Mechanical stresses in carotid plaques using MRI-based fluid-structure interaction models

Risk assessment in patients with carotid atherosclerosis relies on the degree of luminal stenosis. Incorporating morphological information on plaque composition obtained noninvasively through the use of magnetic resonance imaging (MRI) could include other variables besides the degree of stenosis into carotid plaque risk assessment. Knowledge of the morphologic composition of the plaque allows determination of mechanic stresses exerted on the protective fibrous cap, which may be of importance in the assessment of plaque vulnerability. Based on image processing of transverse MRI scans, longitudinal 2D fluid-structure interaction (FSI) simulations of carotid atherosclerotic plaques were performed facilitating in-vivo estimation of longitudinal internal fibrous cap stresses. The FSI simulation combined finite element analysis (FEA) with computational fluid dynamics (CFD) simulations of blood-flow variables. Preliminary results from two symptomatic patients revealed longitudinal stress levels (max. 254.1 and 143.2 kPa) approaching established criteria for plaque rupture at known predilection sites of plaque rupture. Determination of longitudinal fibrous cap stresses may prove useful in assessing plaque vulnerability and improve risk stratification in patients with carotid atherosclerosis.     

Study of carotid arterial plaque stress for symptomatic and asymptomatic patients

Stroke is one of the leading causes of death in the world, resulting mostly from the sudden ruptures of atherosclerosis carotid plaques. Until now, the exact plaque rupture mechanism has not been fully understood, and also the plaque rupture risk stratification. The advanced multi-spectral magnetic resonance imaging (MRI) has allowed the plaque components to be visualized in-vivo and reconstructed by computational modeling. In the study, plaque stress analysis using fully coupled fluid structure interaction was applied to 20 patients (12 symptomatic and 8 asymptomatic) reconstructed from in-vivo MRI, followed by a detailed biomechanics analysis, and morphological feature study. The locally extreme stress conditions can be found in the fibrous cap region, 85% at the plaque shoulder based on the present study cases. Local maximum stress values predicted in the plaque region were found to be significantly higher in symptomatic patients than that in asymptomatic patients (200 ± 43 kPa vs. 127 ± 37 kPa, p=0.001). Plaque stress level, defined by excluding 5% highest stress nodes in the fibrous cap region based on the accumulative histogram of stress experienced on the computational nodes in the fibrous cap, was also significantly higher in symptomatic patients than that in asymptomatic patients (154 ± 32 kPa vs. 111 ± 23 kPa, p<0.05). Although there was no significant difference in lipid core size between the two patient groups, symptomatic group normally had a larger lipid core and a significantly thinner fibrous cap based on the reconstructed plaques using 3D interpolation from stacks of 2D contours. Plaques with a higher stenosis were more likely to have extreme stress conditions upstream of plaque throat. The combined analyses of plaque MR image and plaque stress will advance our understanding of plaque rupture, and provide a useful tool on assessing plaque rupture risk.     

A Computer-Simulation Study on the Effects of MRI Voxel Dimensions on Carotid Plaque Lipid-Core and Fibrous Cap Segmentation and Stress Modeling

Background

The benefits of a decreased slice thickness and/or in-plane voxel size in carotid MRI for atherosclerotic plaque component quantification accuracy and biomechanical peak cap stress analysis have not yet been investigated in detail because of practical limitations.

Methods

In order to provide a methodology that allows such an investigation in detail, numerical simulations of a T1-weighted, contrast-enhanced, 2D MRI sequence were employed. Both the slice thickness (2 mm, 1 mm, and 0.5 mm) and the in plane acquired voxel size (0.62x0.62 mm² and 0.31x0.31 mm²) were varied. This virtual MRI approach was applied to 8 histology-based 3D patient carotid atherosclerotic plaque models.

Results

A decreased slice thickness did not result in major improvements in lumen, vessel wall, and lipid-rich necrotic core size measurements. At 0.62x0.62 mm² in-plane, only a 0.5 mm slice thickness resulted in improved minimum fibrous cap thickness measurements (a 2–3 fold reduction in measurement error) and only marginally improved peak cap stress computations. Acquiring voxels of 0.31x0.31 mm² in-plane, however, led to either similar or significantly larger improvements in plaque component quantification and computed peak cap stress.

Conclusions

This study provides evidence that for currently-used 2D carotid MRI protocols, a decreased slice thickness might not be more beneficial for plaque measurement accuracy than a decreased in-plane voxel size. The MRI simulations performed indicate that not a reduced slice thickness (i.e. more isotropic imaging), but the acquisition of anisotropic voxels with a relatively smaller in-plane voxel size could improve carotid plaque quantification and computed peak cap stress accuracy.     

Stress analysis of carotid plaque rupture based on in vivo high resolution MRI

Atheromatous carotid plaque rupture is responsible for the majority of ischaemic strokes in the developed world. Plaque rupture has been associated with plaque morphology, plaque components' properties, inflammation and local stress concentration. High resolution multi-spectral magnetic resonance imaging (MRI) has allowed the plaque components to be visualized in vivo. This study combined the recent advances in finite element analysis (FEA) and MRI, and performed stress analysis of five vulnerable carotid plaques based on the geometry derived from in vivo MRI. Image segmentation was based on multi-spectral MRI and co-registered with histology for plaque characterization. Plaque fibrous cap, lipid pool and vessel wall were modelled as isotropic, incompressible hyperelastic materials undergoing large deformation under pulse pressure loading. High stress concentrations were predicted at the shoulders and the thinnest fibrous cap regions of the plaque, and the mean maximal stresses were found to be higher in the ruptured plaques (683.3 kPa) than those in the unruptured plaques (226.9 kPa). The effect of the relative stiffness of fibrous cap to lipid pool on the stress within the cap itself was studied. It was shown that larger relative stiffness of fibrous cap to lipid pool resulted in higher stress within the cap. Thus, it is likely that high stress concentrations in vulnerable plaque may cause plaque rupture and lead to acute ischaemic sequelae. A combination of in vivo high resolution MRI and FEA could potentially act as a useful tool to assess plaque vulnerability and risk stratify patients with carotid atheroma.     

The effects of plaque morphology and material properties on peak cap stress in human coronary arteries

Heart attacks are often caused by rupture of caps of atherosclerotic plaques in coronary arteries. Cap rupture occurs when cap stress exceeds cap strength. We investigated the effects of plaque morphology and material properties on cap stress. Histological data from 77 coronary lesions were obtained and segmented. In these patient-specific cross sections, peak cap stresses were computed by using finite element analyses. The finite element analyses were 2D, assumed isotropic material behavior, and ignored residual stresses. To represent the wide spread in material properties, we applied soft and stiff material models for the intima. Measures of geometric plaque features for all lesions were determined and their relations to peak cap stress were examined using regression analyses. Patient-specific geometrical plaque features greatly influence peak cap stresses. Especially, local irregularities in lumen and necrotic core shape as well as a thin intima layer near the shoulder of the plaque induce local stress maxima. For stiff models, cap stress increased with decreasing cap thickness and increasing lumen radius (R = 0.79). For soft models, this relationship changed: increasing lumen radius and increasing lumen curvature were associated with increased cap stress (R = 0.66). The results of this study imply that not only accurate assessment of plaque geometry, but also of intima properties is essential for cap stress analyses in atherosclerotic plaques in human coronary arteries.     

Initial stress in biomechanical models of atherosclerotic plaques

Rupture of atherosclerotic plaques is the underlying cause for the majority of acute strokes and myocardial infarctions. Rupture of the plaque occurs when the stress in the plaque exceeds the strength of the material locally. Biomechanical stress analyses are commonly based on pressurized geometries, in most cases measured by in-vivo MRI. The geometry is therefore not stress-free. The aim of this study is to identify the effect of neglecting the initial stress state on the plaque stress distribution. Fifty 2D histological sections (7 patients, 9 diseased coronary artery segments), perfusion fixed at 100 mmHg, were segmented and finite element models were created. The Backward Incremental method was applied to determine the initial stress state and the zero-pressure state. Peak plaque and cap stresses were compared with and without initial stress. The effect of initial stress on the peak stress was related to the minimum cap thickness, maximum necrotic core thickness, and necrotic core angle. When accounting for initial stress, the general relations between geometrical features and peak cap stress remain intact. However, on a patient-specific basis, accounting for initial stress has a different effect on the absolute cap stress for each plaque. Incorporating initial stress may therefore improve the accuracy of future stress based rupture risk analyses for atherosclerotic plaques.     

The influence of vascular anatomy on carotid artery stenting: A parametric study for damage assessment

Carotid artery stenting is emerging as an alternative technique to surgery for the treatment of symptomatic severe carotid stenosis. Clinical and experimental evidence demonstrates that both plaque morphology and biomechanical changes due to the device implantation can be possible causes of an unsuccessful treatment. In order to gain further insights of the endovascular intervention, a virtual environment based on structural finite element simulations was built to emulate the stenting procedure on generalized atherosclerotic carotid geometries which included a damage model to quantify the injury of the vessel. Five possible lesion scenarios were simulated by changing both material properties and vascular geometrical features to cover both presumed vulnerable and stable plaques. The results were analyzed with respect to lumen gain and wall stresses which are potentially related to the failure of the procedure according to previous studies. Our findings show that an elliptic lumen shape and a thinner fibrous cap with an underlying lipid pool result in higher stenosis reduction, while large calcifications and fibrotic tissue are more prone to recoil. The shielding effect of a thicker fibrous cap helps to reduce local compressive stresses in the soft plaque. The presence of a soft plaque reduces the damage in the healthy vascular structures. Contrarily, the presence of hard plaque promotes less damage volume in the fibrous cap and reduces stress peaks in this region, but they seem to increase stresses in the media-intima layer. Finally the reliability of the achieved results was put into clinical perspective.     

Using in vivo Cine and 3D multi-contrast MRI to determine human atherosclerotic carotid artery material properties and circumferential shrinkage rate and their impact on stress/strain predictions

In vivo magnetic resonance image (MRI)-based computational models have been introduced to calculate atherosclerotic plaque stress and strain conditions for possible rupture predictions. However, patient-specific vessel material properties are lacking in those models, which affects the accuracy of their stress/strain predictions. A noninvasive approach of combining in vivo Cine MRI, multicontrast 3D MRI, and computational modeling was introduced to quantify patient-specific carotid artery material properties and the circumferential shrinkage rate between vessel in vivo and zero-pressure geometries. In vivo Cine and 3D multicontrast MRI carotid plaque data were acquired from 12 patients after informed consent. For each patient, one nearly-circular slice and an iterative procedure were used to quantify parameter values in the modified Mooney-Rivlin model for the vessel and the vessel circumferential shrinkage rate. A sample artery slice with and without a lipid core and three material parameter sets representing stiff, median, and soft materials from our patient data were used to demonstrate the effect of material stiffness and circumferential shrinkage process on stress/strain predictions. Parameter values of the Mooney-Rivlin models for the 12 patients were quantified. The effective Young's modulus (YM, unit: kPa) values varied from 137 (soft), 431 (median), to 1435 (stiff), and corresponding circumferential shrinkages were 32%, 12.6%, and 6%, respectively. Using the sample slice without the lipid core, the maximum plaque stress values (unit: kPa) from the soft and median materials were 153.3 and 96.2, which are 67.7% and 5% higher than that (91.4) from the stiff material, while the maximum plaque strain values from the soft and median materials were 0.71 and 0.293, which are about 700% and 230% higher than that (0.089) from the stiff material, respectively. Without circumferential shrinkages, the maximum plaque stress values (unit: kPa) from the soft, median, and stiff models were inflated to 330.7, 159.2, and 103.6, which were 116%, 65%, and 13% higher than those from models with proper shrinkage. The effective Young's modulus from the 12 human carotid arteries studied varied from 137 kPa to 1435 kPa. The vessel circumferential shrinkage to the zero-pressure condition varied from 6% to 32%. The inclusion of proper shrinkage in models based on in vivo geometry is necessary to avoid over-estimating the stresses and strains by up 100%. Material stiffness had a greater impact on strain (up to 700%) than on stress (up to 70%) predictions. Accurate patient-specific material properties and circumferential shrinkage could considerably improve the accuracy of in vivo MRI-based computational stress/strain predictions.     

Patient-Specific Artery Shrinkage and 3D Zero-Stress State in Multi-Component 3D FSI Models for Carotid Atherosclerotic Plaques Based on <i>In Vivo</i> MRI Data

Image-based computational models for atherosclerotic plaques have been developed to perform mechanical analysis to quantify critical flow and stress/strain conditions related to plaque rupture which often leads directly to heart attack or stroke. An important modeling issue is how to determine zero stress state from in vivo plaque geometries. This paper presents a method to quantify human carotid artery axial and inner circumferential shrinkages by using patient-specific ex vivo and in vivo MRI images. A shrink-stretch process based on patient-specific in vivo plaque morphology and shrinkage data was introduced to shrink the in vivo geometry first to find the zero-stress state (opening angle was ignored to reduce the complexity), and then stretch and pressurize to recover the in vivo plaque geometry with computed initial stress, strain, flow pressure and velocity conditions. Effects of the shrink-stretch process on plaque stress/strain distributions were demonstrated based on patient-specific data using 3D models with fluid-structure interactions (FSI). The average artery axial and inner circumferential shrinkages were 25% and 7.9%, respectively, based on a data set obtained from 10 patients. Maximum values of maximum principal stress and strain increased 349.8% and 249% respectively with 33% axial stretch. Influence of inner circumferential shrinkage (7.9%) was not very noticeable under 33% axial stretch, but became more noticeable under smaller axial stretch. Our results indicated that accurate knowledge of artery shrinkages and the shrink-stretch process will considerably improve the accuracy of computational predictions made based on results from those in vivo MRI-based FSI models.     

Lumen irregularity dominates the relationship between mechanical stress condition, fibrous-cap thickness, and lumen curvature in carotid atherosclerotic plaque

High mechanical stress condition over the fibrous cap (FC) has been widely accepted as a contributor to plaque rupture. The relationships between the stress, lumen curvature, and FC thickness have not been explored in detail. In this study, we investigate lumen irregularity-dependent relationships between mechanical stress conditions, local FC thickness (LT(FC)), and lumen curvature (LC(lumen)). Magnetic resonance imaging slices of carotid plaque from 100 patients with delineated atherosclerotic components were used. Two-dimensional structure-only finite element simulations were performed for the mechanical analysis, and maximum principal stress (stress-P?) at all integral nodes along the lumen was obtained. LT(FC) and LC(lumen) were computed using the segmented contour. The lumen irregularity (L-δir) was defined as the difference between the largest and the smallest lumen curvature. The results indicated that the relationship between stress-P?, LT(FC), and LC(lumen) is largely dependent on L-δir. When L-δir ≥ .31 (irregular lumen), stress-P? strongly correlated with lumen curvature and had a weak/no correlation with local FC thickness, and in 73.4% of magnetic resonance (MR) slices, the critical stress (maximum of stress-P? over the diseased region) was found at the site where the lumen curvature was large. When L-δir ≤ 0.28 (relatively round lumen), stress-P? showed a strong correlation with local FC thickness but weak/no correlation with lumen curvature, and in 71.7% of MR slices, the critical stress was located at the site of minimum FC thickness. Using lumen irregularity as a method of identifying vulnerable plaque sites by referring to the lumen shape is a novel and simple method, which can be used for mechanics-based plaque vulnerability assessment.     

Flow pattern analysis in a highly stenotic patient-specific carotid bifurcation model using a turbulence model

The aim of this study is to investigate the blood flow pattern in carotid bifurcation with a high degree of luminal stenosis, combining in vivo magnetic resonance imaging (MRI) and computational fluid dynamics (CFD). A newly developed two-equation transitional model was employed to evaluate wall shear stress (WSS) distribution and pressure drop across the stenosis, which are closely related to plaque vulnerability. A patient with an 80% left carotid stenosis was imaged using high resolution MRI, from which a patient-specific geometry was reconstructed and flow boundary conditions were acquired for CFD simulation. A transitional model was implemented to investigate the flow velocity and WSS distribution in the patient-specific model. The peak time-averaged WSS value of approximately 73 Pa was predicted by the transitional flow model, and the regions of high WSS occurred at the throat of the stenosis. High oscillatory shear index values up to 0.50 were present in a helical flow pattern from the outer wall of the internal carotid artery immediately after the throat. This study shows the potential suitability of a transitional turbulent flow model in capturing the flow phenomena in severely stenosed carotid arteries using patient-specific MRI data and provides the basis for further investigation of the links between haemodynamic variables and plaque vulnerability. It may be useful in the future for risk assessment of patients with carotid disease.     

Carotid arterial plaque stress analysis using fluid–structure interactive simulation based on in-vivo magnetic resonance images of four patients

The rupture of atherosclerotic plaques is known to be associated with the stresses that act on or within the arterial wall. The extreme wall tensile stress (WTS) is usually recognized as a primary trigger for the rupture of vulnerable plaque. The present study used the in-vivo high-resolution multi-spectral magnetic resonance imaging (MRI) for carotid arterial plaque morphology reconstruction. Image segmentation of different plaque components was based on the multi-spectral MRI and co-registered with different sequences for the patient. Stress analysis was performed on totally four subjects with different plaque burden by fluid–structure interaction (FSI) simulations. Wall shear stress distributions are highly related to the degree of stenosis, while the level of its magnitude is much lower than the WTS in the fibrous cap. WTS is higher in the luminal wall and lower at the outer wall, with the lowest stress at the lipid region. Local stress concentrations are well confined in the thinner fibrous cap region, and usually locating in the plaque shoulder; the introduction of relative stress variation during a cycle in the fibrous cap can be a potential indicator for plaque fatigue process in the thin fibrous cap. According to stress analysis of the four subjects, a risk assessment in terms of mechanical factors could be made, which may be helpful in clinical practice. However, more subjects with patient specific analysis are desirable for plaque-stability study.     

Model-based cap thickness and peak cap stress prediction for carotid MRI

A rupture-prone carotid plaque can potentially be identified by calculating the peak cap stress (PCS). For these calculations, plaque geometry from MRI is often used. Unfortunately, MRI is hampered by a low resolution, leading to an overestimation of cap thickness and an underestimation of PCS. We developed a model to reconstruct the cap based on plaque geometry to better predict cap thickness and PCS.We used histological stained plaques from 34 patients. These plaques were segmented and served as the ground truth. Sections of these plaques contained 93 necrotic cores with a cap thickness <0.62 mm which were used to generate a geometry-based model. The histological data was used to simulate in vivo MRI images, which were manually delineated by three experienced MRI readers. Caps below the MRI resolution (n = 31) were (digitally removed and) reconstructed according to the geometry-based model. Cap thickness and PCS were determined for the ground truth, readers, and reconstructed geometries.Cap thickness was 0.07 mm for the ground truth, 0.23 mm for the readers, and 0.12 mm for the reconstructed geometries. The model predicts cap thickness significantly better than the readers. PCS was 464 kPa for the ground truth, 262 kPa for the readers and 384 kPa for the reconstructed geometries. The model did not predict the PCS significantly better than the readers.The geometry-based model provided a significant improvement for cap thickness estimation and can potentially help in rupture-risk prediction, solely based on cap thickness. Estimation of PCS estimation did not improve, probably due to the complex shape of the plaques.     

Finite element analysis of mechanics of neovessels with intraplaque hemorrhage in carotid atherosclerosis

Background

Intraplaque hemorrhage is a widely known factor facilitating plaque instability. Neovascularization of plaque can be regarded as a compensatory response to the blood supply in the deep intimal and medial areas of the artery. Due to the physiological function, the deformation of carotid atherosclerotic plaque would happen under the action of blood pressure and blood flow. Neovessels are subject to mechanical loading and likely undergo deformation. The rupture of neovessels may deteriorate the instability of plaque. This study focuses on the local mechanical environments around neovessels and investigates the relationship between the biomechanics and the morphological specificity of neovessels.

Methods

Stress and stretch were used to evaluate the rupture risk of the neovessels in plaque. Computational structural analysis was performed based on two human carotid plaque slice samples. Two-dimensional models containing neovessels and other components were built according to the plaque slice samples. Each component was assumed to be non-linear isotropic, piecewise homogeneous and incompressible. Different mechanical boundary conditions, i.e. static pressures, were imposed in the carotid lumen and neovessels lumen respectively. Finite element method was used to simulate the mechanical conditions in the atherosclerotic plaque.

Results

Those neovessels closer to the carotid lumen undergo larger stress and stretch. With the same distance to the carotid lumen, the longer the perimeter of neovessels is, the larger stress and the deformation of the neovessels will be. Under the same conditions, the neovessels with larger curvature suffer greater stress and stretch. Neovessels surrounded by red blood cells undergo a much larger stretch.

Conclusions

Local mechanical conditions may result in the hemorrhage of neovessels and accelerate the rupture of plaque. The mechanical environments of the neovessel are related to its shape, curvature, distance to the carotid lumen and the material properties of plaque.

     

Association between carotid plaque characteristics and cerebral white matter lesions: one-year follow-up study by MRI

Objective

To prospectively assess the relation between carotid plaque characteristics and the development of new cerebral white matter lesions (WMLs) at MRI.

Methods

Fifty TIA/stroke patients with ipsilateral 30–69% carotid stenosis underwent MRI of the plaque at baseline. Total plaque volume and markers of vulnerability to thromboembolism (lipid-rich necrotic core [LRNC] volume, fibrous cap [FC] status, and presence of intraplaque hemorrhage [IPH]) were assessed. All patients also underwent brain MRI at baseline and after one year. Ipsilateral cerebral WMLs were quantified with a semiautomatic method.

Results

Mean WML volume significantly increased over a one-year period (6.52 vs. 6.97 mm³, P = 0.005). WML volume at baseline and WML progression did not significantly differ (P>0.05) between patients with 30–49% and patients with 50–69% stenosis. There was a significant correlation between total plaque volume and baseline ipsilateral WML volume (Spearman ρ = 0.393, P = 0.005). There was no significant correlation between total plaque volume and ipsilateral WML progression. There were no significant associations between LRNC volume and WML volume at baseline and WML progression. WML volume at baseline and WML progression did not significantly differ between patients with a thick and intact FC and patients with a thin and/or ruptured FC. WML volume at baseline and WML progression also did not significantly differ between patients with and without IPH.

Conclusion

The results of this study indicate that carotid plaque burden is significantly associated with WML severity, but that there is no causal relationship between carotid plaque vulnerability and the occurrence of WMLs.     

Mechanical action of the blood onto atheromatous plaques: influence of the stenosis shape and morphology

The vulnerability of atheromatous plaques in the carotid artery may be related to several factors, the most important being the degree of severity of the endoluminal stenosis and the thickness of the fibrous cap. It has recently been shown that the plaque length can also affect the mechanical response significantly. However, in their study on the effect of the plaque length, the authors did not consider the variations of the plaque morphology and the shape irregularities that may exist independently of the plaque length. These aspects are developed in this paper. The mechanical interactions between the blood flow and an atheromatous plaque are studied through a numerical model considering fluid–structure interaction. The simulation is achieved using the arbitrary Lagrangian–Eulerian scheme in the COMSOL TM commercial finite element package. The stenosis severity and the plaque length are, respectively, set to 45% and 15 mm. Different shapes of the stenosis are modelled, considering irregularities made of several bumps over the plaque. The resulting flow patterns, wall shear stresses, plaque deformations and stresses in the fibrous cap reveal that the effects of the blood flow are amplified if the slope upstream stenosis is steep or if the plaque morphology is irregular with bumps. More specifically, the maximum stress in the fibrous cap is 50% larger for a steep slope than for a gentle slope. These results offer new perspectives for considering the shape of plaques in the evaluation of the vulnerability.     

Stress-Based Plaque Vulnerability Index and Assessment for Carotid Atherosclerotic Plaques Using Patient-Specific Vessel Material Properties

Cardiovascular diseases are closely linked to atherosclerotic plaque development and rupture. Assessment of plaque vulnerability is of fundamental significance to cardiovascular research and disease diagnosis, prevention, treatment and management. Magnetic resonance image (MRI) data of carotid atherosclerotic plaques from 8 patients (5 male, 3 female; age: 62-83, mean=71) were acquired at the University of Washington (UW), Seattle by the Vascular Imaging Laboratory (VIL) with written informed consent obtained. Patient-specific vessel material properties were quantified using Cine MRI data for modeling use. 3D thin-layer models were used to obtain plaque stress and strain for plaque assessment. A stress-based plaque vulnerability index (SPVI) was proposed to combine mechanical analysis, plaque morphology and composition for more complete carotid plaque vulnerability assessment. The five intervals (unit: kPa) [0, 46.8), [46.8, 80), [80, 92), [92, 103), and [103, +∞) from in vivo material models were used for SPVI values of 0, 1, 2, 3 and 4, respectively. The optimized agreement rate was 85.19%. The use of patient-specific material properties in plaque models could potentially improve the accuracy of model stress/strain calculations. SPVI has the potential to improve the current image-based screening and plaque vulnerability assessment schemes.     

Longitudinal MRI study on the natural history of carotid artery plaques in symptomatic patients

Purpose

To investigate the natural history of carotid atherosclerosis in patients who experienced a TIA or ischemic stroke.

Patients and Methods

Ninety-two TIA/stroke patients (57 men, mean age 67.7±9.8 years) with ipsilateral <70% carotid stenosis underwent multisequence MRI of the plaque ipsilateral to the symptomatic side at baseline and after one year. For each plaque, several parameters were assessed at both time points.

Results

Carotid lumen, wall and total vessel ( = carotid lumen and wall) volume did not significantly change. Forty-four patients had a plaque with a lipid-rich necrotic core (LRNC) at baseline, of which 34 also had a LRNC after one year. In three patients a LRNC appeared after one year. Thirty patients had a plaque with a thin and/or ruptured fibrous cap (FC) at both time points. In seven patients, FC status changed from thin and/or ruptured into thick and intact. In three patients, FC status changed from thick and intact into thin and/or ruptured. Twenty patients had intraplaque hemorrhage (IPH) at both time points. In four patients, IPH disappeared, whereas in three patients, new IPH appeared at follow-up.

Conclusion

In TIA/stroke patients, carotid plaque morphology does not significantly change over a one-year period. IPH and FC status change in a minority of patients.     

Quantifying effects of plaque structure and material properties on stress distributions in human atherosclerotic plaques using 3D FSI models

BACKGROUND: Atherosclerotic plaques may rupture without warning and cause acute cardiovascular syndromes such as heart attack and stroke. Methods to assess plaque vulnerability noninvasively and predict possible plaque rupture are urgently needed. METHOD: MRI-based three-dimensional unsteady models for human atherosclerotic plaques with multi-component plaque structure and fluid-structure interactions are introduced to perform mechanical analysis for human atherosclerotic plaques. RESULTS: Stress variations on critical sites such as a thin cap in the plaque can be 300% higher than that at other normal sites. Large calcification block considerably changes stress/strain distributions. Stiffness variations of plaque components (50% reduction or 100% increase) may affect maximal stress values by 20-50%. Plaque cap erosion causes almost no change on maximal stress level at the cap, but leads to 50% increase in maximal strain value. CONCLUSIONS: Effects caused by atherosclerotic plaque structure, cap thickness and erosion, material properties, and pulsating pressure conditions on stress/strain distributions in the plaque are quantified by extensive computational case studies and parameter evaluations. Computational mechanical analysis has good potential to improve accuracy of plaque vulnerability assessment.     

Local critical stress correlates better than global maximum stress with plaque morphological features linked to atherosclerotic plaque vulnerability: an in vivo multi-patient study

Background  

It is believed that mechanical stresses play an important role in atherosclerotic plaque rupture process and may be used for better plaque vulnerability assessment and rupture risk predictions. Image-based plaque models have been introduced in recent years to perform mechanical stress analysis and identify critical stress indicators which may be linked to rupture risk. However, large-scale studies based on in vivo patient data combining mechanical stress analysis, plaque morphology and composition for carotid plaque vulnerability assessment are lacking in the current literature.