Fabrication of sucrose biosensor based on single mode planar optical waveguide using co-immobilized plant invertase and GOD

In present studies, the new optical sensing platform based on optical planar waveguide (OPWG) for sucrose estimation was reported. An evanescent-wave biosensor was designed by using novel agarose–guar gum (AG) biopolymer composite sol–gel with entrapped enzymes (acid invertase (INV) and glucose oxidase (GOD)). Partially purified watermelon invertase isolated from Citrullus vulgaris fruit (specific activity 832 units mg⁻¹) in combination with GOD was physically entrapped in AG sol–gel and cladded on the surface of optical planar waveguide. Na⁺–K⁺ ion-exchanged glass optical waveguides were prepared and employed for the fabrication of sucrose biosensor. By addressing the enzyme modified waveguide structure with, the optogeometric properties of adsorbed enzyme layer (12 μm) at the sensor solid–liquid interface were studied. The OPWG sensor with short response time (110 s) was characterized using the 0.2 M acetate buffer, pH 5.5. The fabricated sucrose sensor showed concentration dependent linear response in the range 1 × 10⁻¹⁰ to 1 × 10⁻⁶ M of sucrose. Lower limit of detection of this novel AG–INV–GOD cladded OPWG sensor was found to be 2.5 × 10⁻¹¹ M sucrose, which indicates that the developed biosensor has higher sensitivity towards sucrose as compared to earlier reported sensors using various transducer systems. Biochips when stored at room temperature, showed high stability for 81 days with 80% retention of original sensitivity. These sucrose sensing biochips showed good operational efficiency for 10 cycles. The proper confinement of acid invertase and glucose oxidase in hydrogel composite was confirmed by scanning electron microscopy (SEM) images. The constructed OPWG sensor is versatile, easy to fabricate and can be used for sucrose measurements with very high sensitivity.     

A performance comparison of choline biosensors: anodic or cathodic detections of H2O2 generated by enzyme immobilized on a conducting polymer

Amperometric choline biosensors were fabricated by the covalent immobilization of an enzyme of choline oxidase (ChO) and a bi-enzyme of ChO/horseradish peroxidase (ChO/HRP) onto poly-5,2′:5′,2″-terthiophene-3′-carboxylic acid (poly-TTCA) modified electrodes (CPMEs). A sensor modified with ChO utilized the oxidation process of enzymatically generated H₂O₂ in a choline solution at +0.6 V. The other one modified with ChO/HRP utilized the reduction process of H₂O₂ in a choline solution at −0.2 V. Experimental parameters affecting the sensitivity of sensors, such as pH, applied potential, and temperature were optimized. A performance comparison of two sensors showed that one based on ChO/HRP/CPME had a linear range from 1.0×10⁻⁶ to 8.0×10⁻⁵ M and the other based on ChO/CPME from 1.0×10⁻⁶ to 5.0×10⁻⁵ M. The detection limits for choline employing ChO/HRP/CPME and ChO/CPME were determined to be about 1.0×10⁻⁷ and 4.0×10⁻⁷ M, respectively. The response time of sensors was less than 5 s. Sensors showed good selectivity to interfering species. The long-term storage stability of the sensor based on ChO/HRP/CPME was longer than that based on ChO/CPME.     

Graft copolymerization of acrylic acid onto guar gum initiated by vanadium (V)–mercaptosuccinic acid redox pair

Guar gum has been modified by graft copolymerization with acrylic acid in aqueous medium using vanadium (V)–mercaptosuccinic acid redox system. The optimum reaction conditions affording maximum grafting ratio, efficiency, add on and conversion have been determined. The grafting parameters have been found to increase with increase in vanadium (V) concentration upto 1.0 × 10⁻² mol dm⁻³, but these parameters decrease on further increasing the vanadium (V) concentration. On increasing the mercaptosuccinic acid concentration from 1.0 × 10⁻² to 4.0 × 10⁻² mol dm⁻³ grafting ratio, efficiency and add on increase up to 2.0 × 10⁻² mol dm⁻³ but decrease with further increase in mercaptosuccinic acid concentration. On varying the acrylic acid concentration from 5.0 × 10⁻² to 30.0 × 10⁻² mol dm⁻³, maximum grafting ratio, efficiency and add on have been obtained at 20.0 × 10⁻² mol dm⁻³. The grafting ratio, add on and conversion increase, on increasing the H⁺ ion concentration from 1.5 × 10⁻¹ to 6.0 × 10⁻¹ mol dm⁻³. On increasing the guar gum concentration the grafting parameters increase. The grafting ratio, add on and conversion have been found to increase with time period while efficiency started decreasing after 120 min. It has been observed that %G increases on increasing the temperature up to 35 °C. The graft copolymer has been characterized by IR spectroscopy and thermogravimetric analysis.     

Synthesis of graft copolymer (k-carrageenan-g-N,N-dimethylacrylamide) and studies of metal ion uptake, swelling capacity and flocculation properties

Graft copolymer of k-carrageenan and N,N-dimethylacrylamide has been synthesized by free radical polymerization using peroxymonosulphate/glycolic acid redox pair in an inert atmosphere. The grafting parameters i.e. grafting ratio, add on and efficiency decrease with increase in concentration of k-carrageenan from 0.6 to 1.4 g dm⁻³ and hydrogen ion from 3 × 10⁻³ to 7 × 10⁻³ mol dm⁻³, but these grafting parameters increase with increase in concentration of N,N-dimethylacrylamide from 16 × 10⁻² to 32 × 10⁻² mol dm⁻³, and peroxymonosulphate from 0.8 × 10⁻² to 2.4 × 10⁻² mol dm⁻³. The metal ion sorption, swelling behaviour and flocculation properties have been studied. The intrinsic viscosity of pure and grafted samples has been measured by using Ubbelohde capillary viscometer. Flocculation capability of k-carrageenan and k-carrageenan-g-N,N-dimethylacrylamide for both coking and non-coking coals has been studied for the treatment of coal mine waste water. The graft copolymer has been characterized by Infrared (IR) spectroscopy and thermogravimetric analysis.     

Optimizing the formulation of a myoglobin molecularly imprinted thin-film polymer--formed using a micro-contact imprinting method

Thin-film myoglobin molecularly imprinted polymers have been fabricated using a micro-contact approach. By initially selecting the cross-linker on the basis of it having a minimal recognition for the template and using this as a starting point for functional monomer selection, we have produced myoglobin imprinted polymers with exceptionally high selectivities.

The affinity of the polymers, for myoglobin, when prepared with a variety of different cross-linkers and no functional monomer was evaluated. Of these, tetraethylene glycol dimethacrylate (TEGDMA) exhibited the lowest affinity for the template species. Methyl methacrylate (MMA) was chosen as the functional monomer as when it was used in conjunction with TEGDMA, it exhibited maximum selectivity for the template compared to polymers made with other functional monomers.

With a MMA to TEGDMA ratio of 1 to 3, the myoglobin molecularly imprinted polymer adsorbed 15.03 ± 0.89 × 10⁻¹¹ mole/cm² of template from a 5.68 × 10⁻⁷ M myoglobin solution, compared to 2.58 ± 0.02 × 10⁻¹¹ mole/cm² for a polymer of similar composition, but formed in the absence of a template. Various washing conditions, using alkaline media to remove the template, were investigated. An extraction solvent comprising 2 wt.% SDS and 0.6 wt.% NaOH used at 80 °C for 30 min was shown to give the highest imprinting factor i.e. 5.83 with 72.82% myoglobin removal.

The saturation kinetics of template binding to the thin-film MIP were examined and found to display a simple two-phase profile typical of non-cooperative binding. A Scatchard binding plot showed the dissociation constant (K_d) for the specific binding phase to be 3.4 × 10⁻⁷ M and the binding site capacity to be 7.24 × 10⁻¹¹ mole/cm². For the non-specific binding phase, K_d was found to be 1.355 × 10⁻⁵ M and the binding site capacity was determined as 9.62 × 10⁻¹⁰ mole/cm².

Selectivity experiments were carried out in both single protein and binary protein systems all using a total protein concentration of 5.68 × 10⁻⁷ M. The molar ratio of adsorbed myoglobin to IgG, HSA and hemoglobin was found to 115.5, 230.9 and 2.5, respectively. While, in binary competition systems, myoglobin selectivity to IgG, HSA and hemoglobin was, respectively, 94.18, 98.21 and 61.09%. Rebinding in natural biological matrices, i.e. human serum or urine, showed the imprinted films to have significantly greater uptake than non-imprinted films. Re-binding in undiluted urine was found to be a facile process, with the imprinting factor, i.e. the ratio of MIP to NIP binding, being determined as 37.4.     

Direct glucose determination in blood using a reagentless optical biosensor

This paper demonstrates that glucose determination in blood can be done directly (without sample pretreatment) using a reagentless reversible biosensor based on the intrinsic spectroscopic properties of peroxidase (HRP). The biosensor, prepared by HRP and glucose oxidase entrapment in a polyacrylamide gel matrix, works in continuous mode, presents a linear response range from 1.5 × 10⁻⁶ up to 5.5 × 10⁻⁵ M and can be used for at least 750 measurements; in the best conditions (0.1 M pH 6 phosphate buffer, HRP and GOx amounts in the polymersation mixture for the sensor film preparation 0.0165 and 0.0010 g, respectively) the minimum samples rate is 30 h⁻¹. For glucose determination, blood is simply diluted in water (until haemolysis is completed) and fed into the sensor without a cleaning step between samples; the blood absorption is corrected in a simple way by working at a proper reference wavelength. The biosensor signals have been mathematically modeled in order to facilitate the design of sensors based on the same idea for other biochemical compounds.     

Uptake of corticosterone into isolated rat liver cells: Possible involvement of Na/K-ATPase

Isolated rat hepatocytes posses a saturable glucocorticoid uptake system with high affinity (K_d value = 2.8 ± 0.7 × 10⁻⁸ M; 318,000 ± 80,000 binding sites per cell; 317 fmol/mg protein). The initial rates of uptake decrease by about 30–40% if the cells are incubated simultaneously with [³H]corticosterone and either SH-reagents (N-ethylmaleimide and p-chloromercuriphenylsulphonate, 1 mM), metabolic inhibitors (2,4-dinitrophenol, 1 mM; and antimycin, 0.1 mM) or the Na⁺/K⁺-ATPase-inhibitors, ouabain and quercetine. These Na⁺/K⁺-ATPase-blockers exert half-maximal inhibition at 3 × 10⁻⁷ and 3 × 10⁻⁶ M, respectively. A slight increase in K⁺ concentration and a corresponding decrease in Na⁺ in the medium leads to a significant reduction in the initial uptake rate. The uptake system from the rat hepatocytes shows a clear steroid specificity, being different from the intracellular receptor. Corticosterone and progesterone are the strongest competitors, cortisol, 5- and 5β-dihydrocorticosterone, 11-deoxycorticosterone, cortisone and testosterone have an intermediate effect and only weak competition is exerted by dexamethasone and by the mineralocorticoid, aldosterone. Estradiol and estrone sulphate as well as the synthetic glucocorticoid triamcinolone acetonide are unable to inhibit initial corticosterone uptake.     

SEC of mono-carboxymethyl cellulose (CMC) in a wide range of pH; Mark–Houwink constants

A method for determination of carboxymethyl cellulose (CMC) molecular weight (M_W) and chemical heterogeneity (degree of oxidation (DO)) using a bi-detector HPSEC (UV-detector online with refractometer) has been developed. It has been found that the use of 0.5 N NaOH or 0.4 M acetate buffer as the eluent ensures CMC separation according to M_W. It has been revealed that the universal calibration for the polyelectrolyte CMC and the neutral polymer dextran is valid under the conditions applied. The Mark–Houwink equations for CMC in 0.5 N NaOH and 0.4 M acetate buffer have been estimated to be [η]=5.37×10⁻⁴ M_W^0.73 and [η] =2.24×10⁻⁴ M_W^0.83 dl g⁻¹, respectively. The equation log K=1.64−4.00 ml g⁻¹ for CMC has been estimated. An approach for determining DO from adsorption at 290 or 313 nm has been developed.     

Purification and characterization of a Na/K dependent alginate lyase from turban shell gut Vibrio sp. YKW-34

An alginate lyase with high specific enzyme activity was purified from Vibrio sp. YKW-34, which was newly isolated from turban shell gut. The alginate lyase was purified by in order of ion exchange, hydrophobic and gel filtration chromatographies to homogeneity with a recovery of 7% and a fold of 25. This alginate lyase was composed of a single polypeptide chain with molecular mass of 60 kDa and isoelectric point of 5.5–5.7. The optimal pH and temperature for alginate lyase activity were pH 7.0 and 40 °C, respectively. The alginate lyase was stable over pH 7.0–10.0 and at temperature below 50 °C. The alginate lyase had substrate specificity for both poly-guluronate and poly-mannuronate units. The k_cat/K_m value for alginate (heterotype) was 1.7 × 10⁶ s⁻¹ M⁻¹. The enzyme activity was completely lost by dialysis and restored by addition of Na⁺ or K⁺. The optimal activity exhibited in 0.1 M of Na⁺ or K⁺. This enzyme was resistant to denaturing reagents (SDS and urea), reducing reagents (β-mercaptoethanol and DTT) and chelating reagents (EGTA and EDTA).     

Molecular changes associated with the acquisition of oestrogen hypersensitivity in MCF-7 breast cancer cells on long-term oestrogen deprivation

The growth dependence of many breast cancers on oestrogen has been exploited therapeutically by oestrogen deprivation, but almost all patients eventually develop resistance largely by unknown mechanisms. Wild-type (WT) MCF-7 cells were cultured in oestrogen-deficient medium for 90 weeks in order to establish a long-term oestrogen-deprived MCF-7 (LTED) which eventually became independent of exogenous oestrogen for growth. After 15 weeks of quiescence (LTED-Q), basal growth rate increased in parallel with increasing oestrogen sensitivity. While 10⁻⁹ M oestradiol (E2) maximally stimulated WT growth, the hypersensitive LTED (LTED-H) were maximally growth stimulated by 10⁻¹³ M E2. By week 50, hypersensitivity was apparently lost and the cells became oestrogen independent (LTED-I), although the pure antioestrogen ICI182780 still inhibited cell growth and reversed the inhibitory effect of 10⁻⁹ M E2 at 10⁻¹² to 10⁻⁷ M. Tamoxifen (10⁻⁷ to 10⁻⁶ M) had a partial agonist effect on WT, but had no stimulatory effect on LTED. Whilst LTED cells have a low progesterone receptor (PgR) expression in all phases, oestrogen receptor (ER) a expression was, on average, elevated five- and seven-fold in LTED-H and LTED-I, respectively, and serine118 was phosphorylated. ERβ expression was up-regulated and the levels of insulin receptor substrate 1 (IRS-1) remained low throughout all phases. The levels of RIP140 mRNA appeared to decrease to approximately 50% of the WT message in LTED-Q and remained constant into the hypersensitive phase. No significant changes were observed in the expression of SUG-1, TIF-1 and SMRT in LTED. The overall changes in nuclear receptor interacting proteins do not appear to be involved in the hypersensitivity. Thus, the resistance of these human breast cancer cells to oestrogen-deprivation appears to be due to acquired hypersensitivity which may be explained in part by increased levels of and phosphorylated ER.     

Epinephrine quantification in pharmaceutical formulations utilizing plant tissue biosensors

A plant tissue biosensor associated with flow injection analysis is proposed to determine epinephrine in pharmaceutical samples. The polyphenol oxidase enzymes present in the fibers of a palm tree fruits (Livistona chinensis), catalyses the oxidation of epinephrine to epinephrinequinone as a primary product. This product is then electrochemically reduced (at −0.10 V versus Ag/AgCl_sat) on the biosensor surface and the resulting current is used for the quantification of epinephrine. The biosensor provides a linear response for epinephrine in the concentration range from 5.0 × 10⁻⁵ to 3.5 × 10⁻⁴ mol l⁻¹. The limit of detection estimated for this interval was 1.5 × 10⁻⁵ mol l⁻¹ and the correlation coefficient of 0.998, working under a flow rate of 2.0 ml min⁻¹ and using a sample loop of 100 μl. The repeatability (R.S.D. for 10 consecutive determinations of a 3.0 × 10⁻⁴ mol l⁻¹ epinephrine solution) was 3.1%. The results obtained by the method here proposed were compared with the official UV spectrophotometric procedure and also using a plant tissue reactor. The responses obtained with the proposed strategies were in good agreement with both ways of analyses, whereas the values obtained by the official spectrophotometric method was strongly affected by benzoic acid, present in the formulation of pharmaceutical product utilized for inhalation. Such favorable results obtained with the carbon paste biosensor or utilizing the bioreactor, joined with the simplicity of its preparation turns these procedures very attractive for epinephrine quantification in pharmaceutical products.     

Glucose biosensor based on immobilization of glucose oxidase in poly(o-aminophenol) film on polypyrrole-Pt nanocomposite modified glassy carbon electrode

Novel Pt nanoclusters embedded polypyrrole nanowires (PPy-Pt) composite was electrosynthesized on a glassy carbon electrode, denoted as PPy-Pt/GCE. A glucose biosensor was further fabricated based on immobilization of glucose oxidase (GOD) in an electropolymerized non-conducting poly(o-aminophenol) (POAP) film that was deposited on the PPy-Pt/GCE. The morphologies of the PPy nanowires and PPy-Pt nanocomposite were characterized by field emission scanning electron microscope (FE-SEM). Effect of experimental conditions involving the cycle numbers for POAP deposition and Pt nanoclusters deposition, applied potential used in glucose determination, temperature and pH value of the detection solution were investigated for optimization. The biosensor exhibited an excellent current response to glucose over a wide linear range from 1.5 × 10⁻⁶ to 1.3 × 10⁻² M (r = 0.9982) with a detection limit of 4.5 × 10⁻⁷ M (s/n = 3). Based on the combination of permselectivity of the POAP and the PPy films, the sensor had good anti-interference ability to ascorbic acid (AA), uric acid (UA) and acetaminophen. The apparent Michaelis–Menten constant (K_m) and the maximum current density (I_m) were estimated to be 23.9 mM and 378 μA/cm², respectively. In addition, the biosensor had also good sensitivity, stability and reproducibility.     

Binding of genistein to human serum albumin demonstrated using tryptophan fluorescence quenching

Genistein is an isoflavone and phytoestrogen that is a potent inhibitor of cell proliferation and angiogenesis. This study was designed to investigate the binding of genistein to human serum albumin (HSA) under physiological conditions with drug concentrations in the range of 6.7 × 10⁻⁶ to 2.0 × 10⁻⁵ mol L⁻¹ and HSA concentration at 1.5 × 10⁻⁶ mol L⁻¹. Fluorescence quenching methods in combination with Fourier transform infrared (FT-IR) spectroscopy and circular dichroism (CD) spectroscopy was used to determine the binding mode, the binding constant and the protein structure changes in the presence of genistein in aqueous solution. Changes in the CD spectra and FT-IR spectra were observed upon ligand binding, and the degree of tryptophan fluorescence quenching change did significantly in the complexes. These data have proved the change in protein secondary structure accompanying ligand binding. The change in tryptophan fluorescence intensity was used to determine the binding constants. The thermodynamic parameters, the enthalpy change (ΔH) and the entropy change (ΔS) were calculated to be −22.24 kJ mol⁻¹and 19.60 J mol⁻¹ K⁻¹ according to the van’t Hoff equation, which indicated that hydrophobic and electrostatic interactions play the main role in the binding of genistein to HSA.     

Effects of interactions with micellar interfaces on the activity and structure of different lipolytic isoenzymes from Candida rugosa

The conformational and functional changes of cholesterol esterase (CE) and isolipase (CRL) from Candida rugosa after exposure to a micellar interface and subsequent extraction to a fresh buffer were studied. These two enzymes were activated by interaction with the micellar interface of a sulphosuccinic acid bis[2-ethylhexyl] ester/n-heptane/water system. For the hydrolysis of p-nitrophenyl butyrate ester in water, the catalytic efficiencies of CE and CRL were both improved because on activation their k_cat values increased from 378 to 465 and from 250 to 680 s⁻¹, respectively, while their K_m values decreased from 5.08 × 10⁻⁵ to 3.23 × 10⁻⁵ and from 2.28 × 10⁻⁴ to 1.14 × 10⁻⁴ M, respectively. After exposure to the micelles, CE showed a marked increase in its -helical content from 28 to 49%, but only limited changes were detected when CRL was exposed. These proteins exhibit similar capacities for increasing their -helical content in a helicogenic medium. In acetonitrile/water mixtures, CRL exhibits a partial decrease in the extent of its secondary structure, while CE exhibits an increase in its -helical content. The fact that this medium of reduced polarity permits one to simulate the effect of the AOT reverse micelles on the conformation of CE (increased helicity) but not their effect on the structure of CRL (decreased helicity) supports the hypothesis that only CE interacts to a significant extent with the apolar side of the micellar interface. After exposure to micelles of octyl-β-glucopyranoside, CE (but not CRL) showed a 10% increase in its -helical content.     

Estradiol inhibits the estrone sulfatase activity in normal and cancerous human breast tissues

It is well accepted that estradiol (E₂) plays an important role in the genesis and evolution of breast cancer. Quantitative evaluation indicates that in human breast tumor, estrone sulfate (E₁S) ‘via sulfatase’ is a much more likely precursor for E₂ than is androstenedione ‘via aromatase’. In previous studies, it was demonstrated that in isolated MCF-7 and T-47D breast cancer cell lines, estradiol can block estrone sulfatase activity. In the present study, the effect of E₂ was explored using total normal and cancerous breast tissues. This study was carried out with post-menopausal patients with breast cancer. None of the patients had a history of endocrine, metabolic or hepatic diseases or had received treatment in the previous 2 months. Each patient received local anaesthetic (lidocaine 1%) and two regions of the mammary tissue were selected: (A) the tumoral tissue and (B) the distant zone (glandular tissue) which was considered as normal. Samples were placed in liquid nitrogen and stored at –80 °C until enzyme activity analysis. Breast cancer histotypes were ductal and post-menopausal stages were T2. Homogenates of tumoral or normal breast tissues (45–75 mg) were incubated in 20 mM Tris–HCl, pH 7.2 with physiological concentrations of [³H]-E₁S (5 × 10⁻⁹ M) alone or in the presence of E₂ (5 × 10⁻⁵ to 5 × 10⁻⁷ M) during 30 min or 3 h. E₁S, E₁ and E₂ were characterized by thin layer chromatography and quantified using the corresponding standard. The sulfatase activity is significantly more intense with the breast cancer tissue than normal tissue, since the concentration of E₁ was 3.20 ± 0.15 and 0.42 ± 0.07 pmol/mg protein, respectively after 30 min incubation. The values were 27.8 ± 1.8 and 3.5 ± 0.21 pmol/mg protein, respectively after 3 h incubation. Estradiol at the concentration of 5 × 10⁻⁷ M inhibits this conversion by 33% and 31% in cancerous and normal breast tissues, respectively and by 53% and 88% at the concentration of 5 × 10⁻⁵ M after 30 min incubation. The values were 24% and 18% for 5 × 10⁻⁷ M and 49% and 42% for 5 × 10⁻⁵ M, respectively after 3 h incubation. It was observed that [³H]-E₁S is only converted to [³H]-E₁ and not to [³H]-E₂ in normal or cancerous breast tissues, which suggests a low or no 17β-hydroxysteroid dehydrogenase (17β-HSD) Type 1 reductive activity in these experimental conditions. In conclusion, estradiol is a strong anti-sulfatase agent in cancerous and normal breast tissues. This data can open attractive perspectives in clinical trials using this hormone.     

Angiotensin II and angiotensin-(1-7) inhibit the inner cortex Na+ -ATPase activity through AT2 receptor

In the present paper, the modulation of the basolateral membrane (BLM) Na⁺-ATPase activity of inner cortex from pig kidney by angiotensin II (Ang II) and angiotensin-(1–7) (Ang-(1–7)) was evaluated. Ang II and Ang-(1–7) inhibit the Na⁺-ATPase activity in a dose-dependent manner (from 10⁻¹¹ to 10⁻⁵ M), with maximal effect obtained at 10⁻⁷ M for both peptides. Pharmacological evidences demonstrate that the inhibitory effects of Ang II and Ang-(1–7) are mediated by AT₂ receptor: The effect of both polypeptides is completely reversed by 10⁻⁸ M PD 123319, a selective AT₂ receptor antagonist, but is not affected by either (10⁻¹²–10⁻⁵ M) losartan or (10⁻¹⁰–10⁻⁷ M) A779, selective antagonists for AT₁ and AT_(1–7) receptors, respectively. The following results suggest that a PTX-insensitive, cholera toxin (CTX)-sensitive G protein/adenosine 3′,5′-cyclic monophosphate (cAMP)/PKA pathway is involved in this process: (1) the inhibitory effect of both peptides is completely reversed by 10⁻⁹ M guanosine 5′-O-(2-thiodiphosphate) (GDPβS; an inhibitor of the G protein activity), and mimicked by 10⁻¹⁰ M guanosine 5′-O-(3-thiotriphosphate) (GTPγS; an activator of the G protein activity); (2) the effects of both peptides are mimicked by CTX but are not affected by PTX; (3) Western blot analysis reveals the presence of the G_s protein in the isolated basolateral membrane fraction; (4) (10⁻¹⁰–10⁻⁶ M) cAMP has a similar and non-additive effect to Ang II and Ang-(1–7); (5) PKA inhibitory peptide abolishes the effects of Ang II and Ang-(1–7); and (6) both angiotensins stimulate PKA activity.     

Comparison of the characterization on binding of alpinetin and cardamonin to lysozyme by spectroscopic methods

Studies on the binding affinity of protein to the active components of herbs are novel in biochemistry and are valuable for the information about speciation of drugs and exchange in biological systems. Alpinetin and cardamonin, two of the main constituents from the seeds of Alpinia katsumadai Hayata, have been used in traditional herbs as antibacterial, anti-inflammatory, and other important therapeutic activities of significant potency and low systemic toxicity. The interactions between two flavonoids analogs and lysozyme have been studied for the first time by spectroscopic method including Fourier transform infrared (FT-IR) spectroscopy, circular dichroism (CD) and UV-absorption spectroscopy in combination with Fluorescence quenching study. Both molecules showed high affinities to lysozyme under the experimental condition with drug concentrations from 3.33 × 10⁻⁶ to 2.67 × 10⁻⁵ mol L⁻¹ for alpinetin and 1.67 × 10⁻⁶ to 13.33 × 10⁻⁶ mol L⁻¹ for cardamonin. The alterations of protein secondary structure in the presence of drugs in aqueous solution were quantitatively estimated by the evidences from CD and FT-IR spectroscopy. The thermodynamic parameters obtained and the results of spectroscopic measurements suggest that hydrophobic and electrostatic interactions are the predominant intermolecular forces stabilizing two coordination compounds. The quenching mechanism and the number of binding site (n ≈ 1) were obtained by fluorescence titration data. The efficiency of energy transfer provided the binding distances of 4.04 and 5.90 nm for alpinetin-LYSO and cardamonin-LYSO systems, respectively.     

Determination of digoxin in serum samples using a flow-through fluorosensor based on a molecularly imprinted polymer

This work describes the development of a competitive flow-through FIA assay for digoxin using a molecularly imprinted polymer (MIP) as the recognition phase. In previous work, a number of non-covalent imprinted polymers were synthesised by “bulk” polymerisation. The digoxin binding and elution characteristics of these MIPs were then evaluated to obtain a highly selective material for integration into a sensor. The optimum MIP was synthesised by photo-initiated polymerisation of a mixture containing digoxin, MAA, EDGMA and AIBN in acetonitrile. The bulk polymer was ground and sieved and the template removed by Soxhlet extraction in MeOH/ACN. The MIP was packed into a flow cell and placed in a spectrofluorimeter to integrate the reaction and detection systems. The physical and chemical variables involved in digoxin determination by the sensor (nature and concentration of solution, flow rates, etc.) were optimised. Binding with the non-imprinted polymer (NIP) was also analysed. The new fluorosensor showed high selectivity and sensitivity, a detection limit of 1.7 × 10⁻² μg l⁻¹, and high reproducibility (R.S.D. of 1.03% and 1.77% for concentrations of 1.0 × 10⁻³ and 4.0 × 10⁻³ mg l⁻¹, respectively). Selectivity was tested by determining the cross-reactivity of several compounds with structures analogous to digoxin. Under the assay conditions used, in which the potential interfering compounds were in concentrations 100 times higher than that of the analyte, no interference was recorded. The proposed fluorosensor was successfully used to determine digoxin concentration of human serum samples.     

Immobilization of horseradish peroxidase on chitosan/silica sol-gel hybrid membranes for the preparation of hydrogen peroxide biosensor

A simple and effective strategy for fabrication of hydrogen peroxide (H₂O₂) biosensor has been developed by entrapping horseradish peroxidase (HRP) in chitosan/silica sol–gel hybrid membranes (CSHMs) doped with potassium ferricyanide (K₃Fe(CN)₆) and gold nanoparticles (GNPs) on platinum electrode surface. The hybrid membranes are prepared by cross-linking chitosan (CS) with 3-aminopropyltriethoxysilane (APTES), while the presence of GNPs improved the conductivity of CSHMs, and the Fe(CN)₆^3−/4− was used as a mediator to transfer electrons between the electrode and HRP due to its excellent electrochemistry activity. UV–Vis absorption spectroscopy was employed to characterize the different components in the CSHMs and their interaction. The parameters influencing the performance of the resulting biosensor were optimized and the characteristic of the resulting biosensor was characterized by cyclic voltammetry and chronoamperometry. Linear calibration for hydrogen peroxide was obtained in the range of 3.5 × 10^− 6 to 1.4 × 10^− 3 M under the optimized conditions with the detection limit (S/N = 3) of 8.0 × 10^− 7 M. The apparent Michaelis–Menten constant of the enzyme electrode was 0.93 mM. The enzyme electrode retained about 78% of its response sensitivity after 30 days. The system was applied for the determination of the samples, and the results obtained were satisfactory.     

Beta-endorphin-like peptide SLTCLVKGFY reduces the production of 11-oxycorticosteroids by rat adrenal cortex through nonopioid beta-endorphin receptors

β-Endorphin-like peptide immunorphin (SLTCLVKGFY), a selective agonist of nonopioid β-endorphin receptor, was labeled with tritium to specific activity of 24 Ci/mmol. It was used for the detection and characterization of nonopioid β-endorphin receptors on rat adrenal cortex membranes (K_d=31.6±0.2 nM, B_max=37.4±2.2 pmol/mg protein). Immunorphin at concentrations of 10⁻⁹ to 10⁻⁶ M was found to inhibit the adenylate cyclase activity in adrenal cortex membranes, while intramuscular injection of immunorphin at doses of 10–100 μg/kg was found to reduce the secretion of 11-oxycorticosteroids from the adrenals to the bloodstream.