A highly sensitive micelle-enhanced synchronous spectrofluorimetric determination of the recently approved co-formulated drugs,bilastine and montelukast in pharmaceuticals and human plasma at nanogram levels

In this study, the simultaneous determination of bilastine and montelukast, two recently approved co-formulated antihistaminic medications, was accomplished using a quick, sensitive, environmentally friendly, and reasonably priced synchronous fluorescence spectroscopic approach for the first time. Enhancement of the method's sensitivity down to nanogram levels was achieved by the addition of sodium dodecyl sulfate (1.0% w/v) as a micellar system. According to the results, bilastine and montelukast's fluorescence was measured at 255.3 and 355.3 nm, respectively, using Δλ of 40.0 nm and distilled water as a green diluting solvent. With respect to the concentration ranges of bilastine (5.0–300.0 ng/ml) and montelukast (50.0–1000.0 ng/ml), the method showed excellent linearity (r ≥ 0.9998). The results showed that the suggested method is highly sensitive, with detection limits of 1.42 and 13.74 ng/ml for bilastine and montelukast, respectively. Within-run precisions (intra- and interday) per cent relative standard deviations (RSD) for both analytes were <0.59%. With high percentage recoveries and low percentage RSD values, the designed approach was successfully applied for the simultaneous estimation of the cited medications in their dosage form and human plasma samples. To evaluate the green profile of the suggested method, an analytical GREENNESS metric approach (AGREE) and green analytical procedure index (GAPI) metric tools were used. These two methods for evaluating greenness confirmed that the developed method met the highest number of green requirements, recommending its use as a green substitute for the routine analysis of the studied drugs. The proposed approach was validated according to ICHQ2 (R1) guidelines.     

Utilization of erythrosine B in spectrofluorimetric quenching analysis of amlodipine and perindopril in pharmaceutical and biological matrices

A spectrofluorimetric approach that is sensitive, simple, validated, and cost-effective has been proposed for the estimation of amlodipine (AML) and perindopril (PER) in their bulk powders, pharmaceutical formulations, and spiked human plasma. The recommended approach utilized the quantitative quenching effect of the two cited drugs on the fluorescence intensity of erythrosine B, as a result of complex binary reactions among each drug with erythrosine B at pH 3.5 (Teorell and Stenhagen buffer). The quenching of erythrosine B fluorescence was recorded at 554 nm after excitation at 527 nm. The calibration curve was detected in the range 0.25–3.0 μg ml⁻¹, with a correlation coefficient of 0.9996 for AML, and 0.1–1.5 μg ml⁻¹, with a correlation coefficient of 0.9996 for PER. The established spectrofluorimetric approach was validated for the estimation of the cited drugs with high sensitivity regarding International Council on Harmonization guidelines. Therefore, the established approach could be utilized for quality control of the cited drugs in their pharmaceutical formulations.     

Simultaneous determination of citalopram and tadalafil by the second derivative synchronous fluorescence method in biological fluids; application of Box–Behnken optimization design

This is the first study focusing solely on that determination of tadalafil in the presence of citalopram as an antidepressant drug. The determination in biological fluids of a co‐administered antidepressant drug and a sexual stimulation drug is a very critical and important step for psychotic and ischaemic heart disease patients, especially in cases of emergency and this requires therapeutic drug monitoring. A sensitive, efficient and rapid assay was selected satisfactorily and applied for simultaneous determination of citalopram and tadalafil either in their pure forms, in tablet dosage forms or in spiked human plasma. There was a large overlap for both drugs, forming the broad band found in conventional fluorescence spectra and their related synchronous fluorescence intensity. Therefore, the development of a highly sensitive second derivative synchronous fluorescence method was demonstrated that removed this overlap. The proposed method depended on measuring the amplitudes of the second derivative of synchronous fluorescence intensity at suitable wavelengths of 301 nm and 367 nm for citalopram and tadalafil at Δλ = 60 nm, respectively. Box–Behnken design as a response surface methodology was used to fit models and create an optimization process encompassing a set of factors and resulting in an optimum response value specifically designed for this method. Under optimum conditions, the linear dynamic ranges for citalopram and tadalafil estimation were 20–900 and 5–400 ng ml^?1 with detection limits of 5.40 and 1.43 ng ml^?1, respectively.     

Quantitative analysis of favipiravir and hydroxychloroquine as FDA-approved drugs for treatment of COVID-19 using synchronous spectrofluorimetry: application to pharmaceutical formulations and biological fluids

Coronavirus disease 2019 (COVID-19) is a contagious viral infection caused by coronavirus 2 (SARS-CoV-2) that causes severe acute respiratory syndrome. It has ravaged several countries and burdened many healthcare systems. As the process of authorizing a novel treatment for human use is extensive and involves multiple phases to obtain safety information and identify potential concerns. Therefore, the fastest and easiest choice was to use United States Food and Drug Administration (US FDA)-approved drugs such as favipiravir and hydroxychloroquine. For the simultaneous estimation of both medications, a simple synchronous spectrofluorimetric approach was established in which both drugs were measured at 372 and 323 nm, respectively in the presence of each other without interference at Δλ 60 nm. The effect of various experimental conditions on synchronous fluorescence intensities were thoroughly investigated and optimized. The maximum synchronous fluorescence intensities were obtained at pH 5.4 using acetate buffer (0.2 M, 0.5 ml) and ethanol as a diluent. Excellent linearity ranges were obtained using 1.0–18.0 ng/ml and 10.0–120.0 ng/ml for favipiravir and hydroxychloroquine, respectively. The approach exhibited high sensitivity with detection limits down to 0.25 ng/ml and 1.52 ng/ml and quantitation limits down to 0.77 ng/ml and 4.62 ng/ml, respectively. Spiking human plasma samples with the studied drugs yielded high % recoveries, allowing a significant bioanalytical application. Moreover, the method was validated according to International Conference on Harmonization guidelines and further applied to commercial pharmaceutical preparations with good results.     

Micellar-emphasized simultaneous determination of ivabradine hydrochloride and felodipine using synchronous spectrofluorimetry

A sensitive and green micellar spectrofluorimetric approach was applied for the simultaneous estimation of ivabradine hydrochloride (IVB) and felodipine (FLD) in the ng/ml concentration range. The approach depended on measuring the first derivative synchronous peak amplitude (¹D) of both drugs at ∆λ = 60 nm in a Tween-80 micellar system. The method was rectilinear alongside the concentration ranges 0.02–0.4 μg/ml and 0.05–1.0 μg/ml at 269.5 nm and 378.5 nm for IVB and FLD, respectively. The proposed method was validated by following the International Council for Harmonization guidelines. The method was successfully applied without interference for laboratory-prepared synthetic mixtures, single pharmaceutical preparations, and within spiked biological fluids with acceptable percentage recoveries. A comparison of the performance of the suggested method with other methods, showed no discrepancy. The method’s ecofriendly property evaluated using three different tools, confirming an excellent green method.     

Zero and second‐derivative synchronous fluorescence spectroscopy for the quantification of two non‐classical β‐lactams in pharmaceutical vials: Application to stability studies

The formation of metal chelates with various ligands may lead to the production of fluorescent chelates or enhance the fluorescence of the chelating agent. This paper describes two sensitive, selective and computer‐solved methods, namely, zero order (SF) and second‐derivative synchronous spectrofluorimetry (SDSFS) for nano‐quantitation of two carbapenems; meropenem (MP) and ertapenem (EP). The methods are based on the chelation of MP with Tb³⁺ and EP with Zr⁴⁺ in buffered organic medium at pH 4.0 to produce fluorescent chelates. In the zero order method, the relative synchronous fluorescence intensity is measured at 327.0 nm at Δλ = 70.0 and 100.0 nm for MP and EP, respectively. The second method utilizes a second‐derivative technique to enhance the method selectivity and emphasize a stability‐indicating approach. The peak amplitudes (²D) of the second‐derivative synchronous spectra were estimated to be 333.06 and 330.06 nm for MP and EP, respectively. The proposed synchronous spectrofluorimetric methods were validated according to the International Conference on Harmonization (ICH) guidelines and applied successfully for the analysis of MP and EP in pure forms, pharmaceutical vials and in synthetic mixtures with different degradants of both drugs. Under optimum conditions, the mole‐ratio method was applied and the co‐ordination ratios of MP–Tb³⁺ and EP–Zr⁴⁺chelates were found to be 1:1 and 1:3. The formation constants for the chelation complexes were evaluated using the Benesi–Hildebrand's equation; the free energy change (ΔG) was also calculated. The results indicated that EP–Zr⁴⁺ was more stable than the MP–Tb³⁺ chelate. Moreover, the developed methods were found to be selective and inexpensive for quantitative determination of both drugs in quality control laboratories at nano‐levels.     

Synchronous spectrofluorometric methods for simultaneous determination of diphenhydramine and ibuprofen or phenylephrine in combined pharmaceutical preparations

Simple and rapid synchronous fluorometric methods were adopted and validated for the simultaneous analysis of a binary mixture of diphenhydramine (DIP) and ibuprofen (IBU) ( Mix I) or DIP and phenylephrine (PHE) (Mix II) in their co‐formulated pharmaceuticals without prior separation. Analysis of Mix I is based on the measurement of the peak amplitudes (D¹) of synchronous fluorescence intensities at 265.1 nm for DIP and 260 nm for IBU. The relationship between the concentration and the amplitude of the first‐derivative synchronous fluorescence spectra showed good linearity over the concentration ranges 0.50–10.00 μg ml^?1 and 0.50–7.90 μg ml^?1 for DIP and IBU, respectively. Analysis of Mix II was based on measurement of the peak amplitude (D¹) synchronous fluorescence intensities at 230 nm for DIP and at 253.9 nm for PHE. Moreover, for Mix II, the peak amplitude (D²) synchronous fluorescence intensities were measured at 227.9 nm for DIP and at 264.9 nm for PHE. Calibration plots were rectilinear over the concentration range 0.30–3.50 μg ml^?1 and 0.03–0.75 μg ml^?1 for DIP and PHE, respectively. The proposed methods were successfully applied to determine the studied compounds in pure form and in pharmaceutical preparations.     

Second‐derivative synchronous spectrofluorimetric determination of nebivolol hydrochloride and amlodipine besylate in their combined dosage form

A rapid, simple, accurate and highly sensitive spectrofluorimetric method was developed for the simultaneous analysis of nebivolol hydrochloride (NEB) and amlodipine besylate (AML). The method was based on measuring the synchronous fluorescence intensity of the drugs at Δλ = 40 nm in methanol. Various experimental parameters affecting the synchronous fluorescence of the studied drugs were carefully studied and optimized. The calibration plots were rectilinear over concentration ranges of 0.05–1.5 µg/mL and 0.5–10 µg/mL for NEB and AML with limits of detection (LOD) of 0.010 and 0.051 µg/mL and limits of quantitation (LOQ) of 0.031 and 0.156, respectively. The peak amplitudes (²D) of the second derivative synchronous fluorimetry (SDSF) were estimated at 282 nm for NEB and at 393 nm for AML. Good linearity was obtained over the concentration ranges. The proposed method was successfully applied to the determination of the studied compounds in laboratory‐prepared mixtures, commercial single and laboratory‐prepared tablets. The results were in good agreement with those obtained using the comparison method. The mean percent recoveries were found to be 100.12 ± 0.77 and 99.91 ± 0.77 for NEB and AML, respectively. Copyright © 2015 John Wiley & Sons, Ltd.     

Application of a white and green spectrofluorimetric approach for facile quantification of amlodipine,a hypotensive drug,in batch materials,dosage forms,and biological fluids; content homogeneity testing

The suggested study adheres to a particular protocol to ensure that the process is environmentally friendly and sustainable. It is worth mentioning that several tools have been adopted as prospective measures of the method greenness. Fortunately, the established analytical method is identified as white by the white analytical chemistry (WAC) concept, which uses the red/ green/blue color scheme (RGB 12 tool) to combine ecological and functional factors for the first time in studying of the cited drug. Amlodipine (AMD), a cardiovascular treating agent, belongs to the dihydropyridine class of oral calcium channel-blocking agents. This article presents a novel, simple, green, one-pot-processed, fast, and ultrasensitive fluorimetric approach for monitoring and assessment of AMD using molecular-size-dependent fluorescence augmentation of the light scattering-driven signal of eosin, a biological stain at a wavelength of 415 nm. This enhancement was directly proportional to the size of the produced complex. The linearity range was from 30 to 900 ng mL⁻¹, with corresponding sensitivity limits (detection and quantitation levels) of 9.2 and 28 ng mL⁻¹, respectively. The planned approach was also successfully used to track AMD content in bulk, dosage forms, and bio-fluids (human plasma and urine). The developed method's eco-friendliness was established by different eco-rating metric tools.     

Simultaneous determination of desloratadine and montelukast sodium using second‐derivative synchronous fluorescence spectrometry enhanced by an organized medium with applications to tablets and human plasma

A rapid, simple, and sensitive second‐derivative synchronous fluorimetric method has been developed and validated for the simultaneous analysis of a binary mixture of desloratadine (DSL) and montelukast sodium (MKT) in their co‐formulated tablets. The method is based on measurement of the synchronous fluorescence intensities of the two drugs in McIlvaine's buffer, pH 2.3, in the presence of carboxy methyl cellulose sodium (CMC) as a fluorescence enhancer at a constant wavelength difference (Δλ) of 160 nm. The presence of CMC enhanced the synchronous fluorescence intensity of DSL by 216% and that of MKT by 28%. A linear dependence of the concentration on the amplitude of the second derivative synchronous fluorescence spectra was achieved over the ranges of 0.10–2.00 and 0.20–2.00 µg/mL with limits of detection of 0.02 and 0.03, and limits of quantification of 0.05 and 0.10 µg/mL for DSL and MKT, respectively. The proposed method was successfully applied for the determination of the studied compounds in laboratory‐prepared mixtures and tablets. The results were in good agreement with those obtained with the comparison method. The high sensitivity attained by the proposed method allowed the determination of MKT in spiked human plasma with average % recovery of 100.11 ± 2.44 (n = 3). Copyright © 2014 John Wiley & Sons, Ltd.     

Environmentally benign first derivative synchronous spectrofluorimetry for the analysis of two binary mixtures containing duloxetine with avanafil or tadalafil in spiked plasma samples

Antidepressants can cause sexual dysfunction side effects, necessitating the co-administration of phosphodiesterase type 5 inhibitors. The simultaneous determination of these drugs in biological fluids is critical for therapeutic drug monitoring. For the first time, two binary mixtures containing duloxetine with either avanafil or tadalafil were estimated utilizing simple green spectrofluorimetric methods without the need for a previous separation step. The study was based on first derivative synchronous spectrofluorimetry in ethanol using a change in wavelength difference (∆λ) of 20 and 25 nm for the first and second combinations, respectively. Duloxetine and avanafil were estimated at 297.7 and 331 nm in their binary mixture, while duloxetine and tadalafil were determined at 290.3 and 297.7 nm, respectively. The linearity was achieved over the ranges of 0.1–1.5 μg mL⁻¹ for both duloxetine and avanafil and 0.01–0.40 μg mL⁻¹ for tadalafil, with limits of detection of 0.013, 0.022, and 0.004 μg mL⁻¹ for duloxetine, avanafil, and tadalafil, respectively. Successful application of the developed approaches was accomplished for the estimation of the two mixtures in dosage forms as well as human plasma with excellent percentage recoveries (96–103.75% in plasma), which supports their suitability for use in quality control laboratories and pharmacokinetic studies. Moreover, the adopted approaches' greenness was evidenced by applying three tools.     

Isoquinoline-based intrinsic fluorescence assessment of erythropoiesis-stimulating agent,Roxadustat (FG-4592), in tablets: applications to content uniformity and human plasma evaluation

In the present study, a first validated and green spectrofluorimetric approach for its assessment and evaluation in different matrices was investigated. After using an excitation wavelength of 345 nm, Roxadustat (ROX) demonstrates a highly native fluorescence at an emission of 410 nm. The influences of experimental factors such as pH, diluting solvents, and different organized media were tested, and the most appropriate solvent choice was ethanol. It was confirmed that there was a linear relationship between the concentration of ROX and the relative fluorescence intensity in the range 60.0–1000.0 ng ml^−1, with the limit of detection and limit of quantitation, respectively, being 17.0 and 53.0 ng ml⁻¹. The mean recoveries % [±standard deviation (SD), n = 5] for pharmaceutical preparations were 100.11% ± 2.24%, whereas for plasma samples, they were 100.08 ± 1.08% (±SD, n = 5). The results obtained after the application of four greenness criteria, Analytical Eco-Scale metric, NEMI, GAPI, and AGREE metric, confirmed its eco-friendliness. In addition, the whiteness meter (RGB12) confirmed its level of sustainability. The International Council for Harmonisation (ICH) criteria were used to verify the developed method through the study in both spiked plasma samples and content uniformity evaluation. An appropriate standard for various applications in industry and quality control laboratories was developed.     

Utility of Hantzsch reaction for development of highly sensitive spectrofluorimetric method for determination of alfuzosin and terazosin in bulk,dosage forms and human plasma

A highly sensitive, cheap, simple and accurate spectrofluorimetric method has been developed and validated for the determination of alfuzosin hydrochloride and terazosin hydrochloride in their pharmaceutical dosage forms and in human plasma. The developed method is based on the reaction of the primary amine moiety in the studied drugs with acetylacetone and formaldehyde according to the Hantzsch reaction, producing yellow fluorescent products that can be measured spectrofluorimetrically at 480 nm after excitation at 415 nm. Different experimental parameters affecting the development and stability of the reaction products were carefully studied and optimized. The fluorescence–concentration plots of alfuzosin and terazosin were rectilinear over a concentration range of 70–900 ng ml^?1, with quantitation limits 27.1 and 32.2 ng ml^?1 for alfuzosin and terazosin, respectively. The proposed method was validated according to ICH guidelines and successfully applied to the analysis of the investigated drugs in dosage forms, content uniformity test and spiked human plasma with high accuracy.     

Eco-friendly synchronous fluorescence spectrofluorimetric method for simultaneous determination of montelukast sodium and fexofenadine hydrochloride in their antiallergic rhinitis fixed-dose combination tablets

An innovative, simple, accurate, sensitive, and eco-friendly synchronous fluorescence spectrofluorimetric method has been developed for the simultaneous analysis of montelukast sodium (MON) and fexofenadine hydrochloride (FEX). The method relies on measuring the relative synchronous fluorescence intensity of both drugs using Δλ of 60 nm in methanol at 405 nm for MON and 288 nm for FEX. The experimental parameters influencing the developed method were investigated and optimized. The method was linear over the ranges 0.1–2.0 and 2.0–20.0 μg/ml for MON and FEX, respectively. The limits of detection were 0.018 and 0.441 μg/ml, and the limits of quantitation were 0.055 and 1.336 μg/ml for MON and FEX, respectively. The developed method was applied successfully for the determination of the two drugs in their newly released fixed-dose combination prescribed for the treatment of allergic rhinitis. The mean per cent recoveries were found to be 100.680 ± 0.890 and 100.110 ± 0.940 for MON and FEX, respectively. Furthermore, the method was found to be eco-friendly green as was evaluated according to the Green Analytical Procedure Index tool guidelines and analytical eco-scale.     

Fast concurrent determination of guaifenesin and pholcodine in formulations and spiked plasma using first derivative synchronous spectrofluorimetric approach

Guaifenesin and pholcodine are frequently co-formulated in certain dosage forms. A new fast first derivative synchronous spectrofluorometric method has been used for their simultaneous analysis in mixtures. Here, first derivative synchronous spectrofluorometry enabled the successful simultaneous estimation of guaifenesin at 283 nm and pholcodine at 275 nm using a wavelength difference (Δλ) of 40 nm. The method was fully validated following International Council of Harmonization guidelines. For guaifenesin and pholcodine, linearity was determined within the corresponding ranges of 0.05–0.30 and 0.10–6.0 μg/ml. The two drugs were effectively analyzed using the developed approach in their respective formulations, and the results showed good agreement with those attained using reference methods. The method demonstrated excellent sensitivity, with detection limits down to 0.007 and 0.030 μg/ml and quantitation limits of 0.020 and 0.010 μg/ml for guaifenesin and pholcodine, respectively. Therefore, the procedure was successful in determining these drugs simultaneously in vitro in spiked plasma samples and syrup dosage form. The developed methodology also offered an environmentally friendly advantage by utilizing water as the optimal diluting solvent throughout the whole work. Different greenness approaches were investigated to ensure the method’s ecofriendly properties.     

Utility of the food colorant erythrosine B as an effective green probe for quantitation of the anticancer sunitinib. Application to pharmaceutical formulations and human plasma

Sunitinib is a tyrosine kinase inhibitor used for the treatment of renal cell carcinoma and gastrointestinal stromal tumors. In this study, two spectroscopic methods, spectrofluorometric and spectrophotometric, were utilized to quantify sunitinib in different matrices. In method I, the native fluorescence of erythrosine B was quenched by forming ion-pair complex with increasing quantities of sunitinib. This approach was utilized for measuring sunitinib in its dosage forms and spiked plasma. After excitation at 528 nm, the quenching of fluorescence is linearly related to the concentration across the range of 0.05–0.5 μg mL⁻¹ at 550 nm in Britton–Robinson buffer (pH 4.0), with a correlation value of 0.9999 and a high level of sensitivity with detection limit down to 10 ng mL⁻¹. Method II relies on spectrophotometric measurements of the produced complex at 550 nm across a range of 0.5–10.0 μg mL⁻¹, with good correlation value of 0.9999. This method has a detection limit down to 0.16 μg mL⁻¹. The proposed methodologies were validated according to International Conference on Harmonization (ICH) guidelines with satisfactory results. The stoichiometry of the reaction was determined through the application of Job's method, while the mechanism of quenching was investigated by employing the Stern–Volmer plot. The designated methods were used to estimate sunitinib in its capsules and in spiked human plasma. Additionally, the statistical analysis of the data revealed no substantial differences when compared to previous reported spectroscopic method. Green assessment tools provide further details about the eco-friendly nature of the methods.     

Orthophthaldehyde as a fluorescent probe for the feasible and sensitive assay of heptaminol: application to dosage forms and real human plasma

The antihypotensive drug heptaminol was determined using a spectrofluorimetric method and ortho-phthaladehyde as a fluorescence probe. The drug was mixed with the reagent in the presence of 2-mercaptoethanol and the reaction was carried out in slightly alkaline aqueous solution containing 0.1 M sodium hydroxide. The resulting product exhibited high fluorescence activity that was measured at 451 nm after excitation at 334 nm. The linearity range of the method was 5–100 ng ml⁻¹ with a lower detection limit of 1.8 ng ml⁻¹. The procedure was evaluated according to the International Council of Harmonization guidelines. The proposed method was applied to analyze the drug in pharmaceutical tablets and oral drops. In addition, the present study represents the first spectrofluorimetric method for the determination of the cited drug in real human plasma. The method provided high recovery percentages without any interference from coexisting pharmaceutical excipients or the components of human plasma.     

Applicability of fluorescamine as a fluorogenic reagent for highly sensitive fluorimetric analysis of the tyrosine kinase inhibitor (avapritinib) in pharmaceuticals and biological samples

Avapritinib (AVP) was the first precision drug to be approved by the US Food and Drug Administration (FDA) in 2020 for patients suffering from metastatic gastrointestinal stromal tumors (GISTs) and progressive systemic mastocytosis. The analysis of AVP in pharmaceutical tablets and human plasma was then carried out using a fast, efficient, sensitive, and simple fluorimetric method using a fluorescamine reagent. The procedure is based on the interaction between fluorescamine as a fluorogenic reagent and the primary aliphatic amine moiety in AVP using borate buffer solution at pH 8.8. The produced fluorescence was measured at 465 nm (Excitation at 395 nm). The calibration graph's linearity range was discovered to be 45.00–500.0 ng mL⁻¹. Utilizing the International Council for Harmonization (ICH) and US-FDA recommendations, the research technique was validated and bioanalytically validated. The proposed approach was effectively employed for determining the stated pharmaceuticals in plasma with a high percentage of recovery ranging from 96.87 to 98.09 and pharmaceutical formulations with a percentage of recovery equal to 102.11% ± 1.05%. In addition, the study was extended to a pharmacokinetic study of AVP with 20 human volunteers as a step for AVP management in therapeutic cancer centers.     

Use of Hantzsch reaction for quantitation of milnacipran as a magic treatment for fibromyalgia syndrome in human plasma and urine

A new fluorimetric procedure is described for analysis of milnacipran in its bulk, tablet dosage forms, as well as in biological human samples such as plasma and urine. The suggested method relies on the construction of a derivative with strong fluorescence called dihydropyridine derivative. This derivative resulted from the interaction of the primary amino group in the studied drug and acetylacetone/formaldehyde in McIlvaine buffer (pH 5). The fluorescent dihydropyridine derivative was measured at 470 nm. Influences of experimental variables namely pH, reagent concentration and temperature were examined and optimized. The calibration curve showed linearity over the range of 0.15–1.25 μg ml^?1 of milnacipran with an R² value of 0.9998. The detection limit was 0.02 μg ml^?1 and the determination limit was 0.07 μg ml^?1. The developed procedure was successfully used in the assay of the studied drug in Avermilan® tablets with excellent selectivity. In addition, the reaction was applied to estimate the drug in spiked human plasma and urine with mean percentage recoveries of 100.04 ± 1.61 and 99.78 ± 0.81% for urine and plasma, respectively.     

Influence of stearic acids on resveratrol-HSA interaction

The interaction between the natural polyphenol resveratrol and human serum albumin (HSA), the most abundant transport protein in plasma, has been studied in the absence and in the presence of up to six molecules of stearic acids (SA) pre-complexed with the protein. The study has been carried out by using the intrinsic fluorescence of both HSA and resveratrol. Protein and polyphenol fluorescence data indicate that resveratrol binds to HSA with an association constant k _a ?=?(1.10?±?0.14)?×?10⁵?M^?1 and (1.09?±?0.02)?×?10⁵?M^?1, respectively, whereas Job plot evidences the formation of an equimolar protein/drug complex. Low SA content associated with HSA does not affect significantly the structural conformation of the protein and its interaction with resveratrol, whereas high SA content induces conformational changes in the protein, and reduces resveratrol binding affinity. The photostability of resveratrol in the different samples changes in the order: buffer <?(high [SA]/HSA)?<?HSA?<?(low [SA]/HSA). The results on (SA/HSA)-resveratrol samples highlight the ability of the protein to bind hydrophobic and amphiphilic ligands and to protect from degradation an important antioxidant molecule under biologically relevant conditions.