Amaranthus spionsus has been partially purified and immobilized on alkylamine glass with a yield of 9.2 mg protein/g support. The enzyme retained 99.4% of initial activity of free enzyme after immobilization. There was no change in the optimum pH (3.5) and Vmax but the temperature for maximum activity was slightly decreased (35 degrees C) and energy of activation (Ea) and Km for oxalate were increased after immobilization. The immobilized enzyme preparation was stable for 6 months, when stored in distilled water at 4 degrees C. Presence of Cl- did not affect the activity of immobilized enzyme.     

Activity and storage stability of immobilized glucose oxidase onto magnesium silicate

Glucose oxidase (GOD) was covalently immobilized onto florisil (magnesium silicate) carrier via glutaraldehyde. Immobilization conditions were optimized: the amount of initial GOD per grams of carrier as 5 mg, pH as 5.5, immobilization time as 120 min and temperature as 10 °C. Under the optimized reaction conditions activities of free and immobilized GOD were measured. Free and immobilized GOD samples were characterized with their kinetic parameters, and thermal and storage stabilities. K_M and V_max values were 68.2 mM and 435 U mg GOD⁻¹ for free and 259 mM and 217 U mg GOD⁻¹ for immobilized enzymes, respectively. Operational stability of the immobilized enzyme was also determined by using a stirred batch type column reactor. Immobilized GOD was retained 40% of its initial activity after 50 reuses. Storage stabilities of the immobilized GOD samples stored in the mediums with different relative humidity in the range of 0–100% were investigated during 2 months. The highest storage stability was determined for the samples stored in the medium of 60% relative humidity. Increased relative humidity from 0% to 60% caused increased storage stability of immobilized GODs, however, further increase in relative humidity from 80% to 100% caused a significant decrease in storage stability of samples.     

Immobilization of d-glucose oxidase onto a hydrogen peroxide permselective membrane and application for an enzyme electrode

A hydrogen peroxide permselective membrane with asymmetric structure was prepared and d-glucose oxidase (EC 1.1.3.4) was immobilized onto the porous layer. The activity of the immobilized d-glucose oxidase membrane was 0.34 units cm^?2 and the activity yield was 6.8% of that of the native enzyme. Optimum pH, optimum temperature, pH stability and temperature stability were found to be pH 5.0, 30–40°C, pH 4.0–7.0 and below 55°C, respectively. The apparent Michaelis constant of the immobilized d-glucose oxidase membrane was 1.6 × 10^?3 mol l^?1 and that of free enzyme was 4.8 × 10^?2 mol l^?1. An enzyme electrode was constructed by combination of a hydrogen peroxide electrode with the immobilized d-glucose oxidase membrane. The enzyme electrode responded linearly to d-glucose over the concentration 0–1000 mg dl^?1 within 10 s. When the enzyme electrode was applied to the determination of d-glucose in human serum, within day precision (CV) was 1.29% for d-glucose concentration with a mean value of 106.8 mg dl^?1. The correlation coefficient between the enzyme electrode method and the conventional colorimetric method using a free enzyme was 0.984. The immobilized d-glucose oxidase membrane was sufficiently stable to perform 1000 assays (2 to 4 weeks operation) for the determination of d-glucose in human whole blood. The dried membrane retained 77% of its initial activity after storage at 4°C for 16 months.     

Covalent immobilization of glucose oxidase onto poly(styrene-co-glycidyl methacrylate) monodisperse fluorescent microspheres synthesized by dispersion polymerization

In this study, micron-sized poly(styrene-co-glycidyl methacrylate) (PSt-GMA) fluorescent microspheres of 5.1microm in diameter were synthesized via dispersion polymerization of styrene and glycidyl methacrylate in the presence of 1,4-bis(5-phenyloxazol-2-yl) benzene (POPOP), which provided surface functional groups for covalent immobilization of enzymes. In an effort to study the biocompatibility of the microspheres' surface, glucose oxidase and beta-d-(+)-glucose were selected as a catalytic system for enzymatic assays. A colorimetric method was adopted in evaluating enzymatic activity by introducing horseradish peroxidase (HRP). Both the immobilization amount and the apparent activity of immobilized glucose oxidase from Aspergillus niger (GOD) were determined at different conditions. The results show that the immobilized enzymes retained approximately 28 to 34% activity, as compared with free enzymes, without pronounced alteration of the optimum pH and temperature. Kinetics studies show that the corresponding values of K(m) and V(max) are 23.2944 mM and 21.6450M/min.mg GOD for free enzymes and 35.1780 mM and 15.4799M/min.mg GOD for immobilized enzymes. The operational stability studies show that immobilized GOD could retain nearly 50% initial activity after being washed 20 times. The results suggest that the resultant PSt-GMA fluorescent microspheres provide a suitable surface for covalent immobilizing biomolecules; therefore, they have the potential of being used in fluorescence-based immunoassays in high-throughput screening or biosensors.     

Immobilization of chitosan-invertase neoglycoconjugate on carboxymethylcellulose-modified chitin

Saccharomyces cerevisiae invertase, chemically modified with chitosan, was immobilized on a carboxymethylcellulose-coated chitin support via polyelectrolyte complex formation. The yield of immobilized protein was determined to be 72% and the enzyme retained 68% of the initial invertase activity. The optimum temperature for invertase was increased by 5 degrees C and its thermostability was enhanced by about 9 degrees C after immobilization. The immobilized enzyme was stable against incubation in high ionic strength solutions and was 12.6-fold more resistant to thermal treatment at 65 degrees C than the native counterpart. The prepared biocatalyst retained 98% and 100% of the original catalytic activity after 10 cycles of reuse and 70 h of continuous operational regime in a packed bed reactor, respectively. The immobilized enzyme retained 95% of its activity after 50 days of storage at 37 degrees C.     

Immobilization of Aspergillus oryzae tannase and properties of the immobilized enzyme

Tannase enzyme from Aspergillus oryzae was immobilized on various carriers by different methods. The immobilized enzyme on chitosan with a bifunctional agent (glutaraldehyde) had the highest activity. The catalytic properties and stability of the immobilized tannase were compared with the corresponding free enzyme. The bound enzyme retained 20·3% of the original specific activity exhibited by the free enzyme. The optimum pH of the immobilized enzyme was shifted to a more acidic range compared with the free enzyme. The optimum temperature of the reaction was determined to be 40 °C for the free enzyme and 55 °C for the immobilized form. The stability at low pH, as well as thermal stability, were significantly improved by the immobilization process. The immobilized enzyme exhibited mass transfer limitation as reflected by a higher apparent K_m value and a lower energy of activation. The immobilized enzyme retained about 85% of the initial catalytic activity, even after being used 17 times.     

Immobilization of glucose oxidase and lactate dehydrogenase onto magnetic nanoparticles for bioprocess monitoring system

Glucose oxidase (GOD) and lactate dehydrogenase (LDH) were immobilized onto magnetic nanoparticles, viz. Fe₃O₄, via carbodiimide and glutaraldehyde. The immobilization efficiency was largely dependent upon the immobilization time and concentration of glutaraldehyde. The magnetic nanoparticles had a mean diameter of 9.3 nm and were superparamagnetic. The immobilization of GOD and LDH on the nanoparticles slightly decreased their saturation magnetization. However, the FT-IR spectra showed that GOD and LDH were immobilized onto the nanoparticles by different binding mechanisms, the reason for which was not well explained. The optimum pH values of the immobilized GOD and LDH were changed to 8 and 10, respectively. The free and immobilized enzyme kinetic parameters (K_m and V_max) were determined by Michaelis-Menten enzyme kinetics. The Km values for free and immobilized GOD were 0.168 and 0.324 mM, respectively, while those for free and immobilized LDH were 0.19 and 0.163 mM for NAD, and 2.976 and 4.785 mM for lactate, respectively. High operational stability was observed, with more than 80% of the initial enzyme activity being retained for the immobilized GOD up to 12 h and for the immobilized LDH up to 24 h. The immobilized GOD was applied to a sequential injection analysis system for the application of bioprocess monitoring.     

Immobilization of urease on vermiculite

Urease (EC 3.5.1.5) of high activity was obtained when the enzyme was immobilized on vermiculite crosslinked with 2.5% glutaraldehyde in chilled EDTA-phosphate buffer (pH 5.5). The highest activity of the immobilized enzyme was at 65°C and pH 6.5 while the optimum temperature for free urease was found to be 25°C. The thermal stability of immobilized urease was observed to be much better than that of the free urease. When stored at 4°C, urease immobilized on vermiculite retained 69 to 81% of its activity after 60 days and 61 to 75% of its original activity was retained after 4 repeated uses.