Flow injection chemiluminescence determination of isoniazid using the lucigenin-periodate system.

A weak chemiluminescence (CL) signal was observed during the mixing of isoniazid with lucigenin in alkaline aqueous solution. The CL signal was enhanced more than 100 times in the presence of potassium periodate. This CL system was developed for the determination of isoniazid using a flow injection mode. The CL intensity is proportional to the concentration of isoniazid in the range 0.005-1.0 mg/L. The limit of detection is 0.0034 mg/L and the relative standard deviation is 2.0% for 0.2 mg/L isoniazid solution in 11 repeated measurements. The method was applied to the determination of isoniazid in pharmaceutical preparations and satisfactory results were obtained.     

Investigation on the interaction between dihydroxybenzene and Fe3+- H2O2-Rh6G system based on enhancing chemiluminescence.

A highly sensitive flow-injection chemiluminescence (FI-CL) method has been developed for the determination of dihydroxybenzene, based on the hydroxyl radical reaction. Hydroxyl radical (.OH) produced by the reaction of Fe(3+) and H(2)O(2) oxidize rhodamine 6G to produce weak CL. It was observed that catechol and hydroquinone greatly enhanced the weak CL reaction. However, the proposed CL system is not suitable for determination of resorcinol because the enhancement reaction is very slow. The proposed procedure has a linear range of 0.01-2 mg/L for catechol, with a detection limit of 0.006 mg/L, and 0.008-1 mg/L for hydroquinone, with a detection limit of 0.004 mg/L. The possible mechanism of the CL system is discussed.     

Direct chemiluminescence determination of ibuprofen by the enhancement of the KMnO(4)-sulphite reaction.

A simple, rapid, flow-injection chemiluminescence (CL) method is described for the determination of ibuprofen. A strong CL signal was detected when a mixture of the analyte and sulphite was injected into acidic KMnO(4). The CL signal is proportional to the concentration of ibuprofen in the range 0.1-10.0 mg/L. The detection limit is 0.02 mg/L ibuprofen, the relative standard deviation is 1.8% (0.5 mg/L ibuprofen; n = 11) and the sample measurement frequency is 120/h. The proposed method was successfully applied to the determination of ibuprofen in pharmaceutical preparations and in spiked urine samples. The mechanism of the CL reaction is also discussed.     

Chemiluminescence flow-injection analysis of beta-lactam antibiotics using the luminol-permanganate reaction.

A new flow injection chemiluminescence (CL) method has been developed for the determination of six beta-lactam antibiotics, including amoxicillin, cefadroxil, cefoperazone sodium, cefazolin sodium, cefradine and ceftriaxone sodium. When the antibiotic was injected into a stream of KMnO4 with alkaline luminol, a strong CL signal was produced. The method allows the measurements of 0.1-50.0 mg/L amoxicillin, 0.1-80.0 mg/L cefadroxil, 1.0-30.0 mg/L cefoperazone sodium, 1.0-30.0 mg/L cefazolin sodium, 3.0-50.0 mg/L cefradine and 3.0-50.0 mg/L ceftriaxone sodium. The detection limits are 0.05 mg/L for amoxycillin, 0.05 mg/L for cefadroxil, 0.4 mg/L for cefoperazonum sodium, 0.4 mg/L for cefazolin sodium, 0.8 mg/L for cefradine and 0.8 mg/L for ceftriaxone sodium. The relative standard deviations in 11 repeated measurements are 0.6%, 0.8%, 1.5%, 1.2%, 0.4% and 0.3% for 3.0 mg/L amoxicillin, 1.0 mg/L cefadroxil, 10.0 mg/L cefoperazone sodium, 10.0 mg/L cefazolin sodium, 10.0 mg/L cefradine and 10.0 mg/L ceftriaxone sodium, respectively. The method was successfully applied to the determination of amoxicillin in pharmaceutical preparations. A possible CL reaction mechanism is also discussed.     

Post‐chemiluminescence determination of chloramphenicol based on luminol–potassium periodate system

A post‐chemiluminescence (PCL) phenomenon was observed when chloramphenicol was injected into a mixture of luminol and potassium periodate after the chemiluminescence (CL) reaction of luminol–potassium periodate had finished. The possible reaction mechanism was proposed based on studies of the CL kinetic characteristics, the CL spectra, the fluorescence spectra and the UV‐vis absorption spectra of the related substances. Based on the PCL reaction, a rapid and sensitive method for the determination of chloramphenicol was established. The linear response range was 6.0 × 10^?7–1.0 × 10^?5 mol/L, with a correlation coefficient of 0.9986. The relative standard deviation (RSD) for 5.0 × 10^?6 mol/L chloramphenicol was 2.3% (n = 11). The detection limit was 1.6 × 10^?7 mol/L. The method has been applied to the determination of chloramphenicol in pharmaceutical samples with satisfactory results. Copyright © 2011 John Wiley & Sons, Ltd.     

Inhibition of the system luminol-H2O2-Fe(CN)63− chemiluminescence by the Mn(II) indirect determination of isoniazid in a pharmaceutical formulation

A flow injection procedure for the indirect chemiluminescent determination of isoniazid is proposed. The method is performed in a flow-injection manifold provided with a solid-phase reactor. The reactor was made from manganese dioxide physically entrapped by polymerization; the redox reaction isoniazid–manganese dioxide released Mn(II) which was monitored through its inhibitory effect on the reaction between luminol and hydrogen peroxide in presence of potassium hexacyanoferrate(III). The procedure resulted in a linear calibration graph over the range 5–15 mg/L of isoniazid with a sample throughput of 43 samples/h. The influence of foreign compounds was studied and the method was applied to determination of the drug in a pharmaceutical formulation. © 1998 John Wiley & Sons, Ltd.     

Determination of ethanol using permanganate–CdS quantum dot chemiluminescence system

A novel and highly sensitive chemiluminescence (CL) method for the determination of ethanol was developed based on the CdS quantum dots (QDs)–permanganate system. It was found that KMnO₄ could directly oxidize CdS QDs in acidic media resulting in relatively high CL emission. A possible mechanism was proposed for this reaction based on UV/Vis absorption, fluorescence and the generated CL emission spectra. However, it was observed that ethanol had a remarkable inhibition effect on this system. This effect was exploited in the determination of ethanol within the concentration range 12–300 µg/L, with detection at 4.3 µg/L. In order to evaluate the capability of presented method, it was satisfactorily utilized in the determination of alcohol in real samples. Copyright © 2014 John Wiley & Sons, Ltd.     

Flow injection–chemiluminescence determination of acyclovir

The chemiluminescence (CL) reaction of acyclovir (ACV)–potassium permanganate, with formaldehyde as an enhancer, was investigated by the flow‐injection system, and a new method is reported for the determination of ACV on the basis of the reaction. The method is rapid, effective and simple for the determination of acyclovir in the range 0.2–80 mg/L, with a limit of detection of 0.06 mg/L (3 S:N), a relative standard deviation (RSD) of 3.7% for the determination of 1.0 mg/L acyclovir solution in 11 repeated measurements. The method has been applied to the determination of acyclovir in pharmaceuticals, with satisfactory results. The possible reaction mechanism is also discussed briefly. Copyright © 2011 John Wiley & Sons, Ltd.     

Chemiluminescence determination of fluoroquinolone antibiotics using a soluble manganese (IV)-sulphite system.

The reaction of soluble manganese (IV) with sulphite in acidic condition was found to elicit weak chemiluminescence (CL). The CL signal was remarkably enhanced in the presence of three fluoroquinolones, viz. norfloxacin, ofloxacin and ciprofloxacin. Based on these observations, a new flow-injection CL method was developed for the determination of these fluoroquinolones. The method allows determination in the range 5.0 x 10(-8)-1.0 x 10(-6) mol/L for norfloxacin, 1.0 x 10(-7)-8.0 x 10(-6) mol/L for ofloxacin and 1.0 x 10(-7)-3.0 x 10(-5) mol/L for ciprofloxacin, with detection limits of 3 x 10(-8) mol/L, 5 x 10(-8) mol/L and 3 x 10(-8) mol/L, respectively. The method was applied to the determination of fluoroquinolones in pharmaceutical preparations.     

Determination of bisphenol A using a flow injection inhibitory chemiluminescence method.

A new flow injection chemiluminescence (CL) method has been developed for the determination of bisphenol A (BPA), based on the inhibitory effect of BPA on the chemiluminescence reaction between luminol and potassium hexacyanoferrate. Under optimum conditions, the decrease in CL emission intensity was linear with BPA concentration in the range 8.0 x 10(-7)-1.2 x 10(-5) mol/L, and the detection limit was 3.1 x 10(-7) mol/L. The relative standard deviation (RSD) of 11 replicate measurements was 2.6% for 2.0 x 10(-6) mol/L BPA (n = 11). The sampling frequency was calculated to be ca. 120/h. This method has been successfully used to determine the content of BPA in aqueous solution of polycarbonate materials. A brief discussion on the possible chemiluminescence reaction mechanism is presented.     

Determination of tsumacide residues in vegetable samples using a flow-injection chemiluminescence method.

A sensitive, simple and rapid flow-injection chemiluminescence (FI-CL) method is described to determine tsumacide pesticide residue based on the CL reaction of the alkaline degradation product of tsumacide with acidic KMnO(4) when rhodamine 6G was present. Under the optimum conditions, the relative CL intensity is linear with the concentration of tsumacide in the range of 2.0 x 10(-3)-0.20 mg/L. The detection limit is 6.6 x 10(-4) mg/L (3sigma) and the relative standard deviation for 2.0 x 10(-2) mg/L tsumacide solution was 2.28% (intra-day) and 4.85% (inter-day). The proposed method has been applied to determine the residue of tsumacide in vegetable samples and the recovery test is very satisfactory.     

Determination of parathion residues in rice samples using a flow injection chemiluminescence method

A sensitive ?ow injection chemiluminescence method is described for the determination of parathion pesticide, based upon its direct chemiluminescence reaction with luminol and hydrogen peroxide in the presence of non‐ionic surfactant polyethylene glycol 400. Under the selected experimental conditions, the concentration of parathion is proportional to the CL intensity in the range 0.02–1.0 mg/L. The detection limit was 0.008 mg/L and the relative standard deviation was 2.8% for 0.2 mg/L parathion solution (n = 11). This method was successfully applied to the determination of parathion residue in rice samples. Copyright © 2003 John Wiley & Sons, Ltd.     

CdS nanoparticles‐ enhanced chemiluminescence and determination of baicalin in pharmaceutical preparations

CdS nanoparticles (CdS NPs) of different sizes were synthesized by the citrate reduction method. It was found that CdS NPs could enhance the chemiluminescence (CL) of the luminol‐potassium ferricyanide system and baicalin could inhibit CdS NPs‐enhanced luminol‐potassium ferricyanide CL signals in alkaline solution. Based on this inhibition, a flow‐injection CL method was established for determination of baicalin in pharmaceutical preparations and human urine samples. Under optimized conditions, the linear range for determination of baicalin was 5.0 x 10^?6 to 1.0 x 10^?3 g/L. The detection limit at a signal‐to‐noise ratio of 3 was 1.7 x 10 ^?6 g/L. CL spectra, UV‐visible spectra and transmission electron microscopy (TEM) were used to investigate the CL mechanism. The method described is simple, selective and obviates the need of extensive sample pretreatment. Copyright © 2012 John Wiley & Sons, Ltd.     

Sensitive determination of epinephrine in pharmaceutical preparation by flow injection coupled with chemiluminescence detection and mechanism study

A novel, rapid and sensitive method was described for the determination of epinephrine (EP) using flow injection analysis coupled with chemiluminescence (CL) detection, which based on EP enhanced the weak CL emission of luminol–KIO₄ system in NaOH solution. Parameters affecting the CL intensity and reproducibility were optimized systematically. Under the optimized experiment conditions, the net CL intensity was proportional to the concentration of EP in the range of 5.0 × 10^?8 to 1.5 × 10^?6 mol/L with a detection limit of 1.9 × 10^?9 mol/L. The relative standard deviation (RSD) was found to be 0.7% for 13 replicate determinations of 3.0 × 10^?7 mol/L EP. The applicability of the proposed method was illustrated in the determination of EP in pharmaceutical preparation. The recoveries of EP at different levels in EP hydrochloride injection were between 95.4 and 104.7%. One assay procedure takes only 27 s, and the sampling rate was calculated about to be 130 samples/h. The possible mechanism of the enhanced CL intensity was studied by examining CL spectra and UV–vis spectra. Copyright © 2009 John Wiley & Sons, Ltd.     

Determination of iron in blood serum using flow injection with luminol chemiluminescence detection.

A simple and rapid fl ow injection method is reported for the determination of iron in blood serum after acid digestion with HNO3 and HClO4, based on luminol CL detection in the absence of added oxidant. The detection limit (3 s) was 1.0 nmol/L with a sample throughput of 120/h. The calibration graph was linear over the range 0.001-1.0 micromol/L (r2 = 0.9974), with relative standard deviations (RSD) (n = 4) in the range 3.2-5%. The effect of interfering cations (Ca(II), Mg(II), Cu(II), Cd(II), Pb(II), Mn(II), Zn(II), Ni(II), Co(II) and Fe(III)) and anions (Cl-, SO4(2-), HCO3-, NO3-, NO2-) were studied using a luminol CL system for Fe(II) determination. The method was applied to normal blood serum and the results (1.32 +/- 0.08-1.74 +/- 0.05 mg/L) were compared with those from a spectrophotometric reference method (1.34 +/- 0.06-1.80 +/- 0.10 mg/L), which agree fairly well with the overall reference range in blood.     

Sensitive determination of synephrine by flow-injection chemiluminescence.

It was found that light emission produced by the oxidation of luminol by potassium ferricyanide in basic medium was enhanced by synephrine, an anti-obesity drug. The optimum conditions for this chemiluminescent reaction were studied in detail in a flow injection system and employed in a new, simple and rapid method for the determination of synephrine. A mechanism for this reaction is proposed, based on the chemiluminescence reaction spectra. In the optimum conditions, CL intensity is proportional to concentration of synephrine in the 0.008-1 microg/mL range. The limit of detection is 1.6 ng/mL for synephrine (3sigma), and the relative standard deviation (n = 11) is 2.6% for 0.5 microg/mL synephrine. The method was applied to the determination of synephrine in herbal products, citrus fruit and biological fluids. The recoveries were satisfactory (90-102%). The results given by the proposed method are in good agreement with those given by HPLC-UV.     

Flow‐injection chemiluminescence method for the determination of chloramphenicol based on luminol–sodium periodate order‐transform second‐chemiluminescence reaction

A new chemiluminescence (CL) reaction was observed when chloramphenicol solution was injected into the mixture after the end of the reaction of alkaline luminol and sodium periodate or sodium periodate was injected into the reaction mixture of chloramphenicol and alkaline luminol. This reaction is described as an order‐transform second‐chemiluminescence (OTSCL) reaction. The OTSCL method combined with a flow‐injection technique was applied to the determination of chloramphenicol. The optimum conditions for the order‐transform second‐chemiluminescence emission were investigated. A mechanism for OTSCL has been proposed on the basis of the chemiluminescence kinetic characteristics, the UV‐visible spectra and the chemiluminescent spectra. Under optimal experimental conditions, the CL response is proportional to the concentration of chloramphenicol over the range 5.0 × 10^?7–5.0 × 10^?5 mol/L with a correlation coefficient of 0.9969 and a detection limit of 6.0 × 10^?8 mol/L (3σ). The relative standard deviation (RSD) for 11 repeated determinations of 5.0 × 10^?6 mol/L chloramphenicol is 1.7%. The method has been applied to the determination of chloramphenicol in pharmaceutical samples with satisfactory results. Copyright © 2011 John Wiley & Sons, Ltd.     

Flow-injection chemiluminescence determination of catecholamines based on their enhancing effects on the luminol-potassium periodate system.

A rapid and sensitive chemiluminescence (CL) method using flow injection analysis is described for the determination of four catecholamines, dopamine, adrenaline, isoprenaline and noradrenaline, based on their greatly enhancing effects on the CL reaction of luminol-potassium periodate in basic solutions. The optimized chemical conditions for the chemiluminescence reaction were 1.0 x 10(-4) mol/L luminol and 1.0 x 10(-5) mol/L potassium periodate in 0.2 mol/L sodium hydroxide (NaOH). Under the optimized conditions, the calibration graphs relating the CL signal intensity (peak height) to the concentration of the analytes were curvilinear and they were suitable for determining dopamine, adrenaline, isoprenaline, and noradrenaline in the range 0.1-10 ng/mL, 0.1-100 ng/mL, 1-100 ng/mL and 5-50 ng/mL, respectively, with the relative standard deviations of 0.8-1.7%. The detection limits of the method are 0.02 ng/mL for dopamine, 0.01 ng/mL for adrenaline, 0.1 ng/mL for isoprenaline and 2.0 ng/mL for noradrenaline. The sampling frequency was calculated to be about 60/h. The selectivity of the method was good, because a series of common ions or excipients, such as K(+), Ba(2+), CO(3)(2-), NO(3)(-), SO(4)(2-), PO(4)(3-), sodium citrate, sodium bisulphite, oxidate dopamine, starch, lactose, carbamide and gelatin, could not produce interference when their concentrations were 1000-fold than those of dopamine. The present method was successfully applied to the determination of the four catecholamines in pharmaceutical injections.     

A sensitive inhibition chemiluminescence method for the determination of trace tannic acid using the reaction of luminol-hydrogen peroxide catalysed by tetrasulphonated manganese phthalocyanine.

A novel CL method for the determination of tannic acid (TA) was established based on TA inhibition of the chemiluminescence (CL) emission of the luminol-hydrogen peroxide CL system catalysed by tetrasulphonated manganese phthalocyanine (MnTSPc) under alkaline conditions. The peak height is proportional to the natural logarithm of concentration of TA in the range 1.0 x 10(-7)-3.0 x 10(-10) mol/L with a detection limit of 5.6 x 10(-11) mol/L and the relative standard deviation was 2.5% for the determination of 1.0 x 10(-8) mol/L TA (n = 11). The proposed method has been successfully applied to the determination of TA in Chinese gall and industrial wastewater.     

Determination of thyroxine in pharmaceuticals using flow injection with luminol chemiluminescence inhibition detection.

A simple flow injection method is reported for the determination of thyroxine, based on its inhibition effect on luminol-iron(II) chemiluminescence in alkaline medium in the presence of molecular oxygen. The detection limits (2s) for d- and l-thyroxine are 0.08 and 0.1 mg/L, respectively, with a sample throughput of 100/h. The calibration data for d- and l-thyroxine over the range 0.2-1.0 mg/L gives correlation coefficients (r(2)) of 0.9915 and 0.984 with relative standard deviations (RSD; n = 4) in the range 1.2-2.8%. The effects of some organic compounds was studied on luminol-iron(II) CL system for thyroxine determination. The method was applied to pharmaceutical thyroxine tablets and the results obtained (in the range 50.5 +/- 2.0-51.6 +/- 1.2 microg l-thyroxine/tablet) were in reasonable agreement with the value quoted.