Liquid chromatography MALDI MS/MS for membrane proteome analysis

Membrane proteins play critical roles in many biological functions and are often the molecular targets for drug discovery. However, their analysis presents a special challenge largely due to their highly hydrophobic nature. We present a surfactant-aided shotgun proteomics approach for membrane proteome analysis. In this approach, membrane proteins were solubilized and digested in the presence of SDS followed by newly developed auto-offline liquid chromatography/matrix-assisted laser desorption ionization (LC/MALDI) tandem MS analysis. Because of high tolerance of MALDI to SDS, one-dimensional (1D) LC separation can be combined with MALDI for direct analysis of protein digests containing SDS, without the need for extensive sample cleanup. In addition, the heated droplet interface used in LC/MALDI can work with high flow LC separations, allowing a relatively large amount of protein digest to be used for 1D LC/MALDI which facilitates the detection of low abundance proteins. The proteome identification results obtained by LC/MALDI are compared to the gel electrophoresis/MS method as well as the shotgun proteomics method using 2D LC/electrospray ionization MS. It is demonstrated that, while LC/MALDI provides more extensive proteome coverage compared to the other two methods, these three methods are complementary to each other and a combination of these methods should provide a more comprehensive membrane proteome analysis.     

Automated protein identification by the combination of MALDI MS and MS/MS spectra from different instruments

The identification of proteins separated on two-dimensional gels is most commonly performed by trypsin digestion and subsequent matrix-assisted laser desorption ionization (MALDI) with time-of-flight (TOF). Recently, atmospheric pressure (AP) MALDI coupled to an ion trap (IT) has emerged as a convenient method to obtain tandem mass spectra (MS/MS) from samples on MALDI target plates. In the present work, we investigated the feasibility of using the two methodologies in line as a standard method for protein identification. In this setup, the high mass accuracy MALDI-TOF spectra are used to calibrate the peptide precursor masses in the lower mass accuracy AP-MALDI-IT MS/MS spectra. Several software tools were developed to automate the analysis process. Two sets of MALDI samples, consisting of 142 and 421 gel spots, respectively, were analyzed in a highly automated manner. In the first set, the protein identification rate increased from 61% for MALDI-TOF only to 85% for MALDI-TOF combined with AP-MALDI-IT. In the second data set the increase in protein identification rate was from 44% to 58%. AP-MALDI-IT MS/MS spectra were in general less effective than the MALDI-TOF spectra for protein identification, but the combination of the two methods clearly enhanced the confidence in protein identification.     

An Efficient In-gel Digestion Protocol for Mass Spectral Analysis by MALDI-TOF-MS and MS/MS and Its Use for Proteomic Analysis of Vigna mungo Leaves

An efficient protocol for in-gel digestion of Coomassie-stained protein spots has been established for mass analysis by matrix-assisted laser desorption/ionization-mass spectrometry (MS) and for tandem mass spectrometry (MS/MS). Identification of Vigna mungo leaf proteome from two-dimensional gel electrophoresis was done employing the protocol. About 300 proteins spots were consistently detected in three replicate gels. Optimization of the destaining process, digestion using 25 ng/μl trypsin in 20 μl trypsin buffer, and omission of peptide extraction step significantly increased the number of matched peptides and sequence coverage. Reliable characterization of 109 proteins by MS as well as tandem sequencing by MS/MS (PRIDE Accession no. 15318) suggests the potential application of the modified protocol for high throughput proteome analysis to unravel disputes in characterization of plant proteins in fundamental or applied research.     

Matrix layer sample preparation: an improved MALDI-MS peptide analysis method for proteomic studies

The analytical performance of MALDI-MS is highly influenced by sample preparation and the choice of matrix. Here we present an improved MALDI-MS sample preparation method for peptide mass mapping and peptide analysis, based on the use of the 2,5-dihydroxybenzoic acid matrix and prestructured sample supports, termed: matrix layer (ML). This sample preparation is easy to use and results in a rapid automated MALDI-MS and MS/MS with high quality spectra acquisition. The between-spot variation was investigated using standard peptides and statistical treatment of data confirmed the improvement gained with the ML method. Furthermore, the sample preparation method proved to be highly sensitive, in the lower-attomole range for peptides, and we improved the performance of MALDI-MS/MS for characterization of phosphopeptides as well. The method is versatile for the routine analysis of in-gel tryptic digests thereby allowing for an improved protein sequence coverage. Furthermore, reliable protein identification can be achieved without the need of desalting sample preparation. We demonstrate the performance and the robustness of our method using commercially available reference proteins and automated MS and MS/MS analyses of in-gel digests from lung tissue lysate proteins separated by 2-DE.     

Quantitative proteome analysis using differential stable isotopic labeling and microbore LC-MALDI MS and MS/MS

We demonstrate an approach for global quantitative analysis of protein mixtures using differential stable isotopic labeling of the enzyme-digested peptides combined with microbore liquid chromatography (LC) matrix-assisted laser desorption ionization (MALDI) mass spectrometry (MS). Microbore LC provides higher sample loading, compared to capillary LC, which facilitates the quantification of low abundance proteins in protein mixtures. In this work, microbore LC is combined with MALDI MS via a heated droplet interface. The compatibilities of two global peptide labeling methods (i.e., esterification to carboxylic groups and dimethylation to amine groups of peptides) with this LC-MALDI technique are evaluated. Using a quadrupole-time-of-flight mass spectrometer, MALDI spectra of the peptides in individual sample spots are obtained to determine the abundance ratio among pairs of differential isotopically labeled peptides. MS/MS spectra are subsequently obtained from the peptide pairs showing significant abundance differences to determine the sequences of selected peptides for protein identification. The peptide sequences determined from MS/MS database search are confirmed by using the overlaid fragment ion spectra generated from a pair of differentially labeled peptides. The effectiveness of this microbore LC-MALDI approach is demonstrated in the quantification and identification of peptides from a mixture of standard proteins as well as E. coli whole cell extract of known relative concentrations. It is shown that this approach provides a facile and economical means of comparing relative protein abundances from two proteome samples.     

Optimization of a phenol extraction‐based protein preparation method amenable to downstream 2DE and MALDI‐MS based analysis of bacterial proteomes

2DE is one of the most efficient and widely used methods for resolving complex protein mixtures. For efficient analysis of complex samples, high‐resolution separation of proteins on 2D gel is essential, and for that purpose good sample preparation is crucial. In this study, we have improvized a method for preparing bacterial total cellular proteome, from a strategy applied earlier to recalcitrant plant tissues, which gave high‐quality resolution on 2DE. The method involving phenol extraction followed by methanol/ammonium acetate precipitation was first optimized for the chemolithotrophic proteobacteria Tetrathiobacter kashmirensis WT001 and Pseudaminobacter salicylatoxidans KCT001 that did not yield quality protein preps in conventional trichloroacetic acid/acetone precipitation method. Subsequently, to validate its general applicability, the method was evaluated against the trichloroacetic acid/acetone precipitation method for two other model bacteria, i.e. Escherichia coli DH5α and Mycobacterium smegmatis mc²6. Identification of at least four proteins each from the outer membrane, periplasm, and cytoplasm of T. kashmirensis by MALDI‐MS not only proved the efficiency of the method in extracting proteins from the different cellular compartments but also the amenability of the obtained protein spots toward MALDI‐MS based identification.     

Improvement of an in-gel tryptic digestion method for matrix-assisted laser desorption/ionization-time of flight mass spectrometry peptide mapping by use of volatile solubilizing agents

The combination of matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI-TOF MS), in-gel enzymatic digestion of proteins separated by two-dimensional gel electrophoresis and searches of molecular weight in peptide-mass databases is a powerful and well established method for protein identification in proteomics analysis. For successful protein identification by MALDI-TOF mass spectrometry of peptide mixtures, critical parameters include highly specific enzymatic cleavage, high mass accuracy and sufficient numbers and sequence coverage of the peptides which can be analyzed. For in-gel digestion with trypsin, the method employed should be compatible both with enzymatic cleavage and subsequent MALDI-TOF MS analysis. We report here an improved method for preparation of peptides for MALDI-TOF MS mass fingerprinting by using volatile solubilizing agents during the in-gel digestion procedure. Our study clearly demonstrates that modification of the in-gel digestion protocols by addition of dimethyl formamide (DMF) or a mixture of DMF/N,N-dimethyl acetamide at various concentrations can significantly increase the recovery of peptides. These higher yields of peptides resulted in more effective protein identification.     

Evaluation of sample preparation methods for the analysis of papaya leaf proteins through two‐dimensional gel electrophoresis

Introduction – A variety of sample preparation protocols for plant proteomic analysis using two‐dimensional gel electrophoresis (2‐DE) have been reported. However, they usually have to be adapted and further optimised for the analysis of plant species not previously studied. Objective – This work aimed to evaluate different sample preparation protocols for analysing Carica papaya L. leaf proteins through 2‐DE. Methodology – Four sample preparation methods were tested: (1) phenol extraction and methanol–ammonium acetate precipitation; (2) no precipitation fractionation; and the traditional trichloroacetic acid–acetone precipitation either (3) with or (4) without protein fractionation. The samples were analysed for their compatibility with SDS–PAGE (1‐DE) and 2‐DE. Fifteen selected protein spots were trypsinised and analysed by matrix‐assisted laser desorption/ionisation time‐of‐flight tandem mass spectrometry (MALDI‐TOF‐MS/MS), followed by a protein search using the NCBInr database to accurately identify all proteins. Results – Methods number 3 and 4 resulted in large quantities of protein with good 1‐DE separation and were chosen for 2‐DE analysis. However, only the TCA method without fractionation (no. 4) proved to be useful. Spot number and resolution advances were achieved, which included having an additional solubilisation step in the conventional TCA method. Moreover, most of the theoretical and experimental protein molecular weight and pI data had similar values, suggesting good focusing and, most importantly, limited protein degradation. Conclusion – The described sample preparation method allows the proteomic analysis of papaya leaves by 2‐DE and mass spectrometry (MALDI‐TOF‐MS/MS). The methods presented can be a starting point for the optimisation of sample preparation protocols for other plant species. Copyright © 2009 John Wiley & Sons, Ltd.     

Profiling of myelin proteins by 2D-gel electrophoresis and multidimensional liquid chromatography coupled to MALDI TOF-TOF mass spectrometry

The myelin sheath is an electrically insulating layer that consists of lipids and proteins. It plays a key role in the functioning of the nervous system by allowing fast saltatory conduction of nerve pulses. Profiling of the proteins present in myelin is an indispensable prerequisite to better understand the molecular aspects of this dynamic, functionally active membrane. Two types of protein, the myelin basic protein and the proteolipid protein, account for nearly 85% of the protein content in myelin. Identification and characterization of the other "minor" proteins is, in this respect, a real challenge. In the present work, two proteomic strategies were applied in order to study the protein composition of myelin from the murine central nervous system. First, the protein mixture was separated by 2D-gel electrophoresis and, after spot excision and in-gel digestion, samples were analyzed by mass spectrometry. Via this approach, we identified 57 protein spots, corresponding to 38 unique proteins. Alternatively, the myelin sample was digested by trypsin and the resulting peptide mixture was further analyzed by off-line 2D-liquid chromatography. After the second-dimension separation (nanoLC), the peptides were spotted "on-line" onto a MALDI target and analyzed by MALDI TOF-TOF mass spectrometry. We identified 812 peptides by MALDI MS/MS, representing 93 proteins. Membrane proteins, low abundant proteins, and highly basic proteins were all represented in this shotgun proteomic approach. By combining the results of both approaches, we can present a comprehensive proteomic map of myelin, comprising a total of 103 protein identifications, which is of utmost importance for the molecular understanding of white matter and its disorders.     

Improved Identification of Membrane Proteins by MALDI-TOF MS/MS Using Vacuum Sublimated Matrix Spots on an Ultraphobic Chip Surface

Integral membrane proteins are notoriously difficult to identify and analyze by mass spectrometry because of their low abundance and limited number of trypsin cleavage sites. Our strategy to address this problem is based on a novel technology for MALDI-MS peptide sample preparation that increases the success rate of membrane protein identification by increasing the sensitivity of the MALDI-TOF system. For this, we used sample plates with predeposited matrix spots of CHCA crystals prepared by vacuum sublimation onto an extremely low wettable (ultraphobic) surface. In experiments using standard peptides, an up to 10-fold gain of sensitivity was found for on-chip preparations compared with classical dried-droplet preparations on a steel target. In order to assess the performance of the chips with membrane proteins, three model proteins (bacteriorhodopsin, subunit IV(a) of ATP synthase, and the cp47 subunit from photosystem II) were analyzed. To mimic realistic analysis conditions, purified proteins were separated by SDS-PAGE and digested with trypsin. The digest MALDI samples were prepared either by dried-droplet technique on steel plates using CHCA as matrix, or applied directly onto the matrix spots of the chip surface. Significantly higher signal-to-noise ratios were observed for all of the spectra resulting from on-chip preparations of different peptides.In a second series of experiments, the membrane proteome of Rhodococcus jostii RHA1 was investigated by AIEC/SDS-PAGE in combination with MALDI-TOF MS/MS. As in the first experiments, Coomassie-stained SDS-PAGE bands were digested and the two different preparation methods were compared. For preparations on the Mass·Spec·Turbo Chip, 43 of 60 proteins were identified, whereas only 30 proteins were reliably identified after classical sample preparation. Comparison of the obtained Mascot scores, which reflect the confidence level of the protein identifications, revealed that for 70% of the identified proteins, higher scores were obtained by on-chip sample preparation. Typically, this gain was a consequence of higher sequence coverage due to increased sensitivity.     

Gel absorption-based sample preparation for the analysis of membrane proteome by mass spectrometry

A gel absorption-based sample preparation method for shotgun analysis of membrane proteome has been developed. In this new method, membrane proteins solubilized in a starting buffer containing a high concentration of sodium dodecyl sulfate (SDS) were directly entrapped and immobilized into gel matrix when the membrane protein solution was absorbed by the vacuum-dried polyacrylamide gel. After the detergent and other salts were removed by washing, the proteins were subjected to in-gel digestion and the tryptic peptides were extracted and analyzed by capillary liquid chromatography coupled with tandem mass spectrometry (CapLC-MS/MS). The results showed that the newly developed method not only avoided the protein loss and the adverse protein modifications during gel embedment but also improved the subsequent in-gel digestion and the recovery of tryptic peptides, particularly the hydrophobic peptides, thereby facilitating the identification of membrane proteins, especially the integral membrane proteins. Compared with the conventional tube-gel digestion method, the newly developed method increased the numbers of identified membrane proteins and integral membrane proteins by 25.0% and 30.2%, respectively, demonstrating that the method is of broad practicability in gel-based shotgun analysis of membrane proteome.     

Lipid raft proteomics: analysis of in-solution digest of sodium dodecyl sulfate-solubilized lipid raft proteins by liquid chromatography-matrix-assisted laser desorption/ionization tandem mass spectrometry

Lipid rafts are glycolipid- and cholesterol-enriched membrane microdomains implicated in membrane signaling and trafficking. The highly hydrophobic nature of lipid raft proteins pose significant problems of solubilization and recovery that hinder analysis by mass spectrometry (MS) and may under-report the composition of lipid rafts. In a previous investigation of the monocyte lipid raft in which proteins were digested with trypsin following polyacrylamide gel electrophoresis we identified 52 proteins. Here we report the development of a sodium dodecyl sulfate (SDS)-aided approach in which proteins are digested in solution and examined by high-performance liquid chromatography-matrix-assisted laser desorption/ionization-tandem mass spectrometry (HPLC-MALDI-MS/MS) using a novel LC-MALDI interface thereby circumventing the need to separate proteins on gels. Using this approach we identified 71 proteins in the lipid raft, 45 of which were not detected using in-gel digestion. Among the new proteins are alpha- and beta-tubulin, tubulinspecific chaperone A, a folding protein involved in tubulin dimer assembly, and KIF13, a microtubule motor protein indicating that proteins involved in microtubule assembly and trafficking are more readily detected using an in-solution approach. To investigate why tubulin was not identified by in-gel digestion, we compared the distribution of alpha-tubulin and the raft marker flotillin-2 in buoyant density gradients before and after separation on SDS-gels. Both proteins were present in the raft fractions, but tubulin was selectively lost following separation on SDS-gels. Assemblies of cytoskeletal proteins with lipid rafts may therefore be resolved using in-solution digestion that would be missed using gel-based approaches.     

Utility of electrophoretically derived protein mass estimates as additional constraints in proteome analysis of human serum based on MS/MS analysis

The proteome of a HUPO human serum reference sample was analyzed using multidimensional separation techniques at both the protein and the peptide levels. To eliminate false-positive identifications from the search results, we employed a data filtering method using molecular weight (MW) correlations derived from denaturing 1-DE. First, the six most abundant serum proteins were removed from the sample using immunoaffinity chromatography. 1-DE was then used to fractionate the remaining serum proteins according to the MW. Gel bands were isolated and in-gel digested with trypsin, and the resulting peptides were analyzed by 2-D LC/ESI-MS/MS. A SEQUEST search using the MS/MS results identified 494 proteins. Of these, 202 were excluded formally using protein data filtering as they were single-assignment proteins and their theoretical and electrophoretically-derived MWs did not correlate at high confidence. To evaluate this method, the results were compared with those of 1-D LC/MALDI-TOF/TOF and HUPO Plasma Proteome Project analyses. Our data filtering approach proved valuable in analysis of complex, large-scale proteomes such as human serum.     

Identification and quantification of differentially expressed proteins in E-cadherin deficient SCC9 cells and SCC9 transfectants expressing E-cadherin by dimethyl isotope labeling, LC-MALDI MS and MS/MS

A strategy based on isotope labeling of peptides and liquid chromatography matrix-assisted laser desorption ionization mass spectrometry (LC-MALDI MS) has been employed to accurately quantify and confidently identify differentially expressed proteins between an E-cadherin-deficient human carcinoma cell line (SCC9) and its transfectants expressing E-cadherin (SCC9-E). Proteins extracted from each cell line were tryptically digested and the resultant peptides were labeled individually with either d(0)- or d(2)-formaldehyde. The labeled peptides were combined and the peptide mixture was separated and fractionated by a strong cation exchange (SCX) column. Peptides from each SCX fraction were further separated by a microbore reversed-phase (RP) LC column. The effluents were then directly spotted onto a MALDI target using a heated droplet LC-MALDI interface. After mixing with a MALDI matrix, individual sample spots were analyzed by MALDI quadrupole time-of-flight MS, using an initial MS scan to quantify the dimethyl labeled peptide pairs. MS/MS analysis was then carried out on the peptide pairs having relative peak intensity changes of greater than 2-fold. The MS/MS spectra were subjected to database searching for protein identification. The search results were further confirmed by comparing the MS/MS spectra of the peptide pairs. Using this strategy, we detected and compared relative peak intensity changes of 5480 peptide pairs. Among them, 320 peptide pairs showed changes of greater than 2-fold. MS/MS analysis of these changing pairs led to the identification of 49 differentially expressed proteins between the parental SCC9 cells and SCC9-E transfectants. These proteins were determined to be involved in different pathways regulating cytoskeletal organization, cell adhesion, epithelial polarity, and cell proliferation. The changes in protein expression were consistent with increased cell-cell and cell-matrix adhesion and decreased proliferation in SCC9-E cells, in line with E-cadherin tumor suppressor activity. Finally, the accuracy of the MS quantification and subcellular localization for 6 differentially expressed proteins were validated by immunoblotting and immunofluorescence assays.     

Sample preparation issues for tissue imaging by imaging MS

Imaging MS is a powerful technique that combines the chemical and spatial analysis of surfaces. It allows spatial localization of multiple different compounds that are recorded in parallel without the need of a label. It is currently one of the rapidly developing techniques in the proteomics toolbox. Different complementary imaging MS methods, i.e. MALDI and secondary ion MS imaging for direct tissue analysis, can be applied on exactly the same tissue sample. This allows the identification of small molecules, peptides and proteins present on the same sample surface. Sample preparation is crucial to obtain high quality, reliable and reproducible complementary molecular images. It is essential to optimize the conditions for each step in the sample preparation protocol, ranging from sample collection and storage to surface modification. In this article, we review and discuss the importance of correct sample treatment in case of MALDI and secondary ion MS imaging experiments and describe the experimental requirements for optimal sample preparation.     

Proteomic analysis of Pinus radiata needles: 2-DE map and protein identification by LC/MS/MS and substitution-tolerant database searching

Pinus radiata is one of the most economically important forest tree species, with a worldwide production of around 370 million m (3) of wood per year. Current selection of elite trees to be used in conservation and breeding programes requires the physiological and molecular characterization of available populations. To identify key proteins related to tree growth, productivity and responses to environmental factors, a proteomic approach is being utilized. In this paper, we present the first report of the 2-DE protein reference map of physiologically mature P. radiata needles, as a basis for subsequent differential expression proteomic studies related to growth, development, biomass production and responses to stresses. After TCA/acetone protein extraction of needle tissue, 549 +/- 21 well-resolved spots were detected in Coommassie-stained gels within the 5-8 pH and 10-100 kDa M(r) ranges. The analytical and biological variance determined for 450 spots were of 31 and 42%, respectively. After LC/MS/MS analysis of in-gel tryptic digested spots, proteins were identified by using the novel Paragon algorithm that tolerates amino acid substitution in the first-pass search. It allowed the confident identification of 115 out of the 150 protein spots subjected to MS, quite unusual high percentage for a poor sequence database, as is the case of P. radiata. Proteins were classified into 12 or 18 groups based on their corresponding cell component or biological process/pathway categories, respectively. Carbohydrate metabolism and photosynthetic enzymes predominate in the 2-DE protein profile of P. radiata needles.     

Proteomic analysis of acrylamide gel separated proteins immobilized on polyvinylidene difluoride membranes following proteolytic digestion in the presence of 80% acetonitrile

Two-dimensional polyacrylamide gel electrophoresis (2-D PAGE) combined with mass spectrometry (MS) is a highly accurate and sensitive means of identifying proteins. We have developed a novel method for digesting proteins on polyvinylidene difluoride (PVDF) membranes for subsequent matrix-assisted laser desorption/ionization-time of flight (MALDI-TOF) MS analysis. After Tricine sodium dodecyl sulfate (SDS)-PAGE, separated proteins were electroblotted onto PVDF membranes in a semidry discontinuous buffer system, visualized by staining with Coomassie Blue, excised, digested with trypsin or lysC in 80% acetonitrile, and then analyzed by MALDI-TOF MS. This method has several advantages over in-gel digestion in terms of sample handling, sensitivity, and time. We identified 105 fmol of Bacillus subtilis SecA and 100 approximately 500 fmol of standard proteins. We also analyzed the submembrane protein fraction solubilized by 1% n-dodecyl-beta-D-maltoside from B. subtilis membranes after separation by 2-D PAGE, and identified 116 protein spots. This method can detect proteins at the 10 approximately 50 fmol level by pooling more than ten identical electroblotted protein spots.     

In-gel digestion for mass spectrometric characterization of proteins and proteomes

In-gel digestion of proteins isolated by gel electrophoresis is a cornerstone of mass spectrometry (MS)-driven proteomics. The 10-year-old recipe by Shevchenko et al. has been optimized to increase the speed and sensitivity of analysis. The protocol is for the in-gel digestion of both silver and Coomassie-stained protein spots or bands and can be followed by MALDI-MS or LC-MS/MS analysis to identify proteins at sensitivities better than a few femtomoles of protein starting material.