Non-labeled detection of waterborne pathogen Cryptosporidium parvum using a polydiacetylene-based fluorescence chip

A non-labeling fluorescence sensor system was developed using polydiacetylene (PDA) liposomes composed of 10,12-pentacosadiynoic acid (PCDA) and 1,2-dimyristoyl-sn-glycero-3-phosphocholine (DMPC) at a 8:2 molar ratio. The PDA liposomes were immobilized onto an amine-coated glass surface using peptide bonding between the carboxyl group of the liposome and the amine group of the glass surface. The optimum ratio of the cross linker (NHS/EDC) to PDA liposome was determined to be 50% for strong immobilization of the liposomes. Residual carboxyl groups of the PDA liposomes were selectively biotinylated, followed by sequential binding of streptavidin and biotin-antibody (bioreceptor). Finally, the performance of the PDA liposome chip was tested for detecting Cryptosporidium parvum, and yielded a detection limit of 1 x 10(3) oocysts/mL. From these results, it is expected that the PDA liposome chip will have high application potential for the detection of waterborne pathogens including C. parvum.     

DNA microdevice for electrochemical detection of Escherichia coli 0157:H7 molecular markers

An electrochemical DNA sensor based on the hybridization recognition of a single-stranded DNA (ssDNA) probe immobilized onto a gold electrode to its complementary ssDNA is presented. The DNA probe is bound on gold surface electrode by using self-assembled monolayer (SAM) technology. An optimized mixed SAM with a blocking molecule preventing the nonspecific adsorption on the electrode surface has been prepared. In this paper, a DNA biosensor is designed by means of the immobilization of a single stranded DNA probe on an electrochemical transducer surface to recognize specifically Escherichia coli (E. coli) 0157:H7 complementary target DNA sequence via cyclic voltammetry experiments. The 21 mer DNA probe including a C6 alkanethiol group at the 5' phosphate end has been synthesized to form the SAM onto the gold surface through the gold sulfur bond. The goal of this paper has been to design, characterise and optimise an electrochemical DNA sensor. In order to investigate the oligonucleotide probe immobilization and the hybridization detection, experiments with different concentration of DNA and mismatch sequences have been performed. This microdevice has demonstrated the suitability of oligonucleotide Self-assembled monolayers (SAMs) on gold as immobilization method. The DNA probes deposited on gold surface have been functional and able to detect changes in bases sequence in a 21-mer oligonucleotide.     

Colorimetric Detection of Some Highly Hydrophobic Flavonoids Using Polydiacetylene Liposomes Containing Pentacosa-10,12-diynoyl Succinoglycan Monomers

Flavonoids are a group of plant secondary metabolites including polyphenolic molecules, and they are well known for antioxidant, anti-allergic, anti-inflammatory and anti-viral propertied. In general, flavonoids are detected with various non-colorimetric detection methods such as column liquid chromatography, thin-layer chromatography, and electrochemical analysis. For the first time, we developed a straightforward colorimetric detection system allowing recognition of some highly hydrophobic flavonoids such as alpha-naphthoflavone and beta-naphthoflavone, visually using 10,12-pentacosadiynoic acid (PCDA) derivatized with succinoglycan monomers isolated from Sinorhizobium meliloti. Besides changes in visible spectrum, we also demonstrate fluorescence changes using our detection system in the presence of those flavonoids. The succinoglycan monomers attached to PCDA molecules may function as an unstructured molecular capturer for some highly hydrophobic flavonoids by hydrophobic interactions, and transmit their molecular interactions as a color change throughout the PCDA liposome.     

Optical detection of DNA hybridization based on fluorescence quenching of tagged oligonucleotide probes by gold nanoparticles

A novel system for the detection of DNA hybridization in a homogeneous format is developed. This method is based on fluorescence quenching by gold nanoparticles used as both nanoscaffolds for the immobilization of capture sequences and nanoquenchers of fluorophores attached to detection sequences. The oligonucleotide-functionalized gold nanoparticles are synthesized by derivatizing the colloidal gold solution with 5'-thiolated 12-base oligonucleotides. Introduction of sequence-specific target DNAs (24 bases) into the mixture containing dye-tagged detection sequences and oligonucleotide-functionalized gold nanoparticles results in the quenching of carboxytetramethylrhodamine-labeled DNA fluorescence because DNA hybridization occurs and brings fluorophores into close proximity with oligonucleotide-functionalized gold nanoparticles. The quenching efficiency of fluorescence increases with the target DNA concentration and provides a quantitative measurement of sequence-specific DNA in sample. A linearity is obtained within the range from 1.4 to 92 nM. The target sequence is detected down to 2 nM. This new system not only overcomes many of the drawbacks inherent in radioisotopic measurement or enzyme-linked assay but also avoids the requirement for the stem-loop structure compared with conventional molecular beacons. Furthermore, the background signal that is defined as fluorescence quenching arising from electrostatic attraction between positively charged fluorophores and negatively charged gold nanoparticles is comparatively low due to electrostatic repulsion between negatively charged oligonucleotides. In addition, this is a homogeneous assay that can offer the potential to be monitored in real time, be amenable to automation, eliminate washing steps, and reduce the risk of contamination.     

Polydiacetylene (PDA)-based colorimetric detection of biotin-streptavidin interactions

The natural binding of streptavidin (STA) for a small molecule, biotin, has made it a useful tool in specific targeting application, due to their most specific noncovalent biological interactions in nature. Here, we describe a polydiacetylene (PDA)-based colorimetric biosensor to detect the STA-biotin interactions. We synthesized two kinds of biotin-labeled 10,12-pentacosadiynoic acid (PCDA) monomers having 2(ethylene oxide) or 3(ethylene oxide) spacer and prepared biotin-modified PDA liposomes using them. Upon the addition of STA, the modified PDA liposomes showed a color change from blue to red in about 1h followed by their aggregation and precipitation. The aggregation was found to be due to the cross-linking between the PDA liposomes caused by the STA having four biotin binding sites, which was confirmed by their TEM analysis. Since the STA-biotin interactions are widely adopted for various biological detection systems; the biotin-modified PDA sensor developed in this study has enormous potentials for the development of various colorimetric biosensors.     

Enhancement of DNA immobilization and hybridization on gold electrode modified by nanogold aggregates

Gold electrodes modified by nanogold aggregates (nanogold electrode) were obtained by the electrodeposition of gold nanoparticles onto planar gold electrode. The Electrochemical response of single-stranded DNA (ssDNA) probe immobilization and hybridization with target DNA was measured by cyclic voltammograms (CV) using methylene blue (MB) as an electroactive indicator. An improving method using long sequence target DNA, which greatly enhanced the response signal during hybridization, was studied. Nanogold electrodes could largely increase the immobilization amount of ssDNA probe. The hybridization amount of target DNA could be increased several times for the manifold nanogold electrodes. The detection limit of nanogold electrode for the complementary 16-mer oligonucleotide (target DNA1) and long sequence 55-mer oligonucleotide (target DNA2) could reach the concentration of 10(-9) mol/L and 10(-11) mol/L, respectively, which are far more sensitive than that of the planar electrode.     

Morphological studies of oligodeoxyribonucleotides probes covalently immobilized at polystyrene modified surfaces

The immobilization of short ss-DNA (18- and 36-mer) and their hybridization were studied at gold and glassy carbon substrates modified with low molecular weight (approximately 12, 18 and 24 kg/mol) polystyrene thin films. Amino-modified DNA was attached to the surface by reaction with succinimide ester groups bound to the polystyrenes. A ferrocene modified DNA target was used to confirm the probe-target hybridization. Atomic force microscopy studies showed significant morphological changes after probe immobilization and hybridization compared to the featureless structure of the polystyrene film. Single-stranded DNA samples had a globular morphology with an average density of 3.8 and 2.2 (x 10(11)) globules/cm2 for the 18- and 36-mer, respectively. The formation of a porous structure with a 2.0 and 1.0 (x10(11)) average pore density corresponding to the 18- and 36-mer was observed after hybridization. A surface composition analysis was done by X-ray photoelectron spectroscopy to confirm and support the images interpretation. Ferrocene oxidation (+323 mV/18-mer, +367 mV/36-mer, versus Ag/AgCl) proved the presence of ds-DNA at the modified surfaces.     

Optimization of DNA immobilization on gold electrodes for label-free detection by electrochemical impedance spectroscopy

The ability to immobilize DNA probes onto gold substrates at an optimum surface density is key in the development of a wide range of DNA biosensors. We present a method to accurately control probe DNA surface density by the simultaneous co-immobilization of thiol modified probes and mercaptohexanol. Probe surface density is controlled by the thiol molar ratio in solution, with a linear relationship between thiol molar ratio and probe density spanning (1-9) x10(12)/cm2. The probe surface density per microscopic surface area was determined using chronocoulometry, and a detailed analysis of the method presented. Using this sample preparation method, the effect of probe density and hybridization on the charge transfer resistance with the negatively charged ferri/ferrocyanide redox couple was determined. Above a threshold probe surface density of 2.5 x 10(12)/cm2, electrostatic repulsion from the negatively charged DNA modulates the charge transfer resistance, allowing hybridization to be detected. Below the threshold density no change in charge transfer resistance with probe density or with hybridization occurs. The probe surface density was optimized to obtain the maximum percentage change in charge transfer resistance with hybridization.     

Oligonucleotide quartz crystal microbalance sensor for the microalgae Alexandrium minutum (Dinophyceae)

We report the immobilization on a gold surface of a 20-base DNA probe labeled with disulfide group and on the selective hybridization with the complementary 20-base DNA strand. The oligonucleotide probe is the complementary strand of a partial sequence of the gene encoding for a large ribosomal RNA sub-unit which is a coding sequence of Alexandrium minutum DNA, a microalgae that produces neurotoxins responsible for paralytic shellfish poisoning on European and Asian coasts. The kinetics of DNA probe immobilization and hybridization were monitored in situ by using a 27 MHz quartz crystal microbalance under controlled hydrodynamic conditions. The frequency of the setup is stable to within a few hertz, corresponding to the nanogram scale, for 3h and makes it possible to follow frequency change from immobilization of the probe to hybridization of the complementary DNA target. This setup constitutes a biosensor, which is sensitive and selective, and the hybridization ratio between hybridized complementary DNA and immobilized DNA probes is 47%.     

QCM-based DNA biosensor for detection of genetically modified organisms (GMOs)

Development of a mass sensitive quartz crystal microbalance (QCM)-based DNA biosensor for the detection of the hybridization of CaMV 35S promoter sequence (P35S) was investigated for the screening of genetically modified organisms (GMOs). Attention was focused on the choice of the coating chemistry that could be used for the immobilization of probe sequences on the gold surface of the quartz crystal. Two immobilization procedures were tested and compared considering the amount of the immobilized P35S probe and the extent of the hybridization reaction with the target oligonucleotide. In wet chemistry procedure, the interaction between the thiol and gold for the immobilization of a thiolated probe was employed. Direct surface functionalization of piezoelectric quartz crystals were achieved in 13.56 MHz plasma polymerization reactor utilising ethylenediamine (EDA) precursors for the immobilization of amined probes. Results indicated that immobilization of a thiolated probe provides better immobilization characteristics and higher sensitivity for the detection of the hybridization reaction. The thiolated probe was used for the detection of P35S sequence in PCR-amplified DNAs and in real samples of pflp (ferrodoxin like protein)-gene inserted tobacco plants. Fragmentation of the genomic DNAs were achieved by digestion with restriction endonucleases and ultrasonication. The results obtained from the fragmented genomic DNAs demonstrated that it is possible to detect the target sequence directly in non-amplified genomic DNAs by using the developed QCM-based DNA biosensor system. The developed QCM-based DNA biosensor represented promising results for a real-time, label-free, direct detection of DNA samples for the screening of GMOs.     

Immobilization of DNA on microporous membranes using UV-irradiation]

Various techniques of DNA immobilization onto nitrocellulose and nylon microporous membranes have been compared. Despite a strong primary adsorption of DNA onto these membranes during blotting procedures, poor retention of the target DNA and low hybridization signals are obtained after hybridization and washings. Covalent cross-linking of DNA upon UV irradiation leads to a quantitative immobilization of target DNA. Quantum yield of DNA photoimmobilization estimated for a single base in DNA is about 10(-4). UV irradiation dose sufficient for immobilization of DNA fragment of a known length can be calculated by the formula Ilc = (22.3 +/- 4.8) c/l, where l is the DNA fragment length (in base pairs), c is the DNA part (%) to be immobilized. The UV irradiation dose about 0.6-0.8 kJ/m2 is optimal for most hybridization experiments. Doses higher than 0.8-1 kJ/m2 may cause a loss in the hybridization efficiency. Under optimal immobilization conditions, hybridization signals increasing five-fold for nitrocellulose membranes and fifty-fold for uncharged nylon membranes as compared with baking these membranes in vacuum.     

Hybridization biosensor using di(2,2'-bipyridine)osmium (III) as electrochemical indicator for detection of polymerase chain reaction product of hepatitis B virus DNA

A novel hepatitis B virus (HBV) DNA biosensor was developed by immobilizing covalently single-stranded HBV DNA fragments to a gold electrode surface via carboxylate ester to link the 3(')-hydroxy end of the DNA with the carboxyl of the thioglycolic acid (TGA) monolayer. A short-stranded HBV DNA fragment (181bp) of known sequence was obtained and amplified by PCR. The surface hybridization of the immobilized single-stranded HBV DNA fragment with its complementary DNA fragment was evidenced by electrochemical methods using [Os(bpy)(2)Cl(2)](+) as a novel electroactive indicator. The formation of double-stranded HBV DNA on the gold electrode resulted in a great increase in the peak currents of [Os(bpy)(2)Cl(2)](+) in comparison with those obtained at a bare or single-stranded HBV DNA-modified electrode. The mismatching experiment indicated that the surface hybridization was specific. The difference between the responses of [Os(bpy)(2)Cl(2)](+) at single-stranded and double-stranded DNA/TGA gold electrodes suggested that the label-free hybridization biosensor could be conveniently used to monitor DNA hybridization with a high sensitivity. X-ray photoelectron spectrometry technique has been employed to characterize the immobilization of single-stranded HBV DNA on a gold surface.     

Independently-addressable micron-sized biosensor elements

With the continuing development of micro-total analysis systems and sensitive biosensing technologies, it is often desirable to immobilize biomolecules onto a surface in a small well-defined area. A novel method was developed to electrochemically attach DNA probes to micron-sized regions of a gold surface using biotin-LC-hydrazide (BH). Previously, we have found that the radical produced during the oxidation of BH will attach to a wide variety of electroactive surfaces. An array of micron-sized gold band electrodes (75 microm wide) was fabricated onto glass microscope slides and BH was deposited onto each electrode through the application of an oxidizing potential. Subsequent attachment of avidin to the biotinylated surface created the 'molecular sandwich' architecture necessary for further immobilization of biotinylated biomolecules to the surface. In this work, we utilized biotinylated DNA probes of varying sequence to illustrate the specificity of the attachment scheme. The immobilization of avidin, DNA probe, and hybridization of DNA target is visualized with fluorescence tags and the spatially selective attachment and hybridization of unique DNA sequences is demonstrated.     

Introduction of hematoxylin as an electroactive label for DNA biosensors and its employment in detection of target DNA sequence and single-base mismatch in human papilloma virus corresponding to oligonucleotide

For the detection of DNA hybridization, a new electrochemical biosensor was developed on the basis of the interaction of hematoxylin with 20-mer deoxyoligonucleotides (from human papilloma virus, HPV). The study was performed based on the interaction of hematoxylin with an alkanethiol DNA probe self-assembled gold electrode (ss-DNA/AuE) and its hybridization form (ds-DNA/AuE). The optimum conditions were found for the immobilization of HPV probe on the gold electrode (AuE) surface and its hybridization with the target DNA. Electrochemical detection of the self-assembled DNA and the hybridization process were performed by cyclic voltammetry (CV) and differential pulse voltammetry (DPV) over the potential range where the accumulated hematoxylin at the modified electrode was electroactive. Observing a remarkable difference between the voltammetric signals of the hematoxylin obtained from different hybridization samples (non-complementary, mismatch and complementary DNAs), we confirmed the potential of the developed biosensor in detecting and discriminating the target complementary DNA from non-complementary and mismatch oligonucleotides. Under optimum conditions, the electrochemical signal had a linear relationship with the concentration of the target DNA ranging from 12.5 nM to 350.0 nM, and the detection limit was 3.8 nM.     

Self-assembly DNA-conjugated polymer for detection of single nucleotide polymorphism

We developed a self-assembly DNA-conjugated polymer based on polyacrylic acid (PAA) for DNA chip fabrication. A 20-mer single-stranded DNA (ssDNA, probe-1), and 3-(2-pyridyldithio)propionyl hydrazide (PDPH), for promoting self-assembled immobilization, were both covalently attached to PAA as sidechains. This DNA-conjugated PAA was then spontaneously immobilized on a gold substrate. Probe-1 on the immobilized polymer was hybridized to a 34-mer ssDNA (probe-2), which had the sequence desired for analyzing the target DNA. The fluorescence intensity after incubating the P-1 DNA-conjugated polymer with probe-2 DNA was much higher than with control sequence in the first hybridization. The interactions between target DNA and the DNA-conjugated PAA were investigated by fluorescence measurement. The interaction of fully matched target DNA with this immobilized DNA conjugated polymer has been studied at different ion strength conditions. SNP sequences as targets showed less than 15% the intensity of fully matched target DNA in the second hybridization, indicating that the gold surfaces coated with the DNA-conjugated PAA was highly specific to fully matched DNA. The DNA-conjugated PAA immobilized on a gold substrate is characterized by reduced nonspecific adsorption, due to less electrostatic repulsion as well as the polymer coating. Therefore, DNA-conjugated PAA can be used for probe DNA immobilization method.     

Molecular recognition of concanavalin A on mannoside diacetylene lipid monolayer at the air-water interface.

The interaction of p-10,12-pentacosadiyne-1-n-phenylamide alpha-D-mannopyranoside (MPDA) with protein concanavalin A (Con A) was studied at the air/water interface. The expansion of molecular area of PDA (10,12-pentacosadiynoic acid)/MPDA mixed monolayer after injection of Con A in subphase shows strong interaction between Con A and the monolayer. The maximum expansion of molecular area decreases as the molar ratio of MPDA increases due to the steric hindrance effect. By using enzyme mannosidase to cut-off the mannoside headgroup of MPDA, expansion of molecular area was greatly reduced, indicating that the binding of Con A is specific to the mannoside headgroup. The kinetics of the binding fits to the first order bimolecular reaction model. Fluorescence quenching of fluorescein isothiocyanate labeled Con A after injection into the subphase gives a direct proof of the molecular recognition.     

Electrochemical synthesis of gold nanostructure modified electrode and its development in electrochemical DNA biosensor

In this article, gold nanostructure modified electrodes were achieved by a simple one-step electrodeposition method. The morphologies of modified electrodes could be easily controlled by changing the pH of HAuCl₄ solution. The novel nanoflower-like particles with the nanoplates as the building blocks could be interestingly obtained at pH 5.0. The gold nanoflower modified electrodes were then used for the fabrication of electrochemical DNA biosensor. The DNA biosensor fabrication process was characterized by cyclic voltammetry and electrochemical impedance spectroscopy with the use of ferricyanide as an electrochemical redox indicator. The DNA immobilization and hybridization on gold nanoflower modified electrode was studied with the use of [Ru(NH₃)₆]³⁺ as a hybridization indicator. The electrochemical DNA biosensor shows a good selectivity and sensitivity toward the detection of target DNA. A detection limit of 1 pM toward target DNA could be obtained.     

Green-synthesized gold nanoparticles decorated graphene sheets for label-free electrochemical impedance DNA hybridization biosensing

Sensitive electrochemical impedance assay of DNA hybridization by using a novel graphene sheets platform was achieved. The graphene sheets were firstly functionalized with 3,4,9,10-perylene tetracarboxylic acid (PTCA). PTCA molecules separated graphene sheets efficiently and introduced more negatively-charged -COOH sites, both of which were beneficial to the decoration of graphene with gold nanoparticles. Then amine-terminated ionic liquid (NH?-IL) was applied to the reduction of HAuCl? to gold nanoparticles. The green-synthesized gold nanoparticles, with the mean diameter of 3 nm, dispersed uniformly on graphene sheets and its outer layer was positively charged imidazole termini. Due to the presence of large graphene sheets and NH?-IL protected gold nanoparticles, DNA probes could be immobilized via electrostatic interaction and adsorption effect. Electrochemical impedance value increased after DNA probes immobilization and hybridization, which was adopted as the signal for label-free DNA hybridization detection. Unlike previously anchoring DNA to gold nanoparticles, this label-free method was simple and noninvasive. The conserved sequence of the pol gene of human immunodeficiency virus 1 was satisfactorily detected via this strategy.     

Immobilization and hybridization by single sub-millisecond electric field pulses, for pixel-addressed DNA microarrays

Single square voltage pulses applied to buried electrodes result in dramatic rate increases for (1) selective covalent bonding (immobilization) of single-stranded DNA (ssDNA) probes to a functionalized thin film SiO₂ surface on a plastic substrate and (2) hybridization of ssDNA to the immobilized probe. DNA immobilization and hybridization times are 100 ns and 10 μs, respectively, about 10⁹ times faster than the corresponding passive reactions without electric field. Surface coverage is comparable. Duration, magnitude and slew rate of the voltage pulse are all key factors controlling the rates of ssDNA immobilization and hybridization. With rise times of 4.5 ns, pulses shorter than 1 ms and voltages below 1 V are effective. The ssDNA adsorbed on the surface is reoriented by the rapidly changing electric field. This reduces steric barriers and speeds the immobilization and hybridization reactions. These results open the way for pixel-addressed microarrays driven by silicon microelectronics circuits.     

Investigation of DNA orientation on gold by EC-STM.

The immobilization of thiol-derivatized DNA on a Au (111) single crystal surface by self-assembly has been investigated by electrochemical scanning tunneling microscopy (EC-STM). Continuous potential-dependent orientation changes of double-stranded oligodeoxynucleotides (ODN) have been observed in a certain potential range from 200 to 600 mV (versus SCE). It is suggested that the DNA duplexes stand straight on the gold surface at potentials negative of the potential of zero charge (pzc) and then lay down on the surface when the potential shifts positively. These results are in agreement with the expectation based on the Coulombic interaction consideration between negatively charged DNA helices and gold surface. As the applied potential shifts positively, the surface charge changes from negative to positive, that is, the Coulombic force between negatively charged DNA helices and gold surfaces changes from repulsion to attraction. However, for the single-stranded oligodeoxynucleotides, no distinct changes in the surface structure were observed with the applied potential.