Preparation and characterization of polyaniline/chitosan blend film

Films consisting of a blend of a chitosan hydrogel and a conductive polymer, polyaniline (PANI), were prepared and characterized for their electrical and mechanical properties. Polyaniline in emeraldine base (EB) form was dispersed in chitosan solution and blend films were obtained by solution casting. The PANI particles in the blend films were then doped with HCl where we observed reductions in the film tensile strength and Young's modulus by about 30%, but the films electrical conductivity increased by 6 orders of magnitude. The highest electrical conductivity of the blend films was of the order 10⁻⁴ S/cm. The electrical and mechanical properties of the films varied with polyaniline content, acid dopant type, acid dopant concentration, and doping time.     

Aluminum inhibits the growth of hydroxyapatite crystals developed on a biomimetic methacrylic polymer

ProjectAluminum (Al) is an increasing problem in biomedicine since it can interact with phosphates. Bone is one of the preferential target tissues of Al deposition: Al interacts with mineralization and/or bone cell activities. We searched the influence of Al deposition in hydroxyapatite developed on a biomimetic polymer (carboxymethylated poly(2-hydroxyethyl-methacrylate)) which mimics bone mineralization in the absence of cells.ProceduresPellets of polymer were incubated for 5 days in a synthetic body fluid (SBF) to induce mineralization, then 21 days in SBF containing 20, 40 and 60 μg/L Al³⁺. Other pellets were incubated in SBF containing commercial Al foil (33 mg/vial) either in 1, 2 or 6 pieces. The mineral deposits were dissolved in HCl and Ca²⁺, PO₄^3? and Al³⁺ content was measured. Hydroxyapatite was characterized by SEM and X energy-dispersive X-ray analysis (EDX).ResultsThe amount of Al³⁺ was dose-dependently increased in Ca/P deposits on the polymer pellets. At high concentration (or with the 6 Al foils) growth of hydroxyapatite calcospherite was inhibited; only calcified plates emerging from the polymer were observed. Pellets incubated with 1 and 2 Al foils exhibited a reduction in calcospherite diameter and an increase in the Al³⁺/Ca²⁺ ratio. EDX identified Al in the mineral deposits.ConclusionsIn this acellular model, Al³⁺ altered the growth of calcospherites at low concentration and inhibited their development at high concentration. In SBF, a release of Al³⁺ from aluminum foils also inhibited mineralization. This study emphasizes the importance of Al in bone pathology and stresses the question of its release from biomaterials.     

Entrapment of 5‐aminolevulinic acid under edible composite film of konjac glucomannan and chitosan

5‐Aminolevulinic acid (5‐ALA) is a known plant regulator and growth promoter. It is a very sensitive and highly unstable compound that is easy to deteriorate. Here we propose a novel approach to stabilize 5‐ALA into a film. Films from konjac glucomannan (KGM), KGM treated with alkali solution (KGOH), chitosan (CHI) as well as blends between KGOH and CHI were fabricated for 5‐ALA entrapment. It was found that the efficiency of KGM film, KGOH film and CHI film for 5‐ALA entrapment was 55.7 ± 0.73%, 58.3 ± 0.36% and 60.3 ± 0.18 %, respectively. A 25:75 (%w/w) blended film (KGOH/CHI) showed the highest entrapment efficiency of 5‐ALA (65.9 ± 0.37%) versus other films. The possible mechanism for entrapment of 5‐ALA in blended film was postulated under two mechanisms. A secondary amide that leads to the interaction between the amino group of CHI and carboxyl group of 5‐ALA is proposed as the first mechanism. The fact that the 5‐ALA molecule was entrapped within the complexity of KGOH structure is proposed as the second mechanism. Therefore, stabilizing 5‐ALA in a film may be an alternative way to use and preserve 5‐ALA for further applications.     

Preparation of single or double-network chitosan/poly(vinyl alcohol) gel films through selectively cross-linking method

A selectively cross-linking method, which is based on the “di–diol” interaction between poly(vinyl alcohol) and borate and the strong electrostatic interaction between chitosan and tripolyphosphate, was developed. Chitosan/poly(vinyl alcohol) films cross-linked separately with borate, tripolyphosphate and borate/tripolyphosphate were then prepared in terms of this method. Water vapor permeation, mechanical strength, surface morphology and molecular interactions of the films were studied by water permeation test, texture test, atomic force microscopy and ATR-FTIR spectroscopy. With the introduction of cross-linking structure, there is a large improvement in elastic modulus from 271 ± 14.2 to 551 ± 14.7 MPa and a large decrease in water vapor permeability from (5.41 ± 0.21) × 10⁻⁷ g/m h Pa to (3.12 ± 0.24) × 10⁻⁷ g/m h Pa of chitosan/poly(vinyl alcohol) films. The surface morphology of the cross-linked films exhibits a nanoparticle aggregation structure. The size and aggregation behavior of these nanoparticles are strongly related to the type of cross-linker. Furthermore, ATR-FTIR results indicate that strong interaction between polymer matrix and cross-linker exists in our system. This work provides a simple and efficient way to prepare chitosan/poly(vinyl alcohol) films with controllable network structure.     

Properties and microstructure of protein-based film from round scad (Decapterus maruadsi) muscle as affected by palm oil and chitosan incorporation

The properties of protein-based film prepared from round scad (Decapterus maruadsi) muscle in the absence and the presence of palm oil and/or chitosan were investigated. Films added with 25% palm oil (as glycerol substitiution) had the slight decrease in water vapor permeability (WVP) and elongation at break (EAB) (p < 0.05). WVP and tensile strength (TS) of films increased but EAB decreased when 10–40% chitosan (as protein substitution) was incorporated (p < 0.05). Hydrophobic interactions and hydrogen bonds, together with disulfide and non-disulfide covalent bonds, played an important role in stabilizing the film matrix. The a* and b*-values increased with increasing chitosan levels (p < 0.05). Films added with chitosan were less transparent and had the lowered transmission in the visible range. The incorporation of 25% palm oil and 40% chitosan yielded the films with the improved TS but decreased water vapor barrier property. Apart from film strengthening effect, chitosan inconjunction with Tween-20 most likely functioned as the emulsifier/stabilizer in film forming solution containing palm oil.     

Synthesis of multifunctional chitosan with galactose as a targeting ligand for glycoprotein receptor

Chitosan-O-PEG-galactose was synthesized through hydroxyl groups of chitosan, which followed several steps including protection of amino group of chitosan, pegylation of chitosan, galactosylation of pegylated chitosan, and final removal of protection to obtain chitosan-O-PEG-galactose. The synthesized intermediates and final product were characterized and confirmed by ¹H NMR and FTIR, and the amounts of PEG and galactose conjugated with chitosan were measured. The pegylated chitosan possesses amphiphilic property in terms of soluble in both neutral aqueous (e.g., water) and organic solvents (e.g., DMF, dichloromethane). The corresponding critical micelle concentration is measured to be 0.56 mg/mL, and the size of micelles is 294.5 ± 2.3 nm with polydispersity 0.123 ± 0.021. The contents of PEG and galactose conjugated in chitosan-O-PEG-galactose are 98.09 ± 4.63% w/w and 3.06 ± 0.54% w/w, respectively. In terms of the degree of O-substitution of chitosan by PEG (DS_PEG) and the degree of substitution of PEG by galactose (DS_g) are 177.69% and 86.7%, respectively. Exclusively high DS_PEG indicates both C6–OH and C3–OH of chitosan are conjugated with PEG polymer chains. Further prominent attachment of galactose onto hydroxyl end group of PEG allows chitosan-O-PEG-galactose to possess sufficient quantity of targeting moieties for asialoglycoprotein receptor on hepatocytes.     

An amperometric cholesterol biosensor based on multiwalled carbon nanotubes and organically modified sol-gel/chitosan hybrid composite film

A new type of amperometric cholesterol biosensor based on sol-gel chitosan/silica and multiwalled carbon nanotubes (MWCNTs) organic-inorganic hybrid composite material was developed. The hybrid composite film was used to immobilize cholesterol oxidase on the surface of Prussian blue-modified glass carbon electrode. Effects of some experimental variables such as enzyme loading, concentration of Triton X-100, pH, temperature, and applied potential on the current response of the biosensor were investigated. Analytical characteristics and dynamic parameters of the biosensors with and without MWCNTs in the hybrid film were compared, and the results show that analytical performance of the biosensor can be improved greatly after introduction of the MWCNTs. Response time, sensitivity, linear range, limit of detection (S/N=3), and apparent Michaelis-Menten constant Km are 25s, 0.54 microA mM(-1), 8.0 x 10(-6) to 4.5 x 10(-4) M, 4.0 x 10(-6) M, and 0.41 mM for the biosensor without MWCNTs and 13 s, 1.55 microA mM(-1), 4.0 x 10(-6) to 7.0 x 10(-4) M, 1.0 x 10(-6) M, and 0.24 mM for the biosensor with MWCNTs, respectively. The activation energy of the enzyme-catalyzed reaction was measured to be 42.6 kJ mol(-1). This method has been used to determine the free cholesterol concentration in real human blood samples.     

Preparation, characterization and antimicrobial activity of a bio-composite scaffold containing chitosan/nano-hydroxyapatite/nano-silver for bone tissue engineering

In this study, a bio-composite scaffold containing chitosan/nano-hydroxyapatite/nano-silver particles (CS/nHAp/nAg) was developed by freeze drying technique, followed by introduction of silver ions in controlled amount through reduction phenomenon by functional groups of chitosan. The scaffolds were characterized using SEM, FT-IR, XRD, swelling, and biodegradation studies. The testing of the prepared scaffolds with Gram-positive and Gram-negative bacterial strains showed antibacterial activity. The scaffold materials were also found to be non-toxic to rat osteoprogenitor cells and human osteosarcoma cell line. Thus, these results suggested that CS/nHAp/nAg bio-composite scaffolds have the potential in controlling implant associated bacterial infection during reconstructive surgery of bone.     

Osteogenesis promoted by calcium phosphate N,N-dicarboxymethyl chitosan

The effects of N,N-dicarboxymethyl chitosan (DCMC) on the precipitation of insoluble calcium salts, namely phosphate, sulfate, oxalate, carbonate, bicarbonate and fluoride, and magnesium salts, namely phosphate and carbonate, were studied. Results indicated that the chelating ability of DCMC interfered effectively with the well-known physico-chemical behaviour of magnesium and calcium salts. Dicarboxymethyl chitosan formed self-sustaining gels upon mixing with calcium acetate, as a consequence of calcium chelation. DCMC mixed with calcium acetate and with disodium hydrogen phosphate in appropriate ratios (molar ratio Ca/DCMC close to 2.4) yielded a clear solution, from which, after dialysis and freeze-drying, an amorphous material was isolated containing an inorganic component about one half its weight. This compound was used for the treatment of bone lesions in experimental surgery and in dentistry. Bone tissue regeneration was promoted in sheep, leading to complete healing of otherwise non-healing surgical defects. Radiographic evidence of bone regeneration was observed in human patients undergoing apicectomies and avulsions. The DCMC–CaP chelate favoured osteogenesis while promoting bone mineralization.     

A facile method for preparing biodegradable chitosan derivatives with low grafting degree of poly(lactic acid)

Chemical modification of chitosan by grafting with PLA (CS-g-PLA) was developed via 1-ethyl-3-(3-dimethylaminopropyl) carbodiimide (EDC) mediated coupling reaction. The introduction of PLA disrupted the crystalline structure of chitosan, improved its solubility and thermal stability. Low degree of PLA substitution showed better degradation efficiency than chitosan and PLA. Weight loss of CS-g-PLA6 and CS-g-PLA4 was 87% and 94%, respectively, in 7 days enzymatic degradation study. CS-g-PLA2 was totally degraded in 1 day. Self-assembly behavior was studied using pyrene fluorescence dye technique and found to be PLA grafting level dependent. CS-g-PLA with low grafting degree showed hydrophilic, self-assembling properties and controllable biodegradability that may widen its applications.     

Rheological characterisation of a novel thermosensitive chitosan/poly(vinyl alcohol) blend hydrogel

Thermosensitive hydrogels that are triggered by changes in environmental temperature thus resulting in in situ hydrogel formation have recently attracted the attention of many investigators for biomedical applications. In the current work, the thermosensitive hydrogel was prepared through the mixture of chitosan (CS), poly(vinyl alcohol) (PVA) and sodium bicarbonate. The mixture was liquid aqueous solutions at low temperature (about 4 °C), but a gel under physiological conditions. The hydrogel was characterized by FTIR, swelling and rheological analysis. The effect of hydrogel composition and temperature on both the gel process and the gel strength was investigated from which possible hydrogel formation mechanisms were inferred. In addition, the hydrogel interior morphology as well as porosity of structure was evaluated by scanning electron microscopy (SEM). The potential of the hydrogels as vehicles for delivering bovine serum albumin (BSA) were also examined. In this study, the physically crosslinked chitosan/PVA gel was prepared under mild conditions without organic solvent, high temperature or harsh pH. The viscoelastic properties, as investigated rheologically, indicate that the gel had good mechanical strength. The gel formed implants in situ in response to temperature change, from low temperature (about 4 °C) to body temperature, which was very suitable for local and sustained delivery of proteins, cell encapsulation and tissue engineering.     

Improved blood biocompatibility of composite film of chitosan/carbon nanotubes complex

Single-walled carbon nanotubes are novel molecular-scale wires having excellent anti-adhesion properties with regard to platelets. On the other hand, chitosan is a partially de-acetylated derivative of chitin that has a critical role in cell attachment and growth. The aim of this study was to investigate how carbon nanotubes improve the blood biocompatibility of chitosan film. We prepared composite films with various concentrations of chitosan/carbon nanotubes (CS/CNTs) (1.3–6.3 wt%). The sample surfaces were characterized by Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM), and contact angle measurements. The surface characterization revealed that the surface of the CS/CNTs composite film became more hydrophobic with increasing amounts of CNTs. Cell attachment tests using bovine aortic endothelial cells (BAECs) indicated that CS/CNTs composite films retained their cell adhesion ability. The blood compatibility of the CS/CNTs composite films was evaluated using the blood platelet adhesion and activation tests in vitro. Platelet adhesion results confirmed that platelet adhesion and the formation of a platelet network were inhibited on composite films with higher concentrations of CNTs (5.1 wt%). Our experimental results show that the novel composite film containing CS/CNTs possesses two paradoxical characteristics, namely, good adherence of endothelial cells and minimum adherence and activation of platelets, making this film a promising antithrombogenic material for use in the biomedical field.     

细菌视紫红质光学图像存储的灰阶特性研究

细菌视紫红质（Bacteriorhodopsin,BR）是一种具有优良光致变色特性的光敏蛋白分子,具有极好的抗疲劳性和高的光转换量子效率,可用于光学图像信息的获取和存储.文章讨论了BR分子膜在受到随空间位置变化的光强调制下,BR分子膜光吸收变化量的空间分布及其与存储图像灰度分布之间的关系;建立了BR灰度图像存储特性实验系统,并对BR-D96N薄膜存储的光学图像灰阶特性进行了实验研究,实验表明BR薄膜图像存储具有出色的灰度表现能力.     

Condensed state structure and biocompatibility of the konjac glucomannan/chitosan blend films

Specialised blend films have been prepared by blending 1% w/v konjac glucomannan aqueous with 1% w/v chitosan solution in acetate solution and drying at room temperature for 24 h. The condensed state structure and miscibility of the blend films were studied by Fourier transform infrared spectroscopy, scanning electron microscopy, differential scanning calorimetry, and wide-angle X-ray diffraction. The results indicated that the blend film obtained from an 80/20 mixing ratio of konjac glucomannan and chitosan derivate showed the highest miscibility and blend homogeneity, and that strong intermolecular hydrogen bonds took place between the amino groups of chitosan and the hydroxyl groups of konjac glucomannan; thus the tensile strength also achieved its maximum in this ratio. The cell morphologies on the pure and blend films were examined by light microscopy and cell viability was studied by using MTT assay. The results showed that the particular blend film was more suitable for the cell culture than the pure konjac glucomannan film, and that the cells cultured on this blend film had greater spreading coefficients than that of the pure konjac glucomannan film. As a result of the good mechanical properties, miscibility and biocompatibility, the blend film is a promising biomaterial matrix.     

Enzymatic production and biological activities of chitosan oligosaccharides (COS): A review

Many researchers have focused chitosan as a source of potential bioactive material during past few decades. However, chitosan has several drawbacks to be utilized in biological applications, including poor solubility under physiological conditions. Therefore, a new interest has recently been emerged on partially hydrolyzed chitosan, chitosan oligosaccharides (COS). During the resent past, several technological approaches have been taken to prepare COS and, enzymatic preparation methods captured a great interest due to safe and non-toxic concerns. With time, new improvements were introduced to enzymatic production and presently it has been developed to a continuous production process. Many of the biological activities reported for COS, such as antimicrobial, anticancer, antioxidant, and immunostimulant effects are depend on their physico-chemical properties. In this review, we have summarized different enzymatic preparation methods of COS and some of their reported biological activities.     

Electrospinning of poly(vinyl alcohol)-water-soluble quaternized chitosan derivative blend

Defect free mats containing a cationic polysaccharide, chitosan derivative such as N-[(2-hydroxy-3-trimethylammonium)propyl] chitosan chloride (HTCC), have been prepared using electrospinning of an aqueous solution of poly(vinyl alcohol) (PVA)-HTCC blends. HTCC, a water-soluble derivative of chitosan, was synthesized via the reaction between glycidyl-trimethylammonium chloride and chitosan. Solutions of PVA-HTCC Blends were electrospun. The morphology, diameter and structure of the produced electrospun nanofibres were examined by scanning electron microscopy (SEM). The average fibre diameter was in the range of 200-600 nm. SEM images showed that the morphology and diameter of the nanofibres were mainly affected by weight ratio of the blend and applied voltage. The results revealed that increasing HTCC content in the blends decreases the average fibre diameter. These observations were discussed on the basis of shear viscosities and conductivities of the spinning solutions. Microbiological assessment showed that the PVA-HTCC mats have a good antibacterial activity against Gram-positive bacteria, Staphylococcus aureus, and Gram-negative bacteria, Escherichia coli.     

Integration of chitosan and plant growth-promoting rhizobacteria to control Papaya ringspot virus and Tomato chlorotic spot virus

Papaya ringspot virus-W (PRSV-W) and Tomato chlorotic spot virus (TCSV) are common viruses infecting vegetables in south Florida. Application of plant growth-promoting rhizobacteria (PGPR) has emerged as a potential alternative of chemical pesticides to control these viruses. But, it is not sufficient to completely replace chemical control. This study aimed to investigate the synergistic effect of chitosan and PGPR to control PRSV-W and TCSV. The efficiency of PGPR to suppress PRSV-W and TCSV was significantly improved when they were accompanied with chitosan treatment. The highest reduction in disease severity of both PRSV-W and TCSV was achieved when chitosan treatment was accompanied with mixture of two PGPR (IN937a + SE34) or three PGPR strains (IN937a + SE34 + SE56). The results of this study proved that implementation of chitosan and PGPR could significantly restrict losses due to PRSV-W and TCSV in squash and tomato, in Florida and the United States.     

A novel tripolymer coating demonstrating the synergistic effect of chitosan, collagen type 1 and hyaluronic acid on osteogenic differentiation of human bone marrow derived mesenchymal stem cells

The biomimetic approach mimicking in vivo micro environment is the key for developing functional tissue engineered constructs. In this study, we used a tripolymer combination consisting of a natural polymer, chitosan and two extracellular matrix components; collagen type 1 and hyaluronic acid to coat tissue culture plate to evaluate their effect on osteogenic differentiation of human bone marrow derived mesenchymal stem cells (hMSCs). The polymers were blended at different mixing ratios and the tissue culture plates were coated either by polyblend method or by surface modification method. hMSCs isolated from adult bone marrow were directed to osteoblast differentiation on the coated plates. Our results showed that the tripolymer coating of the tissue culture plate enhanced mineralization as evidenced by calcium quantification exhibiting significantly higher amount of calcium compared to the untreated or individual polymer coated plates. We found that the tripolymer coated plates having a 1:1 mixing ratio of chitosan and collagen type 1, surface modified with hyaluronic acid is an ideal combination to achieve the synergistic effect of these polymers on in vitro osteogenic differentiation of hMSCs. These results thus, establish a novel biomimetic approach of surface modification to enhance osteoblast differentiation and mineralization. Our findings hold great promise in implementing a biomimetic surface coating to improve osteoconductivity of implants and scaffolds for various orthopaedic and bone tissue engineering applications.     

Poly(3-hydroxybutyrate)/chitosan/ketoprofen or piroxicam composite microparticles: Preparation and controlled drug release evaluation

Poly(3-hydroxybutyrate)/chitosan/piroxicam or ketoprofen composite microparticles were prepared by the solid-in-water-in-oil emulsion-solvent evaporation technique with the aim of reducing the burst effect and controlling the drug release. Reservoir-type microparticles, composed of poly(3-hydroxybutyrate) microspheres embedded in a chitosan matrix were prepared. The size and morphological characteristics of the composite microparticles were evaluated in relation to the chitosan concentration and cross-linking with glutaraldehyde. Reservoir-type composite microparticles were obtained using 2.0% and 3.0% w/v chitosan solutions. A significant reduction in the burst effect and prolonged drug release were observed, particularly when higher chitosan and glutaraldehyde concentrations were used.