Measuring adsorption of a hydrophobic probe with a surface plasmon resonance sensor to monitor conformational changes in immobilized proteins

Conformational changes of proteins immobilized on solid matrices were observed by measuring the adsorption of Triton X-100 (TX), a nonionic detergent, as a hydrophobic probe with BIACORE, a biosensor that utilizes the phenomenon of surface plasmon resonance (SPR). Two kinds of proteins, alpha-glucosidase and lysozyme, were covalently attached to dextran matrices on the sensor surface in the flow cell and then exposed to various concentrations of TX solution. We measured SPR signal changes derived from adsorption of TX to the immobilized proteins and calculated the monolayer adsorption capacity using the Brunauer-Emmett-Teller (BET) equation. The results demonstrated that monolayer adsorption capacity is proportional to the amount of immobilized proteins. Further, the unfolding process of immobilized proteins on the sensor surface induced by guanidine hydrochloride was investigated by monitoring SPR signal increases due to the adsorption of TX to the exposed hydrophobic region of the protein. Results strongly suggested that the increase in the SPR signal reflected the formation of the agglutinative unfolded state. We expect our measuring method using the SPR sensor and TX adsorption will be a novel tool to provide conformational information regarding various proteins on solid matrices.     

Label-free reading of microarray-based proteins with high throughput surface plasmon resonance imaging

A simple method is presented discriminating proteins at a gold surface by using an emerging technology, surface plasmon resonance (SPR) imaging. As a high throughput method, the protein array of bovine serum albumin (BSA), poly-l-lysine (PL), casein and lactate dehydrogenase (LDG) was fabricated and SPR imaging enables detection from different kinds of proteins immobilized on the sensor surface. These proteins can be discriminated directly by various reflected intensity or changing the incident angular position of light. Denaturation of these immobilized proteins on SPR sensor by interacting with denaturant 6M GdnHCl solution was also performed and obvious changes in reflected intensity were occurred after denaturation. The observation of denaturation of these proteins further supported the fact that different proteins could be discriminated on protein array before denaturation. On the other hand, the procedure of denaturation provided useful information that any change of molecular structure with the progress of denaturation would result in change of SPR signal. Excellent reproducibility with a chip-to-chip for label-free discriminating various proteins was achieved.     

Monitoring of the refolding process for immobilized firefly luciferase with a biosensor based on surface plasmon resonance

In order to examine the possibility of the use of a surface plasmon resonance (SPR) sensor for real-time monitoring of the process of refolding of immobilized proteins, the refolding of firefly luciferase immobilized on a carboxymethyldextran matrix layer was analyzed. The SPR signal of the immobilized luciferase decreased after unfolding induced by GdnCl and increased gradually in the refolding buffer, while there was no signal change in the reference surface lacking the immobilized protein. The decrease in the SPR signal on unfolding was consistent with the difference between the refractive indices of the native and unfolded protein solutions. The effects of blocking of the excess NHS-groups of the matrix layer on the refolding yield were examined by means of an SPR sensor. The results were consistent with those obtained with the enzymatic activity assay, indicating that the changes in the SPR signal reflected the real-time conformational changes of the immobilized protein. Hence, an SPR biosensor might be used for monitoring of the process of refolding of immobilized proteins and as a novel tool for optimization of the refolding conditions. This is the first demonstration that SPR signal changes reflect the conformational changes of an immobilized protein upon unfolding and refolding.     

Binding and signaling of surface-immobilized reagentless fluorescent biosensors derived from periplasmic binding proteins

Development of biosensor devices typically requires incorporation of the molecular recognition element into a solid surface for interfacing with a signal detector. One approach is to immobilize the signal transducing protein directly on a solid surface. Here we compare the effects of two direct immobilization methods on ligand binding, kinetics, and signal transduction of reagentless fluorescent biosensors based on engineered periplasmic binding proteins. We used thermostable ribose and glucose binding proteins cloned from Thermoanaerobacter tengcongensis and Thermotoga maritima, respectively. To test the behavior of these proteins in semispecifically oriented layers, we covalently modified lysine residues with biotin or sulfhydryl functions, and attached the conjugates to plastic surfaces derivatized with streptavidin or maleimide, respectively. The immobilized proteins retained ligand binding and signal transduction but with adversely affected affinities and signal amplitudes for the thiolated, but not the biotinylated, proteins. We also immobilized these proteins in a more specifically oriented layer to maleimide-derivatized plates using a His(2)Cys(2) zinc finger domain fused at either their N or C termini. Proteins immobilized this way either retained, or displayed enhanced, ligand affinity and signal amplitude. In all cases tested ligand binding by immobilized proteins is reversible, as demonstrated by several iterations of ligand loading and elution. The kinetics of ligand exchange with the immobilized proteins are on the order of seconds.     

Real-time monitoring of cell-free protein synthesis on a surface plasmon resonance chip

Taking advantage of the "open" nature of cell-free protein synthesis, this study investigated the direct analysis of protein expression using a surface plasmon resonance sensor. During the on-chip incubation of the reaction mixture for cell-free protein synthesis, the expressed protein molecules were immobilized onto the surface of the chip, giving rise to a sensorgram signal, which enabled on-line monitoring of protein expression. In addition, we found that the expression of the aggregation-prone proteins could be effectively monitored. The ability to monitor these proteins was most likely through the instant isolation of the expressed protein molecules onto the solid surface of the chip.     

Evaluation of surface hydrophobicity of immobilized protein with a surface plasmon resonance sensor

Immobilization is widely used to isolate agglutinative and associative proteins with large hydrophobic surfaces. Surface hydrophobicities of immobilized proteins were quantified by measuring the adsorption amounts of Triton X-100 as a hydrophobic probe with a biosensor that utilizes the phenomena of surface plasmon resonance (SPR). We measured SPR signal changes derived from adsorption of Triton X-100 to five kinds proteins and calculated the monolayer adsorption capacity using the Brunauer-Emmett-Teller equation, partly modified with a term for correcting an influence of the net charge of immobilized protein. SPR signal changes obtained by this method correlated with the values of surface hydrophobicities obtained by conventional assay using a hydrophobic probe. Thus this measuring method using an SPR sensor and Triton X-100 is expected to be a tool for quantifying surface hydrophobicities of immobilized proteins.     

High-performance analytical applications of immobilized metal ion affinity chromatography

The separation of three sets of standard protein mixtures on a high-performance immobilized metal ion affinity chromatography (HP-IMAC) column by elution with linear gradients of imidazole is described. The affinity of the test proteins for the immobilized metal ions follows the order Cu2+ greater than Ni2+ greater than Zn2+. The iminodiacetic acid-Cu2+ column gives the best resolution of all three protein mixtures and is the only immobilized metal ion column that can be used for elution of absorbed proteins with a decreasing pH gradient. An application of HP-IMAC for the separation of monoclonal IgG from mouse ascites fluid is also outlined. This versatile separation method is thus suitable for both analytical and preparative separations of proteins and peptides resulting in high recoveries and good reproducibility. The leakage of immobilized metal ions from the TSK gel chelate-5PW is apparent if the column is eluted by buffers containing low concentrations of (i) glycine or (ii) primary amines at round neutral pH. Considerable amounts of immobilized Zn2+ and Ni2+ ions also leak from the column by washing with buffers of pH 4.5 or lower. However, all three immobilized metal ions are stable toward exposure to low concentrations of imidazole (up to 50 mM) in phosphate buffers between pH 6.5 and 8.0. Adsorbed proteins could thus be eluted conveniently by using linear gradients of imidazole to give reproducible results. Moreover, this elution procedure made it possible to use the IMAC columns for repeated runs without the need for regeneration and recharging of the columns with fresh metal ions after each use.     

Estrogen conjugation and antibody binding interactions in surface plasmon resonance biosensing

Thioether-linked 3-mercaptopropionic acid derivatives of 17beta-estradiol and estrone were formed at the A-ring 4-position of the steroids by substitution of their 4-bromo analogues. The carboxylic acid terminal was used to link to an oligoethylene glycol (OEG) chain of 15-atoms in length. The OEG derivative of 17beta-estradiol was then in situ immobilized on a carboxymethylated dextran-coated gold sensor surface used to detect refractive index changes upon protein binding to the surface by surface plasmon propagation in a BIAcore surface plasmon resonance (SPR) instrument. Two other estradiol-OEG derivatives with Mannich reaction linkage at the 2-position and hemisuccinate linkage at the 3-position were also immobilized on the sensor surfaces for comparison. Binding performance between these immobilized different positional conjugates and monoclonal anti-estradiol antibody, raised from a 6-position conjugate, clearly demonstrated that both 2- and 4-conjugates, not conjugated through existing functional groups, gave strong antibody bindings, whereas the 3-conjugate through an existing functional group (3-OH) gave very little binding (2% compared to the 2-conjugate). Both 2- and 4-position conjugates were then applied in a highly sensitive estradiol SPR immunoassay with secondary antibody mediated signal enhancement that gave up to a 9.5-fold signal enhancement of primary antibody binding, and a detection limit of 25 pg/mL was achieved for a rapid and convenient flow-through immunoassay of estradiol.     

Complement protein C1q recognizes a conformationally modified form of the prion protein

Several studies have suggested the implication of the classical complement pathway in the early stages of prion disease pathogenesis. To explore this hypothesis, surface plasmon resonance spectroscopy was used to test the ability of human C1q to recognize mouse PrP immobilized on a sensor chip. In this configuration, C1q bound avidly to PrP, with a K(D) of 5.4 nM (k(on) = 2.4 x 10(5) M(-1) s(-1); k(off) = 1.3 x 10(-3) s(-1)). The isolated C1q globular domain also bound to immobilized PrP, although with a higher K(D) (238 nM), due to a decreased k(on) (4.2 x 10(3) M(-1) s(-1)). Interaction was strongly enhanced by Cu(2+) ions, with a 10-fold increase in overall binding in the presence of 10 microM CuSO(4), without significant modification of the kinetic parameters. In contrast, using the same technique, no interaction was detected between immobilized C1q and soluble PrP. Likewise, gel filtration and chemical cross-linking analyses yielded no evidence for an interaction between these proteins in solution. Comparative analysis of the antigenic reactivity of soluble and immobilized PrP was performed by ELISA and surface plasmon resonance spectroscopy, respectively, using anti-PrP monoclonal antibodies. This analysis provides evidence that immobilized PrP undergoes a major conformational change in the sequence stretch 141GNDWEDRYYRENMYRYPNQ159 located in its C-terminal globular domain. It is concluded that immobilized PrP undergoes structural modifications that possibly mimic the conformational changes occurring during conversion to the pathological isoform and that C1q represents a natural sensor of these changes. Pathological implications of this recognition property are discussed in light of recent reports.     

Cytometry on a chip: cellular phenotypic and functional analysis using grating-coupled surface plasmon resonance

Grating-coupled surface plasmon resonance imaging (GCSPRI) is a method for the accurate assessment of both cell phenotype and function. In GCSPRI, cells and/or proteins of interest are flowed across antibodies immobilized on a gold-coated sensor chip. The surface of the chip is illuminated with monochromatic light that couples with surface plasmons in the gold. At a specific angle of incidence, the GCSPR angle, the maximum amount of coupling occurs. Shifts in the GCSPR angle can be correlated with refractive index changes following cell or analyte capture by the immobilized antibodies. In addition, GCSPRI can image the cells as they are being captured. GCSPRI's multiplexed format allows for the parallel assessment of up to 400 individual antibody regions. In this paper, we demonstrate GCSPRI's ability to identify cells and proteins of interest and compare results to a traditional flow cytometry system. This technology represents a fast and powerful method for the simultaneous assessment of cell phenotype and function.     

Phage immobilized magnetoelastic sensor for the detection of Salmonella typhimurium

In this article, a phage-based magnetoelastic sensor for the detection of Salmonella typhimurium is reported. Filamentous bacteriophage specific to S. typhimurium was used as a biorecognition element in order to ensure specific and selective binding of bacteria onto the sensor surface. Phage was immobilized onto the surface of the sensors by physical adsorption. The phage immobilized magnetoelastic sensors were exposed to S. typhimurium cultures with different concentrations ranging from 5x10(1) to 5x10(8) cfu/ml, and the corresponding changes in resonance frequency response of the sensor were studied. It was experimentally established that the sensitivity of the magnetoelastic sensors was higher for sensors with smaller physical dimensions. An increase in sensitivity from 159 Hz/decade for a 2 mm sensor to 770 Hz/decade for a 1 mm sensor was observed. Scanning electron microscopy (SEM) analysis of previously assayed biosensors provided visual verification of frequency changes that were caused by S. typhimurium binding to phage immobilized on the sensor surface. The detection limit on the order of 10(3) cfu/ml was obtained for a sensor with dimensions 1x0.2x0.015 mm.     

Cell surface analysis techniques: What do cell preparation protocols do to cell surface properties?

Cell surface analysis often requires manipulation of cells prior to examination. The most commonly employed procedures are centrifugation at different speeds, changes of media during washing or final resuspension, desiccation (either air drying for contact angle measurements or freeze-drying for sensitive spectroscopic analysis, such as X-ray photoelectron spectroscopy), and contact with hydrocarbon (hydrophobicity assays). The effects of these procedures on electrophoretic mobility, adhesion to solid substrata, affinity to a number of Sepharose columns, structural integrity, and cell viability were systematically investigated for a range of model organisms, including carbon- and nitrogen-limited Psychrobacter sp. strain SW8 (glycocalyx-bearing cells), Escherichia coli (gram-negative cells without a glycocalyx), and Staphylococcus epidermidis (gram-positive cells without a glycocalyx). All of the cell manipulation procedures severely modified the physicochemical properties of cells, but with each procedure some organisms were more susceptible than others. Considerable disruption of cell surfaces occurred when organisms were placed in contact with a hydrocarbon (hexadecane). The majority of cells became nonculturable after air drying and freeze-drying. Centrifugation at a high speed (15,000 x g) modified many cell surface parameters significantly, although cell viability was considerably affected only in E. coli. The type of washing or resuspension medium had a strong influence on the values of cell surface parameters, particularly when high-salt solutions were compared with low-salt buffers. The values for parameters obtained with different methods that allegedly measure similar cell surface properties did not correlate for most cells. These results demonstrate that the methods used to prepare cells for cell surface analysis need to be critically investigated for each microorganism so that the final results obtained reflect the nature of the in situ microbial cell surface as closely as possible. There is an urgent need for new, reliable, nondestructive, minimally manipulative cell surface analysis techniques that can be used in situ.     

Protein microarrays to study carbohydrate-recognition events

In order to expand areas in which protein microarrays can be used to solve important biological problems, we have investigated ways in which the technique can be employed for functional glycomics. Initially, our protein microarrays were used for the rapid identification of carbohydrate-binding proteins using trifunctional carbohydrate probes and fluorescent dye-labeled polysaccharides. Glycan probes were selectively bound to the corresponding lectins immobilized on the solid surface. In addition, these microarrays were also employed for profiling of carbohydrates on Jurkat T-cell surfaces. These cells adhered to ConA, RCA(120), SNA and WGA, indicating expression of alpha-Man, Gal, NeuNAcalpha2,6Gal and GlcNAc residues on their surfaces. Furthermore, we determined binding affinities between WGA and carbohydrates by measuring IC(50) values of GlcNAc that inhibited 50% of trivalent GlcNAc binding to WGA immobilized on the solid surface. All the experiments show that protein microarrays can be used to study carbohydrate-recognition events in the field of glycomics.     

Protein-heparin interactions measured by BIAcore 2000 are affected by the method of heparin immobilization

Surface plasmon resonance (SPR) biosensors such as the BIAcore 2000 are a useful tool for the analysis of protein-heparin interactions. Generally, biotinylated heparin is captured on a streptavidin-coated surface to create heparinized surfaces for subsequent binding analyses. In this study we investigated three commonly used techniques for the biotinylation of heparin, namely coupling through either carboxylate groups or unsubstituted amines along the heparin chain, or through the reducing terminus of the heparin chain. Biotinylated heparin derivatives were immobilized on streptavidin sensor chips and several heparin-binding proteins were examined. Of the surfaces investigated, heparin attached through the reducing terminus had the highest binding capacity, and in some cases had a higher affinity for the proteins tested. Heparin immobilized via intrachain bare amines had intermediate binding capacity and affinity, and heparin immobilized through the carboxylate groups of uronic acids had the lowest capacity for the proteins tested. These results suggest that immobilizing heparin to a surface via intrachain modifications of the heparin molecule can affect the binding of particular heparin-binding proteins.     

Surface plasmon resonance-based detection of ladder-shaped polyethers by inhibition detection method

Ladder-shaped polyether (LSP) compounds represented by brevetoxins and ciguatoxins were largely discovered in association with seafood poisoning. Thus, a quick quantification method for LSPs is potentially important. We examined a surface plasmon resonance method using desulfated-yessotoxin (dsYTX) immobilized on a sensor chip and phosphodiesterase PDEII in a inhibition detection mode. Yessotoxin, brevetoxin B and synthetic LSP derivatives showed clear inhibition against PDEII binding to the immobilized dsYTX, by which their half inhibitory concentrations were successfully estimated. This inhibition method appeared to be superior in specificity to direct binding assays where binding proteins to LSP was immobilized on a sensor chip.     

Induction of Salivary Proteins Modifies Measures of Both Orosensory and Postingestive Feedback during Exposure to a Tannic Acid Diet

There are hundreds of proteins in saliva. Although it has long been hypothesized that these proteins modulate taste by interacting with taste receptors or taste stimuli, the functional impact of these proteins on feeding remains relatively unexplored. We have developed a new technique for saliva collection that does not interfere with daily behavioral testing and allows us to explore the relationship between feeding behavior and salivary protein expression. First, we monitored the alterations in salivary protein expression while simultaneously monitoring the animals'' feeding behavior and meal patterns on a custom control diet or on the same diet mixed with 3% tannic acid. We demonstrated that six protein bands increased in density with dietary tannic acid exposure. Several of these bands were significantly correlated with behaviors thought to represent both orosensory and postingestive signaling. In a follow-up experiment, unconditioned licking to 0.01–3% tannic acid solutions was measured during a brief-access taste test before and after exposure to the tannic acid diet. In this experiment, rats with salivary proteins upregulated found the tannin solution less aversive (i.e., licked more) than those in the control condition. These data suggest a role for salivary proteins in mediating changes in both orosensory and postingestive feedback.     

Quantification of surface etching by common buffers and implications on the accuracy of label-free biological assays

High throughput analyses in biochemical assays are gaining popularity in the post-genomic era. Multiple label-free detection methods are especially of interest, as they allow quantitative monitoring of biomolecular interactions. It is assumed that the sensor surface is stable to the surrounding medium while the biochemical processes are taking place. Using the Interferometric Reflectance Imaging Sensor (IRIS), we found that buffers commonly used in biochemical reactions can remove silicon dioxide, a material frequently used as the solid support in the microarray industry. Here, we report 53 pm to 731 pm etching of the surface silicon oxide over a 12-h period for several different buffers, including various concentrations of SSC, SSPE, PBS, TRIS, MES, sodium phosphate, and potassium phosphate buffers, and found that PBS and MES buffers are much more benign than the others. We observe a linear dependence of the etch depth over time, and we find the etch rate of silicon dioxide in different buffers that ranges from 2.73±0.76 pm/h in 1M NaCl to 43.54±2.95 pm/h in 6×SSC. The protective effects by chemical modifications of the surface are explored. We demonstrate unaccounted glass etching leading to erroneous results with label-free detection of DNA microarrays, and offer remedies to increase the accuracy of quantitative analysis.     

Langmuir and Langmuir-Blodgett films of organophosphorus acid anhydrolase

In this paper, we describe the preparation and characterization of Langmuir and Langmuir-Blodgett (LB) monolayers of the enzyme organophosphorus acid anhydrolase (OPAA). Langmuir films of OPAA were characterized on different subphases, such as phosphate, ammonium carbonate, and bis-tris-propane buffers. Monolayers at the air-water interface were characterized by measuring the surface pressure and surface potential-area isotherms. In situ UV-vis absorption spectra were also recorded from the Langmuir monolayers. The enzyme activity at the air-water interface was tested by the addition of diisopropylfluorophosphate (DFP) to the subphase. LB films of OPAA were transferred to mica substrates to be studied by atomic force microscopy. Finally, a one-layer LB film of OPAA labeled with a fluorescent probe, fluorescein isothiocyanate (FITC), was deposited onto a quartz slide to be tested as sensor for DFP. The clear, pronounced response and the stability of the LB film as a DFP sensor show the potential of this system as a biosensor.     

Controlled antibody immobilization onto immunoanalytical platforms by synthetic peptide

Antibody immobilization on a solid surface is inevitable in the preparation of immunochips/sensors. Antibody-binding proteins such as proteins A and G have been extensively employed to capture antibodies on sensor surfaces with right orientations, maintaining their full functionality. Because of their synthetic versatility and stability, in general, small molecules have more advantages than proteins. Nevertheless, no small molecule has been used for oriented and specific antibody immobilization. Here is described a novel strategy to immobilize an antibody on various sensor surfaces by using a small antibody-binding peptide. The peptide binds specifically to the Fc domain of immunoglobulin G (IgG) and, therefore, affords a properly oriented antibody surface. Surface plasmon resonance analysis indicated that a peptide linked to a gold chip surface through a hydrophilic linker efficiently captured human and rabbit IgGs. Moreover, antibodies captured by the peptide exhibited higher antigen binding capacity compared with randomly immobilized antibodies. Peptide-mediated antibody immobilization was successfully applied on the surfaces of biosensor substrates such as magnetic particles and glass slides. The antibody-binding peptide conjugate introduced in this work is the first small molecule linker that offers a highly stable and specific surface platform for antibody immobilization in immunoassays.     

Biosensor-based evaluation of liposomal behavior in the target binding process

In this study we evaluated the quartz crystal microbalance (QCM) as a biosensor for a real-time investigation of liposomal binding, under dynamic flow conditions, onto target proteins immobilized at the sensor. The mass-sensitive frequency changes of quartz sensors allow for a quantification of the liposomal binding process. Furthermore, simultaneous damping analysis gives an insight into liposomal behavior, such as the degree of liposomal deformation or spreading at the target surface. In this study a series of liposomes was evaluated, differing in the kind and concentration of ligands interacting with appropriate target proteins. It became evident that an increase in homing device concentration accelerated deformation and flattening of liposomes, triggering a fusion process. Furthermore, liposomal deformation corresponded with the binding affinity of target molecules, comparing biotin/avidin with E-selectin/ligand interactions. Deformation could be emphasized using dioleoylphosphatidylethanolamine (DOPE) as a fusiogenic membrane component, while sterical stabilization by polyethylenglycol (PEG-PE) appeared in a low degree of deformation. Consequently, the online detection of liposomal target binding by QCM is an excellent facility to control and predict the liposomal behavior at the target site for increasing therapeutic potency.