Immobilization of nucleoside diphosphatase at its allosteric site using immobilized derivatives of pyridoxal 5'-phosphate

3-O-Immobilized and 6-immobilized pyridoxal 5′-phosphate analogs of Sepharose were bound to the allosteric site of nucleoside diphosphatase with very high affinity. Active immobilized nucleoside diphosphatase was prepared by reduction of the Schiff base linkage between the enzyme and pyridoxal 5′-phosphate bound to Sepharose with NaBH₄. 3-O-Immobilized pyridoxal 5′-phosphate analog gave more active immobilized enzyme than the 6-analog; the immobilized enzyme on the 3-O-immobilized pyridoxal 5′-phosphate analog showed about 90% of activity of free enzyme. The immobilized enzyme thus prepared was less sensitive to ATP, an allosteric effector, and showed a higher heat stability than the free enzyme. When an assay mixture containing inosine diphosphate and MgCl₂ was passed through a column of the immobilized enzyme at 37 °C, inosine diphosphate liberated inorganic phosphate almost quantitatively. Properties of the immobilized enzyme on the pyridoxal 5′-phosphate analog were compared with those of the immobilized enzyme on CNBr-activated Sepharose.     

Cyclodextrin production by Bacillus firmus strain 37 immobilized on inorganic matrices and alginate gel

Production of β-cyclodextrin (β-CD) by Bacillus firmus strain 37 cells, immobilized by adsorption on silica–titania (SiO₂/TiO₂) and silica–manganese dioxide (SiO₂/MnO₂) matrices, was optimized for temperature, substrate concentration and initial biomass. The immobilization process was most efficient at 60 °C with 10% maltodextrin and 1.0 g of cells, resulting, after a 5-day assay, in a β-CD production of 11.7 ± 0.1 mM for cells immobilized on SiO₂/TiO₂ and 11.2 ± 0.1 mM in SiO₂/MnO₂. Entrapment in alginate gel resulted in a maximum β-CD production of 4.1 ± 0.1 mM, which was maintained constantly until the end of a 10-day assay. During this same period, free cells produced 8.3 ± 0.2 mM, and cells immobilized on SiO₂/TiO₂ and SiO₂/MnO₂, 16.7 ± 0.4 and 17.3 ± 0.5 mM, respectively. β-CD production by cells immobilized in calcium alginate in four repetitive cycles of 5 days each, showed an increase up to the third cycle, reaching 4.8 ± 0.2 mM, while production by free cells started falling from the second cycle. In this same assay, cells immobilized on SiO₂/TiO₂ and SiO₂/MnO₂, showed the best β-CD production results at the end of the first cycle, with a gradual fall occurring due to the desorption of cells thereafter.     

Chainia Penicillin V Acylase: Strain Characteristics, Enzyme Immobilization, and Kinetic Studies

Aerobic cultures of an actinomycete were found to produce penicillin V acylase (PVA) (PA, EC-3.5.1.11) extracellularly. The presence of L-2-3 diamino-propionic acid in cell wall and formation of sclerotia on culture media led to its identification as Chainia, a sclerotial Streptomyces. Partially purified acylase was adsorbed on kieselguhr and entrapped in polyacrylamide gel. The immobilized preparation proved effective with respect to retention of enzyme and enzyme activity even after 15 successful cycles. The pH optimum for crude enzyme was in the range of pH 7.5–8.0, and for the (NH4)₂ SO₄ fraction it was pH 8.5. The immobilized enzyme showed maximal activity at pH 9.5. The optimum temperature for acylase activity was at 55°C. The crude enzyme, ammonium sulfate fraction, and immobilized enzyme showed K _m value for penicillin V of 6.13 mM, 14.3 mM, and 17.1 mM, respectively. Received: 11 December 1997 / Accepted: 9 April 1998     

Enzymatic splitting of penicillin V for the production of 6-APA using immobilized penicillin V acylase

Penicillin V acylase from Fusarium sp. SKF 235 was immobilized on several cation-exchange resins, of which Amberlite CG-50 was preferred. Maximum activity of the immobilized penicillin V acylase was 250 to 280 IU/g dry beads. The pH and temperature optima of the enzyme shifted from 6.5 to 6.8 and 55°C to 60°C, respectively, as a result of immobilization. However, the K _m for penicillin V remained at 10mm. Parameters for producing 6-aminopenicillanic acid were investigated and the immobilized penicillin V acylase was used for 68 cycles in a stirred tank reactor.     

Stabilization of d-amino acid oxidase from Rhodosporidium toruloides by immobilization onto magnetic nanoparticles

d-Amino acid oxidase from Rhodosporidium toruloides was immobilized onto glutaraldehyde-activated magnetic nanoparticles. Approximately four enzyme molecules were attached to one magnetic nanoparticle when the weight ratio of the enzyme to the support was 0.12. After immobilization, the T _m was increased from 45°C of the free form to 55°C. In the presence of 20 mM H₂O₂, the immobilized form retained 93% of its activity after 5 h while the free form was completely inactivated after 3.5 h.     

Development of a benzene vapour sensor utilizing chemiluminescence on Y2O3

Chemiluminescence (CL) was observed when benzene vapour passed through the surface of Y₂O₃, TiO₂, Y₂O₃–V₂O₅, TiO₂–Y₂O₃, Y₂O₃–Cr₂O₃, Y₂O₃–Al₂O₃ and TiO₂–Al₂O₃, with air as the carrier gas. The strongest CL intensity was found with Y₂O₃ as the catalyst. A novel benzene sensor based on this kind of CL was developed. Quantitative analysis was performed at the wavelength of 425 nm. Under optimal conditions, CL intensity was directly proportional to the concentration of benzene vapour. The linear range was 4–7018 mg/m³ (r = 0.9981, n = 11), with a detection limit of 1 mg/m³ (the signal:noise ratio was 3). This gas sensor can work continuously for >80 h and has been successfully applied to the real‐time determination of benzene vapour. Copyright © 2008 John Wiley & Sons, Ltd.     

Bioaffinity Based Oriented Immobilization of Stem Bromelain

Bromelain is a basic, 23.8 kDa thiol proteinase obtained from stem of the pineapple plant (Ananas comosus) and is unique in containing a single oligosaccharide chain attached to the polypeptide. This property allowed its affinity binding and favorable orientation on a Sepharose support pre-coupled with the lectin, concanavalin A (Con A). For comparison, bromelain was also immobilized by covalently coupling to the CNBr-activated Sepharose. The preparation obtained was more resistant to thermal inactivation as evident from the retention of over 50% activity after incubation at 60 for 100 min (as compared to 20% retained by the native enzyme and 30% retained by the covalently immobilized enzyme), exhibited a broader pH-activity profile with the enzyme retaining over 60% activity at pH 11 (as compared to over 25% retained by native and the enzyme immobilized covalently). The native, covalently-coupled and affinity-bound bromelains had apparent K _m values of 1.1, 2 and 0.54 mg/ml, respectively using casein as the substrate. The V _max values remained unaffected on immobilization.     

Analysis of the mechanism of intensification of fermentation process using yeast cells in a suspension of high-dispersed oxides

The differential microcalorimetry was used to explore an influence of particles of silicon dioxide, and also other high-dispersed oxides (0.05% of masses.) in water suspension of yeast cells on intensification of the process of their fermentation in endogenous metabolic conditions. It was shown that intensification of the processes of the vital activity of yeast microorganisms was observed in the specified interval of the concentration of silicon dioxide hydrosol particles. Mechanisms of interaction between SiO₂ particles and a surface of a cellular organism, as well as interaction between SiO₂ particles and one of metabolism products — carbon dioxide were studied. It was found out, that Al₂O₃, TiO₂ hydrosols also had a stimulating effect, but it is lower compared to that of SiO₂.     

西南峡谷型喀斯特区坡地土壤矿物质的空间分布特征

探明峡谷型喀斯特土壤矿物质的分布规律可以为喀斯特地区植被恢复和生态重建提供参考。基于动态监测样地(200 m×300 m)的网格取样,采用经典统计分析和地统计学方法分析土壤矿物质(SiO2、Fe2O3、CaO、MgO、Al2O3、MnO)的空间分布特征。结果表明,研究区土壤矿物质含量差异较大,但变异系数不大,SiO2和Al2O3占了土壤矿物质总量的85.99%;SiO2、Al2O3、MgO、MnO均服从正态分布,Fe2O3、CaO分别经过平方和倒数转换后也服从正态分布。土壤各矿物质半变异函数的最佳拟合模型均为指数模型,块金值与基台值比C0/(C0+C)均较小,具有中等或强烈的空间相关性,表明空间变异主要由结构性因素引起;Al2O3和MnO的变程较大,空间连续性较好,其它矿物质的变程较小且相近,空间依赖性较强;Kriging等值线图表明峡谷型喀斯特区土壤SiO2和MnO具有相似的空间分布,受坡位和人为干扰共同影响,基本呈现坡顶高、坡脚低的分布格局;Fe2O3、CaO和MgO的空间分布也相似,斑块较破碎,主要受地形的影响;Al2O3的空间格局呈单峰分布,沿海拔的升高而升高。因此,减少干扰、增加植被覆盖对土壤矿物质具有良好的保持和调控作用。     

Preparation and characterization of amino and carboxyl functionalized core-shell Fe3O4/SiO2 for L-asparaginase immobilization: A comparison study

Abstract

Magnetic nanoparticles are well known as facile and effective support for enzyme immobilization since they have a high surface area, large surface-to-volume ratio, easy separation, a fast and high enzyme loading. This study aims to provide insights on whether acidic or basic modified particles are more effective for L-asparaginase (ASNase) immobilization. Therefore, amino (Fe₃O₄/SiO₂/NH₂) and carboxyl-functionalized (Fe₃O₄/SiO₂/COOH) particles were prepared. The functional groups, crystalline structure, magnetic properties, morphology, chemical composition and thermal behaviour of the prepared modified nanoparticles were examined via Fourier-transform infra-red spectroscopy (FTIR), X-ray diffraction (XRD), vibrating-sample magnetometer (VSM), scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDAX). Under the optimum conditions, the immobilized enzymes were more stable within a certain range of temperatures and pH values in comparison to free enzyme. On the other hand, the immobilized enzymes showed greater stability after incubation for 3?h at 50?°C. The free enzyme maintained only 30% of its initial activity for 4?weeks at 4?°C, while Fe₃O₄/SiO₂/NH₂/ASNase and Fe₃O₄/SiO₂/COOH/ASNase retained more than 78.9% and 56.5% of initial activities under the same conditions, respectively. Moreover, Fe₃O₄/SiO₂/NH₂/ASNase (77.2%) and Fe₃O₄/SiO₂/COOH/ASNase (57.4%) displayed excellent operational stability after 17 repeated cycles. These findings suggested that the Fe₃O₄/SiO₂/NH₂ and Fe₃O₄/SiO₂/COOH may be utilized as efficient and sustainable supports to developed immobilized ASNase in several biotechnological applications.     

Photo‐Electrical Characterization of Silicon Micropillar Arrays with Radial p/n Junctions Containing Passivation and Anti‐Reflection Coatings

In order to assess the contributions of anti‐reflective and passivation effects in microstructured silicon‐based solar light harvesting devices, thin layers of aluminum oxide (Al₂O₃), silicon dioxide (SiO₂), silicon‐rich silicon nitride (SiN_x), and indium tin oxide (ITO), with a thickness ranging from 45 to 155 nm, are deposited onto regularly packed arrays of silicon micropillars with radial p/n junctions. Atomic layer deposition of Al₂O₃ yields the best conformal coating over the micropillars. The fact that layers made by low‐pressure chemical vapor deposition (SiO₂ and SiN_x) are not conformally deposited on the sidewalls of the Si micropillars do not influence the photoelectrical efficiency. For ITO, a change in composition along the micropillar height is measured, which leads to poor performance. For Al₂O₃, deconvolution of the contributions of passivation and anti‐reflection to the overall efficiency gain exhibits the importance of passivation in micro/nano‐structured Si devices. Al₂O₃‐coated samples perform the best, for both n/p and p/n configured pillars, yielding (relative) increases of 116% and 37% in efficiency of coated versus non‐coated samples for p‐type and n‐type base micropillar arrays, respectively.     

Catalytic properties of the immobilized Aspergillus tamarii xylanase

Xylanase from Aspergillus tamarii was covalently immobilized on Duolite A147 pretreated with the bifunctional agent glutaraldehyde. The bound enzyme retained 54.2% of the original specific activity exhibited by the free enzyme (120 U/mg protein). Compared to the free enzyme, the immobilized enzyme exhibited lower optimum pH, higher optimum reaction temperature, lower energy of activation, higher K_m (Michaelis constant), lower V_max (maximal reaction rate). The half-life for the free enzyme was 186.0, 93.0, and 50.0 min for 40, 50, and 60°C, respectively, whereas the immobilized form at the same temperatures had half-life of 320, 136, and 65 min. The deactivation rate constant at 60°C for the immobilized enzyme is about 6.0 × 10⁻³, which is lower than that of the free enzyme (7.77 × 10⁻³ min). The energy of thermal deactivation was 15.22 and 20.72 kcal/mol, respectively for the free and immobilized enzyme, confirming stabilization by immobilization. An external mass transfer resistance was identified with the immobilization carrier (Duolite A147). The effect of some metal ions on the activity of the free and immobilized xylanase has been investigated. The immobilized enzyme retained about 73.0% of the initial catalytic activity even after being used 8 cycles.     

Ethanol production by Zymomonas mobilis entrapped in alumina pellets

Summary Zymomonas mobilis cells were immobilized on pellets of alumina (Al₂O₃) by entrapment based on electrostatic forces. Entrapped cells produced 52 g/l^-1 ethanol every 24 h for many successive fermentation batches, when inoculated in batch synthetic media containing 12% glucose. It was shown that the rate of growth, ethanol production and glucose utilization increased when Al₂O₃ was added in the growth medium. This increase was dependent upon the concentration of Al₂O₃. The optimum conditions for immobilization of Z. mobilis on Al₂O₃ were established. Reduction in productivity and yield was not observed for up to 15 successive fermentation batches using the same entrapped cells.     

Immobilized xanthine oxidase: Kinetics, (in)stability,and stabilization by coimmobilization with superoxide dismutase and catalase

Milk xanthine oxidase was immobilized by covalent attachment to CNBr-activated Sepharose 4B and by adsorption to n-octylamine-substituted Sepharose 4B. The amounts of activity immobilized for the two preparations were 30 and 90%, respectively. The pH optima for free and adsorbed xanthine oxidase were at 8.6 and 8.2, respectively. Both free and immobilized xanthine oxidase show substrate inhibition. The apparent inhibition constant (K_i′) found for adsorbed xanthine oxidase with xanthine as substrate was higher than the K_i for the free enzyme, which was shown to be due to substrate diffusion limitation in the pores of the carrier beads (internal diffusion limitation). Higher substrate concentrations, as desirable for practical application in organic synthesis, can therefore be used with the immobilized enzyme without decreasing the rate. As a result of the internal diffusion limitation the apparent Michaelis constant (K_m′) for adsorbed xanthine oxidase was also higher than the K_m for the free enzyme. Immobilized xanthine oxidase was more stable than the free enzyme during storage at 4 and 30°C. Both forms rapidly lost activity during catalysis. The loss was proportional to the amount of substrate converted. Coimmobilization of xanthine oxidase with superoxide dismutase and catalase improved the operational stability, suggesting that O₂^? and H₂O₂ side-products of the enzymatic reaction were involved in the inactivation. Coimmobilization with albumin also had some stabilizing effect. Complete surrounding of xanthine oxidase by protein, however, by means of etrapment in a glutaraldehyde-crosslinked gelatin matrix, considerably enhanced the operational half-life. This system was less efficient than the Sepharose preparations either because much activity was lost during the immobilization procedure and/or because it had poor flow properties. Xanthine (15 mg)was converted by an adsorbed xanthine oxidase preparation and product (uric acid) was isolated in high yield (84%).     

Structural and Electrochemical Study of Al2O3 and TiO2 Coated Li1.2Ni0.13Mn0.54Co0.13O2 Cathode Material Using ALD

Nanolayers of Al₂O₃ and TiO₂ coatings were applied to lithium‐ and manganese‐rich cathode powder Li_1.2Ni_0.13Mn_0.54Co_0.13O₂ using an atomic layer deposition (ALD) method. The ALD coatings exhibited different surface morphologies; the Al₂O₃ surface film appeared to be uniform and conformal, while the TiO₂ layers appeared as particulates across the material surface. In a Li‐cell, the Al₂O₃ surface film was stable during repeated charge and discharge, and this improved the cell cycling stability, despite a high surface impedance. The TiO₂ layer was found to be more reactive with Li and formed a Li_xTiO₂ interface, which led to a slight increase in cell capacity. However, the repetitive insertion/extraction process for the Li⁺ ions caused erosion of the surface protective TiO₂ film, which led to degradation in cell performance, particularly at high temperature. For cells comprised of the coated Li_1.2Ni_0.13Mn_0.54Co_0.13O₂ and an anode of meso‐carbon‐micro‐beads (MCMB), the cycling stability introduced by ALD was not enough to overcome the electrochemical instability of MCMB graphite. Therefore, protection of the cathode materials by ALD Al₂O₃ or TiO₂ can address some of the capacity fading issues related to the Li‐rich cathode at room temperature.     

Reactivity of ruthenium carbonyls on metal oxide surfaces: effects of the surface acid-base chemistry

The reactivity of tetraruthenium carbonyl clusters supported on metal oxides (SiO₂, TiO₂, γ-Al₂O₃, and MgO) under various atmospheres has been investigated by infrared and ultraviolet-visible spectroscopies and electron microscopy. [H₄Ru₄(CO)₁₂] physisorbed on SiO₂ easily decomposes and aggregates to form metal particles. The tetraruthenium clusters supported on TiO₂ are oxidized by surface hydroxyl groups, giving mononuclear complexes; virtually the same chemistry occurs, but less readily, on γ-Al₂O₃. The tetramthenium clusters supported on MgO, in contrast, are highly resistant to oxidation. The strong basicity of this support leads to an increased stability of small polynuclear complexes, hindering the formation of oxidized complexes and aggregated metallic structures. The unique character of the basic support appears to be related to the tendency of the support to form and stabilize cluster anions.     

Comparative study of three magnetic nano-particles (FeSO4, FeSO4/SiO2, FeSO4/SiO2/TiO2) in plasmid DNA extraction

Recent updates on Magnetic Nano-Particles (MNPs) based separation of nucleic acids have received more attention due to their easy manipulation, simplicity, ease of automation and cost-effectiveness. It has been indicated that DNA molecules absorb on solid surfaces via hydrogen-bonding, and hydrophobic and electrostatic interactions. These properties highly depend on the surface condition of the solid support. Therefore, surface modification of MNPs may enhance their functionality and specification. In the present study, we functionalized Fe₃O₄ nano-particle surface utilizing SiO₂ and TiO₂ layer as Fe₃O₄/SiO₂ and Fe₃O₄/SiO₂/TiO₂ and then compare their functionality in the adsorption of plasmid DNA molecules with the naked Fe₃O₄ nano-particles. The result obtained showed that the purity and amount of DNA extracted by Fe₃O₄ coated by SiO₂ or SiO₂/TiO₂ were higher than the naked Fe₃O₄ nano-particles. Furthermore, we obtained pH 8 and 1.5 M NaCl as an optimal condition for desorption of DNA from MNPs. The result further showed that, 0.2 mg nano-particle and 10 min at 55 °C are the optimal conditions for DNA desorption from nano-particles. In conclusion, we recommended Fe₃O₄/SiO₂/TiO₂ as a new MNP for separation of DNA molecules from biological sources.     

Biosynthesis of Al2O3 and europium-doped Al2O3 nanoparticle using Cymbopogon citratus (lemongrass) extract and its antibacterial property

Cymbopogon citratus-mediated pure aluminium oxide (Al₂O₃) and europium (Eu)-doped Al₂O₃ with different amounts of metal ion were prepared using a green synthesis method. Synthesised nanoparticles were characterised by ultraviolet (UV)-visible spectroscopy, photoluminescence (PL), Fourier-transform infrared (FTIR) spectroscopy, X-ray diffraction (XRD) and scanning electron microscopy (SEM). Synthesis of nanoparticles is confirmed by using UV-visible spectroscopy showing maximum absorption at 411 and 345 nm for Al₂O₃ and Eu-doped Al₂O₃, respectively. The antibacterial activity of prepared nanoparticles was evaluated against Pseudomonas aeruginosa, Streptococcus aureus, Escherichia coli and Klebsiella pneumoniae using a well-diffusion technique. The effect of pure Al₂O₃ and Eu-doped nanoparticles shows excellent results against P. aeruginosa, S. aureus, E. coli and K. pneumoniae.     

Kinetic and microstructural characterization of immobilized penicillin acylase from Streptomyces lavendulae on Sepabeads EC-EP

Recombinant penicillin acylase from Streptomyces lavendulae was covalently bound to epoxy-activated Sepabeads EC-EP303®. Optimization of the immobilization process led to a homogeneous distribution of the enzyme on the support surface avoiding the attachment of enzyme aggregates, as shown by confocal electron microscopy. The optimal immobilized biocatalyst had a specific enzymatic activity of 26.2IUgwetcarrier^?1 in the hydrolysis of penicillin V at pH 8.0 and 40°C. This biocatalyst showed the highest activity at pH 8.5 and 65°C, 1.5 pH units lower and 5°C higher than its soluble counterpart. Substrate specificity of the derivative also showed its ability to efficiently hydrolyze other natural aliphatic penicillins such as penicillins K, F and dihydroF. The immobilized enzyme was highly stable at 40°C and pH 8.0 (t_1/2=625 h vs. t_1/2=397 h for the soluble enzyme), and it could be recycled for at least 30 consecutive batch reactions without loss of catalytic activity.     

Anodization of aluminum and silicon in plasma of a non-self-sustained glow discharge

The results of anodization of aluminum and silicon in an oxygen plasma are presented. The plasma was generated by a non-self-sustained glow discharge with a hollow cathode excited by an electron beam at the oxygen pressure of 20 Pa. The density of the current flowing through the anodized specimen did not exceed 1.5 mA/cm², and its temperature was 200–250°C. Continuous Al₂O₃ and SiO₂ films were formed on the aluminum and silicon surfaces. The growth rate of the oxide layers was 150–200 nm/h for Al₂O₃ and 400–800 nm/h for SiO₂.