Enhancement of the activated sludge process by activated carbon produced from surplus biological sludge

Surplus biological sludge from wastewater treatment operations was converted into activated carbon and then added to the aerated vessel of an activated sludge process treating phenol and glucose. The addition of activated carbon, either sludge-based or commercial, enhanced phenol removal from 58 to 98.7% and from 87 to 93% for COD with feed concentrations of 100 mg phenol l^–1 and 2500 mg COD l^–1. No differences were found between the activated sludge-activated carbon bench scale continuous reactors operating with either commercial or sludge-based activated carbon in spite of the higher adsorption capacity of the former.     

Adsorption of Cr(VI) on activated rice husk carbon and activated alumina

The possible use of activated rice husk and activated alumina as the adsorbents of Cr(VI) from synthetic solutions and the effect of operating parameters were investigated. The activated rice husk carbon was prepared thermally in two sizes 0.3 and 1.0 mm. The maximum removal of Cr(VI) occurred at pH 2 by activated rice husk and at pH 4 by activated alumina. The amounts of Cr(VI) adsorbed increased with increase in dose of both adsorbents and their contact time. The Freundlich isotherm was applied.     

Performances of toluene removal by activated carbon derived from durian shell

In the effort to find alternative low cost adsorbent for volatile organic vapors has prompted this research in assessing the effectiveness of activated carbon produced from durian shell in removing toluene vapors. Durian shells were impregnated with different concentrations of H₃PO₄ followed by carbonization at 500 °C for 20 min under nitrogen atmosphere. The prepared durian shell activated carbon (DSAC) was characterized for its physical and chemical properties. The removal efficiency of toluene by DSAC was performed using different toluene concentrations. Results showed that the highest BET surface area of the produced DSAC was 1404 m²/g. Highest removal efficiency of toluene vapors was achieved by using DSAC impregnated with 30% of acid concentration heated at 500 °C for 20 min heating duration. However, there is insignificant difference between removal efficiency of toluene by DSAC and different toluene concentrations. The toluene adsorption by DSAC was better fitted into Freundlich model.     

Preparation and characterization of activated carbon produced from rice straw by (NH4)2HPO4 activation

Effects of different pretreatment protocols in (NH(4))(2)HPO(4) activation of rice straw on porous activated carbon evolution were evaluated. The pore structure, morphology and surface chemistry of obtained activated carbons were investigated by nitrogen adsorption, scanning electron microscopy and Fourier transform infrared spectroscopy. It was found that pretreatment combining impregnation with (NH(4))(2)HPO(4) and preoxidation could significantly affect the physicochemical properties of prepared activated carbons. The apparent surface area and total pore volume as high as 1154 m(2)/g and 0.670 cm(3)/g were obtained respectively, when combined process of impregnation followed by preoxidation at 200°C and activation at 700°C was carried out. Meanwhile, the activated carbon yield and maximum methylene blue adsorption capacity up to 41.14% and 129.5 mg/g were achieved, respectively. The results exhibited that (NH(4))(2)HPO(4) could be an effective activating agent for producing activated carbons from rice straw.     

Utilization of rice husks as a feedstock for preparation of activated carbon by microwave induced KOH and K2CO3 activation

Rice husk (RH), an abundant by-product of rice milling, was used for the preparation of activated carbon (RHAC) via KOH and K(2)CO(3) chemical activation. The activation process was performed at the microwave input power of 600 W for 7 min. RHACs were characterized by low temperature nitrogen adsorption/desorption, scanning electron microscopy and Fourier transform infrared spectroscopy. The adsorption behavior was examined using methylene blue as adsorbate. The K(2)CO(3)-activated sample showed higher yield and better pore structures and adsorption capacity development than the KOH-activated sample, with a BET surface area, total pore volume and monolayer adsorption capacity of 1165 m(2)/g, 0.78 cm(3)/g and 441.52 mg/g, respectively. The results revealed the feasibility of microwave heating for preparation of high surface area activated carbons from rice husks via K(2)CO(3) activation.     

Preparation and characterization of activated carbon from rice bran

A study on the preparation of rice bran-based activated carbon was conducted, with and without an acid treatment step prior the activation process. The influence of the activation time on the structure of the activated carbons was evaluated. The acid treatment had a significant positive influence on sorption properties. The rice bran-activated carbon presented a BET surface area of 652m(2)g(-1) and a pore volume of 0.137cm(3)g(-1), with mesopores predominance (ca. 55%). These experimental results indicated the potential use of rice bran as a precursor in the activated carbon preparation process, thus representing an economically promising material.     

Adsorption of heavy metal ions from aqueous solutions by activated carbon prepared from apricot stone

Apricot stones were carbonised and activated after treatment with sulphuric acid (1:1) at 200 degrees C for 24 h. The ability of the activated carbon to remove Ni(II), Co(II), Cd(II), Cu(II), Pb(II), Cr(III) and Cr(VI) ions from aqueous solutions by adsorption was investigated. Batch adsorption experiments were conducted to observe the effect of pH (1-6) on the activated carbon. The adsorptions of these metals were found to be dependent on solution pH. Highest adsorption occurred at 1-2 for Cr(VI) and 3-6 for the rest of the metal ions, respectively. Adsorption capacities for the metal ions were obtained in the descending order of Cr(VI) > Cd(II) > Co(II) > Cr(III) > Ni(II) > Cu(II) > Pb(II) for the activated carbon prepared from apricot stone (ASAC).     

Adsorption of gold ions from industrial wastewater using activated carbon derived from hard shell of apricot stones - an agricultural waste

In this study, hard shell of apricot stones was selected from agricultural solid wastes to prepare effective and low cost adsorbent for the gold separation from gold-plating wastewater. Different adsorption parameters like adsorbent dose, particle size of activated carbon, pH and agitation speed of mixing on the gold adsorption were studied. The results showed that under the optimum operating conditions, more than 98% of gold was adsorbed onto activated carbon after only 3 h. The equilibrium adsorption data were well described by the Freundlich and Langmuir isotherms. Isotherms have been used to obtain thermodynamic parameters. Gold desorption studies were performed with aqueous solution mixture of sodium hydroxide and organic solvents at ambient temperatures. Quantitative recovery of gold ions is possible by this method. As hard shell of apricot stones is a discarded as waste from agricultural and food industries, the prepared activated carbon is expected to be an economical product for gold ion recovery from wastewater.     

Adsorption of Bovine Serum Albumin from salt solution onto activated carbon

One of the wastewaters from tanning industry (soak liquor) contains 0.4 g/l of dissolved protein. During coagulation and flocculation 41 % of protein was removed. A suggestion has been made to remove the residual protein by adsorption technique. The optimum conditions for adsorption of Bovine Serum Albumin (BSA) on rice bran based activated carbon (RBAC) have been determined. Maximum adsorption of BSA took place at pH 7.O. Ionic strength was found to have influence on the adsorption behaviour. Adsorption capacity of BSA onto charcoal surface decreased with increase in temperature. Enthalpy of adsorption in all cases was found to be within –19 to –57 kJ/mole, indicating exothermic nature of the process. Applicability of adsorption technique to the removal of dissolved protein from soak water has been studied. The maximum removal of protein occurred at pH 7.0 and the ratio of protein removed to weight of adsorbent was 3.22×10^–3 g/g.     

Reduction of malachite green to leucomalachite green by intestinal bacteria.

Intestinal microfloras from human, rat, mouse, and monkey fecal samples and 14 pure cultures of anaerobic bacteria representative of those found in the human gastrointestinal tract metabolized the triphenylmethane dye malachite green to leucomalachite green. The reduction of malachite green to the leuco derivative suggests that intestinal microflora could play an important role in the metabolic activation of the triphenylmethane dye to a potential carcinogen.     

Biodegradation of malachite green by Ochrobactrum sp.

This study presents the biodegradation of malachite green (MG), a triphenylmethane dye, using a novel microorganism isolated from textile effluent contaminated environment. The organism responsible for degradation was identified as Ochrobactrum sp JN214485 by 16S rRNA analysis. The effect of operating parameters such as temperature, pH, immobilized bead loading, and initial dye concentration on % degradation was studied, and their optimal values were found to be 30 °C, 6, 20 g/L and 100 mg/L, respectively. The analysis showed that the extracellular enzymes were responsible for the degradation. The biodegradation of MG was confirmed by UV–visible spectroscopic and FTIR analysis. The phytotoxicity test concluded that the degradation products were less toxic compared to MG. The kinetics of biodegradation was studied and the activation energy was found to be 10.65 kcal/mol.     

Study on activated carbon derived from sewage sludge for adsorption of gaseous formaldehyde

The aim of this work is to evaluate the adsorption performances of activated carbon derived from sewage sludge (ACSS) for gaseous formaldehyde removal compared with three commercial activated carbons (CACs) using self-designing adsorption and distillation system. Formaldehyde desorption of the activated carbons for regeneration was also studied using thermogravimetric (TG) analysis. The porous structure and surface characteristics were studied using N₂ adsorption and desorption isotherms, scanning electron microscopy (SEM) and Fourier transform infrared spectroscopy (FTIR). The results show that ACSS has excellent adsorption performance, which is overall superior to the CACs. Adsorption theory indicates that the ACSS outperforms the CACs due to its appropriate porous structure and surface chemistry characteristics for formaldehyde adsorption. The TG analysis of desorption shows that the optimum temperature to regenerate ACSS is 75 °C, which is affordable and economical for recycling.     

Comparison on pore development of activated carbon produced from palm shell and coconut shell

A series of experiments were conducted to compare the pore development in palm-shell and coconut-shell-based activated carbons produced under identical experimental conditions. Carbonization and activation processes were carried out at 850 degrees C using a fluidized bed reactor. Within the range of burn-off studied, at any burn-off, the micropore and mesopore volumes created in palm-shell-based activated carbon were always higher than those of coconut-shell-based activated carbon. On macropore volume, for palm-shell-based activated carbon, the volume increased with increase in burn-off up to 30% and then decreased. However, for coconut-shell-based activated carbon, the change in macropore volume with burn-off was almost negligible but the absolute macropore volume decreased with burn-off.     

Biotransformation of malachite green by the fungus Cunninghamella elegans

The filamentous fungus Cunninghamella elegans ATCC 36112 metabolized the triphenylmethane dye malachite green with a first-order rate constant of 0.029 micromol x h(-1) (mg of cells)(-1). Malachite green was enzymatically reduced to leucomalachite green and also converted to N-demethylated and N-oxidized metabolites, including primary and secondary arylamines. Inhibition studies suggested that the cytochrome P450 system mediated both the reduction and the N-demethylation reactions.     

Adsorption of chromium from aqueous solution by activated alumina and activated charcoal

Cr(VI) is considered to be potentially carcinogenic to humans. Removal of Cr(VI) ions from aqueous solution under different conditions was investigated using activated alumina (AA) and activated charcoal (AC) as adsorbents. Batch mode experiments were conducted to study the effects of adsorbent dose, contact time, pH, temperature and initial concentration of Cr(VI). Results showed that the adsorption of Cr(VI) depended significantly on pH and temperature. Equilibrium studies showed that Cr(VI) had a high affinity for AA at pH 4 and AC at pH 2. For AA, maximum adsorption was found at 25 degrees C, indicating exothermic adsorption, while for AC, maximum adsorption was at 40 degrees C. Freundlich and Langmuir adsorption isotherms were also applied and they showed good fits to the experimental data. The results suggest that both AA and AC could be used as effective adsorbents for the removal of Cr(VI) ions.     

Separation of phthalate esters from bio-oil derived from rice husk by a basification-acidification process and column chromatography

Solid precipitate containing phthalate esters was obtained from rice-husk-derived oil through a basification-acidification process. After separation by column chromatography, the solid precipitate was divided into two mono-component fractions, two bi-component fractions and a tetra-component fraction. The major compounds of the five fractions were all consisted of phthalate esters. Especially, phthalate esters accounted for a proportion higher than 80% in both Fractions I and II. The generation and precipitation mechanisms of phthalate esters were proposed. Phthalate esters were considered to be derived from a series of complicated chemical reactions of small molecules in the biomass pyrolysis process, and precipitated from bio-oil by catalytic hydrolysis and esterification.     

裂褶菌cfcc7252菌株对孔雀石绿染料的高效降解

【目的】评价裂褶菌cfcc7252菌株降解孔雀石绿(Malachite Green,MG)的能力及其潜在的应用价值。【方法】采用单因子液体培养实验,研究了通气、p H、温度、碳源和氮源种类及浓度、金属离子、盐度、染料浓度对该菌降解效果的影响;采用平皿培养实验,利用植物种子萌发和微生物抑菌实验对降解产物进行毒性测试。【结果】研究结果表明,裂褶菌cfcc7252菌株在好氧和厌氧条件下均能高效降解MG。该菌在10.0 g/L葡萄糖,5.0 g/L酵母浸粉,0.01 mmol/L Zn2+,p H为4.0的液体培养基中培养36 h,对350 mg/L的MG降解率达67.8%;连续降解7次后,其降解率还能保持在95.4%以上。此外,该菌在盐度低于10.20%时,其对MG的降解率均达到98%以上。对植物、微生物的毒性测试结果表明,MG降解产物对红豆、豌豆等植物、金黄色葡萄球菌、枯草芽孢杆菌和铜绿假单胞杆菌等微生物基本没有毒性。【结论】裂褶菌cfcc7252菌株在处理以MG为主的染料废水时具有很强的应用潜力。     

Stimulation of mycelia growth in several mushroom species by rice husks

When supplemented to the culture medium of mushroom Coprinus cinereus, rice husks soaked beforehand in methanol stimulated mycelia growth up to a concentration of 80 mg/ml dose-dependently, whereas the non-treated stimulated mycelia growth up to 20 mg/ml. This result suggests the existence of both stimulatory and inhibitory substances in rice husks. Since momilactone A (MLA) is recognized as one of the phytoalexins in rice husks, its biological activity against mycelia growth was tested. Momilactone A inhibited mycelia growth at 5 microg/disc, whereas the methanol extract of husks did so at 1 mg/disc, wherein 0.2 microg of MLA was estimated by LC/MS/MS. Thus the phytoalexins including MLA should inhibit mycelia growth. Rice husks stimulated mycelia growth in some edible mushroom species such as Grifola frondosa (maitake), Lentinus edodes (shiitake), Pleurotus eryngii (eringi), and P. ostreatus (hiratake). Our findings might lead to the development of new profitable cultivation methods for mushrooms using rice husks.     

Adsorption kinetics of a basic dye from aqueous solutions onto apricot stone activated carbon

The preparation of activated carbon from apricot stone with H₂SO₄ activation and its ability to remove a basic dye, astrazon yellow 7GL, from aqueous solutions were reported in this study. The adsorbent was characterized by FTIR, BET and SEM, respectively. The effects of various experimental parameters, such as initial dye concentration, pH, adsorbent dosage and temperature were investigated in a batch-adsorption technique. The optimum conditions for removal of the basic dye were found to be pH 10, 6 g/l of adsorbent dosage and equilibrium time of 35 min, respectively. A comparison of three kinetic models, the pseudo first-order, second-order and diffusion controlled kinetic models, on the basic dye-adsorbent system showed that the removal rate was heavily dependent on diffusion controlled kinetic models. The adsorption isotherm data were fitted well to Langmuir and Freundlich isotherms. The adsorption capacity was calculated as 221.23 mg/g at 50 °C. Thermodynamics parameters were also evaluated. The values of enthalpy and entropy were 49.87 kJ/mol and 31.93 J/mol K, respectively, indicating that this process was spontaneous and endothermic. The experimental studies were indicated that ASC had the potential to act as an alternative adsorbent to remove the basic dye from aqueous solutions.