Application of bioreactors for large-scale micropropagation systems of plants

Summary The application of bioreactor culture techniques for plant micropropagation is regarded as one of the ways to reduce production cost by scaling-up and automation. Recent experiments are restricted to a small number of species that, however, demonstrate the feasibility of this technology. Periodic immersion liquid culture using ebb and flood system and column-type bubble bioreactors equipped with a raft support system to maintain plant tissues at the air and liquid interface were found to be suitable for micropropagation of plants via the organogenic pathway. Balloon-type bubble bioreactors proved to be fit for micropropagation via somatic embryogenesis with less shear stress on cultured cells. Several cultivars of Lilium were successfully propagated using a two-stage culture method in one bioreactor. A large number of small-scale segments were cultured for 4 wk with periodic immersion liquid culture to induce multiple bulblets from each segment, then the bulblet induction medium was changed into bulblet growth medium by employing a submerged liquid bioreactor system. This culture method resulted in a nearly 10-fold increase in bulblet growth compared to conventional culture with solid medium. About 20 000 cuttings of virus-free potato could be obtained from 120 singlenode explants in a 20-liter balloon-type bubble bioreactor after 8 wk of culture. The percentage of ex vitro survival and root induction of the cuttings was more than 95%. Other successful results were obtained from the micropropagation and transplant production of chrysanthemum, sweetpotato, Chinese foxglove. Propagation systems via somatic embryogenesis in Acanthopanax koreanum and thornless Aralia elata were established using a liquid suspension of embryogenic determined cells. More than 500 000 somatic embryos in different stages were harvested from a 10-liter balloon-type bubble bioreactor after a 6-wk culture. Further development of these embryos in solid medium and eventually in the field was successful. The bioreactor system could reduce initial and operational cost for micropropagation, but further development of sophisticated technology might be needed to apply this system to plant micropropagation industries.     

Improvement of plastic-based disposable bioreactors for plant science needs

The present article describes two new applications of plastic-based cell culture systems in the plant biotechnology domain. Different types of bioreactors are used at Nestlé R&D Center-Tours for large scale culture of plants cells to produce metabolites or recombinant proteins and for mass propagation of selected plant varieties by somatic embryogenesis. Particularly, recent studies are directed to cut down the production costs of these two processes by developing disposable cell culture systems. For large scale culture, two novel flexible plastic-based disposable bioreactors have been developed from 10 to 100 l working volumes, validated with several plant species (“Wave and Undertow” and “Slug Bubble” bioreactors). Vegetative propagation of elite plant varieties is achieved through somatic embryogenesis in liquid medium. A pilot scale process has been recently set up for the industrial propagation of Coffea canephora (Robusta coffee). The current production capacity is 2.5–3.0 million embryos per year. The pre-germination of the embryos was previously conducted by temporary immersion in liquid medium in 10-l glass bioreactors. An improved process has been developed using a 10-l disposable bioreactor consisting in a bag containing a rigid plastic box (“Box-in-Bag” bioreactor), insuring, amongst other advantages, a higher light transmittance to the biomass due to its horizontal design.     

Temporary immersion systems in plant micropropagation

Temporary immersion systems for plant micropropagation have been described and grouped into 4 categories according to operation: tilting and rocker machines; complete immersion of plant material and renewal of the nutrient medium; partial immersion and a liquid nutrient renewal mechanism; complete immersion by pneumatic driven transfer of liquid medium and without nutrient medium renewal. The positive effects of temporary immersion on micropropagation are indicated for shoot proliferation and microcuttings, microtuberization and somatic embryogenesis. Immersion time, i.e. duration or frequency, is the most decisive parameter for system efficiency. Optimizing the volume of nutrient medium and the volume of the culture container also substantially improves efficacy, especially for shoot proliferation. Temporary immersion also generally improves plant material quality. It results in increased shoot vigour and in the frequency of morphologically normal somatic embryos. Hyperhydricity, which seriously affects cultures in liquid medium, can be eliminated with these culture systems or controlled by adjusting the immersion times. Plant material propagated by temporary immersion can perform better during the acclimatization phase than material obtained on semi-solid or in liquid media. Successful regeneration of plants, after direct sowing on soil of Solanum tuberosum microtubers and Coffea arabica somatic embryos produced in temporary immersion bioreactors, has been demonstrated. As could be expected when using liquid medium for micropropagation, several estimations confirm large gains in efficacy from temporary immersion. The parameters most involved in reducing production costs include: (1) the drastic reduction in work; (2) reduction in shelving area; (3) reduction in the number of containers used; (4) better biological yields. Scaling-up somatic embryogenesis and shoot proliferation procedures involving temporary immersion systems in order to commercialize this process are now taking place.     

Application of bioreactor systems for large scale production of horticultural and medicinal plants

Automation of micropropagation via organogenesis or somatic embryogenesis in a bioreactor has been advanced as a possible way of reducing costs. Micropropagation by conventional techniques is typically a labour-intensive means of clonal propagation. The paper describes lower cost and less labour-intensive clonal propagation through the use of modified air-lift, bubble column, bioreactors (a balloon-type bubble bioreactor), together with temporary immersion systems for the propagation of shoots, bud-clusters and somatic embryos. Propagation of Anoectochilus, apple, Chrysanthemum, garlic, ginseng, grape, Lilium, Phalaenopsis and potato is described. In this chapter, features of bioreactors and bioreactor process design specifically for automated mass propagation of several plant crops are described, and recent research aimed at maximizing automation of the bioreactor production process is highlighted.     

Somatic embryogenesis and plant regeneration in elite genotypes of Picea koraiensis

Picea koraiensis, called Korean spruce, is an evergreen tree and found mostly in northeast Asia. In this study, plant regeneration via somatic embryogenesis from open-pollinated immature zygotic embryos of nine genotypes of elite trees was established. Immature zygotic embryos were cultured onto RJW medium modified from 505 medium with 21.48 μM NAA, 2.22 μM BA, and 2.32 μM KT. The average frequency for all nine genotypes was 74.2%. Embryogenic calluses of the nine genotypes of elite trees were subcultured on RJW basal medium containing 8.06 μM NAA, 1.11 μM BA, and 1.16 μM kinetin. The calluses of three lines, 3^#, 9^#, and 2^#, were actively proliferated but others were not. Somatic embryogenesis was induced from the embryogenic callus in genotypes of 3^#, 9^#, and 2^# on RJW medium with ABA and 60 g l⁻¹ sucrose. Cotyledonary somatic embryos were subjected to a drying process. The drying of embryos by uncapping the culture bottle for 5 days on a clean bench resulted in a high frequency of germination of somatic embryos (87% in RJW medium). However, plantlet conversion from germinated embryos was greatly reduced and the optimal medium for plant conversion was 1/2 WPM or 1/2 BMI medium. In conclusion, we have, for the first time, established a plant regeneration system via somatic embryogenesis in the Korean spruce, which can be applied for rapid micropropagation of elite trees.     

Simple bioreactors for mass propagation of plants

Bioreactors provide a rapid and efficient plant propagation system for many agricultural and forestry species, utilizing liquid media to avoid intensive manual handling. Large-scale liquid cultures have been used for micropropagation through organogenesis or somatic embryogenesis pathways. Various types of bioreactors with gas-sparged mixing are suitable for the production of clusters of buds, meristems or protocorms. A simple glass bubble-column bioreactor for the proliferation of ornamental and vegetable crop species resulted in biomass increase of 3 to 6-fold in 3–4 weeks. An internal loop bioreactor was used for asparagus, celery and cucumber embryogenic cultures. However, as the biomass increased, the mixing and circulation were not optimal and growth was reduced. A disposable pre-sterilized plastic bioreactor (2–5-l volume) was used for the proliferation of meristematic clusters of several ornamental, vegetable and woody plant species. The plastic bioreactor induced minimal shearing and foaming, resulting in an increase in biomass as compared to the glass bubble-column bioreactor. A major issue related to the use of liquid media in bioreactors is hyperhydricity, that is, morphogenic malformation. Liquid cultures impose stress signals that are expressed in developmental aberrations. Submerged tissues exhibit oxidative stress, with elevated concentrations of reactive oxygen species associated with a change in antioxidant enzyme activity. These changes affect the anatomy and physiology of the plants and their survival. Malformation was controlled by adding growth retardants to decrease rapid proliferation. Growth retardants ancymidol or paclobutrazol reduced water uptake during cell proliferation, decreased vacuolation and intercellular spaces, shortened the stems and inhibited leaf expansion, inducing the formation of clusters. Using a two-stage bioreactor process, the medium was changed in the second stage to a medium lacking growth retardants to induce development of the meristematic clusters into buds or somatic embryos. Cluster biomass increased 10–15-fold during a period of 25–30 days depending on the species. Potato bud clusters cultured in 1.5 1 of medium in a 2-l capacity bioreactor, increased during 10–30 days. Poplar in vitro roots regenerated buds in the presence of thidiazuron (TDZ); the biomass increased 12-fold in 30 days. Bioreactor-regenerated clusters were separated with a manual cutter, producing small propagule units that formed shoots and initiated roots. Clusters of buds or meristematic nodules with reduced shoots, as well as arrested leaf growth, had less distortion and were optimal for automated cutting and dispensing. In tuber-, bulb- and corm-producing plants, growth retardants and elevated sucrose concentrations in the media were found to enhance storage organ formation, providing a better propagule for transplanting or storage. Bioreactor-cultures have several advantages compared with agar-based cultures, with a better control of the contact of the plant tissue with the culture medium, and optimal nutrient and growth regulator supply, as well as aeration and medium circulation, the filtration of the medium and the scaling-up of the cultures. Micropropagation in bioreactors for optimal plant production will depend on a better understanding of plant responses to signals from the microenvironment and on specific culture manipulation to control the morphogenesis of plants in liquid cultures.     

Possible effect from shear stress on maturation of somatic embryos of Norway spruce (Picea abies)

Somatic embryogenesis is the only method with the potential for industrial scale clonal propagation of conifers. Implementation of the method has so far been hampered by the extensive manual labor required for development of the somatic embryos into plants. The utilization of bioreactors is limited since the somatic embryos will not mature and germinate under liquid culture conditions. The negative effect on mature embryo yields from liquid culture conditions has been previously described. We have described the negative effects of shear stress on the development of early stage somatic embryos (proembryogenic masses; PEMs) at shear stresses of 0.086 and 0.14 N/m². In the present study, additional flow rates were studied to determine the effects of shear stress at lower rates resembling shear stress in a suspension culture flask. The results showed that shear stress at 0.009, 0.014, and 0.029 N/m² inhibited the PEM expansions comparing with the control group without shear stress. This study also provides validation for the cross‐correlation method previously developed to show the effect of shear stress on early stage embryo suspensor cell formation and polarization. Furthermore, shear stress was shown to positively affect the uptake of water into the cells. The results indicate that the plasmolyzing effect from macromolecules added to liquid culture medium to stimulate maturation of the embryos are affected by liquid culture conditions and thus can affect the conversion of PEMs into mature somatic embryos. Bioeng. 2011; 108:1089–1099. © 2010 Wiley Periodicals, Inc.     

Proliferation,maturation and germination of Castanea sativa Mill. Somatic embryos originated from leaf explants

Experiments were performed to determine the influence of proliferation medium on the maintenance of embryogenic competence and on repetitive embryogenesis in Castanea sativa Mill. somatic embryos derived from leaf explants. Somatic embryo proliferation was carried out by both direct secondary embryogenesis and by the culture of nodular callus tissue originated from cotyledons of somatic embryos. Both systems led to the production of cotyledonary somatic embryos on Murashige and Skoog proliferation medium supplemented with 0.1 mg l-1 benzyladenine and 0.1 mg l-1 naphthaleneacetic acid. Carbon source and concentration had a marked influence on maturation and subsequent germination ability of chestnut somatic embryos. Plantlet conversion was achieved in embryos matured on media with 6 % sucrose, and on 3 or 6 % maltose, whereas mean shoot length, root length and leaf number of produced plants were not significantly affected by these maturation media. Overall, the best results were obtained with 3 % maltose-matured somatic embryos, giving rise to 6 % plant recovery in addition to 33 % of embryos exhibiting only shoot development. The application of a 2-month cold treatment at 4 degrees C to somatic embryos matured on medium with 3 % maltose was necessary for achieving plant conversion, while partial desiccation did not appear to influence this response. A total of 39 % of embryos eventually produced plants either through conversion to plantlets or indirectly through rooting of shoots. Shoots formed by somatic embryos could be excised, multiplied and rooted following the micropropagation procedures previously developed for chestnut.     

Somatic embryogenesis of the banana hybrid cultivar FHIA-18 (AAAB) in liquid medium and scaled-up in a bioreactor

The development of somatic embryos in liquid culture medium has a number of advantages for large-scale propagation of plants. This paper describes an improved system for the mass propagation via somatic embryogenesis of the banana hybrid cultivar FHIA-18 (AAAB). Explants from immature male flowers were used to form high frequency embryogenic tissue, this tissue was then used to establish embryogenic cell suspensions in a basic MS medium plus 1.0 mg l^–1 biotin, 100 mg l^–1 glutamine, 100 mg l^–1 malt extract (Sigma), 1.0 mg l^–1 2,4-D and 45 g l^–1 sucrose. Secondary multiplication of somatic embryos was achieved in liquid media in rotary shaker and in bioreactors. The number of embryos per litre obtained with 80.0% DO₂ and effects of pH were also studied. A high regeneration percentage of plants were obtained (89.3%) in only 1 month of culture, somatic embryos were then placed to germinate in temporary immersion systems and field testing of somaclonal variation.     

酿酒葡萄"梅尔诺"再生系统建立的研究

以酿酒葡萄“梅尔诺”离体胚珠、叶柄为材料．通过控制激素水平、光照和温度等,对建立再生体系的器官发生途径和体胚发生途径进行了研究。结果表明,体胚的诱导和不定芽的再生与基本培养基、叶柄的着生部位、生长调节物质种类和浓度等因素有关。由“梅尔诺”的胚珠愈伤组织再生出体细胞胚的最佳培养基配方为CPSE培养基(CP287 BA 0．2mg／L NOA 1．0mg／L),体细胞胚再生率可达47．50％。“梅尔诺”体细胞胚在CPSE培养基上100％萌发为芽状,将其切断置于培养基MS TDZ 4．0mg／L上可直接诱导出绿色不定芽,再生率为52．25％;同时在培养基MS TDZ2．0mg／L上获得了“梅尔诺”离体叶柄再生不定芽．再生率为62．42％．二者再生的不定芽的最他增殖培养基为MS BA0．5mg／L。“梅尔诺”体细胞胚的萌发芽在WPM培养基中能很好的生根及成苗,并建立了单芽茎段微繁体系。     

Scaled-up proliferation and regeneration of Nerine in liquid cultures Part I. The induction and maintenance of proliferating meristematic clusters by paclobutrazol in bioreactors

The natural propagation rate of bulb forming Amaryllidaceae including Nerine is low. Conventional micropropagation techniques are labor intensive and therefore expensive. Liquid cultures facilitate: scaling up, automation and cost reduction of micropropagation. Inflorescence-derived explants of Nerine were cultured on 2,4-dichlorophenoxyacetic acid (2,4-d) and 6-benzyladenine (BA) supplemented Murashige & Skoog (MS) medium. Callus-like tissue interspersed with nodular tissue, as well as direct organogenesis developed at the junction between flower pedicel and peduncle. Subculture of nodular tissue to 1-naphthalene acetic acid (NAA), BA and paclobutrazol (PAC) supplemented liquid medium in Erlenmeyer flasks or bubble bioreactors resulted in proliferation of rounded, compact, easily crumbled meristematic clusters. Growth and proliferation in bioreactors were higher than in shaken flasks and were affected differently by the inoculum to medium ratio in the two types of culture vessel. Nerine cultures showed low sensitivity to high aeration rates in bubble bioreactors despite the accumulation of debris. It was therefore possible to increase aeration rates without reducing the proliferation rate or damaging the quality of the meristematic aggregates. The conditions in semi-continuous culture in flasks and bioreactors were more favorable and increased the growth value by 100% and 140%, respectively. The total protein content increased by 180% in flasks and 90% in bioreactors. Although the presence of PAC throughout the culture period decreased growth and proliferation, it was a promotive bioregulator for meristernatic cluster formation. Proembryogenic clusters developed upon the removal of PAC. The use of meristematic clusters for micropropagation in scaled-up liquid cultures is discussed.     

Regeneration of somatic embryos in Theobroma cacao L. in temporary immersion bioreactor and analyses of free amino acids in different tissues

The present study aimed at developing temporary immersion bioreactor techniques for multiplication of cacao somatic embryos. Temporary Immersion System (TIS), i.e. flooding of plant tissue at regular time intervals provides an efficient way to propagate plants. Somatic embryos were regenerated in twin flask bioreactors. The TIS proved to be suitable for mass regeneration of somatic embryos and for their subsequent direct sowing. The number of embryos after 3 months of culture was significantly higher in TIS cultures than in the solid medium variant. TIS also improved embryo development regarding the conversion to torpedo shaped forms. Matured embryos derived from TIS and pre-treated with 6% sucrose were converted into plants after direct sowing. Additionally to the influence of culture conditions on the development of somatic embryogenesis the content and composition of free amino acids were analysed. The content of free amino acids in somatic embryos rose as immersion frequency increased. The endogenous free GABA content in embryogenic callus was significantly higher than in non-embryogenic callus.     

Micropropagation of Elaeis guineensis Jacq. 'Dura': Comparison of three basal media for efficient regeneration

Three basal plant tissue culture media, namely, N6, MS, and modified Y3, were compared to optimize micropropagation protocol for E. guineensis. Full strength media were used separately to regenerate plantlets directly using immature zygotic embryos (IZEs), and through somatic embryogenesis of calli obtained from IZEs. The plantlets regenerated by direct regeneration on three media were examined for shoot length and rooting percentage. For the induction of callus, somatic embryogenesis, and rooting modified Y3 medium was the most effective. In conclusion, the results indicate that modified Y3 medium is the most suitable for direct regeneration, callus induction and somatic embryogenesis in E. guineensis.     

In vitro propagation of <Emphasis Type="Italic">Hippeastrum</Emphasis> × <Emphasis Type="Italic">chmielii</Emphasis> Chm. – influence of flurprimidol and the culture in solid or liquid medium and in temporary immersion systems

At Weyerhaeuser Company, somatic embryo production in liquid medium and manufactured seed delivery has been developed to reduce labor costs and increase efficiency of mass clonal propagation. We have scaled-up embryonal suspensor masses (ESM) of Douglas-fir in 1-l liquid medium flasks. Over 10,000 somatic embryos have been produced from a single flask. We have cryostored ESM of over 700 genotypes in liquid nitrogen. Somatic embryos of Douglas-fir have also been produced from liquid medium in a bioreactor. Different types of bioreactors are required for embryo multiplication and for cotyledonary embryo development. Over 250,000 Douglas-fir somatic seedlings from a large number of genotypes have been produced for clonal field tests.     

Somatic embryo formation and germination from immature embryo-derived suspension-cultured cells of Angelica sinensis (Oliv.) Diels

Embryogenic callus was induced from immature embryos of Angelica sinensis cultured on Murashige and Skoog (MS) basal medium. Embryogenic callus growth was more rapid on MS basal medium than on B5 or White medium. Embryogenic callus was used to establish a suspension culture and somatic embryos and germinating embryos developed during the culture. A shaking speed of 80 rpm was found to be optimal for establishing suspension cultures, while 100 rpm produced more somatic embryos and germinating embryos with an initiation cell density of 0.2 ml packed cell volume/25 ml medium. Adding 0.3% agar to the liquid medium also stimulated the formation of somatic and germinating embryos. While no plant growth regulators were needed for culture initiation and plant regeneration, the addition of 0.5–1 mg/l 2,4-dichlorophenoxyacetic acid was needed to maintain the embryogenic suspension culture by preventing embryo germination. Forty percent of the germinating embryos survived after culturing on filter paper moistened with liquid half-strength MS medium containing 3% sucrose. The plants were successfully transferred into soil. Received: 19 March 1997 / Revision received: 21 November 1997 / Accepted: 19 January 1998     

The use of somatic embryogenesis for plant propagation in cassava

In cassava, somatic embryogenesis starts with the culture of leaf explants on solid Murashige and Skoog-based medium supplemented with auxins. Mature somatic embryos are formed within 6 wk. The cotyledons of the primary somatic embryos are used as explants for a new cycle of somatic embryogenesis. The cotyledons undergo secondary somatic embryogenesis on both liquid and solid Murashige and Skoog-based medium supplemented with auxins. Depending on the auxin, new somatic embryos are formed after 14–30 d after which they can be used for a new cycle of somatic embryogenesis. In liquid medium, more than 20 secondary somatic embryos are formed per initial cultured embryo. In both primary and secondary somatic embryogenesis, the somatic embryos originate directly from the explants. Transfer of clumps of somatic embryos to a Greshoff and Doy-based medium supplemented with auxins results in indirect somatic embryogenesis. The direct form of somatic embryogenesis has a high potential for use in plant propagation, whereas the indirect has a high potential for use in genetic modification of cassava. Mature somatic embryos germinate into plants after desiccation and culture on a Murashige and Skoog-based medium supplemented with benzylaminopurine (BA). Depending on the used BA concentration, plants can either be transferred either directly to the greenhouse or after using standard multiplication protocols.     

The morphological variability within a population of coffee somatic embryos produced in a bioreactor affects the regeneration and the development of plants in the nursery

A 1-liter bioreactor was used to obtain approximatively 800 Coffea arabica somatic embryos, 86% of which reached the `germinated' stage but with morphological heterogeneity. The population was sub-divided into three categories according to cotyledon area: 'small', 'medium' and 'large', that amounted to 32%, 36% and 4.5%, respectively. The effect of embryo morphology on plantlet conversion after direct sowing in soil and on plant development in the nursery was investigated. Somatic embryos with large cotyledons had only a 25% plantlet conversion rate, whereas somatic embryos with small to medium-sized cotyledons had conversion rates of 47% and 63%, respectively. The vigour of the aerial and root systems of regenerated plantlets at the end of the plant conversion stage was also affected as the embryos with small, medium and large cotyledon mostly regenerated small plantlets (0.5–1.5 cm), medium plantlets (1.5–2.5 cm) and large plantlets (2.5–5 cm), respectively. When transplanted in plastic bags, these 3 populations of plantlets exhibited distinct development rates. They had an initial slow growth phase, which was much longer for the small plantlets, followed by a rapid growth phase. After 40 weeks in the nursery, an analysis of the growth parameters of aerial and radical systems showed that the vigour of the plants was strongly related to the vigour of the plantlets transplanted. The heterogeneity of somatic embryos in the bioreactor affected both the plant conversion efficiency in soil and the plant growth in nursery, where it mainly resulted in retarded growth, primarily in plantlets derived from the somatic embryos with small cotyledons.     

Improved and synchronized maturation of Norway spruce (<Emphasis Type="Italic">Picea abies</Emphasis> (L.) H.Karst.) somatic embryos in temporary immersion bioreactors

Somatic embryogenesis offers many benefits for clonal propagation in large-scale plant production of conifers. A key rate-limiting step is the conversion from early-stage somatic embryos in pro-embryogenic masses (PEMs) to the maturation stage. Immature embryos in PEMs are present at different developmental stages, where some are unable to respond to the maturation treatment, thus limiting yields of mature embryos. Synchronization of early somatic embryo development in PEMs could greatly improve subsequent yields of mature embryos. A temporary immersion bioreactor designed for Norway spruce (Picea abies (L.) H.Karst.) was used in this study. Through a specific system for dispersion, connected tissue of PEMs, composed of immature embryos grown in liquid medium in the temporary immersion bioreactors or on solid medium as a control, was dispersed and redistributed in a more uniform spatial arrangement. It was demonstrated that development of mature embryos could be significantly stimulated by dispersion, compared to controls, in both medium types. Synchronization of maturation was evaluated by a statistical approach. The present study shows that the yield of mature embryos from dispersed PEMs was three to five times higher than that from non-dispersed controls in three of four cell lines of Norway spruce tested, both in bioreactors and on solid medium.     

Induction of somatic embryogenesis and in vitro flowering from inflorescences of chamomile (Chamomilla recutita L.)

A protocol has been developed for the induction of somatic embryogenesis from flower explants of chamomile (Chamomilla recutita L.). The effects of several plant growth regulators [α-naphthylacetic acid (NAA), 2,4-dichlorophenoxyacetic acid, 6-benzyladenine (BA) and kinetin (Kin), alone or in combination] and the flower type (disk or ray flower) were investigated. Both types of flowers responded to the callus and shoot induction treatments, but formation of globular somatic embryos took place only on disk-flower-derived explants after 2–4 weeks of culture on a Murashige and Skoog (MS) medium supplemented either with 8.87 μm BA and 1.07 μm NAA or with 26.8 μm NAA and 11.5 μm Kin. However, fully developed, cotyledonary-stage somatic embryos could be induced only on the NAA/Kin medium, 10 weeks after culture initiation. Germination of the embryos and plant regeneration took place after subculture for 4–5 weeks onto medium of the same composition. Plantlets regenerated from embryos flowered in vitro on a MS medium supplemented with 8.87 μm BA and 1.07 μm NAA. The significance of the results with respect to chamomile micropropagation and the utilization of wild populations in breeding programs is discussed. Received: 6 April 1998 / Revision received: 12 October 1998 / Accepted: 28 October 1998     

High Frequency of Plant Production via Somatic Embryogenesis from Callus or Cell Suspension Cultures inEleutherococcus senticosus

Hypocotyl segments ofEleutherococcus senticosuscultured on Murashigeand Skoog's (MS) medium with 4.5 µM2,4-D produced somaticembryos directly from the surface of explants without interveningcallus formation. When these somatic embryos were subculturedto the same MS medium with 4.5 µM2,4-D, friable embryogeniccalli were formed mainly from radicle tips of somatic embryos,but at a low frequency (5%). Selected embryogenic calli weremaintained on MS agar or liquid medium with 4.5 µM2,4-D.To induce somatic embryo development, embryogenic calli andcell clumps were transferred to MS medium lacking 2,4-D. Thefrequency of somatic embryo formation differed between culturetypes with 1570 embryos formed per Petri dish from callus cultureand 5514 embryos formed per flask from cell suspension cultures.Somatic embryos formed on agar medium had larger cotyledonsthan those of embryos formed in liquid medium. GA₃treatmentwas necessary to induce germination from somatic embryos. Therate of plant conversion was 97% in somatic embryos from callusculture and 76% in embryos from liquid culture. Regeneratedplantlets were successfully acclimatized in the glasshouse.Copyright1999 Annals of Botany Company Eleutherococcus senticosus, micro propagation, somatic embryogenesis.