An electrochemical method of measuring the oxidation rate of ferrous to ferric iron with oxygen in the presence of Thiobacillus ferrooxidans

The oxidation of Fe(2+) with oxygen in sulfate solutions was studied in the presence of T. ferrooxidans. To measure the chemical activity of bacteria, and the oxidation rate of iron, the redox potentials of solutions were continuously monitored during the experiments. The redox potentials were simultaneously monitored on the platinum and pyrite indicator electrodes. The redox potential versus time curves were further used to calculate the basic kinetic parameters, such as the reaction orders, the activation energy, and the frequency factor. It was found that under atmospheric conditions, and at Fe(2+) < 0.001M, T < 25 degrees C, and at pH above 2.2, the oxidation of iron is governed by the following rate expression: \documentclass{article}\pagestyle{empty}\begin{document}$$ - \frac{{d[{\rm Fe};{2 + }]}}{{dt}} = 1.62 \times 10;{11} C_{{\rm bact}} [{\rm H}; + ][{\rm Fe};{2 + }]p{\rm O}_2 e;{ - (58.77/RT)} $$\end{document} Below pH = 2.2, the oxidation rate is independent of H(+) Concentration.     

Kinetics of ethanol inhibition in alcohol fermentation

The inhibitory effect of ethanol on yeast growth and fermentation has been studied for the strain Saccharomyces cerevisiae ATCC No. 4126 under anaerobic batch conditions. The results obtained reveal that there is no striking difference between the response of growth and ethanol fermentation. Two kinetic models are also proposed to describe the kinetic pattern of ethanol inhibition on the specific rates of growth and ethanol fermentation: \documentclass{article}\pagestyle{empty}\begin{document}$$\begin{array}{*{20}c} {\frac{{\mu _i }}{{\mu _0 }} = 1{\rm } - {\rm }\left( {\frac{P}{{P_m }}} \right);\alpha } \hfill & {\left( {{\rm for}\ {\rm growth}} \right)} \hfill \\ {\frac{{\nu _i }}{{\nu _0 }} = 1{\rm } - {\rm }\left( {\frac{P}{{P'_m }}} \right);\beta } \hfill & {\left( {{\rm for}\ {\rm ethanol}\ {\rm production}} \right)} \hfill \\ \end{array}$$\end{document} The maximum allowable ethanol concentration above which cells do not grow was predicted to be 112 g/L. The ethanol-producing capability of the cells was completely inhibited at 115 g/L ethanol. The proposed models appear to accurately represent the experimental data obtained in this study and the literature data.     

Topography of nucleic acid helices in solutions. 3. Interactions of spermine and spermidine derivatives with polyadenylic-polyuridylic and polyinosinic-polycytidylic acid helices

The synthesis of spermine derivatives (II), \documentclass{article}\pagestyle{empty}\begin{document}$ {\rm R}_1 {\rm R}_{\rm 2} {\rm R}_{\rm 3} \mathop {\rm N}\limits^ + \left( {{\rm CH}_2 } \right)_3 \mathop {\rm N}\limits^ + {\rm R}_{\rm 1} {\rm R}_{\rm 2} \left( {{\rm CH}_2 } \right)_2 ]_2 \cdot 4{\rm X}^ - $\end{document}, and spermidine derivatives (III), \documentclass{article}\pagestyle{empty}\begin{document}$ {\rm R}_1 {\rm R}_{\rm 2} {\rm R}_{\rm 3} \mathop {\rm N}\limits^ + \left( {{\rm CH}_2 } \right)_4 \mathop {\rm N}\limits^ + {\rm R}_{\rm 1} {\rm R}_{\rm 2} \left( {{\rm CH}_2 } \right)_3 \mathop {\rm N}\limits^ + {\rm R}_{\rm 1} {\rm R}_{\rm 2} {\rm R}_3 \cdot 3{\rm X}^ - $\end{document}, are reported. The effects of these salts on the helix–coil transition of rA–rU and rI–rC helices were examined. Increasing the size of the hydrophobic substituents, R¹, R², and R³ lowers the degree of stabilization of the helical structure. The disproportionation reaction, 2rA–rU→rA–rU₂ + rA occurs readily with salts II and III, especially when the substituents, R₁, R₂, and R₃ are small, i.e., H or Me. Spermine is found to stabilize the rA–rU² and rI–rC helices to approximately the same extent; however, large differences between the degree of stabilization of rA–rU₂ and rI-rC helices are observed when the substituents R₁, R₂, and R₃ are large hydrophobic groups. Similar results are also obtained for the spermidine series. Finally, differences in the interactions of the salts II and III with rA–rU₂ and rI–rC helices suggest that the latter helix is denser.     

Transient method for proposing the mechanisms of reactions over immobilized enzymes

The transient response method is introduced to elucidate the mechanism of reaction over immobilized enzyme. Glucose oxidation over the glucose oxidase that was immobilized on ion-exchange resin using glutaraldehyde as a linking agent is selected as an example here. The transient responses of a fixed-bed reactor to step increases and decreases in glucose, oxygen, and gluconolactone feed concentrations have been monitored and interpreted. From some responses, we have found that gluconolactone is formed in the reaction of glucose with adsorbed oxygen, while hydrogen peroxide is formed in the reaction of oxygen with adsorbed glucose. Combining all information from interpreting the responses with the literature, a mechanistic picture can be obtained as follows: \documentclass{article}\pagestyle{empty}\begin{document}$$ \begin{array}{*{20}c} {E_{{\rm ox}} + G \to E_{{\rm red}} GL} \\ {E_{{\rm red}} GL \to E_{{\rm red}} + GL} \\ {E_{{\rm red}} + {\rm O}_2 \to E_{{\rm ox}} {\rm H}_2 {\rm O}_2 } \\ {E_{{\rm ox}} {\rm H}_2 {\rm O}_2 \to E_{{\rm ox}} + {\rm H}_2 {\rm O}_2 } \\ \end{array} $$\end{document}.     

Kinetics of anaerobic purification of industrial wastewater

As a part of the development of an integral mathematical model describing the up-flow anaerobic sludge blanket (UASB) reactor, the kinetics of the conversion of organic wastes has to be known. We compared the Monod model with the model proposed by Andrews et al. Together with the assumption that the substrate for the anaerobic bacteria is formed by nonionized, volatile fatty acids, the Andrews model is able to describe substrate inhibition and reactor failure due to pH changes.From four batch experiments, with different concentrations of microorganisms, it could be concluded with a reliability of over 95% that the monod model was inadequate and Andrews' model was adequate to describe the measurements. Standard statistical techniques like the X2- and the F-test were used for this purpose.From a parameter sensitivity analysis for the Andrews model it followed that the maximum specific growth rate mu(A) (max) of the bacteria and the inhibition constant K(1) are the parameters which influence the system most. Thus, these parameter were determined experimentally and most accurately. The results are: \documentclass{article}\pagestyle{empty}\begin{document}$$\mu;{A}_{\max} = 16*10;{-4}{\rm h};{-1}\pm 2\%\quad {\rm and}\quad K_l = 0.0158\,{\rm g}\,{\rm HAc/L}\pm 2.5\%$$\end{document} The other parameters were taken from literature. From calculation of the Thiele modulus for the particles it follows that transport limitation of the substrate in the flocus is not significant. The efficiency eta is 0.85 in the worst case.     

Quantifying Lipari–Szabo modelfree parameters from 13CO NMR relaxation experiments

It is proposed to obtain effective Lipari–Szabo order parameters and local correlation times for relaxation vectors of protein ¹³CO nuclei by carrying out a ¹³CO-R₁ auto relaxation experiment, a transverse CSA/dipolar cross correlation and a transverse ¹³CO CSA/¹³CO–¹⁵N CSA/dipolar cross correlation experiment. Given the global rotational correlation time from ¹⁵N relaxation experiments, a new program COMFORD (CO-Modelfree Fitting Of Relaxation Data) is presented to fit the ¹³CO data to an effective order parameter , an effective local correlation time and the orientation of the CSA tensor with respect to the molecular frame. It is shown that the effective is least sensitive to rotational fluctuations about an imaginary axis and most sensitive to rotational fluctuations about an imaginary axis parallel to the NH bond direction. As such, the information is fully complementary to the ¹⁵N relaxation order parameter, which is least sensitive to fluctuations about the NH axis and most sensitive to fluctuations about the axis. The new paradigm is applied on data of Ca²⁺ saturated Calmodulin, and on available literature data for Ubiquitin. Our data indicate that the order parameters rapport on slower, and sometimes different, motions than the ¹⁵N relaxation order parameters. The CO local correlation times correlate well with the calmodulin’s secondary structure. Electronic Supplementary Material Supplementary material is available to authorized users in the online version of this article at .     

Effects of common soil anions and pH on the uptake and accumulation of perchlorate in lettuce

A mechanistic understanding of perchlorate () entry into plants is important for establishing the human health risk associated with consumption of contaminated produce and for assessing the effectiveness of phytoremediation. To determine whether common soil anions affect uptake and accumulation in higher plants, a series of competition experiments using lettuce (Lactuca sativa L.) were conducted between (50 nM) and (4–12 mM), (1–10 mM), or Cl⁻ (5–15 mM) in hydroponic solution. The effects of (0–5 mM) and pH (5.5–7.5) on uptake were also examined. Increasing in solution significantly reduced the amount of taken up by green leaf, butter head, and crisphead lettuces. Sulfate and Cl⁻ had no significant effects on uptake in lettuce over the concentrations tested. Increasing pH significantly reduced the amount of taken up by crisphead and green leaf lettuces, whereas increasing significantly reduced uptake in butter head lettuce. The inhibition by across all lettuce genotypes suggests that may share an ion carrier with , and the decrease in uptake with increasing pH or provides macroscopic evidence for cotransport across the plasma membrane.     

The humus layer determines SO<Subscript>4</Subscript><Superscript>2−</Superscript> isotope values in the mineral soil

Biocycling of sulfur (S) has been proposed to play an important role in the recovery of ecosystems following anthropogenic S deposition. Here, we investigated the importance of the humus layer in the biocycling of S in three forested catchments in the Gårdsjön area of southwestern Sweden with differing S inputs and S isotope signature values. These experimental sites consisted of two reference catchments and the Gårdsjön roof experiment catchment (G1), where anthropogenic deposition was intercepted from 1991 until May 2002 by a roof placed over the entire catchment area. Under the roof, controlled levels of deposition were applied, using a sprinkler system, and the only form of S added was marine SO₄²⁻ with a δ of +19.5‰.We installed ion exchange resin bags at the interface between the humus layer and mineral soil at each of the catchments to collect SO₄²⁻ passing through the humus. The resin bags were installed on four occasions, in 1999 and 2000, covering two summer and two winter periods. The ions collected by each bag during these sampling periods were then eluted and their δ values and SO₄²⁻ concentrations determined. The most striking result is that the average δ value in the resin bags was more than 12‰ lower compared to that of the sprinkler water in the G1 roof catchment. There was no increasing trend in the isotope value in the resin bag SO₄²⁻ despite that the roof treatment has been on-going for almost 10 years; the average value for all resin bags was +7.1‰. The highest δ values found in the G1 roof catchment were between +11‰ and +12‰. However, these values were all obtained from resin bags installed at a single sampling location. Throughfall and resin bag δ values were more similar in the two reference catchments: about +7.5‰ in both cases. There was, however, an increase in resin bag δ values during the first winter period, from about +7‰ to +9‰. The resin bag δ value was linearly and positively related (r² = 0.26, p < 0.001) to the amount of SO₄²⁻ extracted from the resin bags, if relatively high amounts (>50 mmol m⁻²) were excluded. High amounts of resin bag SO₄²⁻ seemed to be related to groundwater inputs, as indicated by the δ value. Our results suggest that rapid immobilization of SO₄²⁻ into a large organic S pool may alter the S isotope value and affect the δ values measured in the mineral soil and runoff.     

Modellierung der enzymatischen Cellobiosehydrolyse – Vergleich linearer und nichtlinearer Parameterbestimmung

Experimental kinetic data (initial rate and high conversion) on the hydrolysis of cellobiose by 1,4-β-glucosidace (Gliocladium sp.) have been analysed and a competitive inhibition by glucose has been proposed. The determination of kinetic parameters from integral data is based upon algorithms for non-linear optimization and numerical integration. The values of kinetic constants \documentclass{article}\pagestyle{empty}\begin{document}$(v_{\max } = 1.02\frac{{\mu {\rm M}_{{\rm glucose}} }}{{{\rm mg}_{{\rm protein}} \cdot \min }},K_M = 2.6{\rm mM/l, and }K_P = 1.2{\rm mM/l)}$\end{document} agree well with the initialrate results. An important distinction is the confidence limit of parameters. Linear regression analysis shows a virtual accuracy and can lead to wrong conclusions.     

Effects of rheological properties and mass transfer on plant cell bioreactor performance: production of tropane alkaloids

Volumetric mass transfer coefficients, K(L)a were measured over an aeration rate range from 0.1 to 1.0 vvm in a 1.2-L draft-tube-type airlift bioreactor for different Datura stramonium cell concentrations and correlated with superficial air velocity and rheological properties of the cell suspension. The measured K(L)a values (17-40 h(-1)) for a cell volume fraction of 0.2 (v/v) were approximately 2 times higher than those for the highest cell concentrations tested (cell volume fraction 0.7-0.8 v/v). Cell suspensions exhibited yield stress and pseudoplastic behavior. This behavior was described by the Casson model. The estimated yield stress values depended upon cell concentration with an exponent of 4.0. An empirical correlation based on the data for plant cell suspensions exhibiting yield stress was developed in order to determine aeration strategy for the plant cell cultivation in draft-tube-type airlift bioreactors: \documentclass{article}\pagestyle{empty}\begin{document}$$ {\rm K}_{\rm L} {\rm a} = {\rm A}({\rm U}_{{\rm gr}});{0.3} ({\rm \eta }_{{\rm eff}});{ - 0.4} $$\end{document} Aeration rates above 1.0 vvm caused a significant drop in cell yield and product content. Maximum growth and production were obtained at 0.6 vvm aeration. The cell and product yields obtained at 1.7 vvm were 2.8 times lower than the maximum values (25 g cell DW/L and 73.8 mg tropane alkaloid/L). The effects of the increased aeration rates on cell yield were also evaluated in terms of Reynolds stress. It was found that there was a relation between cell damage and the estimated Reynolds stress. The Reynolds stress estimated for the same aeration rate decreased with increasing cell concentration, suggesting that cells in the cultures at low cell concentrations are subjected to hydrodynamic damage. In the experiments with the cell cultures having a cell concentration of 0.3 (v/v), approximately 70% reduction in cell concentration was observed when the Reynolds stress was increased from 10 to 50 dyn/cm(2). (c) 1993 John Wiley & Sons, Inc.     

Topography of nucleic acid helices in solutions. II. Structure of the double-stranded rA-rU, rI-rC, acid rA, and the triple-stranded rA-rU2 and rA-rI2 helices

Information concerning the structures of rA–rU, rA–rU₂ rI–rC, rA–rI₂, and acid rA helices in solutions is reported. Through the use of diquaternary ammonium salts of the general structure, \documentclass{article}\pagestyle{empty}\begin{document}$ {\rm R}_1 {\rm R}_2 {\rm R}_3 \mathop {\rm N}\limits^ + ({\rm CH}_2 )n\mathop {\rm N}\limits^ + {\rm R}_1 {\rm R}_2 {\rm R}_3 \cdot 2{\rm Br}^ - $\end{document} (I), it is shown that (1) the distances between adjacent negatively charged oxygen atoms on the helix increases in the following order rA–rI₂ < rI–rC < rA–rU ? rA–rU₂; (2) the density of the helices increases in the order. rA–rI₂ < rA–rU < rA–rU₂ < rI–rC; (3) there is a large hydrophobia site in rA–rI₂ and possibly also in rA–rU, rA–rU₂, and rI–rC helices; (4) the results of the interactions between the salts of type I and the helices may be formulated in semi-quantitative terms by the use of two parameters, α, and β which are shown to be related to the charge separation and the density of the helices, respectively; (5) the studies in solutions compare favorably with the x-ray studies on the fibers; and (6) the acid rA helix differs significantly from the other helices by the fact that the electrostatic interstrand interactions between the negatively charged oxygen atom of a phosphate group and the positively charged 10-amino group of adenine contribute significantly to the stabilization of the helix, and thus it is found that the presence of the salts, I, leads to a significant destabilization of the acid rA helix.     

X-ray crystal structure of a mutant assimilatory nitrite reductase that shows sulfite reductase-like activity

Assimilatory nitrite reductase (aNiR) reduces nitrite ions (NO$\rm{{_{2}^{-}}}$) to ammonium ions (NH$\rm{{_{4}^{+}}}$), whereas assimilatory sulfite reductase reduces sulfite (SO$\rm{{_{3}^{2-}}}$) to hydrogen sulfide (HS(-) ). Although aNiR can also reduce SO$\rm{{_{3}^{2-}}}$, its activity is much lower than when NO$\rm{{_{2}^{-}}}$ is reduced as the substrate. To increase the SO$\rm{{_{3}^{2-}}}$-reduction activity of aNiR, we performed a N226K mutation of Nii3, a representative aNiR. The resulting Nii3-N226K variant could bind non-native targets, SO$\rm{{_{3}^{2-}}}$, and HCO$\rm{{_{3}^{-}}}$, in addition to its native target, i.e., NO$\rm{{_{2}^{-}}}$. We have determined the high-resolution structure of Nii3-N226K in its apo-state and in complex with SO$\rm{{_{3}^{2-}}}$, NO$\rm{{_{2}^{-}}}$, and HCO$\rm{{_{3}^{-}}}$. This analysis revealed conformational changes of Lys226 and the adjacent Lys224 upon binding of SO$\rm{{_{3}^{2-}}}$, but not NO$\rm{{_{2}^{-}}}$. In contrast, HCO$\rm{{_{3}^{-}}}$ binding induced a conformational change at Arg179. After replacing Asn226 with a positively charged Lys, aNiR showed affinity for several anions. A comparison of all ligand-bound structures for Nii3-N226K revealed that structural changes in the active site depend on the size of the substrate.     

A Combined Patch-Clamp and Electrorotation Study of the Voltage- and Frequency-Dependent Membrane Capacitance Caused by Structurally Dissimilar Lipophilic Anions

Interactions of structurally dissimilar anionic compounds with the plasma membrane of HEK293 cells were analyzed by patch clamp and electrorotation. The combined approach provides complementary information on the lipophilicity, preferential affinity of the anions to the inner/outer membrane leaflet, adsorption depth and transmembrane mobility. The anionic species studied here included the well-known lipophilic anions dipicrylamine (DPA⁻), tetraphenylborate (TPB⁻) and [W₂(CO)₁₀(S₂CH)]⁻, the putative lipophilic anion and three new heterocyclic W(CO)₅ derivatives. All tested anions partitioned strongly into the cell membrane, as indicated by the capacitance increase in patch-clamped cells. The capacitance increment exhibited a bell-shaped dependence on membrane voltage. The midpoint potentials of the maximum capacitance increment were negative, indicating the exclusion of lipophilic anions from the outer membrane leaflet. The adsorption depth of the large organic anions DPA⁻, TPB⁻ and increased and that of W(CO)₅ derivatives decreased with increasing concentration of mobile charges. In agreement with the patch-clamp data, electrorotation of cells treated with DPA⁻ and W(CO)₅ derivatives revealed a large dispersion of membrane capacitance in the kilohertz to megahertz range due to the translocation of mobile charges. In contrast, in the presence of TPB⁻ and no mobile charges could be detected by electrorotation, despite their strong membrane adsorption. Our data suggest that the presence of oxygen atoms in the outer molecular shell is an important factor for the fast translocation ability of lipophilic anions.     

Optical anisotropy of polypeptide chains

Optical anisotropies γ² of N-t-butylacetamide (tBA), N-Methylacetamide (MA), and N, N-dimethylacetamide (DMA) have been determined from the Rayleigh ratios for depolarzed scattering by dilute solutions of the amides in p-dioxane. Traceless optical polarizability tensors \documentclass{article}\pagestyle{empty}\begin{document}$ \widehat{\rm \alpha } $\end{document} for the amides are derived from these results in conjunction with the Kerr constant for tBA determined by LeGèvre and co-workers. It is shown that the tensor \documentclass{article}\pagestyle{empty}\begin{document}$ \widehat{\rm \alpha } $\end{document}_i for the glycyle unit in a polypeptide chain may be identified with \documentclass{article}\pagestyle{empty}\begin{document}$ \widehat{\rm \alpha } $\end{document}MA . Methods for deriving corresponding tensors for other peptide units are indicated and the traceless polarizability tensor \documentclass{article}\pagestyle{empty}\begin{document}$ \widehat{\rm \alpha } $\end{document} for a polypeptide chain in any specified configuration is formulated.     

Mixing and power characteristics of drag board device in shallow pool

Mixing and stirring of a 20-m(2) shallow pool by means of a drag board device has been investigated. The board closes the pool cross section except for a slit of a few centimeters above the bottom, and it is slowly moved back and forth, forcing the water to run through the slit and thereby creating a turbulent backwhirl. Power drawn and the drag on the board has been measured together with the velocities of the water at different locations in the wake of the board. Power number N(p) has been correlated with the Reynolds N(Re) and the bottom clearance numbers N(c) by the expressions \documentclass{article}\pagestyle{empty}\begin{document}$$ N_p = 13,465N_{\rm Re};{-0.774} N_c;{0.1016} N_{\rm Re} < 80.000\\N_p = 5.4N_{\rm Re};{-0.0863} N_c;{0.104} N_{\rm Re} > 80.000 $$\end{document} Power and Reynolds numbers are defined as usual with the square root of the board-immersed-area as the characteristic length. The bottom clearance number is defined as the ratio of the water depth in the pool to the difference between water depth and the board width immersed in water. Flow pattern behind the board consists of large vortex loops causing the fluid to circulate from bottom to top and producing a thorough mixing effect. The drag board seems to have several advantages over conventional paddle wheels for the mixing and stirring of algal cultures in shallow ponds.     

Morphometric diffusing capacity and functional anatomy of the book lungs in the spider Tegenaria spp. (Agelenidae)

The presence of both book lungs and a tracheal system in many spiders raises the question of the functional significance of this double respiratory system. The present physiological and morphometric study of the house spider (Tegenaria spp.) reveals that the diffusing capacity (Dto₂) of the lungs alone suffices during rest and following exercise to meet measured rates of oxygen consumption (\documentclass{article}\pagestyle{empty}\begin{document}$ \mathop {\rm V}\limits^{\rm.} $\end{document}o₂) at driving pressures (ΔPto ₂) similar to those calculated for vertebrate lungs. During moulting ΔPto ₂ may rise to more than double the vertebrate values, implying the possible insufficiency of book lungs during this critical life phase. Resting \documentclass{article}\pagestyle{empty}\begin{document}$ \mathop {\rm V}\limits^{\rm .} $\end{document}o₂ is greatest (92 mm³/h · g) during the early morning and lowest (66 mm³/h · g) near midday: during moulting \documentclass{article}\pagestyle{empty}\begin{document}$ \mathop {\rm V}\limits^{\rm .} $\end{document}o₂ rises to 278.7 mm³/h · g. In spiders recovering from exercise \documentclass{article}\pagestyle{empty}\begin{document}$ \mathop {\rm V}\limits^{\rm .} $\end{document}o₂ is consistently greater than during rest: neither value is significantly reduced by blockage of the tracheal stigmas. Regression calculations of morphometric values for a hypothetical 100-mg Tegenaria yield a total lung volume of 0.578 mm³, a pulmonary surface area of 69.8 mm², and a surface-to-volume ratio of 120.89 mm²/mm³. In spite of the similar thickness of the chitinous and hypodermal components of the air-hemolymph barrier (each ca. 0.2 μm in nonmoulting animals), the low permeability of chitin for oxygen makes this layer the greater barrier to diffusion. For a 100-mg specimen Dto₂ is 3.5 mm³/h · torr: similar to that of a turtle (Pseudemys) on a gram-body weight basis.     

The mechanism and kinetics of decomposition of 5-aminotetrazole

The pathway and ab initio direct kinetics of the decomposition 5-aminotetrazole (5-ATZ) to HN₃ and NH₂CN was investigated. Reactant, products and transition state were optimized with MP2 and B3LYP methods using 6–311G** and aug-cc-pVDZ basis sets. The intrinsic reaction coordinate curve of the reaction was calculated using the MP2 method with 6–311G** basis set. The energies were refined using CCSD(T)/6–311G**. Rate constants were evaluated by conventional transition-state theory (CVT) and canonical variational transition-state theory (TST), with tunneling effect over 300 to 2,500 K. The results indicated that the tunneling effect and the variational effect are small for the calculated rate constants. The fitted three-parameter expression calculated using the CVT and TST methods are and , respectively. Figure The mechanism of the decomposition process of 5-ATZ to HN₃ and NH₂CN