Electrochemical biosensor for catechol using agarose-guar gum entrapped tyrosinase

An electrochemical biosensor using tyrosinase was constructed for the determination of catechol. The enzyme was extracted from a plant source Amorphophallus companulatus and entrapped in agarose-guar gum composite biopolymer matrix. Catechol was determined by direct reduction of biocatalytically liberated quinone species at -0.1 V versus Ag/AgCl (3M KCl). The response was found to be linear and concentration dependent in the range of 6 x 10(-5) to 8 x 10(-4)M with a lower detection limit of 6 microM. It has reusability up to 20 cycles and a shelf life of more than 2 months when stored at 4 degrees C.     

A nucleic acid biosensor for the detection of a short sequence related to the hepatitis B virus using bis(benzimidazole)cadmium(II) dinitrate as an electrochemical indicator

A novel hybridization indicator, bis(benzimidazole)cadmium(II) dinitrate (Cd(bzim)(2)(NO(3))(2)), was utilized to develop an electrochemical DNA biosensor for the detection of a short DNA sequence related to the hepatitis B virus (HBV). The sensor relies on the immobilization and hybridization of the 21-mer single-stranded oligonucleotide from the HBV long repeat at the glassy carbon electrode (GCE). The hybridization between the probe and its complementary sequence as the target was studied by enhancement of the peak of the Cd(bzim)(2)(2+) indicator using cyclic voltammetry (CV) and differential pulse voltammetry (DPV). Numerous factors affecting the probe immobilization, target hybridization, and indicator binding reactions were optimized to maximize the sensitivity and speed of the assay time. With this approach, a sequence of the HBV could be quantified over the range from 1.49x10(-7)M to 1.06x10(-6)M, with a linear correlation of r=0.9973 and a detection limit of 8.4x10(-8)M. The Cd(bzim)(2)(2+) signal observed from the probe sequence before and after hybridization with a four-base mismatch containing sequence was lower than that observed after hybridization with a complementary sequence, showing good selectivity. These results demonstrate that the Cd(bzim)(2)(2+) indicator provides great promise for the rapid and specific measurement of the target DNA.     

Mixed-valence compound-based biosensor

A cobalt(II)hexacyanoferrate-based biosensor has been prepared simply by codeposition of an enzyme, together with the electrochemical formation of a cobalt (II)hexacyanoferrate compound electrochemically. The compound can be generated at a constant potential of -0.05 V (vs. Ag/AgCl). This compound possesses the catalytic property of reducing hydrogen peroxide to water at the operating potential of 0.0 V vs. Ag/AgCl. The mixed-valence compound-based biosensor possesses an unique interference-independent feature, which is important for biomedical application; this feature is attributed to the low overvoltage characteristic of cobalt (II)hexacyanoferrate. The electrochemical glucose biosensor responds to a series of glucose injections with linearity up to 5 mM (with correlation coefficient R = 0.9999) and the sensitivity of the linear portion is 733 nA/(cm2 x mM). The detection limit is 2 x 10(-6)M (S/N = 3). Both the potential-dependent electron transfer rate constant and the apparent Michaelis-Menten constant were studied in rotating disk experiments. The apparent Michaelis-Menten constant, Km' calculated from the slope of the "Lineweaver-Burke" type reciprocal plot is 28 mM. A fast-response characteristic is observed in the rotating disk experiment and the 95% response time is 14.5 sec. No response was observed from the addition of either 2 x 10(-4)M galactose, acetaminophen, ascorbic acid, uric acid, cysteine, tyrosine, dopamine, or 1,4-dihydroxyquinone in the absence and/or in the presence of 5 x 10(-4)M glucose.     

Fabrication of sucrose biosensor based on single mode planar optical waveguide using co-immobilized plant invertase and GOD

In present studies, the new optical sensing platform based on optical planar waveguide (OPWG) for sucrose estimation was reported. An evanescent-wave biosensor was designed by using novel agarose–guar gum (AG) biopolymer composite sol–gel with entrapped enzymes (acid invertase (INV) and glucose oxidase (GOD)). Partially purified watermelon invertase isolated from Citrullus vulgaris fruit (specific activity 832 units mg⁻¹) in combination with GOD was physically entrapped in AG sol–gel and cladded on the surface of optical planar waveguide. Na⁺–K⁺ ion-exchanged glass optical waveguides were prepared and employed for the fabrication of sucrose biosensor. By addressing the enzyme modified waveguide structure with, the optogeometric properties of adsorbed enzyme layer (12 μm) at the sensor solid–liquid interface were studied. The OPWG sensor with short response time (110 s) was characterized using the 0.2 M acetate buffer, pH 5.5. The fabricated sucrose sensor showed concentration dependent linear response in the range 1 × 10⁻¹⁰ to 1 × 10⁻⁶ M of sucrose. Lower limit of detection of this novel AG–INV–GOD cladded OPWG sensor was found to be 2.5 × 10⁻¹¹ M sucrose, which indicates that the developed biosensor has higher sensitivity towards sucrose as compared to earlier reported sensors using various transducer systems. Biochips when stored at room temperature, showed high stability for 81 days with 80% retention of original sensitivity. These sucrose sensing biochips showed good operational efficiency for 10 cycles. The proper confinement of acid invertase and glucose oxidase in hydrogel composite was confirmed by scanning electron microscopy (SEM) images. The constructed OPWG sensor is versatile, easy to fabricate and can be used for sucrose measurements with very high sensitivity.     

Thermodynamics and fluorescence studies of the interactions of cyclooctapeptides with Hg2+, Pb2+, and Cd2+

The purpose of this work is to characterize the interactions of cyclooctapeptides (CP) containing glutamyl and/or cysteinyl residues with common heavy-metal ions in order to facilitate the design of cyclopeptides as sensors for metal ions. Isothermal titration calorimetry studies show that cyclooctapeptides containing glutamyl and/or cysteinyl residues bind these Hg(2+) and Pb(2+) over Cd(2+) and other common metal ions. Differential binding isotherms, in their interactions with Hg(2+), support a two-binding site model, whereas pertinent interactions with Pb(2+) support a 2:1 stoichiometry, suggesting a CP/Pb(2+)/CP mode of complexation. The cyclooctapeptide containing both glutamyl and cysteinyl residues shows a significant binding affinity for Hg(2+) (K(a)=7.6x10(7)M(-1)), which is both enthalpically and entropically driven. The fluorescence of these cyclooctapeptides showed pronounced fluorescence quenching responses to Hg(2+) over Pd(2+) and Cd(2+). Stern-Volmer analyses of the dependence of fluorescence intensity on Hg(2+) and Pb(2+) are reported. The observed trends are useful for the design of Hg(2+) sensors based on fluorophore-tagged cyclooctapeptides.     

Novel synthetic phytochelatin-based capacitive biosensor for heavy metal ion detection

A novel capacitance biosensor based on synthetic phytochelatins for sensitive detection of heavy metals is described. Synthetic phytochelatin (Glu-Cys)(20)Gly (EC20) fused to the maltose binding domain protein was expressed in Escherichia coli and purified for construction of the biosensor. The new biosensor was able to detect Hg(2+), Cd(2+), Pb(2+), Cu(2+) and Zn(2+) ions in concentration range of 100 fM-10 mM, and the order of sensitivity was S(Zn)>S(Cu)>S(Hg)>S(Cd) congruent with S(Pb). The biological sensing element of the sensor could be regenerated using EDTA and the storage stability of the biosensor was 15 days.     

Glucose biosensor based on Au nanoparticles-conductive polyaniline nanocomposite

In this paper, we report a novel glucose biosensor based on composite of Au nanoparticles (NPs)-conductive polyaniline (PANI) nanofibers. Immobilized with glucose oxidase (GOx) and Nafion on the surface of nanocomposite, a sensitive and selective biosensor for glucose was successfully developed by electrochemical oxidation of H2O2. The glucose biosensor shows a linear calibration curve over the range from 1.0x10(-6) to 8.0x10(-4) mol/L, with a slope and detection limit (S/N=3) of 2.3 mA/M and 5.0x10(-7) M, respectively. In addition, the glucose biosensor system indicates excellent reproducibility (less than 5% R.S.D.) and good operational stability (over 2 weeks).     

Amperometric determination of choline released from rat submandibular gland acinar cells using a choline oxidase biosensor

A choline (CHO) biosensor based on the determination of H(2)O(2) generated at the electrode surface by the enzyme choline oxidase (CHOx) was developed. The biosensor consisted of CHOx retained onto a horseradish peroxidase (HRP) immobilized solid carbon paste electrode (sCPE). The HRPsCPE contained the molecule phenothiazine as redox mediator and CHOx was physically retained on the electrode surface using a dialysis membrane. Several parameters have been studied such as, mediator amount, influence of applied potential, etc. The CHO measurements were performed in 0.1 M phosphate buffer, pH 7.4. Amperometric detection of CHO was realized at an applied potential of 0.0 mV vs Ag/AgCl. The response is linear over the concentration range 5.0x10(-7)-7.0x10(-5) M, with a detection limit of 1.0x10(-7) M. This biosensor was used to detect choline released from phosphatidylcholine (PC) by phospholipase D (PLD) in isolated rat salivary gland cells stimulated by a purinergic agonist (ATP).     

Electrochemical impedance behavior of DNA biosensor based on colloidal Ag and bilayer two-dimensional sol-gel as matrices

A novel method for fabrication of DNA biosensors has been developed by means of self-assembling colloidal Ag (Ag) to a thiol-containing sol-gel network. The thiol groups of 3-mercaptopropyltrimethoxysilane (MPTS) serve as binding sites for the covalent attachment to gold electrode surface. Then the one-dimensional network of silane unites (1dMPTS) was combined together into a two-dimensional sol-gel network (2dMPTS) by dipping into aqueous NaOH. The second silane layer (B2dMPTS) was formed by immersing electrodes back into the MPTS solution overnight, and then the Ag nanoparticles were chemisorbed onto the thiol groups of the second silane layer. Finally, the mercapto oligonucleotide was self-assembled onto the surface via the Ag nanoparticles. The modified process was characterized by electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV). In addition, we utilized the impedance spectroscopy as a platform for DNA sensing assay. The factors influencing the performance of the resulting biosensor were studied in detail. The linear range of the biosensor was from 8.0 x 10(-9) to 1.0 x 10(-6) M with a detection limit of 4.0 x 10(-9) M at 3sigma. In addition, the experiment results indicate that oligonucleotide immobilized on this way exhibits a good sensitivity and selectivity, high stability and a long-term maintenance of bioactivity.     

Interaction of metal ions with caffeine and theophylline: stability and structural features

The interactions of caffeine and theophylline with divalent cadmium, mercury, strontium and barium ions were studied in aqueous solution and physiological pH. Fourier transform infrared spectroscopy (FTIR) and absorption spectra were used to determine the cation binding mode and association constants. Spectroscopic results showed that Cd(2+), Hg(2+), Sr(2+) and Ba(2+) bind strongly to caffeine and theophylline. Direct and indirect (through metal hydration shell) interactions were observed for caffeine and theophylline with Cd(2+), Hg(2+), Sr(2+) and Ba(2+) through O6 and N9 (caffeine) and O6, N9 and N7 atoms (theophylline). The overall binding constants are:k(Cd-caffeine) = 1.24 x 10(5) M(-1), k(Hg-caffeine) = 1.74 x 10(5) M(-1), k(Sr- caffeine) = 3.3 x 10(4) M(-1), k(Ba-caffeine) = 1.8 x 10(4) M(-1), k(Cd-theophylline) = 5.75 x 10(5) M(-1), k(Hg-theophylline) = 2.14 x 10(5) M(-1), k(Sr-theophylline) = 4.6 x 10(4) M(-1), k(Ba-theophylline) = 3 x 10(4) M(-1). These k values are evidence for weak and strong cation interactions in these metal complexes.     

Signal amplification architecture for electrochemical aptasensor based on network-like thiocyanuric acid/gold nanoparticle/ssDNA

A novel electrogenerated chemiluminescence (ECL) biosensor for highly sensitive and selective detection of mercury ion was developed on the basis of mercury-specific oligonucleotide (MSO) served as a molecular recognition element and the ruthenium(II) complex (Ru1) as an ECL emitting species. The biosensor was fabricated on a glassy carbon electrode coated with a thin layer of single wall carbon nanotubes, where the ECL probe, NH(2)-(CH(2))(6)-oligo(ethylene oxide)(6)-MSO?Dend-Ru1, was covalently attached. The Dend-Ru1 pendant was prepared by covalent coupling Ru1 with the 4th generation polyamidoamine dendrimer (Dend), in which each dendrimer contained 35 Ru1 units so that a large amplification of ECL signal was obtained. Upon binding of Hg(2+) to thymine (T) bases of the MSO, the T-Hg-T structure was formed, and the MSO changed from its linear shape to a "hairpin" configuration. Consequently, the Dend-Ru1 approached the electrode surface resulting in the increase of anodic ECL signal in the presence of the ECL coreactant tri-n-propylamine. The reported biosensor showed a high reproducibility and possessed long-term storage stability (92.3% initial ECL recovery over 30 day's storage). An extremely low detection limit of 2.4 pM and a large dynamic range of 7.0 pM to 50 nM Hg(2+) were obtained. An apparent binding constant of 1.6 × 10(9)M(-1) between Hg(2+) and the MSO was estimated using an ECL based extended Langmuir isotherm approach involving multilayer adsorption. Determination of Hg(2+) contents in real water samples was conducted and the data were consistent with the results from cold vapor atomic fluorescence spectroscopy.     

Label-free electrochemical detection of short sequences related to the hepatitis B virus using 4,4'-diaminoazobenzene based on multiwalled carbon nanotube-modified GCE

A novel label-free electrochemical DNA biosensor based on 4,4'-diaminoazobenzene (4,4'-DAAB) and multiwalled carbon nanotube (MWNT)-modified glassy carbon electrode (GCE) for short DNA sequences related to the hepatitis B virus (HBV) hybridization detection was presented. Differential pulse voltammetry (DPV) was used to investigate hybridization event. The decrease in the peak current of 4,4'-DAAB was observed on hybridization of probe with the target. This electrochemical approach was sequence specific as indicated by the control experiments, in which no peak current change was observed when a noncomplementary DNA sequence was used. Numerous factors affecting the target hybridization were optimized to maximize the sensitivity. Under optimal conditions, this sensor showed a good calibration range between 7.94 x 10(-8) M and 1.58 x 10(-6) M, with HBV DNA sequence detection limit of 1.1 x 10(-8) M.     

HRP/[Zn-Cr-ABTS] redox clay-based biosensor: design and optimization for cyanide detection

A novel inexpensive and simple amperometric biosensor, based on the immobilization of HRP into redox active [Zn-Cr-ABTS] layered double hydroxide, is applied to the determination of cyanide. The electrochemical transduction step corresponds to the reduction at 0.0 V of ABTS+* enzymatically formed in the presence of H2O2. The biosensor has a fast response to H2O2 (8s) with a linear range of 1.7 x 10(-9) to 2.1 x 10(-6) M and a sensitivity of 875 mA M(-1) cm(-2). The apparent Michaelis-Menten constant (KMapp) is 12 microM. The detection of cyanide is performed via its non competitive inhibiting action on the HRP/[Zn-Cr-ABTS] electrode. The concentration range of the linear response and the apparent inhibition constant (ki) are 5 x 10(-9) to 4 x 10(-8) and 1.4 x 10 (-7) M, respectively.     

Electrogenerated chemiluminescence biosensor with alcohol dehydrogenase and tris(2,2'-bipyridyl)ruthenium (II) immobilized in sol-gel hybrid material

An ethanol biosensor based on electrogenerated chemiluminescence detection was developed. Electrogenerated chemiluminescence reagent tris(2,2'-bipyridyl)ruthenium (II) and alcohol dehydrogenase were immobilized in the same sol-gel hybrid film. The copolymer poly(vinyl alcohol) with 4-vinylpyridine and cation exchanger Nafion were incorporated into sol-gel film to provide the microenvironment for retaining the activity of enzyme and immobilize tris(2,2'-bipyridyl)ruthenium (II). The design was simpler than the previous two-layer format. The experimental conditions, such as scan rate, pH and concentration of the cofactor were investigated. The intensity of electrogenerated chemiluminescence increased linearly with ethanol concentration from 2.5x10(-5) to 5.0x10(-2) M and detection limit was 1.0x10(-5) M. The prepared biosensor exhibited high sensitivity, wide linear range and good stability.     

Electrochemical DNA biosensor for the detection of interaction between di[azino-di(5,6-azafluorene)-kappa2-NN'] dibromicoppers and DNA

A new Cu(II) complex CuL(2)Br(2) (L = azino-di(5,6-azafluorene)-kappa(2)-NN') was synthesized, and a new method of electrochemical probe has been proposed for the determination of hepatitis B virus (HBV) based on its interaction with [CuL(2)](2+). This ligand, containing functional groups, as well as planar aromatic domains, is capable of binding to double-stranded DNA (dsDNA) more efficiently than to single-stranded DNA (ssDNA). Emphasis has been placed on the elucidation of the nature of the interaction by electrochemical techniques. The electroactive [CuL(2)](2+) could be employed as an electrochemical indicator to detect hybridization events in DNA biosensors. These biosensors have been constructed by immobilization of a probe DNA sequence from HBV onto glassy carbon electrode (GCE). After hybridization with the complementary target sequence, [CuL(2)](2+) was accumulated within the dsDNA layer. Electrochemical detection was performed by differential pulse voltammetry over the potential range. Using this approach, complementary target sequences of HBV can be quantified over the range of 1.74 x 10(-9) to 3.45 x 10(-7) M, with a detection limit of 8.32 x 10(-10) M and a linear correlation coefficient of 0.9936.In addition, this approach is capable of detecting hybridization of complementary sequences containing one or three mismatched bases.     

A novel enzymatic hydrogen peroxide biosensor based on Ag/C nanocables

A novel enzymatic hydrogen peroxide sensor was successfully fabricated based on the nanocomposites containing of Ag/C nanocables and gold nanoparticles (AuNPs). Ag/C nanocables have been synthesized by a hydrothermal method and then AuNPs were assembled on the surface of Ag/C nanocables. The nanocomposites were confirmed by X-ray diffraction (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM) and energy-dispersive X-ray spectrometry (EDS). The above nanocomposites have satisfactory chemical stability and excellent biocompatibility. Cyclic voltammetry (CV) was used to evaluate the electrochemical performance of the Ag/C/Au nanocomposites at glassy carbon electrode (GCE). The results indicated that the Ag/C/Au nanocomposites exhibited excellent electrocatalytic activity to the reduction of H(2)O(2). It offered a linear range of 6.7×10(-9) to 8.0×10(-6) M, with a detection limit of 2.2×10(-9) M. The apparent Michaelis-Menten constant of the biosensor was 51.7×10(-6) M. These results indicated that Ag/C/Au nanocomposites have potential for constructing of a variety of electrochemical biosensors.     

Linear free-energy analysis of mercury(II) and cadmium(II) binding to three-stranded coiled coils

Investigators have studied how proteins enforce nonstandard geometries on metal centers to assess the question of how protein structures can define the coordination geometry and binding affinity of an active-site metal cofactor. We have shown that cysteine-substituted versions of the TRI peptide series [AcG-(LKALEEK)(4)G-NH(2)] bind Hg(II) and Cd(II) in geometries that are different from what is normally found with thiol ligands in aqueous solution. A fundamental question has been whether this structural perturbation is due to protein influence or a change in the metal geometry preference. To address this question, we have completed linear free-energy analyses that correlate the association of three-stranded coiled coils in the absence of a metal with the binding affinity of the peptides to the heavy metals, Hg(II) and Cd(II). In this paper, six new members of this family have been synthesized, replacing core leucine residues with smaller and less hydrophobic residues, consequently leading to varying degrees of self-association affinities. At the same time, studies with some smaller and longer sequenced peptides have also been examined. All of these peptides are seen to sequester Hg(II) and Cd(II) in an uncommon trigonal environment. For both metals, the binding is strong with micromolar dissociation constants. For binding of Hg(II) to the peptides, the dissociation constants range from 2.4 x 10(-)(5) M for Baby L12C to 2.5 x 10(-)(9) M for Grand L9C for binding of the third thiolate to a linear Hg(II)(pep)(2) species. The binding of Hg(II) to the peptide Grand L9C is similar in energetics for metal binding in the metalloregulatory protein, mercury responsive (merR), displaying approximately 50% trigonal Hg(II) formation at nanomolar metal concentrations. Approximately, 11 kcal/mol of the Hg(II)(Grand L9C)(3)(-) stability is due to peptide interactions, whereas only 1-4 kcal/mol stabilization results from Hg(II)(RS)(2) binding the third thiolate ligand. This further validates the hypothesis that the favorable tertiary interactions in protein systems such as merR go a long way in stabilizing nonnatural coordination environments in biological systems. Similarly, for the binding of Cd(II) to the TRI family, the dissociation constants range from 1.3 x 10(-)(6) M for Baby L9C to 8.3 x 10(-)(9) M for TRI L9C, showing a similar nature of stable aggregate formation.     

Investigation of the interaction between ssDNA and 2-aminophenoxazine-3-one and development of an electrochemical DNA biosensor

An electrochemical method was used to probe the interaction between 2-aminophenoxazine-3-one (AP) and the short DNA sequence related to the hepatitis B virus (HBV), and an electrochemical DNA biosensor was developed. The voltammetric signals of AP have been investigated at bare glassy carbon electrode (bare GCE), hybrid double-stranded DNA-modified GCE (dsDNA/GCE), and single-stranded DNA-modified GCE (ssDNA/GCE) by means of differential pulse voltammetry (DPV), and the peak currents increased with respect to the order of electrodes. The extent of hybridization was evaluated on the basis of the difference between signals of AP with a probe before and after hybridization with the complementary sequence. Control experiments with noncomplementary were performed to test the selectivity of the biosensor. With this approach, a sequence of the HBV could be quantified over the range from 3.53 x 10(-7) to 1.08 x 10(-6) M, with a linear correlation of r = 0.9963 and a detection limit of 1.00 x 10(-7) M.     

An amperometric biosensor based on laccase immobilized onto Fe(3)O(4)NPs/cMWCNT/PANI/Au electrode for determination of phenolic content in tea leaves extract

A method is described for the construction of an amperometric biosensor for detection of phenolic compounds based on covalent immobilization of laccase onto iron oxide nanoparticles (Fe(3)O(4)NPs) decorated carboxylated multiwalled carbon nanotubes (cMWCNTs)/polyaniline (PANI) composite electrodeposited onto a gold (Au) electrode. The modified electrode was characterized by scanning electron microscopy (SEM), Fourier transform infrared (FTIR) spectroscopy, cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The biosensor showed optimum response within 3s at pH 6.0 (0.1M sodium acetate buffer) and 35°C, when operated at 0.3V vs. Ag/AgCl. Linear range, detection limit were 0.1-10μM (lower concentration range) and 10-500μM (higher concentration range), and 0.03μM respectively. The sensor measured total phenolic content in tea leaves extract. The enzyme electrode lost 25% of its initial activity after its 150 uses over a period of 4 months, when stored at 4°C.