氨基磺酸应用于甘蔗渣预处理的研究

本研究尝试将氨基磺酸应用于甘蔗渣预处理,探究其作为酸预处理试剂对甘蔗渣成分和酶解的影响。氨基磺酸预处理最优条件为浓度3%,温度121℃,预处理1 h。在该条件下,甘蔗渣的固体回收率为64.45%,半纤维素和木质素去除率分别为70.81%和25.10%,纤维素损失率仅7.56%。与硫酸、盐酸预处理相比,氨基磺酸的半纤维素和木质素去除率不如硫酸、盐酸预处理,但固体回收率更高,纤维素损失率低,能保留更多纤维素有效成分。进一步酶解显示,氨基磺酸预处理的纤维素转化率高于硫酸、盐酸预处理。氨基磺酸作为一种新的酸预处理试剂,在木质纤维素降解上有良好应用前景。     

Dilute acid pretreatment of rye straw and bermudagrass for ethanol production

Ethanol production from lignocellulosic materials provides an alternative energy production system. Rye and bermudagrass that are used in hog farms for nutrient uptake from swine wastewater have the potential for fuel ethanol production because they have a relative high cellulose and hemicellulose content. Dilute sulfuric acid pretreatment of rye straw and bermudagrass before enzymatic hydrolysis of cellulose was investigated in this study. The biomass at a solid loading rate of 10% was pretreated at 121 degrees C with different sulfuric acid concentrations (0.6, 0.9, 1.2 and 1.5%, w/w) and residence times (30, 60, and 90 min). Total reducing sugars, arabinose, galactose, glucose, and xylose in the prehydrolyzate were analyzed. In addition, the solid residues were hydrolyzed by cellulases to investigate the enzymatic digestibility. With the increasing acid concentration and residence time, the amount of arabinose and galactose in the filtrates increased. The glucose concentration in the prehydrolyzate of rye straw was not significantly influenced by the sulfuric acid concentration and residence time, but it increased in the prehydrolyzate of bermudagrass with the increase of pretreatment severity. The xylose concentration in the filtrates increased with the increase of sulfuric acid concentration and residence time. Most of the arabinan, galactan and xylan in the biomass were hydrolyzed during the acid pretreatment. Cellulose remaining in the pretreated feedstock was highly digestible by cellulases from Trichoderma reesei.     

Effects of sulfuric acid loading and residence time on the composition of sugarcane bagasse hydrolysate and its use as a source of xylose for xylitol bioproduction

A 2(2) full factorial design was employed to evaluate the effects of sulfuric acid loading and residence time on the composition of sugarcane bagasse hydrolysate obtained in a 250-L reactor. The acid loading and the residence time were varied from 70 to 130 mg acid per gram of dry bagasse and from 10 to 30 min, respectively, while the temperature (121 degrees C) and the bagasse loading (10%) were kept constant. Both the sulfuric acid loading and the residence time influenced the concentrations of xylose and inhibitors in the hydrolysate. The highest xylose concentration (22.71 g/L) was achieved when using an acid loading of 130 mg/g and a residence time of 30 min. These conditions also led to increased concentrations of inhibiting byproducts in the hydrolysate. All of the hydrolysates were vacuum-concentrated to increase the xylose concentration, detoxified by pH alteration and adsorption into activated charcoal, and used for xylitol bioproduction in a stirred tank reactor. Neither the least (70 mg/g, 10 min) nor the most severe (130 mg/g, 30 min) hydrolysis conditions led to the best xylitol production (37.5 g/L), productivity (0.85 g/L h), and yield (0.78 g/g).     

Mild pretreatment of yellow poplar biomass using sequential dilute acid and enzymatically-generated peracetic acid to enhance cellulase accessibility

Biomass contains cellulose, xylan and lignin in a complex interwoven structure that hinders enzymatic hydrolysis of the cellulose. To separate these components in yellow poplar biomass, we sequentially pretreated with dilute sulfuric acid and enzymatically-generated peracetic acid. In the first step, the dilute acid with microwave heating (140°C, 5 min) hydrolyzed 90% of xylan. The xylose yield in hydrolysate after dilute acid pretreatment was 83.1%. In the second step, peracetic acid (60°C, 6 h) removed up to 80% of lignin. This sequential pretreatment fractionated biomass into xylan and lignin, leaving a solid residue enriched in cellulose (~80%). The sequential pretreatment enhanced enzymatic digestibility of the cellulase by removal of the other components in biomass. The glucose yield after enzymatic hydrolysis was 90.5% at a low cellulase loading (5 FPU/g of glucan), which is 1.6 and 18 times higher than for dilute acid-pretreated biomass and raw biomass, respectively. This novel sequential pretreatment with dilute acid and peracetic acid efficiently separates the three major components of yellow poplar biomass, and reduces the amount of cellulase needed.     

Dilute sulfuric acid cycle spray flow-through pretreatment of corn stover for enhancement of sugar recovery

A cycle spray flow-through reactor was designed and used to pretreat corn stover in dilute sulfuric acid medium. The dilute sulfuric acid cycle spray flow-through (DCF) process enhanced xylose sugar yields and cellulose digestibility while increasing the removal of lignin. Within the DCF system, the xylose sugar yields of 90–93% could be achieved for corn stover pretreated with 2% (w/v) dilute sulfuric acid at 95 °C during the optimal reaction time (90 min). The remaining solid residue exhibited enzymatic digestibility of 90–95% with cellulase loading of 60 FPU/g glucan that was due to the effective lignin removal (70–75%) in this process. Compared with flow-through and compress-hot water pretreatment process, the DCF method produces a higher sugar concentration and higher xylose monomer yield. The novel DCF process provides a feasible approach for lignocellulosic material pretreatment.     

The Influence of Hemicellulose and Lignin Removal on the Enzymatic Digestibility from Sugarcane Bagasse

Sugarcane bagasse (SCB) was pretreated with liquid hot water (LHW) and aqueous ammonia (AA), with the objective of investigating the influence of hemicellulose and lignin removal on the enzymatic digestibility and sugar recovery. The experimental results show that LHW and aqueous ammonia have a good performance in terms of hemicellulose dissolution and lignin removal respectively. The biggest xylan recovery of 74.3 % was obtained for LHW pretreatment at 160 °C, 5 %?w/v for 20 min with the xylan dissolution of 83.1 %. And the biggest lignin removal of 84.0 % was obtained for aqueous ammonia pretreatment at 160 °C, 10 %?w/v for 60 min. Moreover, the aperture and surface area of the sample were enlarged by the liquid hot water, which improves the accessibility of the substrate to the enzyme. The lignin removal caused by aqueous ammonia pretreatment can reduce the absorption of enzyme. In addition, the correlation between the compositional change and the enzymatic digestibility indicates that the removal of hemicellulose was more effective than lignin for destruction of the hemicellulose–lignin–cellulose structure.     

酵母发酵蔗渣半纤维素水解物生产木糖酶

采用二次正交旋转组合设计研究了蔗渣半纤维素水解过程中硫酸浓度与液 固比对木糖收率的影响。回归分析表明 ,这两个因素与木糖的收率之间存在显著的回归关系。通过回归方程优化水解条件 ,当硫酸浓度 2 .4g L ,液 固 =6 .2 ,在蒸汽压力 2 .5× 10 4Pa的条件下水解 2 .5h ,10 0g蔗渣可水解生成木糖约 2 4g。大孔树脂吸附层析处理蔗渣半纤维素水解物 ,能有效地减少其中的酵母生长抑制物含量 ,显著改善水解物的发酵性能。用大孔树脂在pH 2条件下处理过的蔗渣半纤维素水解物作基质 ,含木糖 2 0 0g L ,产木糖醇酵母菌株CandidatropicalisAS2 .1776发酵 110h耗完基质中的木糖 ,生成木糖醇 12 7g L ,产物转化率 0 .6 4(木糖醇g 木糖g) ,产物生成速率 1.15g L·h .     

Two-stage pretreatment of rice straw using aqueous ammonia and dilute acid

Liberation of fermentable sugars from recalcitrant lignocellulosic biomass is one of the key challenges in production of cellulosic ethanol. Here we developed a two-stage pretreatment process using aqueous ammonia and dilute sulfuric acid in a percolation mode to improve production of fermentable sugars from rice straw. Aqueous NH? was used in the first stage which removed lignin selectively but left most of cellulose (97%) and hemicellulose (77%). Dilute acid was applied in the second stage which removed most of hemicellulose, partially disrupted the crystalline structure of cellulose, and thus enhanced enzymatic digestibility of cellulose in the solids remaining. Under the optimal pretreatment conditions, the enzymatic hydrolysis yields of the two-stage treated samples were 96.9% and 90.8% with enzyme loadings of 60 and 15FPU/g of glucan, respectively. The overall sugar conversions of cellulose and hemicellulose into glucose and xylose by enzymatic and acid hydrolysis reached 89.0% and 71.7%, respectively.     

Steam pretreatment of H(2)SO(4)-impregnated Salix for the production of bioethanol

In the bioconversion of lignocellulosic materials to ethanol, pretreatment of the material prior to enzymatic hydrolysis is essential to obtain high overall yields of sugar and ethanol. In this study, steam pretreatment of fast-growing Salix impregnated with sulfuric acid has been investigated by varying the temperature (180-210 degrees C), the residence time (4, 8 or 12 min), and the acid concentration (0.25% or 0.5% (w/w) H(2)SO(4)). High sugar recoveries were obtained after pretreatment, and the highest yields of glucose and xylose after the subsequent enzymatic hydrolysis step were 92% and 86% of the theoretical, respectively, based on the glucan and xylan contents of the raw material. The most favorable pretreatment conditions regarding the overall sugar yield were 200 degrees C for either 4 or 8 min using 0.5% sulfuric acid, both resulting in a total of 55.6g glucose and xylose per 100g dry raw material. Simultaneous saccharification and fermentation experiments were performed on the pretreated slurries at an initial water-insoluble content of 5%, using ordinary baker's yeast. An overall theoretical ethanol yield of 79%, based on the glucan and mannan content in the raw material, was obtained.     

Hydrothermal pretreatment of sugarcane bagasse using response surface methodology improves digestibility and ethanol production by SSF

Sugarcane bagasse was characterized as a feedstock for the production of ethanol using hydrothermal pretreatment. Reaction temperature and time were varied between 160 and 200°C and 5–20 min, respectively, using a response surface experimental design. The liquid fraction was analyzed for soluble carbohydrates and furan aldehydes. The solid fraction was analyzed for structural carbohydrates and Klason lignin. Pretreatment conditions were evaluated based on enzymatic extraction of glucose and xylose and conversion to ethanol using a simultaneous saccharification and fermentation scheme. SSF experiments were conducted with the washed pretreated biomass. The severity of the pretreatment should be sufficient to drive enzymatic digestion and ethanol yields, however, sugars losses and especially sugar conversion into furans needs to be minimized. As expected, furfural production increased with pretreatment severity and specifically xylose release. However, provided that the severity was kept below a general severity factor of 4.0, production of furfural was below an inhibitory concentration and carbohydrate contents were preserved in the pretreated whole hydrolysate. There were significant interactions between time and temperature for all the responses except cellulose digestion. The models were highly predictive for cellulose digestibility (R ² = 0.8861) and for ethanol production (R ² = 0.9581), but less so for xylose extraction. Both cellulose digestion and ethanol production increased with severity, however, high levels of furfural generated under more severe pretreatment conditions favor lower severity pretreatments. The optimal pretreatment condition that gave the highest conversion yield of ethanol, while minimizing furfural production, was judged to be 190°C and 17.2 min. The whole hydrolysate was also converted to ethanol using SSF. To reduce the concentration of inhibitors, the liquid fraction was conditioned prior to fermentation by removing inhibitory chemicals using the fungus Coniochaeta ligniaria.     

Efficient conversion of sugarcane stalks into ethanol employing low temperature alkali pretreatment method

An alternative route for bio-ethanol production from sugarcane stalks (juice and bagasse) featuring a previously reported low temperature alkali pretreatment method was evaluated. Test-tube scale pretreatment-saccharification experiments were carried out to determine optimal LTA pretreatment conditions for sugarcane bagasse with regard to the efficiency of enzymatic hydrolysis of the cellulose. Free fermentable sugars and bagasse recovered from 2 kg of sugarcane stalks were jointly converted into ethanol via separate enzymatic hydrolysis and fermentation (SHF). Results showed that 98% of the cellulose present in the optimally pretreated bagasse was hydrolyzed into glucose after 72-h enzymatic saccharification using commercially available cellulase and β-glucosidase preparations at relatively low enzyme loading. The fermentable sugars in the mixture of the sugar juice and the bagasse hydrolysate were readily converted into 193.5 mL of ethanol by Saccharomyces cerevisiae within 12h, achieving 88% of the theoretical yield from the sugars and cellulose.     

Enzymatic digestion of alkaline‐sulfite pretreated sugar cane bagasse and its correlation with the chemical and structural changes occurring during the pretreatment step

Sugar cane bagasse is recalcitrant to enzymatic digestion, which hinders the efficient conversion of its polysaccharides into fermentable sugars. Alkaline‐sulfite pretreatment was used to overcome the sugar cane bagasse recalcitrance. Chemical and structural changes that occurred during the pretreatment were correlated with the efficiency of the enzymatic digestion of the polysaccharides. The first 30 min of pretreatment, which removed approximately half of the initial lignin and 30% of hemicellulose seemed responsible for a significant enhancement of the cellulose conversion level, which reached 64%. After the first 30 min of pretreatment, delignification increased slightly, and hemicellulose removal was not enhanced; however, acid groups continued to be introduced into the residual lignin. Water retention values were 145% to the untreated bagasse and 210% to the bagasse pretreated for 120 min and fiber widths increased from 10.4 to 30 μm, respectively. These changes were responsible for an additional increase in the efficiency of enzymatic hydrolysis of the cellulose, which reached 92% with the 120 min pretreated sample. © 2013 American Institute of Chemical Engineers Biotechnol. Prog., 29:890–895, 2013     

Dilute acid pretreatment of barley straw and its saccharification and fermentation

In this study, the optimization of the major factors for efficient dilute acid pretreatment (DAP) of Korean barley straw was conducted by response surface method (RSM). In addition, saccharification of the optimized pretreated barley straw as well as fermentation of solubilized hemicellulose and enzymatic hydrolysates was performed for bioethanol production. The factors optimized by RSM were concentration of sulfuric acid, reaction time and temperature. Optimization experiments were carried out within the scope of 0.16 ∼ 1.84% sulfuric acid, 10 ∼ 20 min of reaction time, and 116 ∼ 183°C of temperature using a statistical program, and optimal conditions (1.16% of sulfuric acid, 16.9 min of reaction time, and 150°C) were determined based on reliable statistical indicators. The predicted value at stationary point and the experimental value were 81.38 and 80.66%, respectively. Saccharification was performed at 50°C using Celluclast (cellulase) and Novozyme 188 (β-glucosidase) as biocatalysts in an enzyme loading test. Conversion of the saccharification process was approximately 65%. In addition, fermentation of glucose after saccharification and solubilization of xylose solution by DAP were performed using Saccharomyces cerevisiae and Pichia stipitis at 30°C and 200 rpm for 12 h.     

Pretreatment of waste newspaper using ethylene glycol for bioethanol production

Pretreatment using ethylene glycol was investigated to enhance the enzyme digestibility of wastepaper. The pretreatment was conducted over a wide range of conditions including sulfuric acid concentrations of 1.3 ∼ 4.7%, temperatures of 143.2 ∼ 176.7°C and reaction time of 1.6 ∼ 18.4 min. The optimum conditions were around 2% sulfuric acid, 150°C and 15 min. At these conditions, 60 and 75% of hemicellulose and lignin, respectively, were removed while cellulose remained intact. Additionally, an enzyme digestibility of 94% was achieved. From the substrate dissolution analysis, the dissolution yield was strongly related to the enzymatic digestibility and the removal of cellulose, hemicellulose and lignin. Also, the dissolution yield was directly related to the severity parameter, which provides a quantitative prediction of the intensity of a reaction. Recycling and re-use of ethylene glycol were also studied. Ethylene glycol could be recycled and re-used at least four times without significantly lowering the pretreatment performance.     

Characterization of dilute acid pretreatment of silvergrass for ethanol production

Pretreatment with dilute sulfuric acid of silvergrass was compared with the pretreatment's effect on other commonly used lignocellulosic materials, namely rice straw and bagasse, in order to evaluate the potential of this feedstock for ethanol production. The highest yield of xylose from silvergrass was between 70% and 75%, which was similar to bagasse. However, silvergrass gave a higher level of fermentability than bagasse using the hydrolysate because less acetic acid was formed. The release of sugars resulted in an about 2.0-fold increase in specific surface area of the pretreated silvergrass. Increasing the specific surface area did not obviously enhance enzymatic digestibility. The hydrophilicity of the acid pretreated silvergrass was characterized using its Fourier transform infrared (FTIR) spectra. The increase in hydrophilicity may enhance enzymatic adsorption onto lignin and increase the accumulation of cellobiose for enzymatic hydrolysis as pretreatment severity increases.     

Evaluation of fermentative potential of <Emphasis Type="Italic">Kluyveromyces marxianus</Emphasis> ATCC 36907 in cellulosic and hemicellulosic sugarcane bagasse hydrolysates on xylitol and ethanol production

This paper evaluates the fermentative potential of Kluyveromyces marxianus grown in sugarcane bagasse cellulosic and hemicellulosic hydrolysates obtained by acid hydrolysis. Ethanol was obtained from a single glucose fermentation product, whereas xylose assimilation resulted in xylitol as the main product and ethanol as a by-product derived from the metabolism of this pentose. Fermentation performed in a simulated hydrolysate medium with a glucose concentration similar to that of the hydrolysate resulted in ethanol productivity (Qp?=?0.86 g L^?1 h^?1) that was tenfold higher than the one observed in the cellulosic hydrolysate. However, the use of hemicellulosic hydrolysate favored xylose assimilation in comparison with simulated medium with xylose and glucose concentrations similar to those found in this hydrolysate, without toxic compounds such as acetic acid and phenols. Under this condition, xylitol yield was 53.8 % higher in relation to simulated medium. Thus, the total removal of toxic compounds from the hydrolysate is not necessary to obtain bioproducts from lignocellulosic hydrolysates.     

Effect of dilute acid pretreatment on the saccharification and fermentation of rye straw

This research shows the effect of dilute acid pretreatment with various sulfuric acid concentrations (0.5–2.0% [wt/vol]) on enzymatic saccharification and fermentation yield of rye straw. After pretreatment, solids of rye straw were suspended in Na citrate buffer or post-pretreatment liquids (prehydrolysates) containing sugars liberated after hemicellulose hydrolysis. Saccharification was conducted using enzymes dosage of 15 or 25 FPU/g cellulose. Cellulose saccharification rate after rye straw pretreatment was enhanced by performing enzymatic hydrolysis in sodium citrate buffer in comparison with hemicellulose prehydrolysate. The maximum cellulose saccharification rate (69%) was reached in sodium citrate buffer (biomass pretreated with 2.0% [wt/vol] H₂SO₄). Lignocellulosic complex of rye straw after pretreatment was subjected to separate hydrolysis and fermentation (SHF) or separate hydrolysis and co-fermentation (SHCF). The SHF processes conducted in the sodium citrate buffer using monoculture of Saccharomyces cerevisiae (Ethanol Red) were more efficient compared to hemicellulose prehydrolysate in respect with ethanol yields. Maximum fermentation efficiency of SHF processes obtained after rye straw pretreatment at 1.5% [wt/vol] H₂SO₄ and saccharification using enzymes dosage of 25 FPU/g in sodium citrate buffer, achieving 40.6% of theoretical yield. However, SHCF process using cocultures of pentose-fermenting yeast, after pretreatment of raw material at 1.5% [wt/vol] H₂SO₄ and hydrolysis using enzymes dosage of 25 FPU/g, resulted in the highest ethanol yield among studied methods, achieving 9.4 g/L of ethanol, corresponding to 55% of theoretical yield.     

Characterization of enzymatic saccharification for acid-pretreated lignocellulosic materials with different lignin composition

The enzymatic saccharification of three different feedstocks, rice straw, bagasse and silvergrass, which had been pretreated with different dilute acid concentrations, was studied to verify how enzymatic saccharification was affected by the lignin composition of the raw materials. There was a quantitatively inverse correlation between lignin content and enzymatic digestibility after pretreatment with 1%, 2% and 4% sulfuric acid. The lignin accounted for about 18.8–21.8% of pretreated rice straw, which was less than the 23.1–26.5% of pretreated bagasse and the 21.5–24.1% of pretreated silvergrass. The maximum glucose yield achieved, under an enzyme loading 6.5 FPU g^?1 DM for 72 h, was close to 0.8 g glucose/g glucan from the enzymatic hydrolysis of the pretreated rice straw; this was twice that from bagasse and silvergrass. A decrease in initial rate of glucose production was observed in all cases when the raw materials underwent enzymatic saccharification with 4% sulfuric acid pretreatment. It is suggested that the higher acid concentration led to an inhibition of β-glucosidase activity. Fourier transform infrared (FTIR) spectroscopy further indicated the chemical properties of the rice straw and silvergrass become more hydrophilic after pretreatment using 2% of sulfuric acid, but the pretreated bagasse tended to become more hydrophobic. The hydrophilic nature of the pretreated solid residues may increase the inhibitive effects of lignin on the cellulase and this could become very important for raw materials such as silvergrass that contain more lignin.     

Combination of dilute acid and ionic liquid pretreatments of sugarcane bagasse for glucose by enzymatic hydrolysis

Loss of hemicellulose and inability to effectively decrystallize cellulose, result in low yield and high cost of sugars derived from biomass. In this work, dilute sulfuric acid pretreatment could easily remove most of hemicellulose as sugars. The sugars were successfully used for 2,3-butanediol production with relative high yield (36.1%). Then, the remained solid residue after acid-pretreatment was further pretreated by ionic liquid (IL) to decrease its crystallinity for subsequent enzymatic saccharification. The combination of dilute acid- and IL-pretreatments resulted in significant higher glucose yield (95.5%) in enzymatic saccharification, which was more effective than using dilute acid- or IL-pretreatment alone. This strategy seems a promising route to achieve high yield of sugars from both hemicellulose and cellulose for biorefinery.     

Enhanced Bioethanol Production from Blue Agave Bagasse in a Combined Extrusion–Saccharification Process

This paper describes an improved process for bioethanol production using a recently developed combined extrusion–saccharification technology. Blue agave bagasse (BAB) was pretreated via a thermo-mechano-chemical process (co-rotational twin-screw, reactive extrusion) to increase the availability of cellulose and hemicellulose for enzymatic saccharification. Then, several commercial enzyme preparations, boosted with accessory enzymes (exoglucanase, endoglucanase, hemicellulase, xylanase, and β-glucosidase), were tested with extruded BAB at 5 % consistency in a stirred vessel. The enzyme blend that produced the highest saccharification yield was evaluated at different BAB consistencies. The obtained concentration of sugars increased up to 69.5 g/L (73 % yield) when a 20 % BAB mixture was used. When the enzyme blend was fed into the extruder and with a residence time of 2 min, the yield reached 15 % of the maximum theoretical of C6 sugars along this step. This extruded and pre-saccharified BAB was further hydrolyzed and used for fermentation. The pre-saccharification step significantly enhanced cellulose degradation and ethanol production. Our results indicate that the enzymatic saccharification of BAB, coupled with reactive extrusion, produces an excellent substrate for bioethanol production.