A new method to normalize plantar pressure measurements for foot size and foot progression angle

Plantar pressure measurement provides important information about the structure and function of the foot and is a helpful tool to evaluate patients with foot complaints. In general, average and maximum plantar pressure of 6–11 areas under the foot are used to compare groups of subjects. However, masking the foot means a loss of important information about the plantar pressure distribution pattern. Therefore, the purpose of this study was to develop and test a simple method that normalizes the plantar pressure pattern for foot size, foot progression angle, and total plantar pressure. Moreover, scaling the plantar pressure to a standard foot opens the door for more sophisticated analysis techniques such as pattern recognition and machine learning.Twelve subjects walked at preferred and half of the preferred walking speed over a pressure plate. To test the method, subjects walked in a straight line and in an approaching angle of approximately 40°. To calculate the normalized foot, the plantar pressure pattern was rotated over the foot progression angle and normalized for foot size.After normalization, the mean shortest distance between the contour lines of straight walking and walking at an angle had a mean of 0.22 cm (SD: 0.06 cm) for the forefoot and 0.14 cm (SD: 0.06 cm) for the heel. In addition, the contour lines of normalized feet for the various subjects were almost identical.The proposed method appeared to be successful in aligning plantar pressure of various feet without losing information.     

Greater toe grip and gentler heel strike are the strategies to adapt to slippery surface

This study investigated the plantar pressure distribution during gait on wooden surface with different slipperiness in the presence of contaminants. Fifteen Chinese males performed 10 walking trials on a 5-m wooden walkway wearing cloth shoe in four contaminated conditions (dry, sand, water, oil). A pressure insole system was employed to record the plantar pressure data at 50Hz. Peak pressure and time-normalized pressure-time integral were evaluated in nine regions. In comparing walking on slippery to non-slippery surfaces, results showed a 30% increase of peak pressure beneath the hallux (from 195.6 to 254.1kPa), with a dramatic 79% increase in the pressure time integral beneath the hallux (from 63.8 to 114.3kPa) and a 34% increase beneath the lateral toes (from 35.1 to 47.2kPa). In addition, the peak pressure beneath the medial and lateral heel showed significant 20-24% reductions, respectively (from 233.6-253.5 to 204.0-219.0kPa). These findings suggested that greater toe grip and gentler heel strike are the strategies to adapt to slippery surface. Such strategies plantarflexed the ankle and the metatarsals to achieve a flat foot contact with the ground, especially at heel strike, in order to shift the ground reaction force to a more vertical direction. As the vertical ground reaction force component increased, the available ground friction increased and the floor became less slippery. Therefore, human could walk without slip on slippery surfaces with greater toe grip and gentler heel strike as adaptation strategies.     

Plantar ROI Characterization during the Stance Phase of Gait Based on a Low-cost Pressure Acquisition Platform

Plantar Region of Interest (ROI) detection is important for the early diagnosis and treatment of morphologic defects of the foot and foot bionic research.Conventional methods have employed complex procedures and expensive instruments which prohibit their widespread use in healthcare.In this paper an automatic plantar ROIs detection method using a customized low-cost pressure acquisition device is proposed.Plantar pressure data and 3D motion capture data were collected from 28subjects (14 healthy subjects and 14 subjects with hallux valgus).The maximal inter-frame difference during the stance phase was calculated.Consequently,the ROIs were defined by the first-order difference in combination with prior anatomic knowledge.The anatomic locations were determined by the maximal inter-frame difference and second maximal inter-frame difference,which nearly coincided.Our system can achieve average recognition accuracies of 92.90％,89.30％,89.30％,92.90％,92.90％,and 89.30％ for plantar ROIs hallux and metatarsi Ⅰ-Ⅴ,respectively,as compared with the annotations using the 3Dmotion capture system.The maximal difference of metatarsus heads Ⅱ-Ⅴ,and the impulse of the medial and lateral heel features made a significant contribution to the classification of hallux valgus and healthy subjects with ≥ 80％ sensitivity and specificity.Furthermore,the plantar pressure acquisition system is portable and convenient to use,thus can be used in home- or community-based healthcare applications.     

Reduction of plantar heel pressures: Insole design using finite element analysis

Plantar heel pain is a common condition that is often exacerbated by the repetitive stresses of walking. Treatment usually includes an in-shoe intervention designed to reduce plantar pressure under the heel by using insoles and a variety of off-the-shelf products. The design process for these products is often intuitive in nature and does not always rely on scientifically derived guidelines. Finite element analysis provides an efficient computational framework to investigate the performance of a large number of designs for optimal plantar pressure reduction. In this study, we used two-dimensional plane strain finite element modeling to investigate 27 insole designs. Combinations of three insole conformity levels (flat, half conforming, full conforming), three insole thickness values (6.3, 9.5 and 12.7 mm) and three insole materials (Poron Cushioning, Microcel Puff Lite and Microcel Puff) were simulated during the early support phase of gait. Plantar pressures predicted by the model were validated by experimental trials conducted in the same subject whose heel was modeled by loading the bare foot on a rigid surface and on foam mats. Conformity of the insole was the most important design variable, whereas peak pressures were relatively insensitive to insole material selection. The model predicted a 24% relief in pressure compared to barefoot conditions when using flat insoles; the reduction increased up to 44% for full conforming insoles.     

Effect of heel height on in-shoe localized triaxial stresses

Abnormal and excessive plantar pressure and shear are potential risk factors for high-heeled related foot problems, such as forefoot pain, hallux valgus deformity and calluses. Plantar shear stresses could be of particular importance with an inclined supporting surface of high-heeled shoe. This study aimed to investigate the contact pressures and shear stresses simultaneously between plantar foot and high-heeled shoe over five major weightbearing regions: hallux, heel, first, second and fourth metatarsal heads, using in-shoe triaxial force transducers. During both standing and walking, peak pressure and shear stress shifted from the lateral to the medial forefoot as the heel height increased from 30 to 70mm. Heel height elevation had a greater influence on peak shear than peak pressure. The increase in peak shear was up to 119% during walking, which was about five times that of peak pressure. With increasing heel height, peak posterolateral shear over the hallux at midstance increased, whereas peak pressure at push-off decreased. The increased posterolateral shear could be a contributing factor to hallux deformity. It was found that there were differences in the location and time of occurrence between in-shoe peak pressure and peak shear. In addition, there were significant differences in time of occurrence for the double-peak loading pattern between the resultant horizontal ground reaction force peaks and in-shoe localized peak shears. The abnormal and drastic increase of in-shoe shear stresses might be a critical risk factor for shoe-related foot disorders. In-shoe triaxial stresses should therefore be considered to help in designing proper footwear.     

Parametric study of orthopedic insole of valgus foot on partial foot amputation

Orthopedic insole was important for partial foot amputation (PFA) to achieve foot balance and avoid foot deformity. The inapposite insole orthosis was thought to be one of the risk factors of reamputation for foot valgus patient, but biomechanical effects of internal tissues on valgus foot had not been clearly addressed. In this study, plantar pressure on heel and metatarsal regions of PFA was measured using F-Scan. The three-dimensional finite element (FE) model of partial foot evaluated different medial wedge angles (MWAs) (0.0°–10.0°) of orthopedic insole on valgus foot. The effect of orthopedic insole on the internal bone stress, the medial ligament tension of ankle, plantar fascia tension, and plantar pressure was investigated. Plantar pressure on medial heel region was about 2.5 times higher than that of lateral region based on the F-Scan measurements. FE-predicted results showed that the tension of medial ankle ligaments was the lowest, and the plantar pressure was redistributed around the heel, the first metatarsal, and the lateral longitudinal arch regions when MWA of orthopedic insole ranged from 7.5° to 8.0°. The plantar fascias maintained about 3.5% of the total load bearing on foot. However, the internal stresses from foot bones increased. The simulation in this study would provide the suggestion of guiding optimal design of orthopedic insole and therapeutic planning to pedorthist.     

Dynamic plantar loading index: understanding the benefit of custom foot orthoses for painful pes cavus

The purpose of this study was to evaluate a new method showing how custom foot orthoses (CFO) improve dynamics of plantar loading. The method is based on the probability distribution of peak pressure time series and is quantified using the Regression Factor (RF). RF is a least square regression slope between the experimentally observed plantar pressure magnitude probability distribution and a modeled Gaussian shape. Plantar pressure data from a randomized controlled trial of 154 participants with painful Pes Cavus were retrospectively re-analyzed. The participants were randomized to an active treatment group given CFO or a control group given sham orthoses. The location of 2(nd) Peak pressure as a percentage of stance time (P(Loc2)) and its magnitude (P(M2)) was also calculated. In addition, plantar pressure data were collected on 23 healthy volunteers with normal foot alignment and no foot pain. Results demonstrated Pes Cavus had a significantly lower RF than healthy participants (0.30 v. 0.51; p<10(-7)). P(M2) was reduced in both active and control groups. However, RF and the P(Loc2) were only changed in the active group (p<0.005) without any significant change in the control group (p>0.5). This study suggests that painful Pes Cavus alters the shape of probability distribution of plantar loading during walking and CFO are an effective therapeutic solution that can significantly improve it. Further use of the RF index and 2(nd) peak pressure location as an outcome measure for treatment of foot and ankle deformities is suggested.     

Predictors of Barefoot Plantar Pressure during Walking in Patients with Diabetes,Peripheral Neuropathy and a History of Ulceration

ObjectiveElevated dynamic plantar foot pressures significantly increase the risk of foot ulceration in diabetes mellitus. The aim was to determine which factors predict plantar pressures in a population of diabetic patients who are at high-risk of foot ulceration.MethodsPatients with diabetes, peripheral neuropathy and a history of ulceration were eligible for inclusion in this cross sectional study. Demographic data, foot structure and function, and disease-related factors were recorded and used as potential predictor variables in the analyses. Barefoot peak pressures during walking were calculated for the heel, midfoot, forefoot, lesser toes, and hallux regions. Potential predictors were investigated using multivariate linear regression analyses. 167 participants with mean age of 63 years contributed 329 feet to the analyses.ResultsThe regression models were able to predict between 6% (heel) and 41% (midfoot) of the variation in peak plantar pressures. The largest contributing factor in the heel model was glycosylated haemoglobin concentration, in the midfoot Charcot deformity, in the forefoot prominent metatarsal heads, in the lesser toes hammer toe deformity and in the hallux previous ulceration. Variables with local effects (e.g. foot deformity) were stronger predictors of plantar pressure than global features (e.g. body mass, age, gender, or diabetes duration).ConclusionThe presence of local deformity was the largest contributing factor to barefoot dynamic plantar pressure in high-risk diabetic patients and should therefore be adequately managed to reduce plantar pressure and ulcer risk. However, a significant amount of variance is unexplained by the models, which advocates the quantitative measurement of plantar pressures in the clinical risk assessment of the patient.     

Structural and functional predictors of regional peak pressures under the foot during walking

The objective of this study was to identify structural and functional factors which are predictors of peak pressure underneath the human foot during walking. Peak plantar pressure during walking and eight data sets of structural and functional measures were collected on 55 asymptomatic subjects between 20 and 70 yr. A best subset regression approach was used to establish models which predicted peak regional pressure under the foot. Potential predictor variables were chosen from physical characteristics, anthropometric data, passive range of motion (PROM), measurements from standardized weight bearing foot radiographs, mechanical properties of the plantar soft tissue, stride parameters, foot motion in 3D, and EMG during walking. Peak pressure values under the rearfoot, midfoot, MTH1, and hallux were measured. Heel pressure was a function of linear kinematics, longitudinal arch structure, thickness of plantar soft tissue, and age. Midfoot pressure prediction was dominated by arch structure, while MTH1 pressure was a function of radiographic measurements, talo-crural joint motion, and gastrocnemius activity. Hallux pressure was a function of structural measures and MTP1 joint motion. Foot structure and function predicted only approximately 50% of the variance in peak pressure, although the relative contributions in different anatomical regions varied dramatically. Structure was dominant in predicting peak pressure under the midfoot and MTH1, while both structure and function were important at the heel and hallux. The predictive models developed in this study give insight into potential etiological factors associated with elevated plantar pressure. They also provide direction for future studies designed to reduce elevated pressure in "at-risk" patients.     

Spatial resolution in plantar pressure measurement revisited

Plantar pressures are typically measured using sensors of finite area, so the accuracy with which one can measure true maximum pressure is dependent on sensor size. Measurement accuracy has been modeled previously for one patient's metatarsals (Lord, 1997), but has not been modeled either for general subjects or for other parts of the foot. The purposes of this study were (i) to determine whether Lord's (1997) model is also valid for heel and hallux pressures, and (ii) to examine how sensor size relates to measurement accuracy in the context of four factors common to many measurement settings: pressure pulse size, foot positioning, pressure change quantification, and gross pressure redistribution. Lord's (1997) model was first generalized and was then validated using 10 healthy walking subjects, with relatively low RMSE values on the order of 20 kPa. Next, postural data were used to show that gross pressure redistributions can be accurately quantified (p<0.002), even with rather gross sensor sizes of 30 mm. Finally, numerical analyses revealed that the relation between sensor size and measurement accuracy is highly complex, with deep dependency on the measurement context. In particular, the critical sensor widths required to achieve 90% accuracy ranged from 1.7 mm to 17.4 mm amongst the presently investigated scenarios. Since measurement accuracy varies so extensively with so many factors, the current results cannot yield specific recommendations regarding spatial resolution. It is concluded simply that no particular spatial resolution can yield a constant measurement accuracy across common plantar pressure measurement tasks.     

Predicting changes in knee adduction moment due to load-altering interventions from pressure distribution at the foot in healthy subjects

The purpose of this pilot study of healthy subjects was to determine if changes in foot pressure patterns associated with a lateral wedge can predict the changes in the knee adduction moment. We tested two hypotheses: (1) increases or decreases in the knee adduction moment and ankle eversion moment due to load-altering footwear interventions can be predicted from foot pressure distribution and (2) changes in magnitude of the knee adduction moment and ankle eversion moment due to lateral wedges can be predicted from pressure distribution at the foot during walking. Fifteen healthy adults performed walking trials in three shoes: 0 degrees , 4 degrees , and 8 degrees laterally wedged. Maximum heel pressure ratio, first peak knee adduction moment, and peak ankle eversion moment were assessed using a pressure mat, motion capture system, and force plate. Increases or decreases in the knee adduction moment and ankle eversion moment were predicted well from foot pressure distribution. However, the magnitude of the pressure change did not predict the magnitude of the peak knee adduction moment change or peak ankle eversion moment change. Factors such as limb alignment or trunk motion may affect the knee adduction moment and override a direct relationship between the pressure distribution at the shoe-ground interface and the load distribution at the knee. However, changes (increases or decreases) in the peak knee adduction moment due to load-altering footwear interventions predicted from pressure distribution during walking can be important when evaluating these types of interventions from a clinical perspective.     

Natural gaits of the non-pathological flat foot and high-arched foot

There has been a controversy as to whether or not the non-pathological flat foot and high-arched foot have an effect on human walking activities. The 3D foot scanning system was employed to obtain static footprints from subjects adopting a half-weight-bearing stance. Based upon their footprints, the subjects were divided into two groups: the flat-footed and the high-arched. The plantar pressure measurement system was used to measure and record the subjects' successive natural gaits. Two indices were proposed: distribution of vertical ground reaction force (VGRF) of plantar and the rate of change of footprint areas. Using these two indices to compare the natural gaits of the two subject groups, we found that (1) in stance phase, there is a significant difference (p<0.01) in the distributions of VGRF of plantar; (2) in a stride cycle, there is also a significant difference (p<0.01) in the rate of change of footprint area. Our analysis suggests that when walking, the VGRF of the plantar brings greater muscle tension to the flat-footed while a smaller rate of change of footprint area brings greater stability to the high-arched.     

An MRI-compatible foot-loading device for assessment of internal tissue deformation

It is well known that mechanical forces acting within the soft tissues of the foot can contribute to the formation of neuropathic ulcers in people with diabetes. Presently, only surface measurements of plantar pressure are used clinically to estimate risk status due to mechanical loading. It is currently not known how surface measurements relate to the three-dimensional (3-D) internal stress/strain state of the foot. This article describes the development of a foot-loading device that allows for the direct observation of the internal deformation of foot tissues under known forces. Ground reaction forces and plantar pressure distributions during normal walking were measured in ten healthy young adults. One instant in the gait cycle, when pressure under the metatarsal heads reached a peak, was extracted for simulation in an MR imager. T1-weighted 3-D gradient echo MRI sets were collected as the simulated walking ground reaction force was incrementally applied to the foot by the novel foot-loading device. The sub-metatarsal head soft-tissue thickness decreased rapidly at first and then reached a plateau. Peak plantar pressure measurements collected within the loading device (161+/-75kPa) were lower in magnitude and less focal than pressures measured during walking (492+/-91kPa). This finding implies that although the device successfully applied full peak walking ground reaction forces to the foot, they were not distributed in the same manner as during walking. Although not representative of gait, the data collected from this in vivo mechanical test are suitable for determination of foot tissue material properties or, when combined with finite element modeling, to examine the relationship between surface loading and internal stress.     

Differences in foot contact times between obese and non-obese postmenopausal women when crossing obstacles

Abstract

Objective: This study aimed to investigate the foot contact time differences between obese and non-obese subjects during walking when crossing obstacles.

Methods: Ninety-eight postmenopausal women were assigned to four groups, and their plantar pressure temporal data were collected using a two-step protocol during walking when crossing an obstacle set at 30% height of lower limb length of each subject. The initial, final, and duration of contact of 10?foot areas were measured.

Results: Leading limb: (1) the heel groups initiated foot contact using the heel, and the non-heel groups initiated contact using the metatarsals; (2) heel obese subjects showed an earlier initial contact and a longer contact duration of metatarsals 2–3; (3) non-heel obese subjects showed an earlier midfoot initial contact. Regarding the trailing limb: (4) heel obese subjects showed an earlier midfoot initial contact and a longer contact duration of metatarsal 5; (5) non-heel obese subjects showed an earlier initial contact and a longer contact duration of metatarsals 4–5.

Conclusions: (1) The non-heel groups’ foot rollover pattern may result from an attempt of rapidly restoring stability; (2) the heel obese subjects seem to regulate their plantar foot muscles to overcome their overweight; (3) the overweight of the non-heel obese subjects leads to a quicker backward foot roll-over from the metatarsals to the heel; (4) the overweight of the heel obese subjects can distort their footprints and/or their higher inertia may precipitate an anticipation of the midfoot contact, which can also explain the result observed for 5.     

Deformation and stress distribution of the human foot after plantar ligaments release: A cadaveric study and finite element analysis

The majority of foot deformities are related to arch collapse or instability, especially the longitudinal arch. Although the relationship between the plantar fascia and arch height has been previously investigated, the stress distribution remains unclear. The aim of this study was to explore the role of the plantar ligaments in foot arch biomechanics. We constructed a geometrical detailed three-dimensional (3-D) finite element (FE) model of the human foot and ankle from computer tomography images. The model comprised the majority of joints in the foot as well as bone segments, major ligaments, and plantar soft tissue. Release of the plantar fascia and other ligaments was simulated to evaluate the corresponding biomechanical effects on load distribution of the bony and ligamentous structures. These intrinsic ligaments of the foot arch were sectioned to simulate different pathologic situations of injury to the plantar ligaments, and to explore bone segment displacement and stress distribution. The validity of the 3-D FE model was verified by comparing results with experimentally measured data via the displacement and von Mise stress of each bone segment. Plantar fascia release decreased arch height, but did not cause total collapse of the foot arch. The longitudinal foot arch was lost when all the four major plantar ligaments were sectioned simultaneously. Plantar fascia release was compromised by increased strain applied to the plantar ligaments and intensified stress in the midfoot and metatarsal bones. Load redistribution among the centralized metatarsal bones and focal stress relief at the calcaneal insertion were predicted. The 3-D FE model indicated that plantar fascia release may provide relief of focal stress and associated heel pain. However, these operative procedures may pose a risk to arch stability and clinically may produce dorsolateral midfoot pain. The initial strategy for treating plantar fasciitis should be non-operative.     

Dynamic plantar pressure distribution during terrestrial locomotion of bonobos (Pan paniscus)

We collected high-resolution plantar pressure distributions of seven bonobos during terrestrial bipedal and quadrupedal locomotion (N = 146). Functional foot length, degree of hallux abduction, and total contact time were determined, and plots, showing pressure as a function of time for six different foot regions, were generated. We also studied five adult humans for comparison (N = 13). Both locomotion types of the bonobo show a large variation in plantar pressure distributions, which could be due to the interference of instantaneous behavior with locomotion and differences in walking speed and body dimensions. The heel and the lateral midfoot typically touch down simultaneously at initial ground contact in bipedal and quadrupedal walking of bonobos, in contrast with the typical heel-strike of human bipedalism. The center of pressure follows a curved course during quadrupedalism, as a consequence of the medial weight transfer during mid-stance. Bipedal locomotion of bonobos is characterized by a more plantar positioning of the feet and by a shorter contact time than during quadrupedal walking, according to a smaller stride and step length at a higher frequency. We observed a varus position of the foot with an abducted hallux, which likely possesses an important sustaining and stabilizing function during terrestrial locomotion.     

Image-based midsole insert design and the material effects on heel plantar pressure distribution during simulated walking loads

The primary objective of this paper is to study the use of medical image-based finite element (FE) modelling in subject-specific midsole design and optimisation for heel pressure reduction using a midsole plug under the calcaneus area (UCA). Plugs with different relative dimensions to the size of the calcaneus of the subject have been incorporated in the heel region of the midsole. The FE foot model was validated by comparing the numerically predicted plantar pressure with biomechanical tests conducted on the same subject. For each UCA midsole plug design, the effect of material properties and plug thicknesses on the plantar pressure distribution and peak pressure level during the heel strike phase of normal walking was systematically studied. The results showed that the UCA midsole insert could effectively modify the pressure distribution, and its effect is directly associated with the ratio of the plug dimension to the size of the calcaneus bone of the subject. A medium hardness plug with a size of 95% of the calcaneus has achieved the best performance for relieving the peak pressure in comparison with the pressure level for a solid midsole without a plug, whereas a smaller plug with a size of 65% of the calcaneus insert with a very soft material showed minimum beneficial effect for the pressure relief.     

Image-based midsole insert design and the material effects on heel plantar pressure distribution during simulated walking loads

The primary objective of this paper is to study the use of medical image-based finite element (FE) modelling in subject-specific midsole design and optimisation for heel pressure reduction using a midsole plug under the calcaneus area (UCA). Plugs with different relative dimensions to the size of the calcaneus of the subject have been incorporated in the heel region of the midsole. The FE foot model was validated by comparing the numerically predicted plantar pressure with biomechanical tests conducted on the same subject. For each UCA midsole plug design, the effect of material properties and plug thicknesses on the plantar pressure distribution and peak pressure level during the heel strike phase of normal walking was systematically studied. The results showed that the UCA midsole insert could effectively modify the pressure distribution, and its effect is directly associated with the ratio of the plug dimension to the size of the calcaneus bone of the subject. A medium hardness plug with a size of 95% of the calcaneus has achieved the best performance for relieving the peak pressure in comparison with the pressure level for a solid midsole without a plug, whereas a smaller plug with a size of 65% of the calcaneus insert with a very soft material showed minimum beneficial effect for the pressure relief.     

Influence of the posterior tibial tendon on the medial arch of the foot: an in vitro kinetic and kinematic study]

INTRODUCTION: The respective contributions of the active and passive structures of the foot to the stability of the medical arch were investigated using an in vitro kinetic and kinematic model. The effect of the tibialis posterior tendon on foot and ankle movements, and plantar pressure distribution of the foot were tested in a cadaveric human foot. METHOD: The stance phase from heel-contact to toe-off of normal walking gait and after tibialis posterior tendon rupture was simulated in eight roentenographically normal human feet (age 66 +/- 19 years, males). Ground reaction force and tibial inclination was simulated by means of a tilting angle and force-controlled translation stage. Plantar pressure was measured using a pressure-measuring platform. The force developed by the flexors and extensor muscles of the foot were simulated via cables attached to 7 force-controlled hydraulic cylinders. Tibial rotation was produced by an electric servo-motor, and foot movements measured with an ultrasonic analysis system. RESULTS: The model was verified against the plantar distribution and kinematics of healthy subjects measured during normal gait. Tibialis posterior deficit did not result in any detectable changes in pressure or force-time integral in the medial regions of the foot--a common sign of flat foot (pressure: midfoot 0.2 < or = 0.9; medial forefoot 0.5 < or = p < or = 0.9; hallux 0.5 < or = p < or = 0.9; force-time integral: midfoot p = 0-871; medial forefoot p = 0.632; hallux p = 0.068). Only small tendential changes in the kinematics of the talus and calcaneus were observed in dorsiflexion (0-58 sec; talus 0.1 < or = p < or = 0.6; calcaneus 0.4 < or = p < or = 0.06) and eversion (talus: 0-60 sec. 0.1 < or = p < or = 0.6; calcaneus: 37-60 sec. 0.2 < or = p < or = 0.7). CONCLUSION: The results of this in vitro study show that defective tibialis posterior alone does not produce significant changes in the kinetics or kinematics of the stance phase of normal gait. This suggests that the development of flat foot observed in degeneration of the tibialis posterior tendon occurs only after fatigue of the passive structures of the foot.     

Temporal characteristics of plantar shear distribution: relevance to diabetic patients

Diabetic foot ulcers are known to have a biomechanical etiology. Among the mechanical factors that cause foot lesions, shear stresses have been either neglected or underestimated. The purpose of this study was to determine various plantar pressure and shear variables in the diabetic and control groups and compare them. Fifteen diabetic patients with neuropathy and 20 non-diabetic subjects without foot symptoms were recruited. Subjects walked on a custom-built platform capable of measuring local normal and tangential forces simultaneously. Pressure-time integral quantities were increased by 54% (p=0.013) in the diabetic group. Peak AP and resultant shear magnitudes were found to be about 32% larger (p<0.05), even though diabetic subjects walked at a slower velocity. Lower AP and ML stress range (peak-to-peak) values were observed in the control subjects (p<0.05). Shear-time integral values were increased in the diabetic group by 61% and 132% for AP and resultant shear cases, respectively (p<0.05). Plantar shear is known to be a factor in callus formation and has previously been associated with higher ulcer incidence. During gait, shear stresses are induced with twice the frequency of pressure characteristically. Therefore, plantar shear should be investigated further from a broader perspective including the temporal specifications and fatigue failure characteristics of the affected plantar tissue.