Influence of substrate wood-chip particle size on shiitake (Lentinula edodes) yield

Wood chips from four commercial hardwood sawmills were screened with 10 US standard sieves (4-0.21 mm) to assess particle size distributions. 96-98% of wood chips were < 4 mm while 95-99% of particles were > 0.21 mm. The majority (mean = 64.5%) of wood chips passed through US standard sieve size 14 (< 1.4 mm). Shiitake (Lentinula edodes) was grown in three crops to determine the effect of four particle size classes (1 = 2.8-4 mm; 2 = 1.7-2.8 mm; 3 = 0.85-1.7 mm; 4 = < 0.85 mm) on mushroom yield. Yields from substrates prepared with wood chips from class 4 (< 0.85 mm) were lower by 27.7%, 12.4% and 2% (mean = 14.9%) for Crops I, II, and III, respectively, when compared to controls. Profiling of wood chips may help growers optimize their production media and reduce production costs.     

An improved method for evaluating hardwood animal bedding products

Technological improvements have led to the development of higher quality hardwood bedding products with lower dust content. Nevertheless, testing procedures used to evaluate the quality of laboratory animal bedding products have not kept pace, resulting in the continued use of flawed and outdated test methods. The present study was conducted to develop an improved method for evaluating the quality of hardwood animal bedding products.     

The influence of mesh size in environmental quality assessment of estuarine macrobenthic communities

The Water Framework Directive (WFD) strengthened the need for environmental quality assessment with rapid and accurate results. Studies of estuarine benthic macrofauna communities often use 0.5-mm mesh sieves in samples processing. However, this represents a considerable increase in sampling and identification effort compared to the use of 1-mm mesh sieves. Therefore, it is relevant to determine if mesh size matters in environmental quality assessments.The objectives of this study were as follows: (i) to test whether sieves with different mesh sizes provided different environmental status assessments in transitional systems, (ii) to compare the performance of different ecological indicators based on data from 0.5- and 1-mm mesh sieves and (iii) to compare the costs involved in using these two mesh sizes.Data were collected in the fall of 2007 and winter of 2008 at four sampling stations located in the Mondego Estuary, Portugal. The relative performance of Margalef and Shannon–Wiener indices, AMBI—AZTI Marine Biotic Index, Pielou, Eco-Exergy and Specific Eco-Exergy indices was analysed. Additionally, the multimetric Benthic Assessment Tool (BAT) was applied. The samples from the 1-mm mesh sieve were processed 2.9 times faster than the samples from the 0.5-mm mesh sieves. As expected, the density, biomass and number of species retained in the 0.5-mm mesh sieve were significantly higher in both seasons than the density, biomass and number of species retained in the 1-mm mesh sieve. All indicators were significantly different for the two mesh sizes in at least one season. The Pielou index was significantly different for the two mesh sizes in both seasons. Most indices showed that the 0.5-mm mesh sieve captured more information from the study system. The first BAT analysis provided different Ecological Quality Status (EQS) assessments for the two mesh sizes. To use the EQS obtained from the 1-mm mesh sieve as a proxy for the EQS for the 0.5-mm mesh sieve, further modifications were done in terms of reference conditions and class boundary thresholds. Regarding the Mondego Estuary, the use of a 1-mm mesh sieve appeared to be advantageous on routine environmental quality assessment, giving unbiased results with relatively less effort. Nevertheless, the methodology needs further validation and additional tests.     

Spatial heterogeneity recognition in estuarine intertidal benthic macrofaunal communities: influence of sieve mesh-size and sampling depth

Estuarine intertidal soft-bottom macrobenthic infauna of the Tagus estuary was characterised using different mesh size sieves and sediment sampling depth. The study sampled 105 sites using a hand held 0.01 m² corer. The top layer (0–5 cm) was sieved through nested 1.0 and 0.5 mm meshes whereas the bottom layer (5–20 cm) was through a 1 mm mesh. The total survey took 26 taxa of more than 5800 individuals and a total wet weight biomass of over 650 g. The top layer, using both sieves, gathered 23 taxa (92% of the total), more than 5600 specimens (96%) but less than 8 g of biomass (1%) whereas the 1.0 mm sieve retained 21 taxa (91%), more than 1700 specimens (31%) and almost 7 g of biomass (1%). Abundance was dominated by small annelids, of which Streblospio shrubsolii was 68%, whereas biomass was dominated by molluscs, with the bivalve Scrobicularia plana representing 98%. Multivariate analyses showed an abundance pattern where the top layer data was very similar to that obtained with both layers. The bottom layer data were needed to accurately represent the total biomass pattern. The macrofaunal spatial pattern identified with the 0.5 mm sieve data differed from that identified by the 1.0 mm and was essential to discriminate a faunal assemblage located along the upper part of the shore. It was concluded that in order to characterize the macrofauna community structure, based on the presence/absence of taxa, the top layer and a 1.0 mm sieve would be sufficient. An abundance-based characterization requires the top layer and a 0.5 mm sieve whereas a biomass-based characterization requires data for both layers but it is sufficient to use the 1.0 mm sieve. Electronic supplementary material The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

Root length and biomass losses during sample preparation with different screen mesh sizes

Data are presented on the differences in root length density (RLD), dry matter (DM), and root diameter values determined on wheat and faba bean using sieves of different mesh size to separate roots from soil during sample preparation. Screens with 0.2, 1, and 2 mm (0.04, 1, and 4 mm²) aperture were used. Roots collected on the 2-mm sieve represented on average 55% of the weight and only 10% of the total length collected using a 0.2-mm sieve. With a 1-mm sieve 75% of weight was retained, but only 34% of the length. In the 0–20 cm soil layer average RLD and DM values ranged between 1.3 and 2.5 cm cm^-3 and 215 and 136 g m^-2 for faba bean and wheat respectively with 2 mm screens and 14.6 and 18.1 cm cm^-3 and 313 and 202 g m^-2 with 0.2 mm sieves. RLD was more affected than weight since losses from coarse screens were largely due to fine root fractions, although the 1-and 2-mm screens retained a small amount of fine roots that were long or attached to main structures. Variability was higher for measurements on coarser screens. The use of screens much coarser than the diameter of fine roots is not recommended for the study of surface-related phenomena in which root length quantification is necessary, while it may be acceptable for gross comparisons of root weight and spatial extent.     

Reducing the cost of benthic sample processing by using sieve retention probability models

Estimation of abundance or biomass of benthic invertebrates requires considerable effort to process samples. Consequently, it has been suggested to process only organisms retained by a relatively coarse meshed sieve and apply size-specific correction factors based on the probability that a sieve retains individual organisms. Benthic samples were collected from 10 sites in 2 regions and processed to validate an existing empirical model predicting sieve retention probabilities, to test whether periphyton biomass affects probability of retention, and to determine the optimal strategy that minimizes both cost and variability of estimates. The existing model predicting sieve retention probabilities corrected for organisms lost through sieves and mostly corrected for underestimation of biomass, but this model lead to overestimates of the frequency of the smallest organisms. Inclusion of algal biomass improved slightly the proportion of correct predictions (whether an organism is retained or not by a sieve) by 0.6% relative to the existing model (from 90.8% to 91.4%), and removed the bias. Density and biomass estimates obtained by only processing organisms retained by 1- or 2-mm sieves and applying correction factors derived from the predicted retention probabilities were accurate and only marginally less precise than estimates obtained by processing all organisms. The reduced precision of estimates from subsets of organisms could be compensated by increasing sample size and still lead to a reduction of 40–60% of the number of organisms processed. Even though the use of subsets introduces additional analytical variability, this variability is relatively small compared to the natural spatial variability among replicates. Handling editor: K. Martens     

The impact of dental impairment on ring-tailed lemur food processing performance

During mastication, foods are reduced into particles suitable for swallowing and digestion. Smaller particles possess a greater surface area per unit of volume on which digestive enzymes and bacteria may work than relatively larger particles, and are thus more readily digested. As dental morphology facilitates the breakdown of diets with specific mechanical properties, extensive dental wear and/or tooth loss may impede an individual's ability to break down and exploit foods. We present data demonstrating a relationship between dental impairment and particle size in 43 fecal samples from 33 ring-tailed lemurs at the Beza Mahafaly Special Reserve (BMSR), Madagascar. All fecal samples were sifted through three sieves of decreasing size (11.2 mm, 4.75 mm, and 1.0 mm). The resulting fraction in each sieve was then weighed and assessed in relation to individual dental impairment status. With increasing wear, the percentage of each sample within the 1.0 mm sieve decreases, whereas that in the 11.2 mm sieve increases with increasing postcanine wear, although these effects are not present when limited to individuals without tooth loss. Individuals with tooth loss also demonstrate larger proportions of fecal material 1.0-4.75 mm in size. Dental impairment results in larger food particles and potentially less efficient utilization of foods. When fecal material was examined by leaf vs. fruit content, individuals with tooth loss demonstrated reduced proportions of fruit in the 1.0 mm and 11.2 mm sieves. These data suggest individuals with tooth loss consume less fruit than those without loss, potentially reflecting a reduced ability to process tamarind fruit, a key fallback resource at BMSR.     

Sieve size effects on root length and biomass measurements of maize (Zea mays) and Grevillea robusta

The purpose of this study was to investigate the effects of different mesh sizes on the recovery of root length and biomass and to determine whether the degree of recovery was influenced by plant species and sample location. Sieves of 2.0, 1.0, 0.5 and 0.25 mm (4.0, 1.0, 0.25 and 0.06 mm2) mesh sizes were used to recover and measure the root length and biomass of Zea mays L. (maize) at 0–15 cm and 30–45 cm depths and of Grevillea robusta A. Cunn. ex R. Br. (grevillea) at the same depths 1.0 m and 4.5 m from a line of grevillea trees. At 0–15 cm, the coarser sieves (sum collected with 2.0 and 1.0 mm sieves) recovered approximately 80% of the total root biomass measured, but only 60% of the root length. The proportion of total maize root length and biomass recovered by the coarser sieves decreased with soil depth. The proportion of total grevillea root length recovered by the coarser sieves was similar at the two soil depths, but increased slightly with distance from the tree line. The ≥ 0.5 mm sieves recovered between 93 and 96% of grevillea and maize root biomass and between 73 and 98% of their root length, depending on the sample location. Roots passing through the 0.5 mm sieve, but recovered by the 0.25 mm sieve were about 20% of total maize root length and grevillea root length at 1.0 m from the tree line but < 5% of the total grevillea root length at 4.5 m from the tree. Roots passing through the 0.5 mm sieve but recovered by the 0.25 mm sieve contributed only slightly to root biomass. Although the ≥ 0.5 mm sieves provided adequate measurements of root biomass, the ≥ 0.25 mm sieves were required for accurate measurement of fine root length. There was no universal correction for root length and biomass underestimation when large sieve sizes were used because the proportions of length and biomass recovered depended on the plant species and on soil depth and distance from the plant. This revised version was published online in August 2006 with corrections to the Cover Date.     

Particle size distribution of distillers dried grains with solubles (DDGS) and relationships to compositional and color properties

Eleven distillers dried grains with solubles (DDGS), processed from yellow corn, were collected from different ethanol processing plants in the US Midwest area. Particle size distribution (PSD) by mass of each sample was determined using a series of six selected US standard sieves: Nos. 8, 12, 18, 35, 60, and 100, and a pan. The original sample and sieve sized fractions were measured for surface color and contents of moisture, protein, oil, ash, and starch. Total carbohydrate (CHO) and total non-starch CHO were also calculated. Results show that there was a great variation in composition and color among DDGS from different plants. Surprisingly, a few DDGS samples contained unusually high amounts of residual starch (11.1-17.6%, dry matter basis, vs. about 5% of the rest), presumably resulting from modified processing methods. Particle size of DDGS varied greatly within a sample and PSD varied greatly among samples. The 11 samples had a mean value of 0.660mm for the geometric mean diameter (d(gw)) of particles and a mean value of 0.440mm for the geometric standard deviation (S(gw)) of particle diameters by mass. The majority had a unimodal PSD, with a mode in the size class between 0.5 and 1.0mm. Although PSD and color parameters had little correlation with composition of whole DDGS samples, distribution of nutrients as well as color attributes correlated well with PSD. In sieved fractions, protein content, L and a color values negatively while contents of oil and total CHO positively correlated with particle size. It is highly feasible to fractionate DDGS for compositional enrichment based on particle size, while the extent of PSD can serve as an index for potential of DDGS fractionation. The above information should be a vital addition to quality and baseline data of DDGS.     

Factors affecting survival of mouse blastocysts vitrified by a mixture of ethylene glycol and dimethyl sulfoxide

The present study was conducted to determine suitable conditions for mouse blastocysts vitrified by a solution containing 25 % v/v (4.5M) ethylene glycol and 25% v/v (3.4M) dimethyl sulfoxide (VSi). In Experiment 1, blastocysts were exposed to 50% diluted VSi (50% VSi) for 10 minutes then to VSi for 0.5 minutes at room temperature (22 approximately 24 degrees C) or at 4 degrees C, followed by vitrification. The survival rates of these embryos exposed at each temperature were not significantly different. In Experiment 2, embryos were exposed directly to VSi for various time periods at room temperature and diluted in mPBS with 0.5 M sucrose without vitrification. The viability of embryos decreased after more than a 3 minute exposure. When the embryos were exposed to VSi for 0.5, 1, 1.5 and 2 minutes followed by vitrification, the survival rates were 78, 80, 76 and 50%, respectively. In Experiment 3, embryos were vitrified after exposure to 50% VSi for various time periods and then to VSi for 0.5 minutes at room temperature. One minute exposure to 50% VSi resulted in the highest survival rate. In Experiment 4 and 5, the cooling rate (from approximately 70 to approximately 2500 degrees C/minute), sucrose concentration (0, 0.5 and 1 M) of dilution solution, and dilution time (1 or 5 minutes) did not affect the viability of the vitrified embryos. Following exposure to 50% VSi for 1 minute and to VSi for 0.5 minutes at room temperature, embryos were cooled 1) at approximately 2500 degrees C/minute and diluted in 0.5 M sucrose in mPBS after warming or 2) at approximately 200 degrees C/minute and diluted in mPBS. In vivo development rates after the transfer to recipients were 38 and 42%, respectively. These values were similar to that of fresh control embryos.     

The bedding of laboratory animals as a source of airborne contaminants

In work environments with laboratory animals, the bedding of animals binds the excreta as well as other compounds originating from the animals and their environment. These may be generated into the ambient air when the personnel handle bedding in different procedures. This study compares the dustiness of different types of six clean and four soiled beddings from rat or mouse cages. The dust generation of clean bedding varied from <1 to 25 mg/m(3). When used in the cages of rats or mice for 4 days, the dust concentration of the beddings decreased, increased or stayed the same, depending on the type of bedding and animal species. A decrease in dustiness was, however, more common. The levels in the soiled beddings varied from <1 to 8.6 mg/m(3). In the case of the aspen chip bedding, the contents of bedding used in mouse, rat or rabbit cages were analysed for mesophilic bacteria and fungi, mycobacteria and endotoxins. All of these contaminants were variably found in the bedding samples, the maximal concentrations for bacteria were >6 500 000 colony-forming units (cfu)/g, for fungi 212 000 cfu/g, and for endotoxins 6500 ng/g (81 000 EU/g). The results showed that the bedding of laboratory animals may contain biologically effective compounds, and that these may be distributed into the ambient air depending on the characteristics of the bedding material. The dustiness of different bedding types is an important factor affecting the amount and quality of the occupational exposure of the personnel to airborne contaminants.     

Process performance of parallel bioreactors for batch cultivation of Streptomyces tendae

Batch cultivations of the nikkomycin Z producer Streptomyces tendae were performed in three different parallel bioreactor systems (milliliter-scale stirred-tank reactors, shake flasks and shaken microtiter plate) in comparison to a standard liter-scale stirred-tank reactor as reference. Similar dry cell weight concentrations were measured as function of process time in stirred-tank reactors and shake flasks, whereas only poor growth was observed in the shaken microtiter plate. In contrast, the nikkomycin Z production differed significantly between the stirred and shaken bioreactors. The measured product concentrations and product formation kinetics were almost the same in the stirred-tank bioreactors of different scale. Much less nikkomycin Z was formed in the shake flasks and MTP cultivations, most probably due to oxygen limitations. To investigate the non-Newtonian shear-thinning behavior of the culture broth in small-scale bioreactors, a new and simple method was applied to estimate the rheological behavior. The apparent viscosities were found to be very similar in the stirred-tank bioreactors, whereas the apparent viscosity was up to two times increased in the shake flask cultivations due to a lower average shear rate of this reactor system. These data illustrate that different engineering characteristics of parallel bioreactors applied for process development can have major implications for scale-up of bioprocesses with non-Newtonian viscous culture broths.     

Effect of media type and particle size on dissolved organic carbon release from woody filtration media

Sequential batch leaching tests were used to evaluate the mass of DOC released from composted garden organics (yard waste), pine and hardwood under pseudo-equilibrium conditions. All media showed an initial rapid decline in DOC values followed by a slower rate during later time periods. Greater than 50% of the DOC leached occurred within the initial time period (<24 h). The mass of DOC leached varied significantly between the materials and to a lesser degree between different particle size ranges. The pine had the lowest leached DOC fraction (2.8-4.8 mg/g), while the hardwood (21-27 mg/g) and compost (13.6-32.7 mg/g) were significantly greater. The type and processing of the woody material incorporated into these systems can have a significant impact on the treated stormwater.     

Drug release properties of polyethylene-glycol-treated ciprofloxacin-Indion 234 complexes

The polyethylene glycol (PEG) treatment of ciprofloxacin-Indion 234 complex was aimed to retard rapid ion exchange drug release at gastric pH. Ciprofloxacin loading on Indion 234 was performed in a batch process, and the amount of K⁺ in Indion 234 displaced by drug with time was studied as equilibrium constant K_DM. Drug-resin complex (DRC) was treated with aqueous PEG solution (0.5%–2% wt/vol) of different molecular weights (MWs) for 2 to 30 minutes. The PEG-treated ciprofloxacin-Indion 234 complex was evaluated for particle size, water absorption time, and drug release at gastric pH. During drug loading on Indion 234, the equilibrium constant (K_DM) increased rapidly up to 20 minutes with efficient drug loading. Increased time of immersion of the drug resinate in PEG solutions significantly retained higher size particles upon dehydration. The larger DRC particles showed longer water absorption times owing to compromised hydrating power. The untreated DRC showed insignificant drug release in deionized water; while at gastric pH, ciprofloxacin release was complete in 90 minutes. A trend of increased residual particle size, proportionate increase in water absorption time, and hence the retardation of release with time of immersion was evident in PEG-treated DRC. The time of immersion of DRC in PEG-treated DRC. The time of immersion of DRC in PEG solution had predominant release retardant effect, while the effect of molecular weight of PEG was insignificant. Thus, PEG treatment of DRC successfully retards ciprofloxacin ion exchange release in acidic pH.     

Influence of Matrix Composition on the Bioaccessibility of Copper,Zinc, and Nickel in Urban Residential Dust and Soil

This study examines factors affecting oral bioaccessibility of metals in household dust, in particular metal speciation, organic carbon content, and particle size, with the goal of addressing risk assessment information requirements. Investigation of copper (Cu) and zinc (Zn) speciation in two size fractions of dust (< 36 μ m and 80–150 μ m) using synchrotron X-ray absorption spectroscopy (XAS) indicates that the two metals are bound to different components of the dust: Cu is predominately associated with the organic phase of the dust, while Zn is predominately associated with the mineral fraction. Total and bioaccessible Cu, nickel (Ni), and Zn were determined (on dry weight basis) in the < 150 μ m size fraction of a set of archived indoor dust samples (n = 63) and corresponding garden soil samples (n = 66) from the City of Ottawa, Canada. The median bioaccessible Cu content is 66 μ g g^?1 in dust compared to 5 μ g g^?1 in soil; the median bioaccessible Ni content is 16 μ g g^?1 in dust compared to 2 μ g g^?1 in soil; and the median bioaccessible Zn content is 410 μ g g^?1 in dust compared to 18 μ g g^?1 in soil. For the same data set, the median total Cu content is 152 μ g g^?1 in dust compared to 17 μ g g^?1 in soil; the median total Ni content is 41 μ g g^?1 in dust compared to 13 μ g g^?1 in soil; and the median total Zn content is 626 μ g g^?1 in dust compared to 84 μ g g^?1 in soil. Organic carbon is elevated in indoor dust (median 28%) compared to soil (median 5%), and is a key factor controlling metal partitioning and therefore bioaccessibility. The results show that house dust and soil have distinct geochemical signatures and should not be treated as identical media in exposure and risk assessments. Separate measurements of the indoor and outdoor environment are essential to improve the accuracy of residential risk assessments.     

Sieve Element of Impatiens sultanii: 1. Wound Reaction

A Study of wound reaction of the metaphloem of the stem by white-light,fluorescence, and electron microscopy provides evidence forthe structure of mature sieve elements in the intact plant.Starch grains usually are retained in plastids which are locatedagainst the lateral walls of sieve elements and concentratedat both ends of each cell. Slime plugs and dense connectingstrands in the sieve plates seem to result from reactions tocutting or penetration of the killing agent; after appropriatemethods of killing, the contents of a connecting strand maybe only slightly denser, if any, than the milieu on either sideof the sieve plate. A strange accumulation of slime, consistingof streamers directed toward the wound surface from each sieveplate, occurred in tissue boiled immediately after incisionof the phloem. Callose is present in sieve elements of intactplants when the tissue is killed within 4 seconds after injury.Callose is accumulated in response to wounding in added amounts,but only after 5 minutes or more and only within about 15 sieveelements from the wound. Quantities of callose sufficient forplugging the sieve plate accumulate after 30 minutes or more.Sieve-plate callose and deposits on the nearby lateral wallsproduce a cup-shaped mass which is called a cup deposit.     

马尾松人工林土壤各粒径团聚体湿筛后的有机碳分配

选取25a、45a和65a马尾松人工林为研究对象,采用湿筛法对各粒径土壤团聚体分别湿筛。探究了马尾松人工林各粒径团聚体湿筛后的团聚体有机碳分配,以探讨各粒径团聚体湿筛后分配到同一粒级团聚体有机碳含量及其对团聚体水稳性的贡献差异。结果表明：种植年限增加显著降低土壤团聚体水稳性（P<0.05）;各粒径团聚体湿筛后分配的有机碳随粒级减小含量呈先降后增趋势,以保持原粒级团聚体有机碳（12.96-32.01 g/kg）含量最高,其次是<0.25 mm粒级（8.08-23.53 g/kg）。各粒径团聚体湿筛分配到同一粒级的有机碳以保持原粒级的含量最高（P<0.05）;土壤团聚体水稳性与各粒径团聚体湿筛后保持原粒径的有机碳呈显著或极显著正相关（P<0.05或0.01）,分配到越小的粒级正相关性越不显著。此外,团聚体水稳性与各粒径团聚体湿筛分配到同一粒级的有机碳呈正相关,以保持原粒级相关性最高（P<0.01或0.05）;回归方程及相关性系数表明,有机碳与保持原粒径团聚体呈显著呈或极显著正相关（P<0.05或0.01）,与消散到其他粒级的团聚体呈负相关或极显著负相关（P>0.05或<0.01）。本研究得出有机碳含量增加促进更大粒径团聚体形成。反之,促使大粒径团聚体向较小粒径团聚体转化。同一粒级团聚体间,保持原粒级团聚体比易转化形成更大粒级团聚体有更高的有机碳含量和更强的水稳性,这对团聚体的固碳提供了新的认识。     

Disturbance-Mediated Drift in Tree Functional Groups in Amazonian Forest Fragments

The interactive effects of forest disturbance and fragmentation on tropical tree assemblages remain poorly understood. We examined the effects of forest patch and landscape metrics, and levels of forest disturbance on the patterns of floristic composition and abundance of tree functional groups within 21 forest fragments and two continuous forest sites in southern Brazilian Amazonia. Trees were sampled within 60 (10 × 250 m) plots placed in the core areas of the fragments. Tree assemblage composition and abundance were summarized using nonmetric multidimensional scaling (NMDS). Forest patch size explained 36.2 percent and 30 percent of the variance in the proportion of small-seeded softwood and hardwood stems in the 21 forest patches, respectively. Large fragments retained a higher abundance of hardwood tree species whereas small-seeded softwood trees appear to proliferate rapidly in small disturbed fragments. Generalized linear mixed models showed that time since fragmentation had both positive and negative effects on the density of different functional groups of trees and on the ordination axes describing tree abundance. The composition and abundance of different tree genera were also related to time since fragmentation, distance to the nearest edge, and fire severity, despite the recent post-isolation history of the forest patches surveyed. Both the proliferation of fast-growing pioneer trees and the decline of hardwood trees found in our forest plots have profound consequences on the floristic composition, forest dynamics, carbon storage, and nutrient cycling in Amazonian forest fragments.