Stress analysis of irradiated human tooth enamel using finite element methods

The objectives of this project were to use finite element methods to determine how changes in the elastic modulus due to oral cancer therapeutic radiation alter the distribution of mechanical stresses in teeth and to determine if observed failures in irradiated teeth correlate with changes in mechanical stresses. A thin slice section finite element (FE) model was constructed from micro CT sections of a molar tooth using MIMICS and 3-Matic software. This model divides the tooth into three enamel regions, the dentin-enamel junction (DEJ) and dentin. The enamel elastic modulus was determined in each region using nano indentation for three experimental groups namely – control (non-radiated), in vitro irradiated (simulated radiotherapy following tooth extraction) and in vivo irradiated (extracted subsequent to oral cancer patient radiotherapy) teeth. Physiological loads were applied to the tooth models at the buccal and lingual cusp regions for all three groups (control, in vitro and in vivo). The principal tensile stress and the maximum shear stress were used to compare the results from different groups since it has been observed in previous studies that delamination of enamel from the underlying dentin was one of the major reasons for the failure of teeth following therapeutic radiation. From the FE data, we observed an increase in the principal tensile stress within the inner enamel region of in vivo irradiated teeth (9.97 ± 1.32 MPa) as compared to control/non-irradiated teeth (8.44 ± 1.57 MPa). Our model predicts that failure occurs at the inner enamel/DEJ interface due to extremely high tensile and maximum shear stresses in in vivo irradiated teeth which could be a cause of enamel delamination due to radiotherapy.     

Aluminum concentrations in human deciduous enamel and dentin related to dental caries

The aluminum (Al) concentrations in the enamel and dentin of 314 human deciduous teeth were determined in order to examine the relationship between Al and dental caries. The sample teeth were divided into three groups: the sound tooth group, carious tooth group and filled tooth group. The teeth of the carious tooth group were further classified into three groups depending on the stage of caries. The Al content was determined using graphite furnace atomic absorption spectrometry. In both the enamel and dentin, the Al concentrations were unaffected by sex, but did depend on tooth type. In enamel, the Al concentration was significantly higher in the sound tooth group (42.8 +/- 37.3 microg/g) than in the three carious groups (20.7 +/- 17.1-24.9 +/- 22.0 microg/g) and the filled tooth group (27.3 +/- 25.5 microg/g). As for dentin, the Al concentration was also significantly higher in the sound tooth group (36.2 +/- 35.1 microg/g) than in the three carious groups (15.1 +/- 13.3-24.5 +/- 23.4 microg/g) and the filled tooth group (17.2 +/- 20.6 microg/g). Even when analyzing incisors alone, the Al concentrations were significantly higher in the sound tooth group than in the other groups, for both enamel and dentin. Furthermore, the Al levels in carious enamel and dentin did not decrease with the advance of caries. These findings indicated that the deciduous teeth containing higher Al concentrations on average had less caries than the teeth with lower Al concentrations, and suggest that Al acts as a possible cariostatic agent by itself.     

Soft Dentin Results in Unique Flexible Teeth in Scraping Catfishes

Abstract Teeth are generally used for actions in which they experience mainly compressive forces acting toward the base. The ordered tooth enamel(oid) and dentin structures contribute to the high compressive strength but also to the minor shear and tensile strengths. Some vertebrates, however, use their teeth for scraping, with teeth experiencing forces directed mostly normal to their long axis. Some scraping suckermouth catfishes (Loricariidae) even appear to have flexible teeth, which have not been found in any other vertebrate taxon. Considering the mineralized nature of tooth tissues, the notion of flexible teeth seems paradoxical. We studied teeth of five species, testing and measuring tooth flexibility, and investigating tooth (micro)structure using transmission electron microscopy, staining, computed tomography scanning, and scanning electron microscopy-energy-dispersive spectrometry. We quantified the extreme bending capacity of single teeth (up to 180°) and show that reorganizations of the tooth (micro)structure and extreme hypomineralization of the dentin are adaptations preventing breaking by allowing flexibility. Tooth shape and internal structure appear to be optimized for bending in one direction, which is expected to occur frequently when feeding (scraping) under natural conditions. Not all loricariid catfishes possess flexible teeth, with the trait potentially having evolved more than once. Flexible teeth surely rank among the most extreme evolutionary novelties in known mineralized biological materials and might yield a better understanding of the processes of dentin formation and (hypo)mineralization in vertebrates, including humans.     

预酸蚀乳牙牙本质对自酸蚀粘接系统粘接强度的影响

目的:探讨预酸蚀乳牙牙本质对自酸蚀粘接系统粘接强度的影响。方法:随机选取28颗健康乳磨牙,磨除颊舌面釉质,暴露牙本质粘接面,沿近远中向劈开形成56个样本,随机分为7组(n=8)。直接涂布组(A1组,A2组和A3组)分别涂布AdperTM Easy One(AEO),Xeno-V(XV)和OptiBond All In One(AIO)三种自酸蚀粘接剂,预酸蚀组(B1组,B2组和B3组)在涂布三种自酸蚀粘接剂前先使用35%磷酸酸蚀乳牙牙本质15 s,对照组(C组)使用Prime&Bond NTTM(NT)全酸蚀粘接剂,每个样本用Z350复合树脂堆砌成直径为3 mm的树脂小柱,通过剪切试验测试剪切粘接强度,并通过扫描电子显微镜观察断裂表面形态。结果:B1组,B2组的剪切粘接强度值明显高于A1组,A2组(P<0.001);B3组与A3组的剪切粘接强度值比较无明显差别(P=0.94)。A2组的剪切粘接强度值低于C组(P<0.05);B1组的剪切粘接强度值明显高于C组(P<0.001)。扫描电镜观察结果显示各组试件断裂面形态多为牙本质和复合树脂界面破坏。直接涂布组(A1组,A2组和A3组)断裂多发生在混合层的底部,树脂突较少且低于小管口。B1组和B2组试件断裂面可见多数牙本质小管被树脂突填满,断裂多发生在混合层的中上部。B3组试件断裂面可见牙本质小管空虚,树脂突较少。结论:预酸蚀乳牙牙本质可以提高AEO,XV两种自酸蚀粘接剂的剪切粘接强度。自酸蚀粘接剂处理乳牙牙本质可以达到全酸蚀粘接剂处理的粘接强度,但应用自酸蚀粘接剂前预酸蚀乳牙牙本质可以获得更高的粘接强度。     

Punch shear testing of extracted vital and endodontically treated teeth

Plano-parallel specimens of human dentin cut from vital and endodontically treated teeth were tested by the punch shear test. Shear strength values were found to positively correlate with approximate toughness values. Statistically significant differences were found between shear strength and toughness values for vital and endodontically treated teeth, the latter showing lower values. The clinical impression that endodontically treated teeth are weaker and more brittle than vital teeth has therefore been quantitated. Anatomically different teeth or the methods used to store and cut teeth could not be consistently correlated with punch shear and toughness values. When dentin slices were constrained during punching so that bending was prevented, the precision of the results was improved and higher values were recorded.     

Finite element analysis of anterior tooth root stresses developed during endodontic treatment

Vertical tooth root fractures are diagnostically challenging, frustrating, and an increasingly common cause of failure of tooth restoration. These vertical root fractures have been associated with many causes, including the endodontic process itself. To investigate these endodontic causes, various phases of crown replacement for an anterior tooth were modeled using nonlinear, plane strain finite element (FE) analysis. Stresses developed during obturation, post positioning, crown placement, and masticatory and occlusal loading of the restored tooth were estimated using this analysis method. The minimum (compressive) principal stress was greatest during obturation of cones 1 and 2, and during mastication of the restored tooth. Although these stresses were significant (-150 to -280 MPa), they did not exceed the compressive strength of dentin. The maximum (tensile) principal stresses, 160 to 300 MPa, were also observed during obturation of cones 1 and 2. These peak stresses exceed the dentin tensile strength.     

Development of the dentition in Alligator mississippiensis: upper jaw dental and craniofacial development in embryos, hatchlings, and young juveniles, with a comparison to lower jaw development

Development of the upper dentition in Alligator mississippiensis was investigated using a close series of accurately staged and aged embryos, hatchlings, and young juveniles up to 11 days posthatching, as well as some young and old adult specimens. Studies from scanning electron microscopy, light microscopy, acetate and computer reconstructions, radiography and macroscopy were combined to elucidate the details of embryonic dental development, tooth initiation pattern, dentitional growth, and erupted functional dentition. The results were compared with those from the lower jaw and related to the development of other craniofacial structures. Approximately 17 early teeth in each jaw half develop as surface teeth, of which 13 project for 1 to 12 days before sinking into the mesenchyme. The first three teeth initiate directly from the oral epithelium at Ferguson stages 14-15 (days 15-19 after egg laying), before there is any local trace of dental lamina formation. All other teeth develop from a dental prolamina or lamina; and with progressive lamina development, submerged teeth initiate from the aboral end leading to the formation of replacement teeth. All teeth form dentin matrix, but 12 early teeth do not form enamel. Approximately 20 embryonic teeth are resorbed, 6 are transitional, and 42 function for longer periods after hatching. The embryonic tooth initiation pattern (illustrated by defining a tooth position formula) does not support the previous models of Odontostichi, Zahnreihen, and Tooth Families, each of which postulates perfect regularity. Up to three interstitial tooth positions develop between sites of primary tooth initiation, and families with up to five generations at hatching are at first arbitrarily defined.     

Apoptosis in developmental and repair-related human tooth remodeling: a view from the inside

Apoptosis is a key phenomenon in the regulation of the life span of odontoblasts, which are responsible for dentin matrix production of the teeth. The mechanism controlling odontoblasts loss in developing, normal, and injured human teeth is largely unknown. A possible correlation between apoptosis and dental pulp volume reduction was examined. Histomorphometric analysis was performed on intact 10 to 14 year-old premolars to follow dentin deposition and evaluate the total number of odontoblasts. Apoptosis in growing healthy teeth as well as in mature irritated human teeth was determined using a modified TUNEL technique and an anti-caspase-3 antibody. In intact growing teeth, the sequential rearrangement of odontoblasts into a multi-layer structure during tooth crown formation was correlated with an apoptotic wave that leads to the massive elimination of odontoblasts. These data suggest that apoptosis, coincident with dentin deposition changes, plays a role in tooth maturation and homeostasis. Massive apoptotic events were observed after dentin irritation. In carious and injured teeth, apoptosis was detected in cells surrounding the lesion sites, as well as in mono-nucleated cells nearby the injury. These results indicate that apoptosis is a part of the mechanism that regulate human dental pulp chamber remodeling during tooth development and pathology.     

Immunodetection of osteopontin at sites of resorption in the pulp of rat molars.

Osteopontin (OPN) has been proposed to act as a substrate for osteoclast adhesion during bone resorption. The aim of the present study was to examine the presence and distribution of OPN at sites of resorption in traumatized radicular pulp. The upper first molars of 6-week-old male Sprague-Dawley rats were luxated and then repositioned in the original sockets. The animals were sacrificed by intracardiac perfusion at 10 and 14 days after tooth reimplantation. The teeth were decalcified in EDTA and then processed for embedding in paraffin for histochemistry or LR White resin for immunocytochemistry. Odontoclasts were identified by their multinucleated morphology and expression of tartrate-resistant acid phosphatase (TRAP). Osteopontin was immunolocalized using postembedding colloidal gold labeling with a chicken egg yolk anti-rat OPN antibody. After reimplantation of the teeth, TRAP-positive cells were present along the pulp dentin wall. Osteopontin was not consistently detected at exposed predentin/dentin surfaces. However, gold particles were often found at the margin of resorption lacunae. Labeling was also seen over the Golgi region and cytoplasmic vesicles of odontoclasts and of neutrophils and fibroblast-like cells. The results suggest that accumulation of OPN at the predentin/dentin surface is not a prerequisite for adhesion of odontoclasts to the wall substance and that recruited odontoclasts produce OPN locally to mediate cell and/or matrix events within the resorption lacuna.     

Shear Bond Strength and Fracture Analysis of Human vs. Bovine Teeth

Purpose

To evaluate if bovine enamel and dentin are appropriate substitutes for the respective human hard tooth tissues to test shear bond strength (SBS) and fracture analysis.

Materials and Methods

80 sound and caries-free human erupted third molars and 80 freshly extracted bovine permanent central incisors (10 specimens for each group) were used to investigate enamel and dentine adhesion of one 2-step self-etch (SE) and one 3-step etch and rinse (E&R) product. To test SBS the buccal or labial areas were ground plane to obtain appropriate enamel or dentine areas. SE and E&R were applied and SBS was measured prior to and after 500 thermocycles between +5 and +55°C. Fracture analysis was performed for all debonded areas.

Results

ANOVA revealed significant differences of enamel and dentin SBS prior to and after thermocycling for both of the adhesives. SBS- of E&R-bonded human enamel increased after thermocycling but SE-bonded did not. Bovine enamel SE-bonded showed higher SBS after TC but E&R-bonded had lower SBS. No differences were found for human dentin SE- or E&R-bonded prior to or after thermocycling but bovine dentin SE-bonded increased whereas bovine dentine E&R-bonded decreased. Considering the totalized and adhesive failures, fracture analysis did not show significances between the adhesives or the respective tooth tissues prior to or after thermocycling.

Conclusion

Although SBS was different on human and bovine teeth, no differences were found for fracture analysis. This indicates that solely conducted SBS on bovine substrate are not sufficient to judge the perfomance of adhesives, thus bovine teeth are questionnable as a substrate for shear bond testing.     

The cytology of submandibular glands of the opossum

Tooth attachment in the majority of the bony fish is by ankylosis or fibrous membrane. However, in one group of the osteichthys, the trigger-fish or balistids, tooth attachment is by means of a periodontium composed of a shallow alveolar socket, a periodontal ligament and acellular cementum. Histologically, the balistid periodontal ligament is composed of a dense fibro-cellular connective tissue possessing an abundance of typical fibrocytes, collagen fiber bundles, and oxytalan fibers. The collagen fiber bundles which resemble the principal fiber bundles of the mammalian periodontal ligament are inserted into the bone of the shallow alveolar sockets and are anchored to the teeth by means of a layer of amorphous acellular cementum that covers the radicular dentin. No cementoblasts were found in functional teeth, and epithelial rests are lacking. The mid-central zone of the balistid periodontal ligament is occupied by small blood vessels.     

Structure of the radially asymmetrical uncalcified region of the teeth of the red-backed salamander,Plethodon cinereus (Amphibia,Plethodontidae)

The teeth of the adult plethodontid salamander, Plethodon cinereus, were examined by light and electron microscopy with emphasis on the ringlike zone of uncalcified dentin that divides the calcified portion of each tooth into a proximal pedestal and a distal apex. The uncalcified region displays radial asymmetry, forming an integral part of the posterior wall of the tooth but bulging into the pulp cavity anteriorly, thus forming a hingelike structure. All portions of the dentin, including the uncalcified region, are composed predominantly of collagenous fibers but lack elastin. In scanning electron micrographs of teeth from which the oral mucosa has been removed, the location of the anterior uncalcified hinge is marked externally by a notch-like articulation of the apex and pedestal. Sites of transition between calcified and uncalcified areas of the dentin show no special modifications in transmission electron micrographs, but collagenous fibers in calcified portions are associated with more electron-dense amorphous material than are those in the uncalcified region. Odontoblasts associated with the uncalcified region possess ultrastructural features closely resembling those of odontoblasts found in calcified areas. The uncalcified region seems to afford the teeth a certain degree of flexibility, and the asymmetry of the region appears to allow the teeth to flex only in a posterior direction, thus facilitating the entry of living prey but hindering its escape. The uncalcified region also seems to permit the apex of a tooth to break away from its pedestal without damage to underlying bone.     

Morphological variations in a tooth family through ontogeny in Pleurodeles waltl (Lissamphibia, Caudata)

Most nonmammalian species replace their teeth continuously (so-called polyphyodonty), which allows morphological and structural modifications to occur during ontogeny. We have chosen Pleurodeles waltl, a salamander easy to rear in the laboratory, as a model species to establish the morphological foundations necessary for future molecular approaches aiming to understand not only molecular processes involved in tooth development and replacement, but also their changes, notably during metamorphosis, that might usefully inform studies of modifications of tooth morphology during evolution. In order to determine when (in which developmental stage) and how (progressively or suddenly) tooth modifications take place during ontogeny, we concentrated our observations on a single tooth family, located at position I, closest to the symphysis on the left lower jaw. We monitored the development and replacement of the six first teeth in a large growth series ranging from 10-day-old embryos (tooth I1) to adult specimens (tooth I6), using light (LM), scanning (SEM), and transmission electron (TEM) microscopy. A timetable of the developmental and functional period is provided for the six teeth, and tooth development is compared in larvae and young adults. In P. waltl the first functional tooth is not replaced when the second generation tooth forms, in contrast to what occurs for the later generation teeth, leading to the presence of two functional teeth in a single position during the first 2 months of life. Larval tooth I1 shows dramatically different features when compared to adult tooth I6: a dividing zone has appeared between the dentin cone and the pedicel; the pulp cavity has enlarged, allowing accommodation of large blood vessels; the odontoblasts are well organized along the dentin surface; tubules have appeared in the dentin; and teeth have become bicuspidate. Most of these modifications take place progressively from one tooth generation to the next, but the change from monocuspid to bicuspid tooth occurs during the tooth I3 to tooth I4 transition at metamorphosis.     

Enamel dictates whole tooth deformation: A finite element model study validated by a metrology method

In order to understand whole tooth behavior under load the biomechanical role of enamel and dentin has to be determined. We approach this question by comparing the deformation pattern and stiffness of intact teeth under load with the deformation pattern and stiffness of the same teeth after the enamel has been mechanically compromised by introducing a defect. FE models of intact human premolars, based on high resolution micro-CT scans, were generated and validated by in vitro electronic speckle pattern interferometry (ESPI) experiments. Once a valid FE model was established, we exploit the flexibility of the FE model to gain more insight into whole tooth function. Results show that the enamel cap is an intrinsically stiff biological structure and its morphology dictates the way a whole tooth will mechanically behave under load. The mechanical properties of the enamel cap were sufficient to mechanically maintain almost its entire stiffness function under load even when a small defect (cavity simulating caries) was introduced into its structure and breached the crown integrity. We conclude that for the most part, that enamel and not dentin dictates the mechanical behavior of the whole tooth.     

MTA、iRoot BP Plus及氢氧化钙在年轻恒牙活髓切断术中临床疗效的比较分析

摘要 目的：研究三氧化矿物凝聚体（MTA）、iRoot BP Plus（iRooT）以及氢氧化钙（Ca(OH) ₂）三种材料在年轻恒牙活髓切断术中的临床疗效。方法：将60例需要接受年轻恒牙活髓切断术的患者（60颗患牙）按照使用材料不同随机分为三组：MTA组、iRooT组和Ca（OH）₂组,每组20例（20颗患牙）,比较三组患者术后3个月和6个月手术成功率、牙本质桥形成和牙齿变色发生率、牙根管壁厚度、牙齿功能和美观度、以及血清基质金属蛋白酶-3（MMP-3）和白细胞介素-8（IL-8）水平。结果：（1）三组患者仅术后6个月临床治疗成功率存在显著差异（P<0.05）;（2）Ca（OH）₂组术后牙本质桥形成率显著低于其他两组（P<0.05）,而牙齿变色发生率显著低于MTA组（P<0.05）和显著高于iRooT组（P<0.05）。（3）三组患者治疗后牙根管壁厚度均较治疗前显著增加,且治疗后Ca（OH）₂组患牙根管壁厚度增加显著低于MTA组和iRooT组（P<0.05）。（4）Ca（OH）2组患者术后6个月牙齿舒适功能、固定功能和咀嚼功能评分均显著低于MTA组和iRooT组（P<0.05）,而牙齿美观度评分显著低于iRooT组（P<0.05）和显著高于MTA组（P<0.05）。（5）三组患者术后6个月血清MMP-3和IL-8均显著低于术前（P<0.05）,并且MTA组患者血清MMP-3和IL-8水平显著高于iRooT组（P<0.05）和显著低于CaOH组（P<0.05）。结论：iRoot BP Plus和MTA材料应用于年轻恒牙活髓切断术均具有较高的远期成功率,但MTA材料远期牙齿变色率较高因而影响牙齿美观度。     

An experimental approach to modeling the strength of canine teeth

The strength of canine teeth in several carnivores is found through direct fracture experiments. The average forces required to break the canines of adult animals are coyote 1170 N, red fox 533 N, bobcat 737 N and raccoon 512 N. Stresses created in teeth at the breaking load are predicted by finite-element analysis and beam theory. The ultimate tensile stress sustainable in these teeth is 338 MPa in adult animals. The large pulp cavity in the canines of young animals significantly weakens the bases of their teeth (by about 25%), but as the animal ages the pulp cavity decreases and has little effect on overall tooth strength. The tooth material of young of the year is significantly weaker than that from older animals (by about 35%). With the experimentally derived ultimate tensile stress, finite-element analysis can estimate the breaking load of canines for several carnivores. A significant allometric relationship exists between log of body weight and log of strength of tooth (slope=0.81).     

Age-Related Changes in Functional Teeth in the Pacific Walrus (<Emphasis Type="Italic">Odobenus rosmarus divergens</Emphasis>)

We examined functional teeth (except for upper canine teeth) of Pacific walruses that died or were harvested on the coast of the Chukchi Peninsula in 2005, 2007–2008, and 2010–2011. The dynamics of deposition of annual cement layers was investigated. The rate of cement deposition on the walls of tooth roots decreased significantly with age. The rate of its deposition on the lingual side of the upper teeth was much higher than that on their buccal side, but no such differences were observed on the lower teeth. The same cement layer was deposited unevenly in different parts of teeth (on its different sides and levels) with a general tendency of increasing in the width of the layer from the top to the lower parts of teeth. As a result of local widening of some cement layers with age, the tooth surface became rough, and knolls and rollers appeared there. As the age increased, external changes in teeth occurred: they became larger, more rounded, and heavier. We described a method for the preliminary determination of the relative age of walruses based on the ratio between the width of cement and dentin on the attrition surface of lower teeth (without cutting).     

The influence of the root cross-section on the stress distribution in teeth restored with a positive-locking post and core design: a finite element study

Human teeth with substantial coronal defects are subject to reconstruction by means of post and core restorations. Typically, such a restoration comprises a slightly cylindrical post onto which an abutment of varying shape, depending on the designated restoration, is attached. As clinical results are not satisfactory to date, we proposed a new proprietary post and core design which makes use of positive locking. As this prefabricated system is not customised to an individual root's cross-sectional geometry (usually oval), a varying amount of radicular dentin is left in periphery of the core's outer edge. The aim of this study was to assess the implications of this fact, i.e., whether the root has to endure higher overall stress levels which ultimately may lead to failure of one of the components involved. A series of finite element simulations were performed to evaluate stress and strain on the system, in which the proposed post and core was embedded into a virtual dentin cylinder of different diameters, ranging from flush mounting of the restoration to a dentin excess of 4 mm, and subsequently loaded with forces with two angles of attack (90 degrees and 130 degrees ). The results show that flush mounting yields an agreeable stress and strain distribution within the radicular dentin, but overall stress levels drop significantly with an excess of 0.5 mm of surrounding dentin. More than 1 mm excess was not found to have profound positive effects.     

Effect of repeated microwave disinfections on bonding of different commercial teeth to resin denture base

doi: 10.1111/j.1741‐2358.2011.00516.x Effect of repeated microwave disinfections on bonding of different commercial teeth to resin denture base Objective: To verify the influence of repeated microwave disinfections on the shear bond strength of two commercial types of teeth to acrylic resin, when the ridge lap surfaces were unmodified, bur abraded, bur grooved or etched by monomer. Material and methods: Eighty specimens (n = 10) were adhered to the tooth ridge lap surface, polymerised in a water bath at 74°C for 9 h. Microwaved specimens were individually immersed in 150 ml of water and submitted to five simulated disinfections in a microwave oven calibrated at 650 W for 3 min. Control specimens were not microwave treated. Shear bond strength tests were performed in an Instron machine with a cross‐speed of 1 mm/min. The fracture load values were transformed into shear bond strength as a function of the bonding area (0.28 cm²). Data were submitted to anova and Tukey’s test (α = 0.05). Fractured areas were classified as adhesive, cohesive (resin or tooth) or mixed failures. Results: Repeated microwave disinfections increased the shear strength of the tooth/resin bond. Mechanical retention in microwaved and non‐microwaved procedures improved the shear bond strength. Conclusions: The different commercial types of teeth influenced shear bond strength values, with Biotone teeth showing the lower values.     

Effect of microwave treatment on the shear bond strength of different types of commercial teeth to acrylic resin

doi:10.1111/j.1741‐2358.2009.00333.x
Effect of microwave treatment on the shear bond strength of different types of commercial teeth to acrylic resin Objective: The purpose of this study was to verify the effect of microwave treatment on the shear bond strength of commercial types of teeth to acrylic resin, when the glossy ridge laps were unmodified (groups 1 and 5), bur abraded (groups 2 and 6), bur grooved (groups 3 and 7) or etched by monomer (groups 4 and 8). Background: Controversial findings have shown that mechanical or chemical changes in ridge‐lap surface of the tooth increase or decrease the bond strength between tooth and acrylic resin, and the microwave disinfection may cause different changes on this bond strength. Materials and methods: Eighty specimens (n = 10) were made with the acrylic resin bonded to tooth glossy ridge lap, polymerised in water at 74°C for 9 h, and deflasked after flask cooling. Specimens of the groups 5, 6, 7 and 8 were individually immersed in 150 ml of water and submitted to microwave treatment in an oven at 650 W for 3 min. Control specimens (groups 1, 2, 3 and 4) were not microwave treated. Shear bond strength test was performed in an Instron machine with a cross‐speed of 1 mm/min. Collected data were submitted to anova and Tukey’s test (α = 0.05). Results: Microwave treatment decreased the shear bond strength values of the tooth/resin bond. In the microwaved and non‐microwaved procedures, mechanical retention improved the shear bond strength when compared with the control and monomer treatments. Conclusion: Shear bond strength of the tooth/resin bond was influenced by the microwave treatment and different commercial teeth association, and was lower for the Biotone tooth.