Tracking Construction Material over Space and Time: Prospective and Geo‐referenced Modeling of Building Stocks and Construction Material Flows

Construction material plays an increasingly important role in the environmental impacts of buildings. In order to investigate impacts of materials on a building level, we present a bottom‐up building stock model that uses three‐dimensional and geo‐referenced building data to determine volumetric information of material stocks in Swiss residential buildings. We used a probabilistic modeling approach to calculate future material flows for the individual buildings. We investigated six scenarios with different assumptions concerning per‐capita floor area, building stock turnover, and construction material. The Swiss building stock will undergo important structural changes by 2035. While this will lead to a reduced number in new constructions, material flows will increase. Total material inflow decreases by almost half while outflows double. In 2055, the total amount of material in‐ and outflows are almost equal, which represents an important opportunity to close construction material cycles. Total environmental impacts due to production and disposal of construction material remain relatively stable over time. The cumulated impact is slightly reduced for the wood‐based scenario. The scenario with more insulation material leads to slightly higher material‐related emissions. An increase in per‐capita floor area or material turnover will lead to a considerable increase in impacts. The new modeling approach overcomes the limitations of previous bottom‐up building models and allows for investigating building material flows and stocks in space and time. This supports the development of tailored strategies to reduce the material footprint and environmental impacts of buildings and settlements.     

Application of Markov Chain Model to Calculate the Average Number of Times of Use of a Material in Society. An Allocation Methodology for Open-Loop Recycling. Part 1: Methodology Development (7 pp)

- Preamble. In this series of two papers, a methodology to calculate the average number of times a material is used in a society from cradle to grave is presented and applied to allocation of environmental impact of virgin material. Part 1 focuses on methodology development and shows how the methodology works with hypothetical examples of material flows. Part 2 presents case studies for steel recycling in Japan, in which the methodology is applied and allocation of environmental impact of virgin steel is conducted. - Abstract Goal, Scope and Background. It has been recognized that LCA has a limitation in assessing open cycle recycling of materials because of inevitable subjective judgments in setting system boundary. According with the enforcement of recycling laws, there has been a rapid increase in recycling ratio of materials at the end-of-life of products in many industrialized countries. So, materials' life cycle is getting more complicated, which makes it difficult to quantify the environmental impacts of materials used in a product in an appropriate way. The purpose of this paper is to develop a methodology to calculate the average number of times a material is used in a society from cradle to grave. The method developed in this paper derives the average number of times material is used; this value could be used for allocation of environmental burdens of virgin material as well as an indicator for assessing the state of material use in a certain year, based on material flow of material in that year. Main Features Our methodology is based on Markov chain model using matrix-based numerical analysis. A major feature of this method is that it creates transition probability matrices for a material from the way in which the material is produced, consumed, and recycled, making it possible to simply elicit indicators that assess the status of material use in products in society. Our methodology could be an alternative method to derive the average number of times material is used, which could be used for allocation of environmental burdens of virgin material. Results and Discussions The methodology was applied to hypothetical examples of material flows, in which a virgin material was produced and used in products, recycled and finally landfilled. In some cases, closed loop and open loop recycling of materials existed. The transition probability matrix was created for each material flow, and how many times a virgin material is used in products until all of the elements are ultimately landfilled. Conclusions This methodology is applicable to a complicated material flow if the status of residence of a material and its flow in a society can be figured out. All the necessary data are the amount of virgin material production, amount of the material used in products, recycling rate of the material at the end of life of each product, the amount of scrap of the material that are used for products. In Part 2 of this paper, case studies for steel were conducted.     

Optimizing cardiac material parameters with a genetic algorithm

Determining the unknown material parameters of intact ventricular myocardium can be challenging due to highly nonlinear material behavior. Previous studies combining a gradient-search optimization procedure with finite element analysis (FEA) were limited to two-dimensional (2D) models or simplified three-dimensional (3D) geometries. Here we present a novel scheme to estimate unknown material parameters for ventricular myocardium by combining a genetic algorithm (GA) with nonlinear finite element analysis. This approach systematically explores the domain of the material parameters. The objective function to minimize was the error between simulated strain data and finite element model strains. The proposed scheme was validated for a 2D problem using a realistic material law for ventricular myocardium. Optimized material parameters were generally within 0.5% of the true values. To demonstrate the robustness of the new scheme, unknown material parameters were also determined for a realistic 3D heart model with an exponential hyperelastic material law. When using strains from two material points, the algorithm converged to parameters within 5% of the true values. We conclude that the proposed scheme is robust when estimating myocardial material parameters in 2D and 3D models.     

The sperm head of the plains mouse,Pseudomys australis: Ultrastructure and effects of chemical treatments

The ultrastructure of the sperm head of the plains mouse, Pseudomys australis, and the effects of chemical treatments on the sperm head components has been investigated to determine the nature of the material in the hooks on the apical margine of the sperm head. Ultrastructural studies indicated that the dorsal hook contained nuclear, subacrosomal, and acrosomal material, whereas the two ventral hooks were largely composed of an extention of the subacrosomal material with two thin acrosomal projections at their base. Acrosomal material was dispersed by mild detergent treatment, where as the bulk of the material in the ventral hooks were generally found to be similar to the subacrosomal material in the dorsal hook in their resistance to the various chemical treatments. Treatment of sperm with NaOH or guanidine-hydrochloride and DTT revealed two layers of material in the ventral hooks.     

Trabecular bone adaptation with an orthotropic material model.

Most bone adaptation algorithms, that attempt to explain the connection between bone morphology and loads, assume that bone is effectively isotropic. An isotropic material model can explain the bone density distribution, but not the structure and pattern of trabecular bone, which clearly has a mechanical significance. In this paper, an orthotropic material model is utilized to predict the proximal femur trabecular structure. Two hypotheses are combined to determine the local orientation and material properties of each element in the model. First, it is suggested that trabecular directions, which correspond to the orthotropic material axes, are determined locally by the maximal principal stress directions due to the multiple load cases (MLC) the femur is subject to. The second hypothesis is that material properties in each material direction can be determined using directional stimuli, thus extending existing adaptation algorithms to include directionality. An algorithm is utilized, where each iteration comprises of two stages. First, material axes are rotated to the direction of the largest principal stress that occurs from a multiple load scheme applied to the proximal femur. Next, material properties are modified in each material direction, according to a directional stimulus. Results show that local material directions correspond with known trabecular patterns, reproducing all main groups of trabeculae very well. The local directional stiffnesses, degree of anisotropy and density distribution are shown to conform to real femur morphology.     

Material Flow Accounts and Driving Factors of Economic Growth in the Philippines

This study looks into material flow trends in the Philippines from 1985 to 2010 by utilizing the methodology of economy‐wide material flow analysis. Using domestic data sources, this study presents disaggregated annual material flow trends in terms of four major material categories, namely: biomass; fossil energy carriers; ores and industrial minerals; and construction minerals. The results describe in detail the growth of material flows in a high‐density country at the onset of its development and reveal the shift of material consumption from dominance of renewable materials in 1985 to nonrenewable materials in 2010. IPAT analysis shows that the increase in material consumption was driven by population growth from 1985 to 1998 and by growth in affluence from 1999 to 2010. However, high inequalities amidst the growing economy suggest that a small group of wealthy people have influenced the acceleration of material consumption in the Philippines. The results of this research are intended to provide a thorough analysis of the processes occurring in Philippine economic growth in order to assist in tackling implications for the important issue of sustainable resource management.     

Estimation of Life Cycle Material Costs of Cadmium Telluride– and Copper Indium Gallium Diselenide–Photovoltaic Absorber Materials based on Life Cycle Material Flows

Chalcogenide and chalcopyrite photovoltaic (PV) technologies are highly suitable for solar energy conversion because of their high efficiency, long‐term stable performance, and low‐cost production. However, the absorber materials that are used, such as indium, gallium, and tellurium, are regarded as critical, and their limited availability can hinder market expansion. Therefore, we assess how material efficiency measures along the PV module's life cycle can reduce the net material demand of the absorber materials and thus the material costs. In order to estimate the material flows, we developed a closed‐loop model for the life cycle representing the phases module production, module collection, module recycling, and refinement. In order to reflect the variety and uncertainty in each phase, we compose three different efficiency scenarios by varying material efficiency measures on process and product levels. For each scenario, we compute the life cycle material costs based on the computed material flows. The results show that, in the long term, the material demand can be reduced down to one fourth of the required feedstock for module manufacturing; that is, three fourths of the absorber material stays in the life cycle in a very efficient scenario. Thus, total material costs along the life cycle could be significantly reduced, because the costs for material recycling are lower than the costs for “new” technical‐grade material. This reduction in life cycle material costs means that cadmium telluride– and copper indium gallium diselenide–PV can still be financially viable even if the price of the absorber materials increases significantly. Hence those technologies will still be competitive against crystalline silicon PV in the mid to long term.     

The nonlinear material properties of liver tissue determined from no-slip uniaxial compression experiments

The mechanical response of soft tissue is commonly characterized from unconfined uniaxial compression experiments on cylindrical samples. However, friction between the sample and the compression platens is inevitable and hard to quantify. One alternative is to adhere the sample to the platens, which leads to a known no-slip boundary condition, but the resulting nonuniform state of stress in the sample makes it difficult to determine its material parameters. This paper presents an approach to extract the nonlinear material properties of soft tissue (such as liver) directly from no-slip experiments using a set of computationally determined correction factors. We assume that liver tissue is an isotropic, incompressible hyperelastic material characterized by the exponential form of strain energy function. The proposed approach is applied to data from experiments on bovine liver tissue. Results show that the apparent material properties, i.e., those determined from no-slip experiments ignoring the no-slip conditions, can differ from the true material properties by as much as 50% for the exponential material model. The proposed correction approach allows one to determine the true material parameters directly from no-slip experiments and can be easily extended to other forms of hyperelastic material models.     

A facile preparation of gel materials from a solution of cellulose in ionic liquid

This paper reports a facile preparation of a flexible gel material from a solution of cellulose (15% w/w) in an ionic liquid of 1-butyl-3-methylimidazolium chloride by keeping it at room temperature for 7 days. Elemental analysis data indicated that the obtained gel material was composed of cellulose, the ionic liquid, and water. Both XRD and TGA results suggested that crystalline structure of cellulose was largely disrupted in the material. However, the existence of non-crystalline aggregates was assumed by the XRD data of the material. The gel material was probably obtained by the formation of cellulose aggregates in the solution, attributed to the gradual absorption of water. When the material was heated at 120 degrees C, it became soft, and converted into a fluid at 150 degrees C. By keeping the soft material at room temperature for 2 days, a gel material was regenerated, which was more transparent compared with the original material.     

A Seated Burial and Associated Boatstone from Northwestern Kansas

Abstract

The skeletal remains of an adult male individual from the 14TO301 site was analyzed to the extent allowed by the condition of the bony skeleton. In addition to the skeleton, one cultural object, a boatstone, is described and utilized in order to provide a rough date for the skeletal material. The cultural material is identified as Woodland and is compared w1th other Woodland material in the region. The results of the skeletal analysis compare favorably with other single male variables in the same or near region of roughly the same time period. The material also however, corresponds favorably with earlier archaic material from Colorado. The analysis of the skeletal and cultural material expands our knowledge of the distribution of the Woodland period in the high plains. Non-metric analysis is included in the analysis of the skeletal material.     

Galloylglucoses of low molecular weight as mordant in electron microscopy. I. Procedure, and evidence for mordanting effect

Coated vesicles (CVs), plain synaptic vesicles (PSVs), and nonvesicular flocculent material were isolated from synaptosomes and examined with goniometry and high-resolution electron microscopy after either negative staining or various biochemical procedures. The flocculent material (i.e. the presynaptic matrix material except CV shells) is largely composed of particulate or elongated (chainlike) structures; some of this material (here referred to as particle/chain material) is attached to PSVs. The results obtained were: (a) the proteinaceous properties of the CV coat (also referred to as CV shell) and the particle/chain material were demonstrated with chymotrypsin; (b) the CV shell, studied with various negative-staining techniques, differs from the particle/chain material since it has no 3-4-nm globular subunits and reacts differently to alkaline pH; (c) the particle/chain material consists of aggregates of 3-4-nm globular subunits, four of which yield 8-10-nm fine particles; and these particles can be further aggregated into chains 8-10 nm wide and up to 30-60 nm long showing a "hollow" core; (d) vinblastine sulfate induced ringlike or helical crystalloid precipitates closely resembling the vinblastine-induced microtubule crystals reported in the literature, but vinblastine had no effect on either the CV shell material or the particle/chain material.     

Finite element modeling of impulsive excitation and shear wave propagation in an incompressible,transversely isotropic medium

Elastic properties of materials can be measured by observing shear wave propagation following localized, impulsive excitations and relating the propagation velocity to a model of the material. However, characterization of anisotropic materials is difficult because of the number of elasticity constants in the material model and the complex dependence of propagation velocity relative to the excitation axis, material symmetries, and propagation directions. In this study, we develop a model of wave propagation following impulsive excitation in an incompressible, transversely isotropic (TI) material such as muscle. Wave motion is described in terms of three propagation modes identified by their polarization relative to the material symmetry axis and propagation direction. Phase velocities for these propagation modes are expressed in terms of five elasticity constants needed to describe a general TI material, and also in terms of three constants after the application of two constraints that hold in the limit of an incompressible material. Group propagation velocities are derived from the phase velocities to describe the propagation of wave packets away from the excitation region following localized excitation. The theoretical model is compared to the results of finite element (FE) simulations performed using a nearly incompressible material model with the five elasticity constants chosen to preserve the essential properties of the material in the incompressible limit. Propagation velocities calculated from the FE displacement data show complex structure that agrees quantitatively with the theoretical model and demonstrates the possibility of measuring all three elasticity constants needed to characterize an incompressible, TI material.     

StrainInfo introduces electronic passports for microorganisms

Microbiology builds upon biological material deposited in biological resource centers (BRCs) as a reference framework for collaborative research. BRCs assign so-called strain numbers to label the deposited material and are responsible for long-term preservation and worldwide distribution of the material. Cultured microorganisms can be deposited into multiple BRCs and BRCs also mutually exchange their holdings. As a result, many different strain numbers can be attached to biological material that stems from the same isolate. In practice, this material is considered equivalent and used interchangeably. This implies that finding information on given biological material requires all equivalent strain numbers to be used when searching.     

Web-based education in bioprocess engineering

The combination of web technology, knowledge of bioprocess engineering, and theories on learning and instruction might yield innovative learning material for bioprocess engineering. In this article, an overview of the characteristics of web-based learning material is given, as well as guidelines for the design of learning material from theories of learning and instruction and from the bioprocess engineering domain. A diverse body of learning material is presented, which illustrates the application of these guidelines; this material has been developed during the past six years for different courses, mostly at undergraduate level, and it illustrates how web-based learning material can enable various different approaches to learning objectives that might improve overall learning. Such learning material has been used for several years in education, it has been evaluated with positive results, and is now part of the regular learning material for bioprocess engineering at Wageningen University.     

基于物质流分析方法的生态海岛建设研究——以长海县为例

建设生态海岛是海岛生态经济系统实现可持续发展的重要途径。运用物质流分析方法对长海县的物质输入与输出状况进行计算,并用物质消耗强度、废物排放强度和环境负荷强度3个指标衡量了该海岛县生态效率的变化,分析了技术进步对海岛生态经济系统生态压力变化的贡献状况。结果表明,2003—2009年间,长海县物质输入总量、物质输出总量和环境负荷总量呈增长态势;生态效率明显提高;技术进步对减轻海岛生态经济系统生态压力的贡献没有抵消经济增长所产生的生态压力的增加量。为了减少物质输入和废物输出,减轻经济活动对海岛生态系统产生的压力,建立创新型管理机制有效促进技术进步,不断提高生态效率具有特别重要的作用。     

区域生态经济系统的物质输入与输出分析——以常州市武进区为例

运用物质流分析（MFA）方法,对江苏省常州市武进区生态经济系统中物质输入与输出进行了系统的分析,结果表明：（1）随着社会经济发展和人口增长,武进区物质输入总量及人均物质输入量也在增加,但递增速率均远小于GDP增长速率,而物质输出总量及人均物质输出量则呈现递减趋势;（2）在不考虑水的因素情况下,武进区物质输入量保持较快的上升速度,其中固体物质的增长速率远远大于气体物质的增长速率;物质输出量则呈总体下降趋势,其中以气体物质输出量的贡献最大,对环境造成污染的物质以气体特别是以化石燃料燃烧排放的废气和工业废气为主;（3）排除占大部分比例农业用水的上升,工业用水、城镇生活用水和地下水总量及人均利用强度都在减少;同时,总的废水排放量及人均排放量在减少,其中又以生活废水排放量的减少最快,其次是工业废水;（4）单位GDP物质输入量的变化处于波动状态,同期的单位GDP物质输出量则呈递减趋势,单位GDP用水量和单位GDP废水排放量则有相同的递减趋势,表征了武进区资源利用效率的稳步提高,区域经济增长和环境压力也在逐步脱钩。上述结果体现了武进区近年来循环经济发展模式的优势,但还存在较多问题,说明武进区在调整物质利用强度和提高资源利用效率方面还需下更大的功夫,并采取相关措施,以期提高实施循环经济战略与建设节约型社会的地位和意义。文章最后结合研究区实际情况就区域环境一经济的协调发展进行了展望,指出了物质流分析方法在应用中的一些缺陷,为今后该领域的进一步研究提供了借鉴。     

Static indentation of anisotropic biomaterials using axially asymmetric indenters--a computational study

Indentation has historically been used by biomechanicians to extract the small strain elastic or viscoelastic properties of biological tissues. Because of the axisymmetry of indenters used in these studies however, analysis of the results requires the assumption of material isotropy and often yields an "effective" elastic modulus. Since most biological tissues such as bone and myocardium are known to be anisotropic, the use of conventional indentation techniques for estimating material properties is therefore limited. The feasibility of using an axially asymmetric indenter to determine material directions and in-plane material properties for anisotropic tissue is explored here using finite element analysis. The load versus displacement curves as would be measured by an indenter depend on the orientation of the indenter cross section relative to the in-plane material axes, thus suggesting a method for determining the underlying material directions. Additionally, the stiffness of the tissue response to indentation is sensitive to the values of the in-plane anisotropic material properties and prestretches, and thus test results can be used to back out relevant constitutive parameters.     

A Probabilistic Dynamic Material Flow Analysis Model for Chinese Urban Housing Stock

The stock‐driven dynamic material flow analysis (MFA) model is one of the prevalent tools to investigate the evolution and related material metabolism of the building stock. There exists substantial uncertainty inherent to input parameters of the stock‐driven dynamic building stock MFA model, which has not been comprehensively evaluated yet. In this study, a probabilistic, stock‐driven dynamic MFA model is established and China's urban housing stock is selected as the empirical case. This probabilistic dynamic MFA model has the ability to depict the future evolution pathway of China's housing stock and capture uncertainties in its material stock, inflow, and outflow. By means of probabilistic methods, a detailed and transparent estimation of China's housing stock and its material metabolism behavior is presented. Under a scenario with a saturation level of the population, urbanization, and living space, the median value of the urban housing stock area, newly completed area, and demolished area would peak at around 49, 2.2, and 2.2 billion square meters, respectively. The corresponding material stock and flows are 79, 3.5, and 3.3 billion tonnes, respectively. Uncertainties regarding housing stock and its material stock and flows are non‐negligible. Relative uncertainties of the material stock and flows are above 50%. The uncertainty importance analysis demonstrates that the material intensity and the total population are major contributions to the uncertainty. Policy makers in the housing sector should consider the material efficiency as an essential policy to mitigate material flows of the urban building stock and to lower the risk of policy failures.     

Coastal connectivity and spatial subsidy from a microbial perspective

The transfer of organic material from one coastal environment to another can increase production in recipient habitats in a process known as spatial subsidy. Microorganisms drive the generation, transformation, and uptake of organic material in shallow coastal environments, but their significance in connecting coastal habitats through spatial subsidies has received limited attention. We address this by presenting a conceptual model of coastal connectivity that focuses on the flow of microbially mediated organic material in key coastal habitats. Our model suggests that it is not the difference in generation rates of organic material between coastal habitats but the amount of organic material assimilated into microbial biomass and respiration that determines the amount of material that can be exported from one coastal environment to another. Further, the flow of organic material across coastal habitats is sensitive to environmental change as this can alter microbial remineralization and respiration rates. Our model highlights microorganisms as an integral part of coastal connectivity and emphasizes the importance of including a microbial perspective in coastal connectivity studies.     

Concomitant changes of ACTH, β-endorphin and N-terminal portion of pro-opiomelanocortin in rats

Radioimmunoassay developed to measure N-terminal peptide of pro-opiomelanocortin isolated from porcine pituitaries was used to measure changes in the concentration of immunoreactive material in rat plasma. The N-terminal peptide immunoreactive material decreased in plasma after hypophysectomy of both female and male rats below the level of detectability and substantially increased after adrenalectomy as compared to normal control rats. The same changes were observed when β-endorphin and ACTH like immunoreactive material was measured. The primary culture of rat anterior pituitary cells released ACTH and N-terminal peptide-like immunoreactive material into the incubation medium. The results seem to indicate that the N-terminal immunoreactive material is a secretory product produced by the pituitary gland.