Performance comparison of ethanol and butanol production in a continuous and closed-circulating fermentation system with membrane bioreactor

Since both ethanol and butanol fermentations are urgently developed processes with the biofuel-demand increasing, performance comparison of aerobic ethanol fermentation and anerobic butanol fermentation in a continuous and closed-circulating fermentation (CCCF) system was necessary to achieve their fermentation characteristics and further optimize the fermentation process. Fermentation and pervaporation parameters including the average cell concentration, glucose consumption rate, cumulated production concentration, product flux, and separation factor of ethanol fermentation were 11.45?g/L, 3.70?g/L/h, 655.83?g/L, 378.5?g/m²/h, and 4.83, respectively, the corresponding parameters of butanol fermentation were 2.19?g/L, 0.61?g/L/h, 28.03?g/L, 58.56?g/m²/h, and 10.62, respectively. Profiles of fermentation and pervaporation parameters indicated that the intensity and efficiency of ethanol fermentation was higher than butanol fermentation, but the stability of butanol fermentation was superior to ethanol fermentation. Although the two fermentation processes had different features, the performance indicated the application prospect of both ethanol and butanol production by the CCCF system.     

Ethanol production from eucalyptus wood hemicellulose hydrolysate by Pichia stipitis

Ethanol production was evaluated from eucalyptus wood hemicellulose acid hydrolysate using Pichia stipitis NRRL Y-7124. An initial lag phase characterized by flocculation and viability loss of the yeast inoculated was observed. Subsequently, cell regrowth occurred with sequential consumption of sugars and production of ethanol. Polyol formation was detected. Acetic acid present in the hydrolysate was an important inhibitor of the fermentation, reducing the rate and the yield. Its toxic effect was due essentially to its undissociated form. The fermentation was more effective at an oxygen transfer rate between 1.2 and 2.4 mmol/L h and an initial pH of 6.5. The hydrolysate used in the experiences had the following composition (expressed in grams per liter): xylose 30, arabinose 2.8, glucose 1.5, galactose 3.7, mannose 1.0, cellobiose 0.5, acetic acid 10, glucuronic acid 1.5, and galacturonic acid 1.0. The best values obtained were maximum ethanol concentration 12.6 g/L, fermentation time 75 h, fermentable sugar consumption 99% ethanol yield 0.35 g/g sugars consumed, and volumetric ethanol productivity 4 g/L day. (c) 1992 John Wiley & Sons, Inc.     

Pervaporative stripping of acetone, butanol and ethanol to improve ABE fermentation

Acetone-butanol-ethanol fermentation by anaerobic bacterium C. acetobutylicum is a potential source for feedstock chemicals. The problem of product induced inhibition makes this fermentation economically infeasible. Pervaporation is studied as an effective separation technique to remove the toxic inhibitory products. Various membranes like Styrene Butadiene Rubber (SBR), Ethylene Propylene Diene Rubber (EPDM), plain Poly Dimethyl Siloxane (PDMS) and silicalite filled PDMS were studied for the removal of acetone, butanol and ethanol, from binary aqueous mixtures and from a quaternary mixture. It was found that the overall performance of PDMS filled with 15% w/w of silicalite was the best for removal of butanol in binary mixture study. SBR performance was best for the quaternary mixture studied.     

Acetone, butanol and ethanol production from domestic organic waste by solventogenic clostridia

Domestic organic waste (DOW) was washed and dried to 85 % dryness by VAM (The Netherlands). This material contained 25.1 g glucose, 8.4 g xylose and 5.8 g other monosaccharides/100 g dry matter. Using Mansonite steam explosion and enzymatic hydrolysis, a hydrolysate containing 15.4 g glucose, 2.2 g xylose and 0.8 g other monosaccharides per l was made. Clostridium acetobutylicum DSM 1731 produced 1.5 and C. beijerinckii B-592 0.9 g/l ABE and Clostridium LMD 84.48 1.9 g/l IBE, respectively, from this hydrolysate without further supplementation. Incubation with 2 fold concentrated hydrolysate completely impaired ABE production. After removal of unspecific inhibiting components, the yield of ABE production by Clostridium acetobutylicum DSM 1731 increased about 3 fold as compared to the nontreated hydrolysate. From 4 fold concentrated, partially purified, hydrolysate containing 34.2 g glucose/l, ABE production was 9.3 g/l after 120 h as compared to 3.2 g ABE/I from non-concentrated hydrolysate which contained 12.0 g glucose/l after elution over the same column. The concentration of butyric acid in the fermented hydrolysates was 2.2 and 0.4 g/l, respectively. This reasonably low amount of butyric acid showed that the fermentation had proceeded quite well.     

微生物耐受乙醇与丁醇机制及其在生物燃料生产与生物转化中的应用

生物法获取乙醇与丁醇过程中有机溶剂的毒性是生产菌重要环境胁迫因素之一,且当有机溶剂超过一定浓度时便会抑制微生物的生长,甚至引起微生物的死亡,因此提高工业微生物的有机溶剂耐受性对工业生产具有重要的意义。对微生物乙醇及丁醇耐受机制的研究可为选育具有较强溶剂耐受菌提供理论基础。本文系统介绍了微生物耐受乙醇与丁醇的机制,并对其在生物燃料生产及生物转化中面临的机遇与挑战等问题进行简要的评述。     

Optimization of fermentation conditions for ethanol production from whey

Summary Optimal conditions for ethanol production in 7% whey solutions by the yeast Candida pseudotropicalis ATCC 8619 included initial pH of 4.57 and 30°C. Complete fermentation of the available lactose took place without supplementary nutrients; additions of nitrogen or phosphorus salts, yeast extract or corn steep liquor resulted in increased yeast production and lower ethanol yields. A positive correlation was observed between increases in yeast inocula and lactose utilization and ethanol production rates; 8.35 g/l of ethanol was obtained within 22 h by using yeast inoculum of 13.9 g/l. No differences in fermentation rates or ethanol yields were observed when whole or deproteinized whey solutions were used. Concentrated whey permeates, obtained after removal of the valuable proteins from whey, can be effectively fermented for ethanol production.     

Production of acetone,butanol and ethanol (ABE) from potato wastes: fermentation with integrated membrane extraction

The technical possibilities of the microbial production of acetone, butanol and ethanol (ABE) from potato waste using in-line solvent recovery, are evaluated. Clostridium acetobutylicum DSM 1731 produces up to 20 g·l^–1 of solvents when grown on a medium containing 14% (w/v) potato powder. Using a polypropylene perstraction system and a oleyl alcohol/decane mixture as the extractant, the product yield (based on total solvents and potato dry weight) increased from 0.13 g·g^–1 to 0.23 g·g^–1. The recovery system worked well for 50 h, after which membrane fouling frustrated proper operation. In the second system a microfiltration step was incorporated whereas the solvents were extracted through a hydrophilic membrane using fatty acid methyl esters from sunflower oil as an extractant. This process configuration resulted in a comparable increase of ABE production. Correspondence to: G. Eggink     

Optimization of butanol production from tropical maize stalk juice by fermentation with Clostridium beijerinckii NCIMB 8052

Mixed sugars from tropical maize stalk juice were used to carry out butanol fermentation with Clostridium beijerinckii NCIMB 8052. Batch experiments employing central composite design (CCD) and response surface methodology (RSM) optimization were performed to evaluate effects of three factors, i.e. pH, initial total sugar concentration, and agitation rate on butanol production. Optimum conditions of pH 6.7, sugar concentration 42.2 g/L and agitation rate 48 rpm were predicted, under which a maximum butanol yield of 0.27 g/g-sugar was estimated. Further experiments demonstrated that higher agitation facilitated acetone production, leading to lower butanol selectivity in total acetone–butanol–ethanol (ABE). While glucose and fructose are more preferable by C. beijerinckii, sucrose can also be easily degraded by the microorganism. This study indicated that RSM is a useful approach for optimizing operational conditions for butanol production, and demonstrated that tropical maize, with high yield of biomass and stalk sugars, is a promising biofuel crop.     

Anaerobic bio-hydrogen production from ethanol fermentation: the role of pH

Hydrogen was produced by an ethanol-acetate fermentation at pH of 5.0 +/- 0.2 and HRT of 3 days. The yield of hydrogen was 100-200 ml g Glu(-1) with a hydrogen content of 25-40%. This fluctuation in the hydrogen yield was attributed to the formation of propionate and the activity of hydrogen utilizing methanogens. The change in the operational pH for the inhibition of this methanogenic activity induced a change in the main fermentation pathway. In this study, the main products were butyrate, ethanol and propionate, in the pH ranges 4.0-4.5, 4.5-5.0 and 5.0-6.0, respectively. However, the activity of all the microorganisms was inhibited below pH 4.0. Therefore, pH 4.0 was regarded as the operational limit for the anaerobic bio-hydrogen production process. These results indicate that the pH plays an important role in determining the type of anaerobic fermentation pathway in anaerobic bio-hydrogen processes.     

Improvement of acetone,butanol, and ethanol production from woody biomass using organosolv pretreatment

Bioprocess and Biosystems Engineering - A suitable pretreatment is a prerequisite of efficient acetone–butanol–ethanol (ABE) production from wood by Clostridia. In this study,...     

海带发酵制取生物乙醇的影响因素与优化条件

针对海带的碳水化合物不易被单一菌株发酵转化为乙醇的难题,通过酸化、匀浆和消化等预处理和正交试验,利用多酶系多菌种微生物复合发酵剂的酿酒曲,研究海带发酵制取生物乙醇的影响因素与优化条件。结果表明:在预处理试验中,加入一定量的Na2CO3,可以提高海带液中还原性糖和总糖的含量;消化温度对总糖影响相对较大,而对还原性糖的影响较小;过滤不利于得到较高浓度的乙醇;在优化条件中,发酵液的初始酸碱度是最重要的,其次是发酵温度和基质浓度,发酵液体积的影响程度相对较小。在基质(海带)质量浓度为0.15 g/L、温度34℃、起始pH 6.5和发酵液体积200 mL时,可以获得最大的乙醇产量4.09 g(以100 g海带计)。     

Bench-scale bioethanol production from eucalyptus by high solid saccharification and glucose/xylose fermentation method

In the bioethanol production process, high solid saccharification and glucose/xylose co-fermentation are important technologies for obtaining increased ethanol concentrations; however, bench-scale studies using combinations of these methods are limited. In this study, we hydrolyzed high solid concentration of milled eucalyptus using commercial enzymes and obtained 138.4 g/L total monomeric sugar concentration. These sugars were fermented to 53.5 g/L of ethanol by a xylose-utilizing recombinant Saccharomyces cerevisiae strain, MA-R4. These experiments were performed in bench scale (using 50 L scale solid mixer and 70 L scale fermenter). The results obtained in this study were comparable to our previous results in laboratory scale, indicating that we successfully achieved an efficient high solid saccharification and glucose/xylose co-fermentation system in bench scale.     

Modelling ethanol production from cellulose: separate hydrolysis and fermentation versus simultaneous saccharification and fermentation

In ethanol production from cellulose, enzymatic hydrolysis, and fermentative conversion may be performed sequentially (separate hydrolysis and fermentation, SHF) or in a single reaction vessel (simultaneous saccharification and fermentation, SSF). Opting for either is essentially a trade-off between optimal temperatures and inhibitory glucose concentrations on the one hand (SHF) vs. sub-optimal temperatures and ethanol-inhibited cellulolysis on the other (SSF). Although the impact of ethanol on cellobiose hydrolysis was found to be negligible, formation of glucose and cellobiose from cellulose were found to be significantly inhibited by ethanol. A previous model for the kinetics of enzymatic cellulose hydrolysis was, therefore, extended with enzyme inhibition by ethanol, thus allowing a rational evaluation of SSF and SHF. The model predicted SSF processing to be superior. The superiority of SSF over SHF (separate hydrolysis and fermentation) was confirmed experimentally, both with respect to ethanol yield on glucose (0.41 g g^?1 for SSF vs. 0.35 g g^?1 for SHF) and ethanol production rate, being 30% higher for an SSF type process. High conversion rates were found to be difficult to achieve since at a conversion rate of 52% in a SSF process the reaction rate dropped to 5% of its initial value. The model, extended with the impact of ethanol on the cellulase complex proved to predict reaction progress accurately.     

Continuous ethanol production from concentrated wood hydrolysates in an internal membrane-filtration bioreactor

Continuous culture for the production of ethanol from wood hydrolysate was carried out in an internal membrane-filtration bioreactor. The hydrolysate medium was sterilized at a relatively low temperature of 60 degrees C with the intention of reducing the formation of inhibitory compounds during the sterilization. The maximum ethanol concentration and productivity obtained in this study were 76.9 g/L and 16.9 g/L-h, respectively, which were much higher than those (57.2-67 g/L and 0.3-1.0 g/L-h) obtained in batch cultures using hydrolysate media sterilized at 60 degrees C. The productivity was also found to be much higher than that (6.7 g/L-h) obtained in a continuous cell retention culture using a wood hydrolysate sterilized at 121 degrees C. These results show that the internal membrane-filtration bioreactor in combination with low-temperature sterilization could be very effective for ethanol production from wood hydrolysate.     

Technology and economics of ethanol production from fodder beets via solid-phase fermentation

Summary Operating conditions for our semi-continuous, solid-phase fermentation system were optimized for conversion of fodder beets to fuel ethanol and distiller's wet feed (DWF). This information was then used to estimate operating parameters achievable in a commercial plant, and likely baseline production costs of such a plant. Initial acidification of pulp to pH 2.9–3.2 was effective in controlling bacterial contamination. The maximum operating capacity of the fermentor was approximately 92%, with 75% used for commercial application. A fermentation time of 24 h was sufficient to completely ferment the beet pulp to 8–9% (v/v) ethanol. Based on these parameters, a fodder beet cost of $19.25/metric ton ($17.50/ton), other operating and capital costs, and a PF credit of $0.14/L ($0.53/gal), ethanol production costs were estimated to be $0.49/L ($1.87/gal).     

Techno-economical study of ethanol and biogas from spruce wood by NMMO-pretreatment and rapid fermentation and digestion

Given that N-methylmorpholine-N-oxide (NMMO) is a promising alternative for the pretreatment of lignocelluloses, a novel process for ethanol and biogas production from wood was developed. The solvent, NMMO, is concentrated by multistage evaporation, and the wood is pretreated with the concentrated NMMO. Thereafter, ethanol is produced by the non-isothermal simultaneous saccharification and fermentation (NSSF) method, which is a rapid and efficient process. The wastewater is treated by upflow anaerobic sludge blanket (UASB) digester for rapid production of biogas. The process was simulated by Aspen plus®. Using mechanical vapor recompression for evaporators in the pretreatment and multi-pressure distillation columns, the energy requirements for the process were minimized. The economical feasibility of the developed biorefinery for five different plant capacities was studied by Aspen Icarus Process Evaluator. The base case was designed to utilize 200,000 tons of spruce wood per year and required M€ 58.3 as the total capital investment, while the production cost of ethanol is calculated to be €/l 0.44.     

Aeration alleviates ethanol inhibition and glycerol production during fed-batch ethanol fermentation

In this study, we investigated the effects of aeration on ethanol inhibition and glycerol production during fed-batch ethanol fermentation. When aeration was conducted at 0.13, 0.33, and 0.8 vvm, the ethanol productivity, specific ethanol production rate, and ethanol yield in the presence of greater than 100 g/L of ethanol were higher than when aeration was not conducted. In addition, estimation of the parameters (α and β) in a model equation of ethanol inhibition kinetics indicated that aeration alleviated ethanol inhibition against the specific growth rate and the specific ethanol production rate. Specifically, when aeration was conducted, the glycerol yield and specific glycerol production rate decreased approximately 50 and 70%, respectively. Finally, the results of this study indicated that aeration during fed-batch ethanol fermentation may improve the ethanol concentration in the final culture broth, as well as the ethanol productivity.     

Development of a low-cost fermentation medium for ethanol production from biomass

Nutrient cost is an important aspect in the fermentation of biomass to ethanol. With a goal of developing a cost-effective fermentation medium, several industrially available nutrient sources were evaluated for their effectiveness in the simultaneous saccharification and fermentation of pretreated poplar with Saccharomyces cerevisiae D₅A. These studies showed that a low-cost medium containing 0.3% corn steep liquor and 2.5 mM MgSO₄ · 7H₂O was similar in performance to a nutrient-rich medium. Besides its low cost, this alternative medium consists of components that are available on a commercial scale, thereby making it industrially relevant. Received: 14 August 1996 / Received revision: 7 January 1997 / Accepted: 24 January 1997