Development of Sulfidogenic Sludge from Marine Sediments and Trichloroethylene Reduction in an Upflow Anaerobic Sludge Blanket Reactor

The importance of microbial sulfate reduction relies on the various applications that it offers in environmental biotechnology. Engineered sulfate reduction is used in industrial wastewater treatment to remove large concentrations of sulfate along with the chemical oxygen demand (COD) and heavy metals. The most common approach to the process is with anaerobic bioreactors in which sulfidogenic sludge is obtained through adaptation of predominantly methanogenic granular sludge to sulfidogenesis. This process may take a long time and does not always eliminate the competition for substrate due to the presence of methanogens in the sludge. In this work, we propose a novel approach to obtain sulfidogenic sludge in which hydrothermal vents sediments are the original source of microorganisms. The microbial community developed in the presence of sulfate and volatile fatty acids is wide enough to sustain sulfate reduction over a long period of time without exhibiting inhibition due to sulfide. This protocol describes the procedure to generate the sludge from the sediments in an upflow anaerobic sludge blanket (UASB) type of reactor. Furthermore, the protocol presents the procedure to demonstrate the capability of the sludge to remove by reductive dechlorination a model of a highly toxic organic pollutant such as trichloroethylene (TCE). The protocol is divided in three stages: (1) the formation of the sludge and the determination of its sulfate reducing activity in the UASB, (2) the experiment to remove the TCE by the sludge, and (3) the identification of microorganisms in the sludge after the TCE reduction. Although in this case the sediments were taken from a site located in Mexico, the generation of a sulfidogenic sludge by using this procedure may work if a different source of sediments is taken since marine sediments are a natural pool of microorganisms that may be enriched in sulfate reducing bacteria.     

Rapid granulation and sludge retention for tetrachloroethylene removal in an upflow anaerobic sludge blanket reactor

A laboratory scale upflow anaerobic sludge blanket (UASB) reactor was operated at 35 °C for over 200 days to investigate the granulation mechanism during tetrachloroethylene (TCE) biodegradation. Anaerobic, unacclimated sludge and glucose were used as seed and primary substrate, respectively. TCE-degrading granules developed after 1.5 months of start-up. They grew at an accelerated pace for 7 months. The TCE-degrading granules had a maximum diameter of 2.5 mm and specific methanogenic activity of 1.32 g chemical oxygen demand (COD) g^–1 total suspended solid (TSS) day^–1. 94% COD and 90% TCE removal efficiencies were achieved when the reactor was operating at loading rates as high as 160 mg TCE l^–1 day^–1 and 14 g COD l^–1 day^–1, after 230 days of continuous operation.     

Improvement of the anaerobic treatment of potato processing wastewater in a UASB reactor by co-digestion with glycerol

The effect of three different types of glycerol on the performance of up-flow anaerobic sludge blanket (UASB) reactors treating potato processing wastewater was investigated. High COD removal efficiencies were obtained in both control and supplemented UASB reactors (around 85%). By adding 2 ml glycerol product per liter of raw wastewater, the biogas production could be increased by 0.74 l biogas ml⁻¹ glycerol product, which leads to energy values in the range of 810–1270 kWh_electric per m³ product. Moreover, a better in-reactor biomass yield was observed for the supplemented UASB reactor (0.012 g VSS g⁻¹ COD_removed) compared to the UASB control (0.002 g VSS g⁻¹ COD_removed), which suggests a positive effect of glycerol on the sludge blanket growth.     

Long-term adaptation of methanol-fed thermophilic (55 °C) sulfate-reducing reactors to NaCl

A laboratory-scale upflow anaerobic sludge bed (UASB) reactor was operated during 273 days at increasing NaCl concentrations (0.5–12.5 g NaCl l^–1) to assess whether the stepwise addition of the salt NaCl results in the acclimation of that sludge. The 6.5-l thermophilic (55 °C), sulfidogenic [a chemical oxygen demand (COD) to SO₄^2– ratio of 0.5] UASB reactor operated at an organic loading rate of 5 g COD l^–1 day^–1, a hydraulic retention time of 10 h and was fed with methanol as the sole electron donor. The results show that the adaptation of the thermophilic, sulfidogenic methanol-degrading biomass to a high osmolarity environment is unlikely to occur. Sulfide was the main mineralization product from methanol degradation, regardless of the NaCl concentration added to the influent. However, sulfide production in the reactor steadily decreased after the addition of 7.5 g NaCl l^–1, whereas acetate production was stimulated at that influent NaCl concentration. Batch tests performed with sludge harvested from the UASB reactor when operating at different influent salinities confirmed that acetate is the main metabolic product at NaCl concentrations higher than 12.5 g l^–1. The apparent order of NaCl toxicity towards the different trophic groups was found to be: sulfate-reducing bacteria > methane-producing archaea > acetogenic bacteria.     

The influence of anaerobic pretreatment on the nitrogen removal from biosynthetic pharmaceutical wastewaters

The C:N ratio of the pharmaceutical wastewaters is usually suitable for a combination of the anaerobic pretreatment with the high COD removal and aerobic posttreatment with the efficient biological N removal. This kind of anaerobic-aerobic process was tested in semipilot scale by using a UASB reactor and an activated sludge system with a predenitrification (total volume 100 1). It was found that at a total HRT of 2.3 days an average of 97.5% of COD and 73.5% of total N was removed. The UASB reactor was operated at 30°C with a volumetric loading rate of 8.7 kg.m^-3.d^-1, the efficiency of COD removal was 92.2%. The processes, which take part in the biological removal of nitrogen, especially the nitrification, were running with lower rates than usually observed in aerobic treatment systems.Abbreviations AAO anaerobic anoxic oxic configuration - AOO anaerobic oxic oxic configuration - B _V volumetric organic loading rate (kg COD.m^-3. d^-1) - dB _x specific COD removal rate (mg COD. g^-1 VSS. d^-1) - DNR denitrification rate (mg N–NO₃. g^-1 VSS. h^-1) - E_COD efficiency of COD removal (%) - HRT hydraulic retention time (d) - NR nitrification rate (mg N–NO₃. g^-1 VSS. h^-1) - R recirculation ratio (%) - SBP specific biogas production (m³.kg^-1 removed COD) - SRT solids retention time; sludge age (d) - SS suspended solids (g.1^-1) - UASB upflow anaerobic sludge blanket reactor - VSS volatile suspended solids (g.1^-1)     

Lead removal through biological sulfate reduction process

The feasibility of lead removal through biological sulfate reduction process with ethanol as electron donor was investigated. Sulfide-rich effluent from biological process was used to remove lead as lead sulfide precipitate. The experiments were divided into two stages; Stage I startup and operation of sulfidogenic process in a UASB reactor and Stage II lead sulfide precipitation. In Stage I, the COD:S ratio was gradually reduced from 15:1 to 2:1. At the COD:S ratio of 2:1, sulfidogenic condition was achieved as identified by 80-85% of electron flow by sulfate reducing bacteria (SRB). COD and sulfate removal efficiency were approximately 78% and 50%, respectively. In Stage II, the effluent from UASB reactor containing sulfide in the range of 30-50 mg/L and lead-containing solution of 45-50 mg/L were fed continuously into the precipitation chamber in which the optimum pH for lead sulfide precipitation of 7.5-8.5 was maintained. It was found that lead removal of 85-95% was attained.     

Flocculants effect in biomass retention in a UASB reactor treating dairy manure

The performance and biomass retention of an upflow anaerobic sludge bed (UASB) reactor treating liquid fraction of dairy manure has been investigated at several organic loading rates. Two identical UASB reactors were employed. The biomass of one UASB reactor (FBR) had previously been treated with a cationic polyacrylamide, the other reactor was operated as a control reactor (CR). At 3 and 2 days of HRT both reactors functioned similarly, but at 1.5 days HRT some differences were observed between both effluents. Mean COD(T) removal percentages were 83.4% and 76.5%; COD(VFA) values in effluents were 977 and 2682 mg l(-1) for the FBR and the CR respectively. The VSS initial value in both reactors was 25.66 g VSS, whereas after the experiment the quantities were 31.83 g VSS in the FBR and 23.18 g VSS in the CR reactors. Polymer addition resulted in a higher degree of biomass retention and better performance in the FBR reactor.     

Application of polyethylene glycol immobilized Clostridium sp. LS2 for continuous hydrogen production from palm oil mill effluent in upflow anaerobic sludge blanket reactor

A novel polyethylene glycol (PEG) gel was fabricated and used as a carrier to immobilize Clostridium sp. LS2 for continuous hydrogen production in an upflow anaerobic sludge blanket (UASB) reactor. Palm oil mill effluent (POME) was used as the substrate carbon source. The optimal amount of PEG-immobilized cells for anaerobic hydrogen production was 12% (w/v) in the UASB reactor. The UASB reactor containing immobilized cells was operated at varying hydraulic retention times (HRT) that ranged from 24 to 6 h at 3.3 g chemical oxygen demand (COD)/L/h organic loading rate (OLR), or at OLRs that ranged from 1.6 to 6.6 at 12 h HRT. The best volumetric hydrogen production rate of 336 mL H₂/L/h (or 15.0 mmol/L/h) with a hydrogen yield of 0.35 L H₂/g COD_removed was obtained at a HRT of 12 h and an OLR of 5.0 g COD/L/h. The average hydrogen content of biogas and COD reduction were 52% and 62%, respectively. The major soluble metabolites during hydrogen fermentation were butyric acid followed by acetic acid. It is concluded that the PEG-immobilized cell system developed in this work has great potential for continuous hydrogen production from real wastewater (POME) using the UASB reactor.     

High rate biological treatment of sulfate-rich wastewater in an acetate-fed EGSB reactor

An expanded granular sludge bed reactor, inoculated with acclimated sulfidogenic granular sludge, was operated at 33 °C and fed with acetic acid as COD source and sulfate as electron acceptor. The bioreactor had a sulfate conversion efficiency of 80–90% at a high sulfate loading rate of 10.4 g SO₄ ^2--S/l.d after only 60 days of start-up. This was achieved by implementing a dual operational strategy. Firstly acetic acid was dosed near stoichiometry (COD over sulfur ratio = 2.0 to 2.2) which allowed almost complete sulfate removal. Secondly the pH in the bioreactor was kept slightly alkaline (7.9 ± 0.1) which limited the concentration of the inhibitory undissociated hydrogen sulfide H₂S (pK_a = 7). This allowed the acetotrophic sulfate reducing bacteria to predominate throughout the long term experiment. The limitations of the EGSB technology with respect to the sulfate conversion rate appeared to be related to the biomass wash-out and granule deterioration occurring at superficial upflow velocities above 10 m/h. Increasing the recirculation flow caused a drop in the sulfate reduction rate and efficiency, an increase of the suspended sludge fraction and a considerable loss of biomass into the effluent, yielding bare mainly inorganic granules. Elemental analysis revealed that a considerable amount of the granular sludge dry matter at the end of the experiment, at an upflow velocity of 20 m/h, consisted of calcium (32%), mainly in the form of carbonate deposits, while organic matter only represented 7%.     

Long-term competition between sulfate reducing and methanogenic bacteria in UASB reactors treating volatile fatty acids

The competition between acetate utilizing methane-producing bacteria (MB) and sulfate-reducing bacteria (SRB) was studied in mesophilic (30 degrees C) upflow anaerobic sludge bed (UASB) reactors (upward velocity 1 m h-1; pH 8) treating volatile fatty acids and sulfate. The UASB reactors treated a VFA mixture (with an acetate:propionate:butyrate ratio of 5:3:2 on COD basis) or acetate as the sole substrate at different COD:sulfate ratios. The outcome of the competition was evaluated in terms of conversion rates and specific methanogenic and sulfidogenic activities. The COD:sulfate ratio was a key factor in the partitioning of acetate utilization between MB and SRB. In excess of sulfate (COD:sulfate ratio lower than 0.67), SRB became predominant over MB after prolonged reactor operation: 250 and 400 days were required to increase the amount of acetate used by SRB from 50 to 90% in the reactor treating, respectively, the VFA mixture or acetate as the sole substrate. The competition for acetate was further studied by dynamic simulations using a mathematical model based on the Monod kinetic parameters of acetate utilizing SRB and MB. The simulations confirmed the long term nature of the competition between these acetotrophs. A high reactor pH (+/-8), a short solid retention time (<150 days), and the presence of a substantial SRB population in the inoculum may considerably reduce the time required for acetate-utilising SRB to outcompete MB.     

Sulfate reduction and trichloroethylene biodegradation by a marine microbial community from hydrothermal vents sediments

Sulfate reduction (SR) and trichloroethylene (TCE) biodegradation at two different temperatures (37 and 70 °C) were investigated in enrichment cultures prepared with two different samples of sediments collected from hydrothermal vents. The unadapted sediments were incubated with sulfate (4 g L⁻¹) as the electron acceptor before TCE addition to enrich them in biomass and to establish a constant sulfate reduction (SR, 87% sulfate conversion and specific H₂S concentration of 90.81 ± 8.19 mg H₂S g VSS⁻¹), afterwards TCE was added at an initial concentration of 300 ??mol L⁻¹. The best results for TCE biodegradation were obtained at 37 °C. At this temperature, SR was up to 92%, whereas TCE biodegradation reached 75% and ethane was detected as the main degradation product. Under thermophilic conditions (70 °C) TCE biodegradation reached up to approximately 60% and the SR was 30% in 30 days of incubation with the chlorinated solvent. Along with these results, the 16S rDNA analysis from samples at 37 °C showed the presence of bacteria belonging to the genera: Clostridium, Bacillus and Desulfuromonas. The overall results on TCE degradation and SR suggest that cometabolic TCE degradation is carried out by sulfate or sulfur reducers and fermentative bacteria at mesophilic conditions.     

Comparison of CSTR and UASB reactor configuration for the treatment of sulfate rich wastewaters under acidifying conditions

The effects of lowering the operational pH from 6 to 5 on mesophilic (30 °C) sulfate reduction during the acidification of sucrose at an organic loading rate of 5 gCOD (l_reactor d)⁻¹ and at a COD/SO₄²⁻ ratio of 4 were evaluated in a CSTR and in a UASB reactor. The HRT was 24 h and 10 h, respectively. Acidification was complete in both reactors at pH 6 and the lowering of the operational pH to 5 did not affect the acidification efficiency in the CSTR but decreased the acidification efficiency of the UASB to 72%. The decrease to pH 5 caused an increase in the effluent butyrate and ethanol concentrations in both reactors. Lowering the pH from 6 to 5 caused a decrease in sulfate reduction efficiencies in both reactors, from 43% to 25% in the CSTR and from 95% to 34% in the UASB reactor. The acidification and sulfate reduction efficiencies at pH 5 could be increased to 94% and 67%, respectively, by increasing the HRT of the UASB reactor to 24 h.     

Assessment of a UASB reactor with high ammonia concentrations: Effect of zeolite addition on process performance

The UASB process for wastewater treatment has been extensively studied, but the use of zeolite to improve UASB reactor performance has rarely been explored. In this study, a UASB reactor modified with natural zeolite operating at high nitrogen concentrations (0.5, 0.7 and 1 g/L) was evaluated. Two laboratory bioreactors, one with zeolite and one without, were operated at ambient temperatures ranging between 18 °C and 21 °C. The experimental phase had a start-up period of 21 days. In the reactor with zeolite, the pH was found to be between 7.9 and 9.1, with a COD removal efficiency of about 60% after 80 days of operation at ammonia concentrations of between 0.229 and 0.429 g/L in the effluent. In the reactor without zeolite, the pH was between 8.3 and 9.3, and the COD removal efficiency was about 40% at ammonia concentrations between 0.244 and 0.535 g/L in the effluent. The addition of zeolite also decreased the volatile suspended solids (VSS) concentration in the effluent, generating a biomass with larger granules and higher settling rates as compared to a UASB reactor without zeolite. Taking the lower ammonia concentration, the higher COD removal and the improved granulation into account, it can be concluded that natural zeolite positively influenced the behavior and performance of the UASB reactor operating with high nitrogen concentrations.     

Comparison of CSTR and UASB reactor configuration for the treatment of sulfate rich wastewaters under acidifying conditions

The effects of lowering the operational pH from 6 to 5 on mesophilic (30 °C) sulfate reduction during the acidification of sucrose at an organic loading rate of 5 gCOD (l_reactor d)⁻¹ and at a COD/SO₄²⁻ ratio of 4 were evaluated in a CSTR and in a UASB reactor. The HRT was 24 h and 10 h, respectively. Acidification was complete in both reactors at pH 6 and the lowering of the operational pH to 5 did not affect the acidification efficiency in the CSTR but decreased the acidification efficiency of the UASB to 72%. The decrease to pH 5 caused an increase in the effluent butyrate and ethanol concentrations in both reactors. Lowering the pH from 6 to 5 caused a decrease in sulfate reduction efficiencies in both reactors, from 43% to 25% in the CSTR and from 95% to 34% in the UASB reactor. The acidification and sulfate reduction efficiencies at pH 5 could be increased to 94% and 67%, respectively, by increasing the HRT of the UASB reactor to 24 h.     

Treatment of domestic wastewater in an up-flow anaerobic sludge blanket reactor followed by moving bed biofilm reactor

The performance of a laboratory-scale sewage treatment system composed of an up-flow anaerobic sludge blanket (UASB) reactor and a moving bed biofilm reactor (MBBR) at a temperature of (22–35 °C) was evaluated. The entire treatment system was operated at different hydraulic retention times (HRT’s) of 13.3, 10 and 5.0 h. An overall reduction of 80–86% for COD_total; 51–73% for COD_colloidal and 20–55% for COD_soluble was found at a total HRT of 5–10 h, respectively. By prolonging the HRT to 13.3 h, the removal efficiencies of COD_total, COD_colloidal and COD_soluble increased up to 92, 89 and 80%, respectively. However, the removal efficiency of COD_suspended in the combined system remained unaffected when increasing the total HRT from 5 to 10 h and from 10 to 13.3 h. This indicates that, the removal of COD_suspended was independent on the imposed HRT. Ammonia-nitrogen removal in MBBR treating UASB reactor effluent was significantly influenced by organic loading rate (OLR). 62% of ammonia was eliminated at OLR of 4.6 g COD m⁻² day⁻¹. The removal efficiency was decreased by a value of 34 and 43% at a higher OLR’s of 7.4 and 17.8 g COD m⁻² day⁻¹, respectively. The mean overall residual counts of faecal coliform in the final effluent were 8.9 × 10⁴ MPN per 100 ml at a HRT of 13.3 h, 4.9 × 10⁵ MPN per 100 ml at a HRT of 10 h and 9.4 × 10⁵ MPN per 100 ml at a HRT of 5.0 h, corresponding to overall log₁₀ reduction of 2.3, 1.4 and 0.7, respectively. The discharged sludge from UASB–MBBR exerts an excellent settling property. Moreover, the mean value of the net sludge yield was only 6% in UASB reactor and 7% in the MBBR of the total influent COD at a total HRT of 13.3 h. Accordingly, the use of the combined UASB–MBBR system for sewage treatment is recommended at a total HRT of 13.3 h.     

Solids hydrolysis and accumulation in a hybrid anaerobic digester-constructed wetlands system

The properties and behaviour of solids retained in a pilot plant constituted of an up-flow anaerobic sludge blanket (UASB) reactor and two constructed wetlands (CWs) were monitored over a 3-year period. The UASB (25.5 m³) was fed with raw municipal wastewater at a flow rate of 61–112 m³ d^?1 and a volumetric loading rate (VLR) of 0.75–1.70 kg TCOD m^?3 d^?1. The CWs (75 m² each) were operated in series and received a fraction (17–20 m³ d^?1) of the UASB effluent. The applied surface loading rates (SLR) were in the range of 3800–8700 g TCOD m^?2 d^?1 (UASB) and 11–15 g BOD₅ m^?2 d^?1 (CWs). The overall system removed 95% TSS, 85% TCOD and 87% BOD₅ on average. For influent VSS, the UASB removed 72.1% and gave a hydrolysis of 63.5%, while the average surplus sludge generation was 8.7%. Over the 3-year period, TSS and VSS accumulated in the CWs at rates of 1.07 and 0.56 kg m^?2 year^?1, respectively. The aerobic biodegradability of the accumulated solids ranged from 23 to 92 mg O₂ g VSS^?1 d^?1 and increased downstream in the CWs. About 59% of the VSS that entered the CWs was removed by hydrolysis, while 24% accumulated on granular media. These low solids accumulation rates were especially remarkable considering the high COD and BOD₅ loading rates applied. The system lay-out appear to be promising in terms of preventing clogging.     

Comparative anaerobic treatment of wastewater from pharmaceutical,brewery, paper and amino acid producing industries

This study concerned the anaerobic treatment of five different industrial wastewaters with a diverse and complex chemical composition. The kinetics of biotransformation of this wastewater at different chemical oxygen demand (COD) were studied in a batch reactor. Wastewater from an amino acid producing industry (Fermex) and from a tank that received several types of wastewaters (collector) contained 0.83 g l⁻¹ and 0.085 g l⁻¹ sulfate, respectively. During the study period of 20 days, methane formation was observed in all types of wastewaters. Studies on COD biodegradation showed the reaction velocity was higher for Fermex wastewater and lower for collector wastewater, with values of 0.0022 h⁻¹ and 0.0011 h⁻¹, respectively. A lower methanogenic activity of 0.163 g CH₄ day⁻¹ g⁻¹ volatile suspended solids (VSS) and 0.20 g CH₄ day⁻¹ g⁻¹ VSS, respectively, was observed for paper producing and brewery wastewater. Adapted granular sludge showed the best biodegradation of COD during the 20-day period. The sulfate-reducing activity in pharmaceutical and collector wastewater was studied. A positive effect of sulfate-reducing activity on methanogenic activity was noted for both types of wastewaters, both of which contained sulfate ions. All reactions of methane generation for the tested industrial wastewaters were first-order. The results of this study suggest that the tested wastewaters are amenable to anaerobic treatment.

     

Kinetic Modelling and Characterization of Microbial Community Present in a Full-Scale UASB Reactor Treating Brewery Effluent

The performance of a full-scale upflow anaerobic sludge blanket (UASB) reactor treating brewery wastewater was investigated by microbial analysis and kinetic modelling. The microbial community present in the granular sludge was detected using fluorescent in situ hybridization (FISH) and further confirmed using polymerase chain reaction. A group of 16S rRNA based fluorescent probes and primers targeting Archaea and Eubacteria were selected for microbial analysis. FISH results indicated the presence and dominance of a significant amount of Eubacteria and diverse group of methanogenic Archaea belonging to the order Methanococcales, Methanobacteriales, and Methanomicrobiales within in the UASB reactor. The influent brewery wastewater had a relatively high amount of volatile fatty acids chemical oxygen demand (COD), 2005 mg/l and the final COD concentration of the reactor was 457 mg/l. The biogas analysis showed 60–69 % of methane, confirming the presence and activities of methanogens within the reactor. Biokinetics of the degradable organic substrate present in the brewery wastewater was further explored using Stover and Kincannon kinetic model, with the aim of predicting the final effluent quality. The maximum utilization rate constant U _max and the saturation constant (K _B) in the model were estimated as 18.51 and 13.64 g/l/day, respectively. The model showed an excellent fit between the predicted and the observed effluent COD concentrations. Applicability of this model to predict the effluent quality of the UASB reactor treating brewery wastewater was evident from the regression analysis (R ²?=?0.957) which could be used for optimizing the reactor performance.     

Performance evaluation and kinetic modeling of the start-up of a UASB reactor treating municipal wastewater at low temperature

A kinetic modeling-based study was carried out to evaluate the start-up performance of a 10-L up-flow anaerobic sludge blanket (UASB) reactor treating municipal wastewater under different organic and hydraulic loading conditions. The reactor was operated for 105 days (around 4 months) below 20 °C and with three different hydraulic retention times of 24, 12 and 5 h. Imposed volumetric organic loading rates (OLR) ranged from 0.57 (±0.05) to 11.78 (±0.85) kg TCOD/m³-day. Although relatively high incoming volumetric OLR values were employed to the system, the UASB reactor demonstrated a favorable performance on the anaerobic treatability of municipal wastewater, and no process failure was recorded in the start-up stage. On the basis of experimental results, the modified Stover–Kincannon model was successfully applied to define the start-up kinetics with a very high value of the correlation coefficient (R = 0.9729). Maximum substrate utilization rate constant and saturation constant of the modified Stover–Kincannon model were determined as U _max = 1.996 g/L-day and K _B = 1.536 g/L-day, respectively.     

Microbial sulfate reduction at low (8 °C) temperature using waste sludge as a carbon and seed source

Biological treatment of sulfate and metal-containing wastewater (such as acid mine drainage) is a viable option due to lower cost and better sludge quality compared to conventional chemical treatment. Although several substrates can be used as carbon source, a low-cost substrate is required for large scale applications. This study was conducted to investigate the suitability of waste sludge as a carbon and seed source for sulfate reduction at 8 °C in batch bioassays. Around 7 mmol of sulfate was reduced when the waste sludge mixture (WS) (6700 mg SS l^?1) from primary and secondary settling tank was supplemented as a carbon and seed source. However, only 1.6 mmol of sulfate was reduced with anaerobic digester effluent (ADS) (5300 mg SS l^?1). The produced H₂S from 1 g VSS l^?1 WS and ADS oxidation can theoretically precipitate around 90 and 35 mg Fe²⁺, respectively. Both WS and ADS oxidized ethanol to acetate at similar rates. It appears that WS is a good candidate for carbon and start-up seed source of sulfate reduction at 8 °C, whereas sulfidogenic acetate oxidation was the limiting step. Denaturing gradient gel electrophoresis (DGGE) analysis of 16S rRNA genes showed that both sludge sources contain Desulfomicrobium apsheronum strain.