Rapid start-up and performance of denitrifying granular sludge in an upflow sludge blanket (USB) reactor treating high concentration nitrite wastewater

Denitrifying granular sludge reactor holds better nitrogen removal efficiency than other kinds of denitrifying reactors, while this reactor commonly needs seeding anaerobic granular sludge and longer period for start-up in practice, which restricted the application of denitrifying granular sludge reactor. This study presented a rapid and stable start-up method for denitrifying granular sludge. An upflow sludge blanket (USB) reactor with packings was established with flocculent activated sludge for treatment of high concentration nitrite wastewater. Results showed mature denitrifying granular sludge appeared only after 15 days with highest nitrogen removal rate of 5.844 kg N/(m³ day), which was much higher than that of compared anoxic sequencing batch reactor (ASBR). No significant nitrite inhibition occurred in USB and denitrification performance was mainly influenced by hydraulic retention time, influent C/N ratio and internal reflux ratio. Hydraulic shear force created by upflow fluid, shearing of gaseous products and stable microorganisms adhesion on the packings might be the reasons for rapid achievement of granular sludge. Compared to inoculated sludge and ASBR, remarkable microbial communitiy variations were detected in USB. The dominance of Proteobacteria and Bacteroidetes and enrichment of species Pseudomonas_stutzeri should be responsible for the excellent denitrification performance, which further verified the feasibility of start-up method.     

Start-up of the Anammox process in a membrane bioreactor

The start-up of an Anammox process was studied in a membrane sequencing batch reactor (MSBR) in which a submerged hollow fibre membrane module was used to retain the biomass. The reactor was seed with Anammox biomass and fed using the Van de Graaf medium. During a first operating stage, salt precipitation was observed and interfered with microbial activity and caused a decrease of the nitrogen removal rate of the reactor from 100 to only 10 mgl(-1) per day. Salt precipitation was avoided by diminishing adequately the Ca and P concentrations of the Van de Graaf medium during the last operating stage. This action increased quickly the activity of the system, and nitrogen removal rate reached up to 710 mgl(-1) per day with almost full nitrite removal. Sporadic flotation of the sludge was observed in the MSBR. The use of the membrane avoided biomass wash-out from the system. Moreover, a surprising fact was that Anammox biomass did not grow in flocs in the MSBR, but in granules. This fact showed that this kind of microorganisms have a trend to grow in aggregates. Results indicated that the use of the MSBR could be a suitable system for nitrogen removal by using the Anammox reaction.     

Start-up and stabilization of an Anammox process from a non-acclimatized sludge in CSTR

Development of an Anammox (anaerobic ammonium oxidation) process using non-acclimatized sludge requires a long start-up period owing to the very slow growth rate of Anammox bacteria. This article addresses the issue of achieving a shorter start-up period for Anammox activity in a well-mixed continuously stirred tank reactor (CSTR) using non-acclimatized anaerobic sludge. Proper selection of enrichment conditions and low stirring speed of 30 ± 5 rpm resulted in a shorter start-up period (82 days). Activity tests revealed the microbial community structure of Anammox micro-granules. Ammonia-oxidizing bacteria (AOB) were found on the surface and on the outer most layers of granules while nitrite-oxidizing bacteria (NOB) and Anammox bacteria were present inside. Fine-tuning of influent NO₂ ⁻/NH₄ ⁺ ratio allowed Anammox activity to be maintained when mixed microbial populations were present. The maximum nitrogen removal rate achieved in the system was 0.216 kg N/(m³ day) with a maximum specific nitrogen removal rate of 0.434 g N/(g VSS day). During the study period, Anammox activity was not inhibited by pH changes and free ammonia toxicity.     

Reactivation of effluent granular sludge from a high-rate Anammox reactor after storage

In this study, effluent sludge from a high-rate Anammox reactor was used to re-start new Anammox reactors for the reactivation of Anammox granular sludge. Different start-up strategies were evaluated in six upflow anaerobic sludge blanket (UASB) reactors (R₁–R₆) for their effect on nitrogen removal performance. Maximal nitrogen removal rates (NRRs) greater than 20 kg N/m³/day were obtained in reactors R₃–R₅, which were seeded with mixed Anammox sludge previously stored for approximately 6 months and 1 month. A modified Boltzmann model describing the evolution of the NRR fit the experimental data well. An amount of sludge added to the UASB reactor or decreasing the loading rate proved effective in relieving the substrate inhibition and increasing the NRR. The modified Stover–Kincannon model fit the nitrogen removal data in the Anammox reactors well, and the simulation results showed that the Anammox process has great nitrogen removal potential. The observed inhibition in the Anammox reactors may have been caused by high levels of free ammonia. The sludge used to seed the reactors did not settle well; sludge flotation was observed even after the reactors were operated for a long time at a floating upward velocity (F_s) of greater than 100 m/h. The settling sludge, however, exhibited good settling properties. Scanning electron microscopy showed that the Anammox granules consisted mainly of spherical and elliptical bacteria with abundant filaments on their surface. Hollows in the granules were also present, which may have contributed to sludge floatation.     

Start-up and inhibition analysis of the Anammox process seeded with anaerobic granular sludge

The longer start-up period of the Anammox process is due to the very low cellular yield and growth rates of Anammox bacteria. Nitrite inhibition is considered to be the key factor in the instability of the Anammox process during the operation. However, little attention was paid to the inhibitory effect of pH and free ammonia. This paper presents start-up and inhibition analysis of an Anammox biofilm reactor seeded with anaerobic granular sludge. Results showed that the start-up period could be divided into the sludge lysis phase, lag phase, propagation phase, stationary phase and inhibition phase. Optimization control could be implemented correspondingly to accelerate the start-up of Anammox bioreactors. Effluent pH increased to 8.7–9.1 when the nitrogen removal rate was higher than 1,200 mg l⁻¹ day⁻¹. The free ammonia concentration was accompanied with a higher level of 64–73 mg l⁻¹. Inhibitory effects of high pH and free ammonia on Anammox bacteria contributed to the destabilization of the Anammox bioreactor during the first 125 days with influent KHCO₃ of 0.5 g l⁻¹. Increasing the suffering capacity in the inlet by dosing 1.25 g KHCO₃ l⁻¹ effectively reduced the pH variation, and the nitrogen removal performance of the reactor was further developed.     

Anammox反应器启动过程中颗粒污泥性状变化特性

以厌氧颗粒污泥作为接种物,通过185 d的运行,成功启动了上流式厌氧氨氧化污泥床(Upflow anaerobic sludge blanket,UASB)反应器。反应器的进水氨氮与亚硝氮浓度分别提升至224 mg/L和255 mg/L,容积氮去除速率提升至3.76 kg/(m3·d)。采用红外光谱、扫描电镜和透射电镜等对厌氧氨氧化颗粒污泥的性状进行观察,发现颗粒污泥在启动过程中经历了污泥颗粒裂解到污泥颗粒重组的过程,且厌氧氨氧化颗粒污泥表面含有丰富的官能团,说明厌氧氨氧化颗粒污泥可能具有良好的吸附性能。采用宏基因组测序的方法对启动前后颗粒污泥的生态结构进行分析,发现原接种污泥优势菌群(变形菌门、厚壁菌门、拟杆菌门)丰度大幅减少,厌氧氨氧化菌所属的浮霉状菌门丰度则由1.59%提升到23.24%。     

流加菌种对厌氧氨氧化工艺的影响

厌氧氨氧化工艺具有很高的容积氮去除速率,现已成功应用于污泥压滤液等含氨废水的脱氮处理,容积氮去除速率高达9.5 kg/(m3·d)。但由于厌氧氨氧化菌为自养型细菌,生长缓慢,对环境条件敏感,致使厌氧氨氧化工艺启动时间过长,运行容易失稳,并且不适合处理有机含氨废水和毒性含氨废水,极大地限制了该工艺的进一步推广应用。为了克服厌氧氨氧化工艺实际应用中存在的问题,结合发酵工业中常用的菌种流加技术,提出了一种新型的菌种流加式厌氧氨氧化工艺,研究了该新型工艺在厌氧氨氧化工艺的启动过程、稳定运行以及处理有机含氨废水和毒性含氨废水等方面的应用情况。结果表明,通过向反应器内补加优质厌氧氨氧化菌种,可提高厌氧氨氧化菌数量及其在菌群中的比例,强化厌氧氨氧化功能。据此研发的菌种流加式厌氧氨氧化工艺不仅可以实现快速启动,而且可以稳定运行,并突破了有机物和毒物所致的运行障碍,拓展了厌氧氨氧化工艺的应用范围。     

Anammox反应器启动前后微生物群落结构差异性

接种A^2/O回流污泥启动Anammox-UASB反应器,研究了上升流速对系统脱氮性能影响,利用高通量测序对反应器中微生物群落结构变化进行了研究。结果表明,历时35 d成功启动Anammox反应器。上升流速升高可以明显促进脱氮效果,在最佳上升流速为1.14 m/h时TN去除率达84.74%,去除速率高达0.766 gTN/(L·d)。高通量分析表明,Anammox污泥群落Alpha多样性较接种污泥明显减少,Anammox污泥中的Anammox菌主要为Candidatus Jettenia和Candidatus Brocadia两个属,同时检测到大量的其他脱氮微生物菌属,系统中这些脱氮微生物的大量增值使系统脱氮能力逐步提高。     

The effect of pretreatment on anaerobic activity of olive mill wastewater using batch and continuous systems

This study was focused on several physico-chemical and biological treatment methods that may affect the reduction of the organic load in olive mill wastewater (OMW). In this study, removal of 95% of the phenolic compounds present in OMW was achieved using sand filtration and subsequent treatment with powdered activated carbon in a batch system. This pretreatment for OMW was found to enhance the anaerobic activity of the sludge in the batch system significantly. The efficiency of organic load removal achieved by the anaerobic treatment of untreated OMW in batch reactors with tap water dilution factors below 1:10, reached approximately 65% chemical oxygen demand (COD) removal. However, in the up-flow sludge anaerobic blanket (UASB) reactor, COD removal efficiency of 80–85% was reached at a hydraulic retention time (HRT) of 5 days with an influent COD concentration of 40 g l⁻¹ and organic loading rate (OLR)=8 g⁻¹ COD l⁻¹ per day.     

三种接种物启动Anammox-EGSB反应器的性能

为了优选接种物和加速Anammox反应器启动,分别以厌氧产甲烷污泥 (Anaerobic methanogenic sludge,AMS)、新鲜厌氧氨氧化污泥 (Fresh Anammox sludge,FAS) 和储藏厌氧氨氧化污泥 (Stored Anammox sludge,SAS) 作为接种物,研究了厌氧氨氧化膨胀颗粒污泥床 (Anammox-EGSB) 反应器 (R1、R2和R3) 的启动性能。结果表明：3种接种物均能成功启动Anammox-EGSB反应器,启动性能的优劣次序为：R2 (接种物为     

Treatment of old landfill leachate with high ammonium content using aerobic granular sludge

Background

Aerobic granular sludge has become an attractive alternative to the conventional activated sludge due to its high settling velocity, compact structure, and higher tolerance to toxic substances and adverse conditions. Aerobic granular sludge process has been studied intensively in the treatment of municipal and industrial wastewater. However, information on leachate treatment using aerobic granular sludge is very limited.

Methods

This study investigated the treatment performance of old landfill leachate with different levels of ammonium using two aerobic sequencing batch reactors (SBR): an activated sludge SBR (ASBR) and a granular sludge SBR (GSBR). Aerobic granules were successfully developed using old leachate with low ammonium concentration (136 mg L^?1 NH₄ ⁺-N).

Results

The GSBR obtained a stable chemical oxygen demand (COD) removal of 70% after 15 days of operation; while the ASBR required a start-up of at least 30 days and obtained unstable COD removal varying from 38 to 70%. Ammonium concentration was gradually increased in both reactors. Increasing influent ammonium concentration to 225 mg L^?1 N, the GSBR removed 73 ± 8% of COD; while COD removal of the ASBR was 59 ± 9%. The GSBR was also more efficient than the ASBR for nitrogen removal. The granular sludge could adapt to the increasing concentrations of ammonium, achieving 95 ± 7% removal efficiency at a maximum influent concentration of 465 mg L^?1 N. Ammonium removal of 96 ± 5% was obtained by the ASBR when it was fed with a maximum of 217 mg L^?1 NH₄ ⁺-N. However, the ASBR was partially inhibited by free-ammonia and nitrite accumulation rate increased up to 85%. Free-nitrous acid and the low biodegradability of organic carbon were likely the main factors affecting phosphorus removal.

Conclusion

The results from this research suggested that aerobic granular sludge have advantage over activated sludge in leachate treatment.

     

Effect of influent COD/N ratio on biological nitrogen removal (BNR) from high-strength ammonium industrial wastewater

The effect of influent COD/N ratio on biological nitrogen removal (BNR) from high-strength ammonium industrial wastewater was investigated. Experiments were conducted in a modified Ludzack–Ettinger pilot-plant configuration for 365 days. Total nitrification of an influent concentration of 1200 mg NH₄⁺–N l⁻¹ was obtained in this period. Influent COD/N ratios between 0.71 and 3.4 g COD g N⁻¹ were tested by varying the nitrogen loading rate (NLR) supplied to the pilot plant. An exponential decrease of nitrification rate was observed when the influent COD/N ratio increased.

The experimental COD/N ratio for denitrification was 7.1±0.8 g COD g N⁻¹ while the stoichiometric ratio was 4.2 g COD g N⁻¹. This difference is attributable to the oxidation of organic matter in the anoxic reactor with the oxygen of the internal recycle. The influence of influent COD/N ratio on the treatment of high-strength ammonium industrial wastewater can be quantified with these results. The influence of COD/N ratio should be one of the main parameters in the design of biological nitrogen removal processes in industrial wastewater treatment.     

Enrichment and granulation of Anammox biomass started up with methanogenic granular sludge

A sequencing batch reactor (SBR) seeded with methanogenic granular sludge was started up to enrich Anammox (Anaerobic Ammonium Oxidation) bacteria and to investigate the feasibility of granulation of Anammox biomass. Research results showed that hydraulic retention time (HRT) was an important factor to enrich Anammox bacteria. When the HRT was controlled at 30 days during the initial cultivation, the SBR reactor presented Anammox activity at t = 58 days. Simultaneously, the methanogenic granular sludge changed gradually from dust black to brown colour and its diameter became smaller. At t = 90 days, the Anammox activity was further improved. NH₄⁺-N and NO₂⁻N were removed simultaneously with higher speed and the maximum removal rates reached 14.6 g NH₄⁺-N /(m³ _reactor·day) and 6.67 g NO₂⁻-N /(m³ _reactor·day), respectively. Between t = 110 days and t = 161 days, the nitrogen load was increased to a HRT of 5 days (70 mg/l NH₄⁺ and 70 mg/l NO₂), the removal rates of ammonium and nitrite were 60.6% and 62.5% respectively. The sludge changed to red and formed Anammox granulation with high nitrogen removal activity.     

Assessment of partial nitrification reactor performance through microbial population shift using quinone profile, FISH and SEM

In engineered systems, biological nitrogen removal through partial nitrification to nitrite is of great interest. Accordingly, effect of operating parameters such as pH, DO and temperature on the accumulation of ammonia-oxidizers was investigated. pH of 8, DO of 0.3-0.5mg/l and temperature of 35 degrees C yielded a ratio of 0.9-1.5 of NO(2)N:NH(4)N in the effluent suitable as a feed for Anammox reactor. Microbial population shift during start-up was assessed using quinone profile, SEM and FISH. UQ-8 in the biomass, which is the predominant quinone in ammonia-oxidizers, increased from 24.8% on Day 1 to 61.2% on Day 136. Fluorescence in situ hybridization analysis in the reactor showed that ammonia-oxidizing bacteria gradually outcompeted other bacteria and was the dominant population. The morphology and inner structure of the granular sludge was observed using SEM and the photographs indicated that the aerobic granular sludge showed a shift towards spherical and small rod-shaped clusters.     

Achieving nitrite accumulation in a continuous system treating low-strength domestic wastewater: switchover from batch start-up to continuous operation with process control

Although biological nitrogen removal via nitrite is recognized as one of the cost-effective and sustainable biological nitrogen removal processes, nitrite accumulation has proven difficult to achieve in continuous processes treating low-strength nitrogenous wastewater. Partial nitrification to nitrite was achieved and maintained in a lab-scale completely stirred tank reactor (CSTR) treating real domestic wastewater. During the start-up period, sludge with ammonia-oxidizing bacteria (AOB) but no nitrite-oxidizing bacteria (NOB) was obtained by batch operation with aeration time control. The nitrifying sludge with the dominance of AOB was then directly switched into continuous operation. It was demonstrated that partial nitrification to nitrite in the continuous system could be repeatedly and reliably achieved using this start-up strategy. The ratio of dissolved oxygen to ammonium loading rate (DO/ALR) was critical to maintain high ammonium removal efficiency and nitrite accumulation ratio. Over 85% of nitrite accumulation ratio and more than 95% of ammonium removal efficiency were achieved at DO/ALR ratios in an optimal range of 4.0–6.0 mg O₂/g N d, even under the disturbances of ammonium loading rate. Microbial population shift was investigated, and fluorescence in situ hybridization analysis indicated that AOB were the dominant nitrifying bacteria over NOB when stable partial nitrification was established.     

Effects of mechanical stress on Anammox granules in a sequencing batch reactor (SBR)

The effect of shear stress on Anammox process was studied in a sequencing batch reactor (SBR). The reactor was operated during 218 days under different stirring speeds (60-250 rpm) in order to expose the system to different shear conditions and to study the stability of the Anammox granules referred to their biological activity and size. The nitrogen loading rate (NLR) fed to the SBR was kept around 0.3g N(L day)(-1). The nitrite (limiting substrate) removal percentage was 98% during most of the operational period. The specific Anammox activity of the biomass was practically constant and around 0.4 g N(g VSSday)(-1) and the average feret diameter of the formed granules was 0.64 mm. Obtained results indicated that stirring speeds up to 180 rpm have no negative effect on the performance of the Anammox process, whereas Anammox activity decreased to 40% when a rotating speed of 250 rpm was tested and the average diameter decreased in 45%, the concentration of solids in the effluent increased to 0.2g TSSL(-1) and nitrite was accumulated in the reactor up to 60 mg NL(-1).     

Evaluation of Anammox and denitrification during anaerobic digestion of poultry manure

Two approaches based on ne w process development and biological nitrogen transformation were investigated in a bench study for removing nitrogen as N2 gas from poultry waste while stabilizing the wastes. The process, known as "Anammox", was explored in batch anaerobic culture using serum bottles. The Anammox process involves the use of nitrite as an electron acceptor in the bacterially mediated oxidation of ammonia to yield N2. Studies are described wherein nitrite was added to poultry waste and the effects on ammonium levels were monitored. About 13-22% ammonium removal was observed with the inoculation of returned activated sludge, and the total ammonium reduction was not proportional to the reduction of nitrite, thereby suggesting that Anammox was less competitive under the conditions in our studies. The addition of nitrite and nitrate was not inhibitory to the process based on gas generation and COD reduction. The classical nitrogen removal process of nitrification followed with denitrification offers a more reliable basis for nitrogen removal from poultry wastes.     

Cadmium biosorption on Spirulina platensis biomass

Dry biomass of Spirulina platensis re-hydrated for 48 h was employed as a biosorbent in tests of cadmium(II) removal from water. Various concentrations of biomass (from 1 to 4 g l⁻¹) and metal (from 100 to 800 mg l⁻¹) were tested. Low biomass levels (X_o  2 g l⁻¹) ensured metal removal up to 98% only at Cd₀= 100 and 200 mg l⁻¹, while X_o  2.0 g l⁻¹ were needed at Cd₀ = 400 mg l⁻¹ to achieve satisfactory results. Whereas X_o = 4.0 g l⁻¹ was effective to remove up to Cd₀ = 500 mg l⁻¹, a further increase in metal concentration (Cd₀ = 600 and 800 mg l⁻¹) led to progressive worsening of the system performance. At a given biomass levels, the kinetics of the process was better at low Cd²⁺ concentrations, while, raising the adsorbent level from 1.0 to 2.0 g l⁻¹ and then to 4.0 g l⁻¹, the rate constant of biosorption increased by about one order of magnitude in both cases and the adsorption capacity of the system progressively decreased from 357 to 149 mg g⁻¹.     

Nitrogen removal performance of a hybrid anammox reactor

The anaerobic ammonium oxidation (anammox) process has attracted considerable attention in recent years as an alternative to conventional nitrogen removal technologies. In this study, an innovative hybrid reactor combining fluidized and fixed beds for anammox treatment was developed. The fluidized bed was mechanically stirred and the gaseous product could be rapidly released from the anammox sludge to prevent washout of the sludge caused by floatation. The fixed bed comprising a non-woven biomass carrier could efficiently catch sludge to reduce washout. During the operation, nitrogen loading rates to the reactor were increased to 27.3 kg N/m³/d, with total nitrogen removal efficiencies of 75%. The biomass concentration in the fluidized bed reached 26-g VSS/L. Anammox granules were observed in the reactors, with settling velocities and sludge volumetric index of 27.3 ± 6.5 m/h and 23 mL/g, respectively. Quantification of extracellular polymeric substances revealed the anammox granules contained a significant amount of extracellular proteins.     

Enhanced biological phosphate removal by granular sludge in a sequencing batch reactor

A laboratory-scale sequencing batch reactor was started-up with flocculated biomass and operated primarily for enhanced biological phosphate removal. Ten weeks after the start-up, gradual formation of granular sludge was observed. The compact biomass structure allowed halving the settling time, the initial reactor volume, and doubling the influent COD concentration. Continued operation confirmed the possibility of maintaining a stable granular biomass with a sludge volume index less than 40 ml g^–1, while securing a removal efficiency of 95% for carbon, 99.6% for phosphate, and 71% for nitrogen. Microscopic observations revealed a morphological diversity.