酸性条件下耐酸产甲烷颗粒污泥的培养及特性*

分别采用中性颗粒污泥和河底沉积物接种运行两个颗粒污泥膨胀床(EGSB)反应器,通过逐级降低pH的运行策略,驯化和培养了耐酸产甲烷颗粒污泥,两个EGSB反应器均能在pH5．8-6．2条件下稳定运行,容积负荷可达5．5-7．5kg COD,(m^3／d),COD去除率约90％;两种颗粒污泥在低pH值下均能保持较高的产甲烷活性,pH5．5时,仍能保持pH7．0时活性的51．8％和55．6％;还对耐酸颗粒污泥的粒径分布、沉降性能、金属元素含量、微观结构及细菌在颗粒表面和内部的分布等进行了研究。     

氯苯对EGSB反应器内颗粒污泥性质影响的研究*

采用EGSB反应器处理含氯苯有机废水 ,主要研究了氯苯对颗粒污泥性质的影响。结果表明 :氯苯对处理葡萄糖自配水的EGSB反应器内颗粒污泥中的细菌有较强毒害作用 ,连续投加低浓度氯苯 72d后 ,扫描电镜观察可发现颗粒污泥表面和内部细菌均明显受到损害 ,停止投加氯苯恢复运行 30d和 5 0d后 ,仍可观察到颗粒污泥内部细菌受损害的现象 ,且部分颗粒污泥内部存在着明显的空洞 ;随着运行时间的延长 ,反应器内颗粒污泥的粒径有较大程度的增大 ;但长期接触氯苯导致部分颗粒污泥解体 ,使得小粒径污泥增多 ,而大粒径     

厌氧反应器中颗粒污泥的培育及应用研究进展*

厌氧生物处理技术因其具有有机负荷高、污泥产量低、能耗低等优点被广泛应用于各种废水处理中。厌氧颗粒污泥具有沉降性能好、微生物浓度高、有机负荷高等优点,极大地提高了废水处理效率。尤其在处理含高氨氮废水中,厌氧颗粒污泥的形成对反应器的高效生物脱氮至关重要。但到目前为止,厌氧反应器中的颗粒污泥形成及废水处理效果还缺乏系统的认识。鉴于此,总结了厌氧反应器中颗粒污泥的形成机制,分析了影响厌氧反应器中颗粒污泥形成的因素,论述了厌氧反应器中厌氧颗粒污泥生长的模拟,最后介绍了厌氧颗粒污泥在国内外的主流应用。厌氧反应器中颗粒污泥的形成是综合因素影响的结果,对影响厌氧颗粒污泥形成的每个因素都需要认真对待,可为在厌氧反应器中颗粒污泥的培育和应用提供理论指导和技术支撑。     

氯苯对EGSB反应器内颗粒污泥性质影响的研究

采用ECSB反应器处理含氯苯有机废水,主要研究了氮苯对颗粒污泥性质的影响。结果表明：氮苯对处理葡萄糖自配水的EGSB反应器内颗粒污泥中的细菌有较强毒害作用,连续投加低浓度氮苯72d后,扫描电镜观察可发现颗粒污泥表面和内部细菌均明显受到损害,停止投加氮苯恢复运行30d和50d后,仍可观察到颗粒污泥内部细菌受损害的现象,且部分颗粒污泥内部存在着明显的空洞;随着运行时间的延长,反应器内颗粒污泥的粒径有较大程度的增大;但长期接触氯苯导致部分颗粒污泥解体,使得小粒径污泥增多,而大粒径污泥相应减少;氮苯对颗粒污泥的损害还表现在使大粒径颗粒的沉速减小,甚至导致部分颗粒污泥内部形成空洞而上浮。     

UASB反应器中影响污泥颗粒化的工程因素

研究了具有不同微生物群系的接种污泥、流动方式和流速对上流式厌氧污泥床(UASB)反应器中活性污泥粒化的影响。颗粒化过程包括：微生物絮凝体的形成、亚核的形成,亚核增长和颗粒成熟四个阶段。微絮凝体的形成取决于酸化菌的作用。流体的动量传递和流体对悬浮物的剪切作用是影响亚核形成的关键性工程因素。为此提出最低流速概念,即形成污泥膨胀床的最低流速。合适的进料速率、污泥负荷、布水均匀性以及碱度控制是UASB反应器工程放大和过程控制的四大要素。     

情性载体厌氧颗粒污泥培育及某些性质的研究

研究了在焦碳颗粒上起动和育成厌氧颗粒污泥(或称厌氧附着膜),及其在分批反应器和膨化床反应器内的某些运转特性。在一定的选择压力(Selection pressure)下,从悬浮态种子污泥成长为颗粒污泥的过程中,其微生物相发生了明显变化。颗粒污泥的比反应速率常数K比出发悬浮态种子污泥的增大了100％左右。从而断定,除菌体浓度很高外,菌体质量的改进是这类系统（如AAFEB和uAsB等)效率特别高的另一重要原因．     

厌氧氨氧化颗粒污泥聚集机制研究进展

厌氧氨氧化(anaerobic ammonium oxidation,anammox)工艺被认为是当前污水生物脱氮领域最经济的处理工艺,有利于实现污水处理厂的能源自给。厌氧氨氧化菌是该工艺的核心功能微生物。以厌氧氨氧化菌为主导微生物形成的厌氧氨氧化颗粒污泥具有沉速大、污泥持留能力强及对不利环境抵抗能力强等突出优势,是实现厌氧氨氧化工艺最有前景的污泥形态。本论文围绕厌氧氨氧化颗粒,介绍了厌氧氨氧化菌的特性、种类及代谢途径,综述了厌氧氨氧化颗粒污泥的形成假说及与厌氧氨氧化颗粒污泥聚集密切相关的胞外聚合物(extracellular polymeric substance,EPS)和群体感应研究现状,并对今后厌氧氨氧化颗粒的研究进行了展望,以期为后续厌氧氨氧化颗粒的研究及厌氧氨氧化颗粒工艺的优化提供参考。     

成熟厌氧颗粒污泥的结构及其特征*

厌氧序批式反应器〈AnaerobicSequencingBatchReactorASBR〉在处理啤酒废水过程中 ,能形成厌氧颗粒污泥。文中采用扫描电子显微镜和荧光显微镜技术对成熟厌氧颗粒污泥的结构及微生物群落等进行跟踪观察 ,结果显示 ,颗粒污泥结构复杂 ,细菌以微群落形式分布 ,其中产甲烷菌占一定比例。同时也探讨了厌氧颗粒污泥的形成机制。     

Anammox反应器启动过程中颗粒污泥性状变化特性

以厌氧颗粒污泥作为接种物,通过185 d的运行,成功启动了上流式厌氧氨氧化污泥床(Upflow anaerobic sludge blanket,UASB)反应器。反应器的进水氨氮与亚硝氮浓度分别提升至224 mg/L和255 mg/L,容积氮去除速率提升至3.76 kg/(m3·d)。采用红外光谱、扫描电镜和透射电镜等对厌氧氨氧化颗粒污泥的性状进行观察,发现颗粒污泥在启动过程中经历了污泥颗粒裂解到污泥颗粒重组的过程,且厌氧氨氧化颗粒污泥表面含有丰富的官能团,说明厌氧氨氧化颗粒污泥可能具有良好的吸附性能。采用宏基因组测序的方法对启动前后颗粒污泥的生态结构进行分析,发现原接种污泥优势菌群(变形菌门、厚壁菌门、拟杆菌门)丰度大幅减少,厌氧氨氧化菌所属的浮霉状菌门丰度则由1.59%提升到23.24%。     

厌氧颗粒污泥微生物群落结构与功能的研究进展

厌氧颗粒污泥(anaerobicgranularsludge,AnGS)是由多种功能微生物组成的自固定化聚集体，具有容积负荷高、工艺简单、剩余污泥产量低等优点，在废水处理领域中显示出巨大的技术和经济潜力，被认为是一种很有前景的低碳废水处理工艺。本文系统总结了近年来厌氧颗粒污泥微生物结构和功能的研究成果，从微生物学角度讨论了厌氧颗粒污泥形成及稳定的影响因素，并对今后厌氧颗粒污泥的研究进行了展望，以期为后续厌氧颗粒污泥技术的深入研究和实际工程应用提供参考。     

Anaerobic granulation technology for wastewater treatment

Anaerobic wastewater treatment using granular sludge reactors is a developing technology, in which granular sludge is the core component. So far, around 900 anaerobic granular sludge units have been operated worldwide. Although intensive research attention has been given to anaerobic granules in the past 20 years, the mechanisms responsible for anaerobic granulation and the strategy of how to expedite substantially the formation of granular sludge have not yet been completely clear. This paper reviews the mode of anaerobic granulation, including the mechanisms and models for anaerobic granulation, major factors influencing anaerobic granulation, characteristics of anaerobic granules, anaerobic granulation in other types of reactors, industrial application of anaerobic granulation technology and neural fuzzy model-based control strategy developed for anaerobic systems. Some approaches for future research are outlined.     

Granular sludge formation in upflow anaerobic sludge blanket (UASB) reactors

The state of the art for upflow anaerobic sludge blanket (UASB) reactors is discussed, focusing on the microbiology of immobilized anaerobic bacteria and the mechanism of granule formation. The development of granular sludge is the key factor for successful operation of the UASB reactors. Criteria for determining if granular sludge has developed in a UASB reactor is given based on the densities and diameters of the granular sludge. The shape and composition of granular sludge can vary significantly. Granules typically have a spherical form with a diameter from 0.14 to 5 mm. The inorganic mineral content varies from 10 to 90% of the dry weight of the granules, depending on the wastewater composition etc. The main components of the ash are calcium, potassium, and iron. The extracellular polymers in the granular sludge are important for the structure and maintenance of granules, while the inorganic composition seems to be of less importance. The extracellular polymer content varies between 0.6 and 20% of the volatile suspended solids and consists mainly of protein and polysaccharides. Both Methanosaeta spp. (formerly Methanothrix) and Methanosarcina spp. have been identified as important aceticlastic methanogens for the initial granulation and development of granular sludge. Immunological methods have been used to identify other methanogens in the granules. The results have showed that, besides the aceticlastic methanogens Methanosaeta spp. and Methanosarcina spp., hydrogen and formate utilizing bacteria are also present, e.g., Methanobacterium formicicum, Methanobacterium thermoautotrophicum, and Methanobrevibacter spp. Microcolonies of syntrophic bacteria are often observed in the granules, and the significant electron transfer in these microcolonies occurs through interspecies hydrogen transfer. The internal organization of the various groups of bacteria in the granules depends on the wastewater composition and the dominating metabolic pathways in the granules. Internal organization is observed in granules where such an arrangement is beneficial for an optimal degradation of the wastewater. A four-step model is given for the initial development of granular sludge. (c) 1996 John Wiley & Sons, Inc.     

The performance of a phase separated granular bed bioreactor treating brewery wastewater

This study presents the performance characteristics of a plug flow phase separated anaerobic granular bed baffled reactor (GRABBR) fed with brewery wastewater at various operating conditions. The reactor achieved chemical oxygen demand (COD) removal of 93-96% with high methane production when operated at organic loading rates (OLRs) of 2.16-13.38kg COD m(-3)d(-1). The reactor configuration and microbial environment encouraged the acidogenic dominant zone to produce intermediate products suitable for degradation in the predominantly methanogenic zone. Noticeable phase separation between acidogenesis and methanogenesis mainly occurred at high OLR, involving a greater number of compartments to contribute to wastewater treatment. The highly active nature and good settling characteristics of methanogenic granular sludge offered high biomass retention and enhanced methanogenic activities within the system. The granular structure in the acidogenic dominant zone of the GRABBR was susceptible to disintegration and flotation. Methanogenic granular sludge was a multi-layered structure with Methanosaeta-like organisms dominant in the core.     

Precipitation potential as a major factor in the formation of granular sludge in an upflow sludge-blanket reactor for denitrification of drinking water

The effects of the chemical composition of water on granular sludge formation and characteristics in a denitrifying upflow sludge-blanket (USB) reactor were studied. Denitrification of drinking water showed different biomass sludge characteristics when the reactor was fed with groundwater as opposed to surface water. USB reactors fed with groundwater produced granules with good settling characteristics, SVI (sludge volume index) values lower than 30 ml/g, and high reactor biomass concentrations (20–25 g/l), while surface-water-fed reactors exhibited lower biomass concentrations (10–15 g/l) due to poor settling characteristics (SVI values of 50–90 ml/g). Sludge granules from the reactor fed with surface water had a low mineral content of between 10% and 20% as compared to a mineral content of 25%–50% in the groundwater reactor. The larger mineral content in the groundwater-fed reactor was due to a greater precipitation potential, i.e. higher concentrations of calcium and alkalinity present in groundwater combined with the release of alkalinity and subsequent increase in pH caused by biological denitrification. Verification for this phenomenon was established by enriching surface water with calcium and alkalinity, which increased the reactor's precipitation potential from 15 mg/1 to 40 mg/1 (as CaCO₃). The granules obtained from the reactor fed with enriched surface water had a high mineral content of between 40% and 50% and very low SVI values, contributing to improved granule-settling characteristics and reactor stability.     

Organics and nitrogen removal and sludge stability in aerobic granular sludge membrane bioreactor

Novel aerobic granular sludge membrane bioreactor (GMBR) was established by combining aerobic granular sludge technology with membrane bioreactor (MBR). GMBR showed good organics removal and simultaneous nitrification and denitrification (SND) performances for synthesized wastewater. When influent total organic carbon (TOC) was 56.8-132.6 mg/L, the TOC removal of GMBR was 84.7-91.9%. When influent ammonia nitrogen was 28.1-38.4 mg/L, the ammonia nitrogen removal was 85.4-99.7%, and the total nitrogen removal was 41.7-78.4%. Moreover, batch experiments of sludge with different particle size demonstrated that: (1) flocculent sludge under aerobic condition almost have no denitrification capacity, (2) SND capacity was caused by the granular sludge, and (3) the denitrification rate and total nitrogen removal efficiency were enhanced with the increased particle size. In addition, study on the sludge morphology stability in GMBR showed that, although some granular sludge larger than 0.9 mm disaggregated at the beginning of operation, the granular sludge was able to maintain the stability of its granular morphology, and at the end of operation, the amount of granular sludge (larger than 0.18 mm) stabilized in GMBR was more than 56-62% of the total sludge concentration. The partial disaggregation of large granules is closely associated with the change of operating mode from sequencing batch reactor (SBR) system to MBR system.     

Formation of aerobic granules and their PHB production at various substrate and ammonium concentrations

Aerobic granular sludge rich in polyhydroxybutyrate (PHB) was cultivated in a sequencing batch reactor (SBR) by seeding anaerobic granular sludge. The PHB content in aerobic granules was investigated and the experimental results reveal that both influent chemical oxygen demand (COD) and ammonium concentrations had a significant effect on the morphological characteristics and the PHB production of the aerobic granular sludge. At a COD and ammonium concentration of 750 mg/L and 8.5mg/L, respectively, the PHB content of the granules reached 44%, but their poor settling ability, as evidenced by a high sludge volume index, was observed. This was attributed to the outgrowth of filamentous bacteria on the granule surface. However, an increase in the ammonium concentration resulted in an elevated sludge concentration and a decrease in the PHB content in the granules. In this case, the aerobic granular sludge with a regular and compact structure was formed. The results suggest that, through controlling the COD and ammonium concentrations in the influent, the PHB-rich aerobic granular sludge with good settling ability could be cultivated.     

A key cultivation technology for denitrifying granular sludge

Well-formed denitrifying granular sludge with a biomass concentration of 24.8 gVSS L^?1 and a specific nitrate removal rate of 0.19 gNO₃-N gVSS^?1 d^?1 was obtained in an upflow sludge blanket (USB) reactor by cultivating seeded aerobic flocculent sludge for 6–8 weeks. Regularity phenomena exist in the granulation including flotation of flocculent sludge, formation of fine granules, occurrence of channelling, and formation of mature granular sludge. The granulation is similar to crystal growth, that the non-denitrifying bacteria evolve into the carriers (fine granules), on the surface of which denitrifying bacteria proliferate and develop into mature granular sludge.There are several key parameters that must be considered when developing a good denitrifying granular sludge. First, the proper seed sludge must be chosen (VSS/SS at 0.65–0.75, SRT over 25 days) to accelerate the granulation process. Secondly, any floating sludge should be stirred, and the sludge loading rate should be within the range of 0.05–0.15 gNO₃-N gVSS^?1 d^?1 until fine granules emerge. Additionally, spontaneous gas agitation or interval air-blowing should be used to effectively eliminate channelling; Finally, the sludge loading rate should be less than 0.25 gNO₃-N gVSS^?1 d^?1 until dense, mature granular sludge appears. This study could support and promote the full-scale application of denitrifying granular sludge.     

Dispersal and control of anammox granular sludge at high substrate concentrations

This paper reports about the dispersal and control of anammox granular sludge at high substrate concentrations. The results demonstrate that anammox granular sludge would turn into flocculent sludge when the substrate concentrations exceed the inhibitory threshold concentrations, with an apparent drop in the settling velocity of anammox sludge from 73.73 to 16.49 m/h. Moreover, the sludge was washed out of the reactor and a decrease in the nitrogen removal rate from 23.82 to 16.97 kg N/(m³/day) was observed. The dominant anammox bacteria in the granular and flocculent sludge were Candidatus Kuenenia stuttgartiensis; however, the contents of heme c and extracellular polymeric substances in the flocculent sludge were much lower than in the granular sludge. Furthermore, the chemical composition of extracellular polymeric substances was different. The high nitrite concentrations more than the inhibitory threshold concentrations were regarded as the reason for the observed granular sludge dispersal and deterioration in reactor performance. The apparent dispersed granular sludge and malfunction of reactor performance could be recovered by means of washing out the residual substrate from the reactor and then re-running the reactor from low substrate concentrations.     

Aerobic granulation with brewery wastewater in a sequencing batch reactor

Aerobic granular sludge was cultivated in a sequencing batch reactor fed with brewery wastewater. After nine-week operation, stable granules with sizes of 2-7 mm were obtained. With the granulation, the SVI value decreased from 87.5 to 32 mL/g. The granular sludge had an excellent settling ability with the settling velocity over 91 m/h. Aerobic granular sludge exhibited good performance in the organics and nitrogen removal from brewery wastewater. After granulation, high and stable removal efficiencies of 88.7% COD(t), 88.9% NH(4)(+)-N were achieved at the volumetric exchange ratio of 50% and cycle duration of 6h. The average COD(t) and COD(s) of the effluent were 212 and 134 mg/L, respectively, and the average effluent ammonium concentration was less than 14.4 mg/L. Nitrogen was removed due to nitrification and simultaneous denitrification in the inner core of granules.     

Anaerobic digestion of long-chain fatty acids in UASB and expanded granular sludge bed reactors

Solutions of sodium caprate and sodium laurate were digested in upflow anaerobic sludge bed (UASB) reactors inoculated with granular sludge and in expanded granular sludge bed (EGSB) reactors. UASB reactors are unsuitable if lipids contribute 50% or more to the COD of waste water: the gas production rate required to obtain sufficient mixing and contact cannot be achieved. At lipid loading rates exceeding 2–3 kg COD m⁻³ day⁻¹, total sludge wash-out occurred. At lower loading rates the system was unreliable, due to unpredictable sludge flotation. EGSB reactors do fulfil the requirements of mixing and contact. They accommodate space loading rates up to 30 kg COD m⁻³ day⁻¹ during digestion of caprate or laurate as sole substrate, at COD removal efficiencies of 83–91%, and can be operated at hydraulic residence times of 2 h without any problems. Augmentation of granular sludge in lab-scale EGSB reactors was demonstrated. The new granules had excellent settling properties. Floating layer formation, as well as mixing characteristics in full-scale EGSB reactors require further research.