Enhanced enzymatic hydrolysis and structural features of corn stover by FeCl3 pretreatment

Corn stover was pretreated with FeCl₃ to remove almost all of the hemicellulose present and then hydrolyzed with cellulase and β-glucosidase to produce glucose. Enzymatic hydrolysis of corn stover that had been pretreated with FeCl₃ at 160 °C for 20 min resulted in an optimum yield of 98.0%. This yield was significantly higher than that of untreated corn stover (22.8%). FeCl₃ pretreatment apparently damaged the surface of corn stover and significantly increased the enzymatic digestibility, as evidenced by SEM and XRD analysis data. FTIR analysis indicated that FeCl₃ pretreatment could disrupt almost all the ether linkages and some ester linkages between lignin and carbohydrates but had no effect on delignification. The FeCl₃ pretreatment technique, as a novel pretreatment method, enhances enzymatic hydrolysis of lignocellulosic biomass by destructing chemical composition and altering structural features.     

Effect of hemicellulose and lignin removal on enzymatic hydrolysis of steam pretreated corn stover

Ethanol can be produced from lignocellulosic biomass using steam pretreatment followed by enzymatic hydrolysis and fermentation. The sugar yields, from both hemicellulose and cellulose are critical parameters for an economically-feasible ethanol production process. This study shows that a near-theoretical glucose yield (96-104%) from acid-catalysed steam pretreated corn stover can be obtained if xylanases are used to supplement cellulases during hydrolysis. Xylanases hydrolyse residual hemicellulose, thereby improving the access of enzymes to cellulose. Under these conditions, xylose yields reached 70-74%. When pre-treatment severity was reduced by using autocatalysis instead of acid-catalysed steam pretreatment, xylose yields were increased to 80-86%. Partial delignification of pretreated material was also evaluated as a way to increase the overall sugar yield. The overall glucose yield increased slightly due to delignification but the overall xylose yield decreased due to hemicellulose loss in the delignification step. The data also demonstrate that steam pretreatment is a robust process: corn stover from Europe and North America showed only minor differences in behaviour.     

Effect of biological pretreatment with Trametes hirsuta yj9 on enzymatic hydrolysis of corn stover

In this study, a newly isolated Trametes hirsuta yj9 was used to pretreat corn stover in order to enhance enzymatic digestibility. T. hirsuta yj9 preferentially degraded lignin to be as high as 71.49% after 42-day pretreatment. Laccase and xylanase was the major ligninolytic and hydrolytic enzyme, respectively and filter paper activity (FPA) increased gradually with prolonged pretreatment time. Sugar yields increased significantly after pretreatment with T. hirsuta yj9, reaching an enzymatic digestibility of 73.99% after 42 days of pretreatment. Scanning electron microscopy (SEM) showed significant structural changes in pretreated corn stover, the surface of pretreated corn stover became increasingly coarse, the gaps between cellulose fibers were visible, and many pores were developed. Correlation analysis showed that sugar yields were inversely proportional to the lignin contents, less related to cellulose and hemicellulose contents.     

The pretreatment of corn stover with Gloeophyllum trabeum KU-41 for enzymatic hydrolysis

Background

Pretreatment is an essential step in the enzymatic hydrolysis of biomass for bio-ethanol production. The dominant concern in this step is how to decrease the high cost of pretreatment while achieving a high sugar yield. Fungal pretreatment of biomass was previously reported to be effective, with the advantage of having a low energy requirement and requiring no application of additional chemicals. In this work, Gloeophyllum trabeum KU-41 was chosen for corn stover pretreatment through screening with 40 strains of wood-rot fungi. The objective of the current work is to find out which characteristics of corn stover pretreated with G. trabeum KU-41 determine the pretreatment method to be successful and worthwhile to apply. This will be done by determining the lignin content, structural carbohydrate, cellulose crystallinity, initial adsorption capacity of cellulase and specific surface area of pretreated corn stover.

Results

The content of xylan in pretreated corn stover was decreased by 43% in comparison to the untreated corn stover. The initial cellulase adsorption capacity and the specific surface area of corn stover pretreated with G. trabeum were increased by 7.0- and 2.5-fold, respectively. Also there was little increase in the cellulose crystallinity of pretreated corn stover.

Conclusion

G. trabeum has an efficient degradation system, and the results indicated that the conversion of cellulose to glucose increases as the accessibility of cellulose increases due to the partial removal of xylan and the structure breakage of the cell wall. This pretreatment method can be further explored as an alternative to the thermochemical pretreatment method.     

Lime pretreatment and enzymatic hydrolysis of corn stover

Corn stover was pretreated with an excess of calcium hydroxide (0.5 g Ca(OH)2/g raw biomass) in non-oxidative and oxidative conditions at 25, 35, 45, and 55 degrees C. The optimal condition is 55 degrees C for 4 weeks with aeration. Glucan (91.3%) and xylan (51.8%) were converted to glucose and xylose respectively, when the treated corn stover was enzymatically hydrolyzed with 15 FPU/g cellulose. Only 0.073 g Ca(OH)2 was consumed per g of raw corn stover. Of the initial lignin, 87.5% was maximally removed. Almost all acetyl groups were removed. After 4 weeks at 55 degrees C with aeration, some cellulose and hemicellulose were solubilized as monomers and oligomers in the pretreatment liquor. When considering the dissolved fragments of glucan and xylan in the pretreatment liquor, the overall yields of glucose and xylose were 93.2% and 79.5% at 15 FPU/g cellulose. The pretreatment liquor has no inhibitory effect on ethanol fermentation.     

Dilute sulfuric acid cycle spray flow-through pretreatment of corn stover for enhancement of sugar recovery

A cycle spray flow-through reactor was designed and used to pretreat corn stover in dilute sulfuric acid medium. The dilute sulfuric acid cycle spray flow-through (DCF) process enhanced xylose sugar yields and cellulose digestibility while increasing the removal of lignin. Within the DCF system, the xylose sugar yields of 90–93% could be achieved for corn stover pretreated with 2% (w/v) dilute sulfuric acid at 95 °C during the optimal reaction time (90 min). The remaining solid residue exhibited enzymatic digestibility of 90–95% with cellulase loading of 60 FPU/g glucan that was due to the effective lignin removal (70–75%) in this process. Compared with flow-through and compress-hot water pretreatment process, the DCF method produces a higher sugar concentration and higher xylose monomer yield. The novel DCF process provides a feasible approach for lignocellulosic material pretreatment.     

Supercritical carbon dioxide pretreatment of corn stover and switchgrass for lignocellulosic ethanol production

Supercritical CO₂ (SC-CO₂), a green solvent suitable for a mobile lignocellulosic biomass processor, was used to pretreat corn stover and switchgrass at various temperatures and pressures. The CO₂ pressure was released as quickly as possible by opening a quick release valve during the pretreatment. The biomass was hydrolyzed after pretreatment using cellulase combined with β-glucosidase. The hydrolysate was analyzed for the amount of glucose released. Glucose yields from corn stover samples pretreated with SC-CO₂ were higher than the untreated sample’s 12% glucose yield (12 g/100 g dry biomass) and the highest glucose yield of 30% was achieved with SC-CO₂ pretreatment at 3500 psi and 150 °C for 60 min. The pretreatment method showed very limited improvement (14% vs. 12%) in glucose yield for switchgrass. X-ray diffraction results indicated no change in crystallinity of the SC-CO₂ treated corn stover when compared to the untreated, while SEM images showed an increase in surface area.     

Simultaneous saccharification and fermentation of lime-treated biomass

Simultaneous saccharification and fermentation (SSF) was performed on lime-treated switchgrass and corn stover, and oxidatively lime-treated poplar wood to determine their compatibility with Saccharomyces cerevisiae. Cellulose-derived glucose was extensively utilized by the yeast during SSF. The ethanol yields from pretreated switchgrass, pretreated corn stover, and pretreated-and-washed poplar wood were 72%, 62% and 73% of theoretical, respectively, whereas those from -cellulose were 67 to 91% of theoretical. The lower ethanol yields from treated biomass resulted from lower cellulose digestibilities rather than inhibitors produced by the pretreatment. Oxidative lime pretreatment of poplar wood increased the ethanol yield by a factor of 5.6, from 13% (untreated) to 73% (pretreated-and-washed).     

Partial flow of compressed-hot water through corn stover to enhance hemicellulose sugar recovery and enzymatic digestibility of cellulose

Flowthrough pretreatment with compressed-hot water can significantly increase the removal of xylan and lignin and enhance xylose sugar yields and cellulose digestibility, especially at high flow rates. However, continuous flowthrough operations that realize these benefits suffer from a large amount of water consumption that leads to high energy requirements for pretreatment and downstream processing. Because high flow rates are particularly effective early in hemicellulose hydrolysis and less effective later, flow with compressed-hot water was applied at selected intervals, and performance was compared with that of batch and flowthrough operations for corn stover pretreated with compressed-hot water at 200 degrees C. Partial flow reduced water consumption by 60% compared with continuous flowthrough operation but still achieved higher xylose sugar yields (84-89%) compared to batch pretreatment (46.6%). In addition, corn stover cellulose pretreated by partial flow had higher enzymatic digestibility (88-90%) than batch operations (approximately 85%) at otherwise identical conditions, apparently due to much higher lignin removal for the former (40-45% vs 10-12%). Partial flow also reduced degradation, with recovery of xylose and glucose in the solids and hydrolyzate increased to 90-92% vs only about 76% for batch operation. The partial flow approach could be further improved by optimizing the operating strategy and reaction conditions, suggesting that this novel pretreatment could lead to advanced biomass pretreatment technology.     

Influence of physico-chemical changes on enzymatic digestibility of ionic liquid and AFEX pretreated corn stover

Ionic liquid (IL) and ammonia fiber expansion (AFEX) pretreatments were studied to develop the first direct side-by-side comparative assessment on their respective impacts on biomass structure, composition, process mass balance, and enzymatic saccharification efficiency. AFEX pretreatment completely preserves plant carbohydrates, whereas IL pretreatment extracts 76% of hemicellulose. In contrast to AFEX, the native crystal structure of the recovered corn stover from IL pretreatment was significantly disrupted. For both techniques, more than 70% of the theoretical sugar yield was attained after 48 h of hydrolysis using commercial enzyme cocktails. IL pretreatment requires less enzyme loading and a shorter hydrolysis time to reach 90% yields. Hemicellulase addition led to significant improvements in the yields of glucose and xylose for AFEX pretreated corn stover, but not for IL pretreated stover. These results provide new insights into the mechanisms of IL and AFEX pretreatment, as well as the advantages and disadvantages of each.     

Physical and chemical characterizations of corn stover and poplar solids resulting from leading pretreatment technologies

In order to investigate changes in substrate chemical and physical features after pretreatment, several characterizations were performed on untreated (UT) corn stover and poplar and their solids resulting pretreatments by ammonia fiber expansion (AFEX), ammonia recycled percolation (ARP), controlled pH, dilute acid, flowthrough, lime, and SO₂ technologies. In addition to measuring the chemical compositions including acetyl content, physical attributes determined were biomass crystallinity, cellulose degree of polymerization, cellulase adsorption capacity of pretreated solids and enzymatically extracted lignin, copper number, FT-IR responses, scanning electron microscopy (SEM) visualizations, and surface atomic composition by electron spectroscopy of chemical analysis (ESCA). Lime pretreatment removed the most acetyl groups from both corn stover and poplar, while AFEX removed the least. Low pH pretreatments depolymerized cellulose and enhanced biomass crystallinity much more than higher pH approaches. Lime pretreated corn stover solids and flowthrough pretreated poplar solids had the highest cellulase adsorption capacity, while dilute acid pretreated corn stover solids and controlled pH pretreated poplar solids had the least. Furthermore, enzymatically extracted AFEX lignin preparations for both corn stover and poplar had the lowest cellulase adsorption capacity. ESCA results showed that SO₂ pretreated solids had the highest surface O/C ratio for poplar, but for corn stover, the highest value was observed for dilute acid pretreatment with a Parr reactor. Although dependent on pretreatment and substrate, FT-IR data showed that along with changes in cross linking and chemical changes, pretreatments may also decrystallize cellulose and change the ratio of crystalline cellulose polymorphs (Iα/Iβ).     

Influence of xylan on the enzymatic hydrolysis of steam‐pretreated corn stover and hybrid poplar

The focus of this study was to alter the xylan content of corn stover and poplar using SO₂‐catalyzed steam pretreatment to determine the effect on subsequent hydrolysis by commercial cellulase preparations supplemented with or without xylanases. Steam pretreated solids with xylan contents ranging from ～1 to 19% (w/w) were produced. Higher xylan contents and improved hemicellulose recoveries were obtained with solids pretreated at lower severities or without SO₂‐addition prior to pretreatment. The pretreated solids with low xylan content (<4% (w/w)) were characterized by fast and complete cellulose to glucose conversion when utilizing cellulases. Commercial cellulases required xylanase supplementation for effective hydrolysis of pretreated substrates containing higher amounts of xylan. It was apparent that the xylan content influenced both the enzyme requirements for hydrolysis and the recovery of sugars during the pretreatment process. © 2009 American Institute of Chemical Engineers Biotechnol. Prog., 2009     

Production of ethanol from corn stover hemicellulose hydrolyzate using <Emphasis Type="Italic">Pichia stipitis</Emphasis>

Hemicellulose liquid hydrolyzate from dilute acid pretreated corn stover was fermented to ethanol using Pichia stipitis CBS 6054. The fermentation rate increased with aeration but the pH also increased due to consumption of acetic acid by Pichia stipitis. Hemicellulose hydrolyzate containing 34 g/L xylose, 8 g/L glucose, 8 g/L Acetic acid, 0.73 g/L furfural, and 1 g/L hydroxymethyl furfural was fermented to 15 g/L ethanol in 72 h. The yield in all the hemicellulose hydrolyzates was 0.37–0.44 g ethanol/g (glucose + xylose). Nondetoxified hemicellulose hydrolyzate from dilute acid pretreated corn stover was fermented to ethanol with high yields, and this has the potential to improve the economics of the biomass to ethanol process.     

Optimization of microwave-assisted FeCl3 pretreatment conditions of rice straw and utilization of Trichoderma viride and Bacillus pumilus for production of reducing sugars

In this study, Box-Behnken design (BBD) and response surface methodology (RSM) were used to optimize microwave-assisted FeCl₃ pretreatment conditions of rice straw with respect to FeCl₃ concentration, microwave intensity, irradiation time and substrate concentration. When rice straw was pretreated at the optimal conditions of FeCl₃ concentration, 0.14 mol/L; microwave intensity, 160 °C; irradiation time, 19 min; substrate concentration, 109 g/L; and inoculated with Trichoderma viride and Bacillus pumilus, the production of reducing sugars was 6.62 g/L. This yield was 2.9 times higher than that obtained with untreated rice straw. The microorganisms degraded 37.8% of pretreated rice straw after 72 h. The structural characteristic analyses suggest that microwave-assisted FeCl₃ pretreatment damaged the silicified waxy surface of rice straw, disrupted almost all the ether linkages between lignin and carbohydrates, and removed lignin.     

Synthesis of aromatic amino acids from 2G lignocellulosic substrates

Pseudomonas putida is a highly solvent-resistant microorganism and useful chassis for the production of value-added compounds from lignocellulosic residues, in particular aromatic compounds that are made from phenylalanine. The use of these agricultural residues requires a two-step treatment to release the components of the polysaccharides of cellulose and hemicellulose as monomeric sugars, the most abundant monomers being glucose and xylose. Pan-genomic studies have shown that Pseudomonas putida metabolizes glucose through three convergent pathways to yield 6-phosphogluconate and subsequently metabolizes it through the Entner–Doudoroff pathway, but the strains do not degrade xylose. The valorization of both sugars is critical from the point of view of economic viability of the process. For this reason, a P. putida strain was endowed with the ability to metabolize xylose via the xylose isomerase pathway, by incorporating heterologous catabolic genes that convert this C5 sugar into intermediates of the pentose phosphate cycle. In addition, the open reading frame T1E_2822, encoding glucose dehydrogenase, was knocked-out to avoid the production of the dead-end product xylonate. We generated a set of DOT-T1E-derived strains that metabolized glucose and xylose simultaneously in culture medium and that reached high cell density with generation times of around 100 min with glucose and around 300 min with xylose. The strains grew in 2G hydrolysates from diluted acid and steam explosion pretreated corn stover and sugarcane straw. During growth, the strains metabolized > 98% of glucose, > 96% xylose and > 85% acetic acid. In 2G hydrolysates P. putida 5PL, a DOT-T1E derivative strain that carries up to five independent mutations to avoid phenylalanine metabolism, accumulated this amino acid in the medium. We constructed P. putida 5PLΔgcd (xylABE) that produced up to 250 mg l⁻¹ of phenylalanine when grown in 2G pretreated corn stover or sugarcane straw. These results support as a proof of concept the potential of P. putida as a chassis for 2G processes.     

Comparative study of corn stover pretreated by dilute acid and cellulose solvent‐based lignocellulose fractionation: Enzymatic hydrolysis,supramolecular structure,and substrate accessibility

Liberation of fermentable sugars from recalcitrant biomass is among the most costly steps for emerging cellulosic ethanol production. Here we compared two pretreatment methods (dilute acid, DA, and cellulose solvent and organic solvent lignocellulose fractionation, COSLIF) for corn stover. At a high cellulase loading [15 filter paper units (FPUs) or 12.3 mg cellulase per gram of glucan], glucan digestibilities of the corn stover pretreated by DA and COSLIF were 84% at hour 72 and 97% at hour 24, respectively. At a low cellulase loading (5 FPUs per gram of glucan), digestibility remained as high as 93% at hour 24 for the COSLIF‐pretreated corn stover but reached only ～60% for the DA‐pretreated biomass. Quantitative determinations of total substrate accessibility to cellulase (TSAC), cellulose accessibility to cellulase (CAC), and non‐cellulose accessibility to cellulase (NCAC) based on adsorption of a non‐hydrolytic recombinant protein TGC were measured for the first time. The COSLIF‐pretreated corn stover had a CAC of 11.57 m²/g, nearly twice that of the DA‐pretreated biomass (5.89 m²/g). These results, along with scanning electron microscopy images showing dramatic structural differences between the DA‐ and COSLIF‐pretreated samples, suggest that COSLIF treatment disrupts microfibrillar structures within biomass while DA treatment mainly removes hemicellulose. Under the tested conditions COSLIF treatment breaks down lignocellulose structure more extensively than DA treatment, producing a more enzymatically reactive material with a higher CAC accompanied by faster hydrolysis rates and higher enzymatic digestibility. Biotechnol. Bioeng. 2009;103: 715–724. © 2009 Wiley Periodicals, Inc.     

Development and validation of a kinetic model for enzymatic saccharification of lignocellulosic biomass

A multireaction kinetic model was developed for closed-system enzymatic hydrolysis of lignocellulosic biomass such as corn stover. Three hydrolysis reactions were modeled, two heterogeneous reactions for cellulose breakdown to cellobiose and glucose and one homogeneous reaction for hydrolyzing cellobiose to glucose. Cellulase adsorption onto pretreated lignocellulose was modeled via a Langmuir-type isotherm. The sugar products of cellulose hydrolysis, cellobiose and glucose, as well as xylose, the dominant sugar prevalent in most hemicellulose hydrolyzates, were assumed to competitively inhibit the enzymatic hydrolysis reactions. Model parameters were estimated from experimental data generated using dilute acid pretreated corn stover as the substrate. The model performed well in predicting cellulose hydrolysis trends at experimental conditions both inside and outside the design space used for parameter estimation and can be used for in silico process optimization.     

Genetic Engineering of Enterobacter asburiae Strain JDR-1 for Efficient Production of Ethanol from Hemicellulose Hydrolysates

Dilute acid pretreatment is an established method for hydrolyzing the methylglucuronoxylans of hemicellulose to release fermentable xylose. In addition to xylose, this process releases the aldouronate methylglucuronoxylose, which cannot be metabolized by current ethanologenic biocatalysts. Enterobacter asburiae JDR-1, isolated from colonized wood, was found to efficiently ferment both methylglucuronoxylose and xylose in acid hydrolysates of sweet gum xylan, producing predominantly ethanol and acetate. Transformation of E. asburiae JDR-1 with pLOI555 or pLOI297, each containing the PET operon containing pyruvate decarboxylase (pdc) and alcohol dehydrogenase B (adhB) genes derived from Zymomonas mobilis, replaced mixed-acid fermentation with homoethanol fermentation. Deletion of the pyruvate formate lyase (pflB) gene further increased the ethanol yield, resulting in a stable E. asburiae E1(pLOI555) strain that efficiently utilized both xylose and methylglucuronoxylose in dilute acid hydrolysates of sweet gum xylan. Ethanol was produced from xylan hydrolysate by E. asburiae E1(pLOI555) with a yield that was 99% of the theoretical maximum yield and at a rate of 0.11 g ethanol/g (dry weight) cells/h, which was 1.57 times the yield and 1.48 times the rate obtained with the ethanologenic strain Escherichia coli KO11. This engineered derivative of E. asburiae JDR-1 that is able to ferment the predominant hexoses and pentoses derived from both hemicellulose and cellulose fractions is a promising subject for development as an ethanologenic biocatalyst for production of fuels and chemicals from agricultural residues and energy crops.Lignocellulosic resources, including forest and agricultural residues and evolving energy crops, offer benign alternatives to petroleum-based resources for production of fuels and chemicals. As renewable resources, these lignocellulosic materials are expected to decrease dependence on exhaustible supplies of petroleum and mitigate the net release of carbon dioxide into the atmosphere. The development of economically acceptable bioconversion processes requires pretreatments that release the maximal quantities of hexoses (predominantly glucose released from cellulose) and pentoses (arabinose and xylose) from hemicelluloses and also requires microbial biocatalysts that efficiently convert these compounds to a single targeted product.As one of three main components of lignocellulosics, hemicellulose contains polysaccharides comprised of pentoses, hexoses and sugar acids that account for 20 to 35% of the total biomass from different sources (21). Methylglucuronoxylans (MeGAX_n), consisting of long chains of as many as 70 β-xylopyranose residues linked by β-1,4-glycosidic bonds (25), are the predominant components in the hemicellulose fractions of agricultural residues and energy crops, including corn stover, sugarcane bagasse, poplar, and switchgrass (7, 18, 23, 24). In hardwood and softwood xylans, a 4-O-methylglucuronic acid is attached at the 2′ position of every sixth to eighth xylose residue (12, 15). Dilute acid hydrolysis is commonly used to make the monosaccharides comprising hemicellulose accessible for fermentation (7, 22). However, the α-1,2 glucuronosyl linkage in xylan is resistant to dilute acid hydrolysis, which results in the release of methylglucuronoxylose (MeGAX) along with xylose and other monosaccharides. MeGAX is not fermented by bacterial biocatalysts currently used to convert hemicellulose to ethanol, such as Escherichia coli KO11 (2, 6). In sweet gum xylan, as much as 27% of the carbohydrate may be in this unfermentable fraction after dilute acid pretreatment (2, 20). Complete utilization of all hemicellulosic sugars can improve the efficiency of conversion of lignocellulosic materials to fuel ethanol and other value-added products.Our previous research on the processing of hemicelluloses for fermentation led to isolation of Enterobacter asburiae strain JDR-1. This isolate performed mixed-acid fermentation of the principal hexoses and pentoses that can be derived from cellulose and hemicellulose fractions of lignocellulosic biomass and exhibited a novel metabolic potential based on its ability to ferment MeGAX and xylose to ethanol and acetate as major fermentation products from sweet gum MeGAX_n hydrolysates generated by dilute acid pretreatment (2). This strain has been genetically modified to produce d-(−)-lactate as the predominant product from acid hydrolysates of MeGAX_n (3).In this study, the PET operon containing the pdc, adhA, and adhB genes from Zymomonas mobilis (10, 11) was incorporated into a pflB E. asburiae JDR-1 isolate by plasmid transformation to construct homoethanologenic strains. The resulting recombinant strains were compared with E. asburiae wild-type strain JDR-1 and the ethanologenic strain E. coli KO11 to evaluate their efficiencies of production of ethanol from dilute acid hydrolysates of sweet gum MeGAX_n.     

Optimization of pH controlled liquid hot water pretreatment of corn stover

Controlled pH, liquid hot water pretreatment of corn stover has been optimized for enzyme digestibility with respect to processing temperature and time. This processing technology does not require the addition of chemicals such as sulfuric acid, lime, or ammonia that add cost to the process because these chemicals must be neutralized or recovered in addition to the significant expense of the chemicals themselves. Second, an optimized controlled pH, liquid hot water pretreatment process maximizes the solubilization of the hemicellulose fraction as liquid soluble oligosaccharides while minimizing the formation of monomeric sugars. The optimized conditions for controlled pH, liquid hot water pretreatment of a 16% slurry of corn stover in water was found to be 190 degrees C for 15 min. At the optimal conditions, 90% of the cellulose was hydrolyzed to glucose by 15FPU of cellulase per gram of glucan. When the resulting pretreated slurry, in undiluted form, was hydrolyzed by 11FPU of cellulase per gram of glucan, a hydrolyzate containing 32.5 g/L glucose and 18 g/L xylose was formed. Both the xylose and the glucose in this undiluted hydrolyzate were shown to be fermented by recombinant yeast 424A(LNH-ST) to ethanol at 88% of theoretical yield.     

EFFICIENT PRODUCTION OF BIOETHANOL FROM CORN STOVER BY PRETREATMENT WITH A COMBINATION OF SULFURIC ACID AND SODIUM HYDROXIDE

Corn stover is the most abundant agricultural residue in China and a valuable reservoir for bioethanol production. In this study, we proposed a process for producing bioethanol from corn stover; the pretreatment prior to presaccharification, followed by simultaneous saccharification and fermentation (SSF) by using a flocculating Saccharomyces cerevisiae strain, was optimized. Pretreatment with acid–alkali combination (1% H₂SO₄, 150°C, 10 min, followed by 1% NaOH, 80°C, 60 min) resulted in efficient lignin removal and excellent recovery of xylose and glucose. A glucose recovery efficiency of 92.3% was obtained by enzymatic saccharification, when the pretreated solid load was 15%. SSF was carried out at 35°C for 36 hr after presaccharification at 50°C for 24 hr, and an ethanol yield of 88.2% was achieved at a solid load of 15% and an enzyme dosage of 15 FPU/g pretreated corn stover.