SiC Multilayer Structures as Light Controlled Photonic Active Filters

Tunable wavelength division multiplexing converters based on amorphous SiC multilayer photonic active filters are analyzed. The configuration includes two stacked p-i-n structures (p(a-SiC:H)-í'(a-SiC:H)-n(a-SiC:H)-p(a-SiC:H)-i(a-Si:H)-n(a-Si:H)) sandwiched between two transparent contacts. The manipulation of the magnitude is achieved through appropriated front and back backgrounds. Transfer function characteristics are studied both theoretically and experimentally. An algorithm to decode the multiplex signal is established. An optoelectronic model supports the optoelectronic logic architecture. Results show that the light-activated device combines the demultiplexing operation with the simultaneous photodetection and self-amplification of an optical signal. The output waveform presents a nonlinear amplitude-dependent response to the wavelengths of the input channels. Depending on the wavelength of the external background and irradiation side, it acts either as a short- or a long-pass band filter or as a band-stop filter. A two-stage active circuit is presented and gives insight into the physics of the device.     

Optical Filter Design Using Background Wavelength Processing Techniques

Amorphous SiC tandem heterostructures are used to filter a specific band, in the visible range. Experimental and simulated results are compared to validate the use of SiC multilayered structures in applications where gain compensation is needed or to attenuate unwanted wavelengths. Spectral response data acquired under different frequencies, optical wavelength control and side irradiations are analyzed. Transfer function characteristics are discussed. Color pulsed communication channels are transmitted together and the output signal analyzed under different background conditions. Results show that under controlled wavelength backgrounds, the device sensitivity is enhanced in a precise wavelength range and quenched in the others, tuning or suppressing a specific band. Depending on the background wavelength and irradiation side, the device acts either as a long-, a short-, or a band-rejection pass filter. An optoelectronic model supports the experimental results and gives insight on the physics of the device.     

Further improvements to the photoelectric method for measuring motile responses of chromatophores

With the intention of simplifying construction and operation, improvements have now been made to a photoelectric system for measuring the motile responses of chromatophores. Introduction of chop-per-stabilized operational amplifiers with a complimentary metal-oxide semiconductor (C-MOS) input has brought about a much improved stability of the electronics. Such a feature has been found to be especially suitable for measurements requiring higher amplification and longer periods of time, e.g., the detection of the effects of various factors on bright-colored chromatophores. The use of appropriate color filters that limit the spectral range of light used for measurement has also proven to be important. By installing a small filter close to the photosensor, we can now record the responses of particular types of chromatophores more selectively, while visually monitoring the states of all kinds of chromatophores in natural color. To minimize the influence of motile activities of xanthophores and/or erythrophores, the use of an orange-to-red long-pass filter is appropriate to optimize recording the melanophore responses. By contrast, the responses of xanthophores or erythrophores can be recorded more easily by employing a violet-to-blue band-pass filter, because that increases the contrast of images of these cells against the background. Using an orange-red variety of the medaka Oryzias, we have also recorded photometrically the responses of leucophores, whose organelles are light-scattering. A long-pass filter was efficient in excluding the influences of co-existing xanthophores.     

High-performance optical filters for fluorescence analysis

Recent advances in thin film optical coating technology significantly improve the filters available for fluorescence spectroscopy. Bandpass and long- and shortpass filters with very sharply defined edges can provide from 10(-5) to 10(-6) blocking within 10-15 nm of the transmission region and are ideal for use as excitation and emission filters. A variety of nonpolarizing dichroic beamsplitters for use in epi-illumination configurations or in multiple emission configurations provides optimum longpass, shortpass, band reflection, or bandpass spectral control. These dichroics, used with high-performance bandpass, longpass, or shortpass filters, form matched sets that optimize the signal-to-noise ratio and system efficiency for fluorescence spectroscopic systems in single or multiple dye applications. Specially designed dichroic beamsplitters are used to reduce excitation filter overheating. Other dichroic beamsplitters efficiently separate two planes of polarization in a narrow wavelength band. Rejection band filters can be used to measure the fluorescent dye Indo 1 with very low emission signals.     

声光可调谐滤波器的细胞生物学研究应用

波长选择在荧光光谱仪和显微镜等光学应用中发挥了至关重要的作用。声光可调谐滤波器(AOTF)作为一种电光器件可实现多光源入射波长、功率的同时调制。在声光可调谐滤波器中,压电换能器结合于二氧化碲或石英晶体产生高频声波,改变晶体折射率形成周期性分布。该现象在晶体中生成衍射光栅,使以布拉格角正交入射的光束被高效衍射至一阶光束。当改变施加到晶体的信号频率时将改变折射率变化周期,因此,衍射光的波长随之改变。同时,衍射光强度由施加到晶体的信号振幅决定。本文从声光可调谐滤波器原理和特点出发,总结了声光可调谐滤波器在细胞生物学研究系统中的应用模型。得益于作用时间短、波长分辨率高、无振动部件等特性,声光可调谐滤波器提升了多波长光源功率调制能力,使细胞计数系统具备了细胞高光谱成像能力。所以不仅限于传统细胞生物学研究,包含声光可调谐滤波器件的系统还将在多参数高内涵成像分析、扫描荧光显微术、药物毒理研究等领域成为有力的研究工具。     

Ratiometric pH measurements using LysoSensor DND-192

A method for the ratiometric pH sensing using LysoSensor DND-192 is presented in this paper. It works in the physiological pH range. It is based on the use of two fluorophores which differ significantly in their lifetimes. As the discrimination of their emissions is performed through two different frequencies, this method can allow significant overlap of the emission spectra. A simple long-pass filter, or a combination of long- and short-pass filters, was used instead of narrow-bandpass devices. Importantly, the measurements were carried out under strong ambient light. The method could be used in a wide variety of applications, such as intracellular measurements, microscopy, bioprocess monitoring, etc.     

Optical Channel Drop Filter Design Based on PCRR and Micro Cavity Resonator

Optical channel drop filter (OCDF) plays a key role in optical communication networks for filtering the individual wavelength among the group of channels in wavelength division multiplexing systems. There are several channel drop filters with different design mechanisms available in the literature, but those structure dimensions are not compact enough for the photonic integrated applications. Hence, in this paper, a compact and efficient OCDF is developed in the triangular lattice PC structure based on diamond-shaped photonic crystal ring resonator (PCRR) mechanism combined with micro cavity resonator (MCR). The developed OCDF is analysed for different operating wavelengths by considering the different positions of MCR around the main PCRR. Based upon the position of the MCR around PCRR, the three dropping wavelengths such as 1540 nm, 1550 nm, and 1570 nm are observed at the output waveguides with 100% dropping efficiency. Then the structural and performance parameter comparison is done between the proposed and existing structures in terms of device dimension, dropping efficiency, and quality factor. It is depicted through the results that the quality factor and the device dimension are better than that of the existing structures for 1550-nm wavelength.

     

The importance of optical optimization in whole slide imaging (WSI) and digital pathology imaging

In the last 10 years, whole slide imaging (WSI) has seen impressive progress not only in image quality and scanning speed but also in the variety of systems available to pathologists. However, we have noticed that most systems have relatively simple optics axes and rely on software to optimize image quality and colour balance. While much can be done in software, this study examines the importance of optics, in particular optical filters, in WSI.Optical resolution is a function of the wavelength of light used and the numerical aperture of the lens system (Resolution = (f) wavelength/2 NA). When illumining light is not conditioned correctly with filters, there is a tendency for the wavelength to shift to longer values (more red) because of the characteristics of the lamps in common use. Most microscopes (but remarkably few WSI devices) correct for this with ND filter for brightness and Blue filter (depends on the light source) for colour correction.Using H&E slides research microscopes (Axiophot, Carl Zeiss MicroImaging, Inc. NY. Eclipse 50i., Nikon Inc. NY) at 20x, an attached digital camera (SPOT RT741 Slider Color, Diagnosis Instruments., MI USA), and a filter set, we examined the effect of filters and software enhancement on digital image quality. The focus value (as evaluated by focus evaluation software developed in house and SPOT imaging Software v4.6) was used as a proxy for image quality. Resolution of tissue features was best with the use of both the Blue and ND filters (in addition to software enhancement). Images without filters but with software enhancement while superficially good, lacked some details of specimen morphology and were unclear compared with the images with filters.The results indicate that the appropriate use of optical filters could measurably improve the appearance and resolution of WSI images.     

A high performance micro-dual-wavelength-spectrophotometer (MDWS)

The dual wavelength spectrophotometer (DWS) has proven to be the most sensitive device to monitor minute optical absorbance changes, which are inaccessible to conventional single or double beam spectrophotometers. The typical set ups, e.g. extensively used for Ca2+ or phytochrome measurements, are huge, expensive and cumbrous. Therefore, a novel high performance micro-dual-wavelength spectrophotometer (MDWS) was developed. It is miniaturized and no moving parts such as vibrational mirrors or rotating filter wheels involved. Its specifications are superior compared to the conventional set up being capable of detecting minute optical changes (reflection, absorbance, transmittance) at particular wavelengths.     

Use of selected excitation filters for enhancement of diaminobenzidine photomicroscopy

Enhancement of the diaminobenzidine (DAB) reaction product for light photomicroscopy was investigated using commercially available glass interference filters FITC-495, BG38, and BG12. The oxidized DAB transmission curve between 400-700 nm revealed a broad peak extending mostly through the yellow to red portions of the visible light spectrum, indicating that no single color predominates. Absorption spectra from the interference filters showed that FITC-495 gave total absorbance from 495-650 nm, with a smaller peak at 675 nm; BG38 transmitted at least a percentage of every wavelength up to 700 nm, whereas BG12 absorbed all light above 490 nm. To determine whether these filters could photographically increase DAB reaction product contrast, photographs were taken of corneal endothelial cells 24 hr after freeze injury. At this time, these cells demonstrate increased levels of laminin, as revealed by immunoperoxidase cytochemistry. When photography was performed using either no filter or a standard green filter, DAB contrast relative to background was minimal. However, when photographs were made using either the FITC-495 or the BG12 filter, DAB contrast increased sharply, although background density increased in the former case and decreased greatly in the latter. BG38 by itself did not increase DAB contrast. However, when used in combination with FITC-495 good DAB contrast was achieved and background density was lower than that seen using FITC-495 alone. Therefore, selective interference filters can photographically increase DAB contrast for studies using immunoperoxidase cytochemistry.     

Multi-Band-Stop Filter for Single-Photon Transport Based on a One-Dimensional Waveguide Side Coupled with Optical Cavities

A model of a multi-band-stop filter is proposed for single-photon transport, using a one-dimensional waveguide side coupled with a series of optical cavities. Its transmission behavior is theoretically studied by a real-space model Hamiltonian and is found to depend on cavity mode frequencies, cavity relative phases, as well as cavity number and the coupling strength between the waveguide and the optical cavities. With proper cavity-mode frequencies and relative phases, the proposed model shows multi-band-stop regions and a rectangular transmission spectrum. Based on these phenomena, optical filters with more than one band-stop regions are simulated with gold material in the THz and communication band.     

Critical comparison of the experimental optical activity of helical polypeptides and the predictions of the molecular exciton model

The predictions of the presently accepted molecular exciton model for the optical activity of helical polypeptides are in reasonable agreement with experimental spectra in the accessible wavelength range. However, crucial verification requires the detect of a significant negative rotatory hand just below the accessible range. A computer-oriented method is utilized to obtain information concerning the inaccessible range. Optical rotatory dispersion computed by evaluation of the Kronig-Kramers integral transform from the experimentally determined circular dichroism of several helical homopolypeptides in solution are compared with the experimentally determined optical rotatory dispersion. Computed and experimental curves are congruent within an uncertainty approaching that of the experimental technique, whatever the polypeptide sample lot, side chains, and solvent. It is shown that t his agreement is not a computational or experimental artifact. These results can be interpreted in two ways: (1) that the predicted band does not exist, and (2) that the perturbation of the predicted band is being negated by other inaccessible bands in the vacuum ultraviolet. Arguments are presented to show that the first of these two possibilities is more probable.     

Design of Plasmonic Comb-Like Filters Using Loop-Based Resonators

A subwavelength plasmonic comb-like filter is proposed by using dual symmetric slot cavities which are placed between two parallel metal–insulator–metal (MIM) structure waveguides. The structure can be considered as a resonance loop which consists of slot cavity resonators and MIM waveguide resonators. The reflective wavelength range and channel spacing are determined by the lengths of slot cavities and MIM waveguides, respectively. Three, four, and five reflective channels with high reflection are achieved in a small wavelength range. Higher channel count can be available by increasing the length or the real part of effective index of MIM waveguides. Such a device can find applications in various optical systems such as wavelength demultiplexing components.     

Assay of DNA-RNA hybrids by S1 nuclease digestion and adsorption to DEAE-cellulose filters.

A fast and accurate assay procedure for DNA-RNA hybrids is described in which exhaustive digestion of unhybridized DNA with S1 nuclease is followed by binding of hybrids to filter discs of DEAE-cellulose. The digested DNA can be efficiently washed from the filters so that background levels of 0.1-0.2% of input tracer DNA can be achieved, in contrast to the much higher (approximately 1-5%) backgrounds obtained using TCA precipitation procedures. Short duplexes, as small as 36 nucleotides in length, which are inefficiently bound to hydroxyapatite, are quantitatively bound to the DEAE-cellulose filters.     

The effect of sound intensity on duration-tuning characteristics of bat inferior collicular neurons

Previous studies have shown that inferior collicular neurons of the big brown bat, Eptesicus fuscus, serve as short-, band-, long- and all-pass filters for sound durations. Neurons with band-, short- and long-pass filtering characteristics discharged maximally to a specific sound duration or a range of sound durations. In contrast, neurons with all-pass filtering characteristics do not have duration selectivity. To determine if duration-tuning characteristics of collicular neurons were tolerant to changes in sound intensity, we examined the duration-tuning characteristics of collicular neurons using a wide range of sound intensities. Duration-tuning characteristics examined included the type, bandwidth and slope of duration-tuning curves. Sound intensity delivered within 20 dB of minimum threshold did not affect duration-tuning characteristics of all collicular neurons studied. Sound intensities at still higher levels did not affect the tuning characteristics of two-thirds of collicular neurons but decreased the duration selectivity and changed the duration-tuning curves of the remaining one-third of neurons from one type to another. However, these two groups of duration-tuning collicular neurons were not separately organized inside the inferior colliculus. The biological relevance of these findings to bat echolocation is discussed.     

A Plasmonic Wavelength-Selected Intersection Structure

A subwavelength intersection structure with wavelength filtering functionality is proposed by using an open loop which consists of four slot cavities and four metal-insulator-metal (MIM) drop waveguides. The slot cavities are used as the resonators while the MIM waveguides serve as the input/output ports. The SPPs propagations and the transmission wavelengths in two pairs of matched input/output ports are immune to each other, which satisfy the intersection characters. The results based on finite difference time domain (FDTD) method demonstrate that high transmittance for the expected output port and high isolation for other ports have been achieved. Specifically, the transmittance and isolation is larger than 0.64 and 14 dB, respectively. In addition, a transmission peak, whose wavelength can be modulated by adjusting the length of the slot cavities, is available for the output port. Such a device can find applications in various optical systems, such as the wavelength filtering area and the optical intersection area.     

光刺激参数控制器

本文介绍一种能准确而迅速改变光刺激器光学参数(波长、强度等)的远距控制装置。将具有不同光学参数的滤光片(或孔径)置于转盘的不同位置,并对其编码。通过对编码值与预置值的比较,驱动步进马达带动转盘到所需的位置。仪器操作简便,有良好的重复性。     

Inactivation of enterococci and fecal coliforms from sewage and meatworks effluents in seawater chambers.

Inactivation in sunlight of fecal coliforms (FC) and enterococci (Ent) from sewage and meatworks effluents was measured in 300-liter effluent-seawater mixtures (2% vol/vol) held in open-topped chambers. Dark inactivation rates (kDs) were measured (from log-linear survival curves) in enclosed chambers and 6-liter pots. The kD for FC was 2 to 4 times that for Ent, and inactivation was generally slower at lower temperatures. Sunlight inactivation was described in terms of shoulder size (n) and the slope (k) of the log-linear portion of the survival curve as a function of global solar insolation and UV-B fluence. The n values tended to be larger for Ent than for FC, and the k values for FC were around twice those for Ent in both effluent-seawater mixtures. The combined sunlight data showed a general inactivation rate (k) ranking in effluent-seawater mixtures of meatworks FC > sewage FC > meatworks Ent > sewage Ent. Describing 90% inactivation in terms of insolation (S90) gave far less seasonal variation than T90 (time-dependent) values. However, there were significant differences in inactivation rates between experiments, indicating the contribution to inactivation of factors other than insolation. Inactivation rates under different long-pass optical filters decreased with the increase in the spectral cutoff wavelength (lambda 50) of the filters and indicated little contribution by UV-B to total inactivation. Most inactivation appeared to be caused by two main regions of the solar spectrum--between 318 and 340 nm in the UV region and > 400 nm in the visible region.     

Proliferation of smooth muscle cells in the inner and outer layers of the tunica media of arteries: an in vitro study

During the development of atherosclerotic and fibromuscular proliferates/lesions, smooth muscle cells (SMC) in the media, particularly near the lumen, are activated to migrate into the intima, where they continue to proliferate to form an intimal thickening. It is to date unclear whether SMCs situated adjacent to the adventitia possess a lower capacity to proliferate because they are a special subpopulation of medial SMCs or because the adventitia excerts an inhibitory effect. We have, therefore, developed an in vitro system whereby we have attempted to clear up this uncertainty. The following observations were made from the in vitro experiments: Media-explants from rabbit aorta were laid on a polycarbonate filter with pores 5 microns in diameter. The SMCs migrated through the pores and formed a fibromuscular proliferate on the other side of the filter. Endothelial cells were seeded on one side of the filter before media-explants were laid on the other side of the filter. The confluent endothelium inhibited migration of SMCs through the filter pores. Media-explants were placed between two polycarbonate filters (pores 5 microns diameter). In this "sandwich" arrangement SMCs migrated through both filters, i.e., in both directions. The quantity of migrating and proliferating cells through both filters was almost identical. This suggests that there is no difference in the migratory and proliferative capacity of SMCs in the inner and outer layers in the media of arteries. To investigate the influence of the adventitia on medial SMCs, media-explants were placed between a lower (5 microns) and an upper (0.2 micron) filter. On the 0.2 micron filter adventitia-explants were laid above the media-explants. The 0.2 micron filter prevented migration of SMCs from the media-explant into the adventitia and migration of fibroblasts from the adventitia into the media. Interestingly, the adventitial tissue inhibited proliferation of SMCs at the abluminal and migration and proliferation at the luminal side of the media-explant; the number of cells migrating through the 5 microns pores at the luminal side was diminished, suggesting that the adventitial tissue has an antiproliferative influence on SMCs. Moreover, it was found that in media-explants near the filter with adventitia, the medial SMCs were in a better preserved condition than at the de-endothelialised luminal side. As a control, cultures consisting of media-explants were incubated without filters (i.e., explant organ cultures). The proliferates in the concavity (luminal side) exhibited a pattern of proliferating SMCs different from that of the cells at the abluminal convexity.(ABSTRACT TRUNCATED AT 400 WORDS)     

Effects of humic materials on virus recovery from water.

Humic and fulvic acids were tested for their ability to interfere with virus recovery by microporous filters. Two electropositively charged types of filter (Seitz S and Zeta Plus 60S) were used to concentrate poliovirus in the presence of humic materials. Humic acid inhibited virus adsorption, but even at the highest humic acid concentrations tested (200 mg/liter), 30 to 40% of the virus was recovered by the filters. Fulvic acid, tested with Zeta Plus filters, did not affect virus recovery. For comparison, two electronegatively charged filter types were tested (Cox and Balston). These two types of filter were more sensitive to interference at lower concentrations of humic acid than the more positively charged filters. With Balston filters, at humic acid concentrations above 10 mg/liter, most of the virus was recovered in the filtrate. Fulvic acid, tested with Balston filters, did not interfere with virus recovery. With the electropositively charged filters, the humic materials adsorbed efficiently, even at high input concentrations. Interference with virus adsorption occurred at humic acid concentrations which were below the level of saturation of the filters. In addition, in high-volume experiments, humic acid led to premature blockage of the filters. The efficiency of virus recovery by a second concentration step, organic flocculation of the filter eluate, was tested. For all the filter types tested, this procedure was not affected by the presence of humic or fulvic acid in the input water.