The maintaining of constant soil moisture levels (lower than maximum capillary capacity) in pot experiments

The “injection method” is recommended for maintaining a constant soil moisture at values lower than maximum capillary capacity in pot experiments. The appropriate amount of water is injected into the soil by means of a puncture needle connected with a syringe. The reliability of the above method in relation to the uniformity of the vertical and horizontal distribution of soil moisture was tested in pot experiments with maize. The fortuity of the changes in the soil moisture distribution within the scope of the given variability restricts the “growth of roots towards the water”.     

Trypanosoma congolense: drug resistance during cyclical transmissions in tsetse flies and syringe passages in mice

A drug-resistant Trypanosoma congolense strain with predetermined curative doses (CD50 and CD90) of samorin at 13.9 +/- 1.02 and 20.3 +/- 1.13 mg/kg body weight, respectively, was cyclically transmitted through tsetse flies and by syringe passages in mice in the absence of drug pressure. The changing levels of drug sensitivity were determined after every 3rd cyclic and 5th syringe passage intervals. It was noted that when the strain was maintained in tsetse flies through 12 cyclical transmissions, the CD50 and CD90 dropped slightly from 13.9 to 11.9 +/- 1.06 and from 20.3 to 18.0 +/- 1.08 mg/kg body weight, respectively. This decrease in the level of resistance was not significant (P greater than 0.05). However, when the trypanosomes were maintained by syringe passages in mice, there was a significant reduction (P less than 0.05) in the degree of resistance (CD50 from 13.9 to 11.4 +/- 1.07 and CD90 from 20.3 to 16.7 +/- 1.16 mg/kg), by the 15th syringe passage.     

A new photometric method for oxygen consumption measurements in cell suspensions

A new technique is described for measuring O2 consumption rates and O2 concentrations in suspensions of respiring cells. Aliquots of a cell suspension kept in a special thermostated precision syringe are injected into the measuring system in defined time intervals. The O2 content of these samples is determined photometrically, as reported previously. The O2 consumption per cellular wet weight and/or per single cell can be calculated from the cell volume fraction, the physical density, the cell concentration in the suspension, and the time-dependent decline of the O2 concentration in the precision syringe. The minimum detectable amount of O2 is 0.1 microliter O2, which corresponds to 0.001 (vol/vol) of O2 if a 100-microliters sample of suspended cells is analyzed. Reproducibility of the O2 consumption measurement is 9% of the measured value. The advantages offered by this method are the straightforward calibration in absolute terms, the short time required for one analysis (2-6 min), a high sensitivity, the simultaneous determination of overall O2 concentration and O2 consumption rates in cell suspensions, and the great variability in the application.     

New trend in sample preparation: on-line microextraction in packed syringe for liquid and gas chromatography applications. I. Determination of local anaesthetics in human plasma samples using gas chromatography-mass spectrometry

A new technique for sample preparation on-line with LC and GC-MS assays was developed. Microextraction in a packed syringe (MEPS) is a new miniaturised, solid-phase extraction technique that can be connected on-line to GC or LC without any modifications. In MEPS approximately 1mg of the solid packing material is inserted into a syringe (100-250 microl) as a plug. Sample preparation takes place on the packed bed. The bed can be coated to provide selective and suitable sampling conditions. The new method is very promising. It is very easy to use, fully automated, of low cost and rapid in comparison with previously used methods. This paper presents the development and validation of a method for microextraction in packed syringe MEPS on-line with GC-MS. Local anaesthetics in plasma samples were used as model substances. The method was validated and the standard curves were evaluated by the means of quadratic regression and weighted by inverse of the concentration: 1/x for the calibration range 5-2000 nM. The applied polymer could be used more than 100 times before the syringe was discarded. The extraction recovery was between 60 and 90%. The results showed close correlation coefficients (R>0.99) for all analytes in the calibration range studied. The accuracy of MEPS-GC-MS was between 99 and 115% and the inter-day precision (n=3 days), expressed as the relative standard deviation (R.S.D.%), was 3-10%.     

Open-Source Syringe Pump Library

This article explores a new open-source method for developing and manufacturing high-quality scientific equipment suitable for use in virtually any laboratory. A syringe pump was designed using freely available open-source computer aided design (CAD) software and manufactured using an open-source RepRap 3-D printer and readily available parts. The design, bill of materials and assembly instructions are globally available to anyone wishing to use them. Details are provided covering the use of the CAD software and the RepRap 3-D printer. The use of an open-source Rasberry Pi computer as a wireless control device is also illustrated. Performance of the syringe pump was assessed and the methods used for assessment are detailed. The cost of the entire system, including the controller and web-based control interface, is on the order of 5% or less than one would expect to pay for a commercial syringe pump having similar performance. The design should suit the needs of a given research activity requiring a syringe pump including carefully controlled dosing of reagents, pharmaceuticals, and delivery of viscous 3-D printer media among other applications.     

Microexplant isolation from Cactaceae

A method of explant isolation suitable for Cactaceae is described. Small pieces of tissue were removed with a syringe without causing substantial plant injury. Using this method callus cultures were obtained in several Cactaceae species.     

Development of Biotechnology Products in Pre-filled Syringes: Technical Considerations and Approaches

A monoclonal antibody (mAb) product development case study is presented to address some of the issues faced during developing a pre-filled syringe (PFS) product for a biotherapeutic. In particular, issues involving incompatibility with silicone oil and a stability-based approach for selection of PFS barrel and tip cap components have been discussed. Silicone spiking studies followed by exposure to agitation stress or accelerated temperature conditions were used to check for incompatibilities of the mAb with silicone oil, a necessary product contact material in PFS. In addition, screening studies to compare various closure materials as well as syringe barrel processing methods were used to select the optimum closure materials as well as the correct syringe processing method. Results indicate that the model mAb formulation used was sensitive to high levels of silicone oil especially under accelerated temperature conditions resulting in formation of protein–silicone particles in the solution for samples that were spiked with the silicone oil. Agitation stress did not have any significant impact on the quality attributes tested. Samples stored in syringe barrels that were processed with sprayed-on silicone had higher levels of subvisible particles as compared to those that were processed with the baked-on process. The tip cap comparability study resulted in one tip cap material having superior compatibility among the three that were tested. The quality attribute that was most impacted by the tip cap materials was mAb oxidation. An approach for evaluation of primary packaging components during the development of pre-filled syringe presentations for biotechnology-based compounds has been highlighted.     

A method for administration of prolonged intravenous infusion of prostacyclin (PGI2) to unanesthetized rats

Prostacyclin is short acting and chemically unstable. To study sustained effects in an intact animal, prolonged intravenous infusion may be required. The compound has adequate stability for 24 hr in pH 10.0 carbonate buffer at 0°. A “displacement syringe” is described wherein the prostacyclin solution is stored in a rubber bag inside the barrel of a 5 ml syringe. This device is placed in an ice bath. A syringe pump drives water into the barrel displacing an equal volume of solution out of the bag. Chronic venous cannulas, saddles, and flow-through swivels are used as for drug self-administration studies. A simple, inexpensive rack for use with conventional individual hanging cages is also described.     

A method for administration of prolonged intravenous infusion of prostacyclin (PGI2) to unanesthetized rats.

Prostacyclin is short acting and chemically unstable. To study sustained effects in an intact animal, prolonged intravenous infusion may be required. The compound has adequate stability for 24 hr in pH 10.0 carbonate buffer at 0 degrees. A "displacement syringe" is described wherein the prostacyclin solution is stored in a rubber bag inside the barrel of a 5 ml syringe. This device is placed in an ice bath. A syringe pump drives water into the barrel displacing an equal volume of solution out of the bag. Chronic venous cannules, saddles, and flow-through swivels are used as for drug self-administration studies. A simple, inexpensive rack for use with conventional individual hanging cages is also described.     

利用生物可降解海藻酸钙微球保护苏云金杆菌晶体与芽胞免受紫外线降解

采用基于注射挤压器的液滴形成技术制备包裹了苏云金杆菌晶体和芽胞的海藻酸钙凝胶微球.通过调节该装置的活塞重量和空气压力,获得了平均直径为20μm的微球.SDS-PAGE分析与平板菌落涂布实验表明,凝胶微球可有效减少紫外线对苏云金杆菌晶体和芽胞的损伤作用.利用小菜蛾进行的毒力生测发现,凝胶微球可有效防止紫外线引起的晶体和芽胞杀虫毒力的下降.本研究的液滴形成技术也可适用于其它微球包裹过程.     

Field Application of a Rapid Spectrophotometric Method for Determination of Persulfate in Soil

Remediation of hydrocarbon contaminated soils can be performed both in situ and ex situ using chemical oxidants such as sodium persulfate. Standard methods for quantifying persulfate require either centrifugation or prolonged settling times. An optimized soil extraction procedure was developed for persulfate involving simple water extraction using a modified disposable syringe. This allows considerable saving of time and removes the need for centrifugation. The extraction time was reduced to only 5 min compared to 15 min for the standard approach. A comparison of the two approaches demonstrated that each provides comparable results. Comparisons were made using high (93 g kg⁻¹ soil) and low (9.3 g kg⁻¹ soil) additions of sodium persulfate to a petroleum hydrocarbon-contaminated soil, as well as sand spiked with diesel. Recoveries of 95±1% and 96±10% were observed with the higher application rate in the contaminated soil and spiked sand, respectively. Corresponding recoveries of 86±5% and 117±19% were measured for the lower application rate. Results were obtained in only 25 min and the method is well suited to batch analyses. In addition, it is suitable for application in a small field laboratory or even a mobile, vehicle-based system, as it requires minimal equipment and reagents.     

A modified blow-gun syringe for remote injection of captive wildlife

A modified syringe capable of automatic injection and suitable for use with a blow-gun is described. The syringe has been used successfully with white-tailed deer (Odocoileus virginianus) under confined conditions. Desirable characteristics for blow-gun syringes are discussed.     

宇宙射线中子法在农田土壤水分监测中的适用性

近年来,宇宙射线中子法(CRNS法)逐渐被应用到农田生态条件下的土壤水分监测领域,但其在田间应用时的空间代表性和测定精度还需进一步研究。本研究在华北平原冬小麦农田开展宇宙射线中子法应用效果的评价研究,采用超快速中子适应性(URANOS)模型计算CRNS法的空间权重,对CRNS法获得的土壤含水量与实测土壤含水量进行对比,以准确估算监测空间内的蓄水量。结果表明: 通过URANOS直接模拟得到的权重分布更符合理论值,测定半径在127~139 m。CRNS法估算的土壤含水量与实测土壤含水量的决定系数达到0.64,均方根误差达到0.05 cm³·cm^-3。CRNS法所得土壤含水量对探测区域内总体水分的变化响应灵敏,测定准确度有季节性变化规律。宇宙射线中子法是一种可用于冬小麦农田的连续、可靠的区域总体水分监测方法。     

A Filter-based Surface Enhanced Raman Spectroscopic Assay for Rapid Detection of Chemical Contaminants

We demonstrate a method to fabricate highly sensitive surface-enhanced Raman spectroscopic (SERS) substrates using a filter syringe system that can be applied to the detection of various chemical contaminants. Silver nanoparticles (Ag NPs) are synthesized via reduction of silver nitrate by sodium citrate. Then the NPs are aggregated by sodium chloride to form nanoclusters that could be trapped in the pores of the filter membrane. A syringe is connected to the filter holder, with a filter membrane inside. By loading the nanoclusters into the syringe and passing through the membrane, the liquid goes through the membrane but not the nanoclusters, forming a SERS-active membrane. When testing the analyte, the liquid sample is loaded into the syringe and flowed through the Ag NPs coated membrane. The analyte binds and concentrates on the Ag NPs coated membrane. Then the membrane is detached from the filter holder, air dried and measured by a Raman instrument. Here we present the study of the volume effect of Ag NPs and sample on the detection sensitivity as well as the detection of 10 ppb ferbam and 1 ppm ampicillin using the developed assay.     

Calibration of pneumotachographs using a calibrated syringe.

Pneumotachograph require frequent calibration. Constant-flow methods allow polynomial calibration curves to be derived but are time consuming. The iterative syringe stroke technique is moderately efficient but results in discontinuous conductance arrays. This study investigated the derivation of first-, second-, and third-order polynomial calibration curves from 6 to 50 strokes of a calibration syringe. We used multiple linear regression to derive first-, second-, and third-order polynomial coefficients from two sets of 6-50 syringe strokes. In part A, peak flows did not exceed the specified linear range of the pneumotachograph, whereas flows in part B peaked at 160% of the maximum linear range. Conductance arrays were derived from the same data sets by using a published algorithm. Volume errors of the calibration strokes and of separate sets of 70 validation strokes (part A) and 140 validation strokes (part B) were calculated by using the polynomials and conductance arrays. Second- and third-order polynomials derived from 10 calibration strokes achieved volume variability equal to or better than conductance arrays derived from 50 strokes. We found that evaluation of conductance arrays using the calibration syringe strokes yields falsely low volume variances. We conclude that accurate polynomial curves can be derived from as few as 10 syringe strokes, and the new polynomial calibration method is substantially more time efficient than previously published conductance methods.     

Critical evaluation of sampling techniques for residual glucose determination in carbon-limited chemostat culture of Saccharomyces cerevisiae

In this paper, three sampling techniques for rapid quenching of cellular metabolism and subsequent separation of cells from fermentation broth are compared: (i) quick freezing of fermentation broth directly in liquid nitrogen; (ii) quenching metabolism by exposing the fermentation broth to stainless steel beads (4-mm diameter) in a filter syringe precooled to -18 degrees C; and (iii) withdrawal of the filtrate through a 0.45 microm filter attached to a syringe and a needle inserted directly into the fermentor. It was concluded that use of liquid nitrogen as a quenching method to rapidly arrest cellular metabolism, for quantitative analysis of extracellular glucose, is not a very reliable method and that the filter syringe steel beads work very well.     

CULTIVATION OF A FILAMENTOUS ALGA IN QUANTITY ON AGAR PLATES1,2

A method for the cultivation of Zygnema in quantity on agar plates is described. Axenic filaments were chopped with razor blades, and 4 ml of the suspension of short filaments in nutrient medium were transferred with a syringe to 1% agarized nutrient medium plates. Filamentous growth uniformly covered agar plates in 10 days or less.     

Syringe method for stepwise chemical synthesis of oligonucleotides.

A simple procedure is described for synthesis of oligonucleotides by phosphate chemistry. Chains can be constructed rapidly with minimal equipment (a syringe and reagent bottles). The method is illustrated by synthesis of d-TGCAGGTT. Pertinent supporting data on the effect of variations in the detritylation, condensation, oxidation, capping and cleavage steps in the synthetic approach and in isolation procedures are also presented.     

Rapid method for direct extraction of DNA from soil and sediments.

A rapid method for the direct extraction of DNA from soil and sediments was developed. The indigenous microorganisms in the soil and sediments were lysed by using lysozyme and a freeze-thaw procedure. The lysate was extracted with sodium dodecyl sulfate and phenol-chloroform. In addition to a high recovery efficiency (greater than 90%), the yields of DNA were high (38 and 12 micrograms/g [wet weight] from sediments and soil, respectively). This method generated minimal shearing of the extracted DNA. The crude DNA could be further purified with an Elutip-d column if necessary. An additional advantage of this method is that only 1 g of sample is required, which allows for the analysis of small samples and the processing of many samples in a relatively short (7 h) period.     

Nonaspiration fine needle cytology. Application of a new technique to nodular thyroid disease

The basic principle underlying fine needle aspiration (FNA) is the aspiration of cellular material from target masses, often utilizing fairly high suction pressures. The procedure requires a needle and a syringe, advisedly held in a syringe holder, enabling single-handed suction to be exercised. Mastery of the technique is variable, with few operators acquiring consistent skill. A new technique, pioneered in France but essentially unpublicized, eliminates active aspiration, replacing it by the principle of capillary suction of fluid or semifluid material into a thin channel (a fine needle). This nonaspiration sampling method was tested in a consecutive series of 50 solid thyroid nodules. Simultaneously performed conventional FNAs served as controls. Cell samples were cytologically assessed as unsuitable, diagnostic/adequate or diagnostic/superior, without knowledge of the sampling method employed. Diagnostically superior specimens were obtained significantly more frequently by the nonaspiration technique in 36 benign lesions and 13 neoplasms. The method of nonaspiration fine needle cytology ("cytopuncture") is described and illustrated, and the implications for its use in other sites are discussed.