Particle-by-particle quantification of protein adsorption onto poly(ethylene glycol) grafted surfaces

The use and advantage of flow cytometry as a particle-by-particle, low sampling volume, high-throughput screening technique for quantitatively examining the non-specific adsorption of proteins onto surfaces is presented. The adsorption of three proteins: bovine serum albumin (BSA), immunoglobulin gamma (IgG) and protein G, incubated at room temperature for 2 h onto organosilica particles modified with poly(ethylene glycol) (PEG) of increasing MW (2000, 3400, 6000, 10,000 and 20,000 g mol(-1)) and grafted amounts (0.14-1.4 mg m(-2)) was investigated as a model system. Each protein exhibited Langmuir-like, high affinity monolayer limited adsorption on unmodified particles with the proteins reaching surface saturation at 1.8, 4.0 and 2.5 mg m(-2) for BSA, IgG and protein G, respectively. Protein adsorption on PEG-modified surfaces was found to decrease with increasing amounts of grafted polymer. PEG grafting amounts >0.6 mg m(-2) effectively prevented the adsorption of the larger two proteins (BSA and IgG) while a PEG grafting amount >1.3 mg m(-2) was required to prevent the adsorption of the smaller protein G.     

Minimization of protein adsorption on poly(vinylidene fluoride)

Surfaces covered with polyethylene glycol (PEG) have been shown to be biocompatible because PEG yields nonimmunogenicity, nonantigenicity and protein rejection. To produce a biocompatible surface coating, we have developed a method for grafting PEG onto modified poly(vinylidene fluoride) (PVDF) films. The first step was to create carboxy groups on the PVDF surface following covalente coupling of polyethylenimine (PEI) to achieve high density of amino groups. These surface amines were reacted with formyl-terminated PEG's with various molecular weight. The modified PVDF surface was characterized by means of static contact angle measurements, infrared (IR) spectroscopy and X-ray photoelectron spectroscopy (XPS). The influence of the chain length on lysozyme repellence was investigated by means of surface-MALDI-Tof mass spectrometry (Surface-MALDI-Tof-MS). Lysozyme adsorption was significantly suppressed on the PEG 5000 modified PVDF surface.     

Improved performances of intraocular lenses by poly(ethylene glycol) chemical coatings

Cataract surgery is a routine ophthalmologic intervention resulting in replacement of the opacified natural lens by a polymeric intraocular lens (IOL). A main postoperative complication, as a result of protein adsorption and lens epithelial cell (LEC) adhesion, growth, and proliferation, is the secondary cataract, referred to as posterior capsular opacification (PCO). To avoid PCO formation, a poly(ethylene glycol) (PEG) chemical coating was created on the surface of hydrogel IOLs. Attenuated total reflectance Fourier transform infrared spectroscopy, "captive bubble" and "water droplet" contact angle measurements, and atomic force microscopy analyses proved the covalent grafting of the PEG chains on the IOL surface while keeping unchanged the optical properties of the initial material. A strong decrease of protein adsorption and cell adhesion depending on the molar mass of the grafted PEG (1100, 2000, and 5000 g/mol) was observed by performing the relevant in vitro tests with green fluorescent protein and LECs, respectively. Thus, the study provides a facile method for developing materials with nonfouling properties, particularly IOLs.     

Synthesis and characterization of novel poly[(organo)phosphazenes] with cell-adhesive side groups

There is a need to develop new scaffold materials with controlled surface properties for tissue engineering applications. For that purpose novel biodegradable poly[(organo)phosphazenes] were synthesized. A cell-binding molecule, galactose, was introduced via a spacer, either 6-aminohexanol (AH) or poly(ethylene glycol) (PEG; M(w) = 3400). Some polymers were substituted with an additional PEG chain of different molecular weights (M(w) = 750 or 5000). The polyphosphazene derivatives were characterized by 1H NMR. T(g) and T(m) were determined using differential scanning calorimetry. A detailed surface analysis of the polymers using X-ray photoelectron spectroscopy (XPS), secondary ion mass spectroscopy (SIMS), and dynamic contact angle (DCA) measurements was performed. Typical backbone and side chain fragments were detected by SIMS and confirmed the polymer composition. Compared to that of the reference polymer (having only amino acid ester side groups), an increased value of the specific ether carbon groups from PEG confirmed the enrichment of PEG at the surface of PEG-Gal polymers. However, the values were lower than expected. DCA studies showed that the galactose moieties were present at the surface after exposure to an aqueous environment. XPS results confirmed the similarity between experimental and theoretical values for the AH-Gal polymers. This indicated the presence of galactose moieties at the surface, which was confirmed by the DCA data because the contact angles were low compared to those of the other polymers.     

Spatially well-defined binary brushes of poly(ethylene glycol)s for micropatterning of active proteins on anti-fouling surfaces

We report a novel method for micropatterning of active proteins on anti-fouling surfaces via spatially well-defined and dense binary poly(ethylene glycol)s (PEGs) brushes with controllable protein-docking sites. Binary brushes of poly(poly(ethylene glycol) methacrylate-co-poly(ethylene glycol)methyl ether methacrylate), or P(PEGMA-co-PEGMEMA), and poly(poly(ethylene glycol)methyl ether methacrylate), or P(PEGMEMA), were prepared via consecutive surface-initiated atom transfer radical polymerizations (SI-ATRPs) from a resist-micropatterned Si(100) wafer surface. The terminal hydroxyl groups on the side chains of PEGMA units in the P(PEGMA-co-PEGMEMA) microdomains were activated directly by 1,1'-carbonyldiimidazole (CDI) for the covalent coupling of human immunoglobulin (IgG) (as a model active protein). The resulting IgG-coupled PEG microdomains interact only and specifically with target anti-IgG, while the other PEG microregions effectively prevent specific and non-specific protein fouling. When extended to other active biomolecules, microarrays for specific and non-specific analyte interactions with a high signal-to-noise ratio could be readily tailored.     

Physiochemical properties of low and high molecular weight poly(ethylene glycol)-grafted poly(ethylene imine) copolymers and their complexes with oligonucleotides

Inefficient delivery of antisense oligonucleotides (AOs) to target cell nuclei remains as the foremost limitation to their usefulness. Copolymers of cationic poly(ethylene imine) (PEI) and poly(ethylene glycol) (PEG) have been well-studied for delivery of plasmids. However, the properties of PEG-PEI-AO polyplexes have not been comprehensively investigated. Therefore, we synthesized a series of PEG-PEI copolymers and evaluated their physiochemical properties alone and when complexed with AO. The M(w) of PEG was found to be the main determinant of polyplex size, via its influence on particle aggregation. DLS measurements showed that when PEG5000 was grafted to PEI2K and PEI25K, polyplex diameters were extremely small (range 10-90 nm) with minimal aggregation. In contrast, when PEG550 was grafted to PEI2K and PEI25K, polyplexes appeared as much larger aggregates (approximately 250 nm). As expected, the surface charge (zeta potential) was higher for polyplexes containing PEI25K than those containing PEI2K, but decreased with increased levels of PEG grafting. Surprisingly, within the physiological range (pH 7.5-5), the buffering capacity of all copolymers was nearly equivalent to that of unsubstituted PEI2K or PEI25K, and was barely influenced by PEGylation. The stability of polyplexes was evaluated using a heparin polyanion competition assay. Unexpectedly, polyplexes containing PEI2K showed stability equal to or greater than that of PEI25K polyplexes. The level of PEG grafting also had a dramatic effect on polyplex stability. The relationships established between molecular formulations and polyplex size, aggregation, surface charge, and stability should provide a useful guide for future studies aimed at optimizing polymer-mediated AO delivery in cell and animal studies. A summary of the relationships between polyplex structures and recent studies of their transfection capacity is provided.     

Poly(ethylene glycol) amphiphile adsorption and liposome partition

Surface localized poly(ethylene glycol) (PEG) amphiphiles of type C_16:0-EO₁₅₁ and C_18:2-EO₁₅₁ were studied via ellipsometry at macroscopic, flat methylated silica (MeSi), phosphatidic acid (PA), and phosphatidylcholine (PC) surfaces. At these surfaces the amphiphiles adsorb similarly, in a non-cooperative manner, achieving a plateau (≈0.1 PEG chains/nm²) well below amphiphile critical micelle concentration (CMC). The resultant PEG-enriched layers were 10–15 nm thick, with a polymer concentration (≈0.07 g/cm³) greater than the PEG-enriched phase of many dextran, PEG aqueous two-phase systems. PEG-amphiphile adsorption (mg/m²) at hydrophobic and phospholipid flat surfaces correlated with changes in the partition (log K) of PC liposomes in such two-phase systems. PEG-amphiphile adsorption at macroscopic surfaces appears to represent a balance between hydrophobic attraction and repulsive intra-chain interactions which promote chain elongation normal to the surface.     

Protein fouling resistant membrane prepared by amphiphilic pegylated polyethersulfone

A mild and facile grafting of poly(ether glycol) methyl ether methacrylate (PEGMA) monomers onto polyethersulfone (PES) was carried out. Then, the PES-g-PEGMA membranes with integrally anisotropic morphology were fabricated through the coupling of non-solvent induced phase inversion and surface segregation. Compared with PES control membrane, the surface hydrophilicity of PES-g-PEGMA membranes was remarkably enhanced due to the drastic enrichment of poly(ethylene glycol) (PEG) segments on the membrane surface; protein adsorption was significantly inhibited due to the hydrogen bonding interactions between hydrophilic groups and water molecules. Ultrafiltration experiments were used to assess the permeability and protein fouling resistance of the PES-g-PEGMA membranes. It was found that the PES-g-PEGMA membranes with higher surface coverage of PEG segments displayed stronger antibiofouling property. Moreover, the stable antibiofouling property for PES-g-PEGMA membranes was acquired due to covalent bonding interactions between hydrophilic PEGMA side chains and PES main chains.     

Synthesis, patterning and applications of star-shaped poly(ethylene glycol) biofunctionalized surfaces

Poly(ethylene) glycol (PEG) is an excellent material to modify surfaces to resist non-specific protein adsorption. Linear PEG has been extensively studied both theoretically and experimentally and it has been found that resistance of PEG-coated surfaces to protein adsorption depends mainly on the molecular weight of the polymer and the surface grafting density. End-functionalized star-shaped PEGs allow for interpolymer crosslinking to form a dense layer. An excellent example of such a system consists of a 6-arm PEG/PPG (4 : 1) star polymer functionalized with isocyanate using IPDI. The end functionalization may be further biofunctionalized to recognize specific biomolecules such as streptavidin, His-tagged proteins, amino-terminated oligonucleotides and cell receptors. This functionalization may be patterned into specific geometries using stamping techniques or randomly distributed by statistical reaction of the end group with the biofunctional molecule in solution. The surface preparation uses simple spin-, dip- or spray-coating and produces smooth layers with low background fluorescence. These properties, together with the advantageous chemical properties of PEG, render the surfaces ideal for immobilizing proteins on surfaces with detection limits down to the single molecule level. Proteins immobilized on such surfaces are able to maintain their folded, functional form and are able to completely refold if temporarily exposed to denaturing conditions. Immobilized enzyme molecules were able to perform their function with the same activity as the enzyme in solution. Future directions of using surfaces coated with such crosslinked star polymers in highly sensitive and robust biotechnology applications will be discussed.     

Functionalised inherently conducting polymers as low biofouling materials

Diatoms are a major component of microbial biofouling layers that develop on man-made surfaces placed in aquatic environments, resulting in significant economic and environmental impacts. This paper describes surface functionalisation of the inherently conducting polymers (ICPs) polypyrrole (PPy) and polyaniline (PANI) with poly(ethylene glycol) (PEG) and their efficacy as fouling resistant materials. Their ability to resist interactions with the model protein bovine serum albumin (BSA) was tested using a quartz crystal microbalance with dissipation monitoring (QCM-D). The capacity of the ICP-PEG materials to prevent settlement and colonisation of the fouling diatom Amphora coffeaeformis (Cleve) was also assayed. Variations were demonstrated in the dopants used during ICP polymerisation, along with the PEG molecular weight, and the ICP-PEG reaction conditions, all playing a role in guiding the eventual fouling resistant properties of the materials. Optimised ICP-PEG materials resulted in a significant reduction in BSA adsorption, and > 98% reduction in diatom adhesion.     

In-situ formation of biodegradable hydrogels by stereocomplexation of PEG-(PLLA)8 and PEG-(PDLA)8 star block copolymers

Eight-arm poly(ethylene glycol)-poly(L-lactide), PEG-(PLLA)(8), and poly(ethylene glycol)-poly(D-lactide), PEG-(PDLA)(8), star block copolymers were synthesized by ring-opening polymerization of either L-lactide or D-lactide at room temperature in the presence of a single-site ethylzinc complex and 8-arm PEG (M(n) = 21.8 x 10(3) or 43.5 x 10(3)) as a catalyst and initiator, respectively. High lactide conversions (>95%) and well-defined copolymers with PLLA or PDLA blocks of the desired molecular weights were obtained. Star block copolymers were water-soluble when the number of lactyl units per poly(lactide) (PLA) block did not exceed 14 and 17 for PEG21800-(PLA)(8) and PEG43500-(PLA)(8), respectively. PEG-(PLA)(8) stereocomplexed hydrogels were prepared by mixing aqueous solutions with equimolar amounts of PEG-(PLLA)(8) and PEG-(PDLA)(8) in a polymer concentration range of 5-25 w/v % for PEG21800-(PLA)(8) star block copolymers and of 6-8 w/v % for PEG43500-(PLA)(8) star block copolymers. The gelation is driven by stereocomplexation of the PLLA and PDLA blocks, as confirmed by wide-angle X-ray scattering experiments. The stereocomplexed hydrogels were stable in a range from 10 to 70 degrees C, depending on their aqueous concentration and the PLA block length. Stereocomplexed hydrogels at 10 w/v % polymer concentration showed larger hydrophilic and hydrophobic domains as compared to 10 w/v % single enantiomer solutions, as determined by cryo-TEM. Correspondingly, dynamic light scattering showed that 1 w/v % solutions containing both PEG-(PLLA)(8) and PEG-(PDLA)(8) have larger "micelles" as compared to 1 w/v % single enantiomer solutions. With increasing polymer concentration and PLLA and PDLA block length, the storage modulus of the stereocomplexed hydrogels increases and the gelation time decreases. Stereocomplexed hydrogels with high storage moduli (up to 14 kPa) could be obtained at 37 degrees C in PBS. These stereocomplexed hydrogels are promising for use in biomedical applications, including drug delivery and tissue engineering, because they are biodegradable and the in-situ formation allows for easy immobilization of drugs and cells.     

Ultralow fouling polyacrylamide on gold surfaces via surface-initiated atom transfer radical polymerization

In this work, polyacrylamide is investigated as an ultralow fouling surface coating to highly resist protein adsorption, cell adhesion, and bacterial attachment. Polyacrylamide was grafted on gold surfaces via surface-initiated atom transfer radical polymerization (ATRP). Protein adsorption from a wide range of biological media, including single protein solutions of fibrinogen, bovine serum albumin, and lysozyme, dilute and undiluted human blood serum, and dilute and undiluted human blood plasma, was studied by surface plasmon resonance (SPR). Dependence of the protein resistance on polyacrylamide film thickness was examined. With the optimal film thickness, the adsorption amount of all three single proteins on polyacrylamide-grafted surfaces was <3 pg/mm(2), close to the detection limit of SPR. The average nonspecific adsorptions from 10% plasma, 10% serum, 100% plasma, and 100% serum onto the polyacrylamide-grafted surfaces were 5, 6.5, 17, and 28 pg/mm(2), respectively, comparable (if not better) than the adsorption levels on poly(ethylene glycol) (PEG) and zwitterionic poly(sulfobetaine methacrylate) surfaces, the best antifouling materials known to date. The polyacrylamide-grafted surfaces were also shown strongly resistant to adhesion from bovine aortic endothelial cells and two bacterial species, Gram-positive Staphylococcus epidermidis ( S. epidermidis ) and Gram-negative Pseudomonas aeruginosa ( P. aeruginosa ). Strong hydrogen bond with water is considered the key attribute for the ultralow fouling properties of polyacrylamide. This is the first work to graft gold surfaces with polyacrylamide brushes via ATRP to achieve ultralow fouling surfaces, demonstrating that polyacrylamide is a promising alternative to traditional PEG-based antifouling materials.     

Evaluation of liquid chromatography column retentivity using macromolecular probes. IV. Poly(ethylene glycol) bonded phase

Interaction properties of the novel HPLC silica gel-poly(ethylene glycol) (PEG) bonded phase were evaluated applying polymeric test substances, viz. polystyrenes, poly(methyl methacrylate)s, poly(ethylene oxide)s and poly(2-vinyl pyridine)s, and eluents of different polarities. Silanols on the silica gel surface are well shielded by the PEG phase, and silanophilic adsorption of macromolecules is suppressed in comparison with most silica C(18) bonded phases. The adsorption of solutes on the -OH groups of the PEG phase seems to be low as well. The partition of macromolecules in favor of the PEG phase is inferior to that observed in case of the silica C(18) phases. The volume of the PEG bonded phase is small and it is supposed that the PEG chains assume flat conformation on the silica gel surface.     

Synthesis and biopharmaceutical characterisation of new poly(hydroxyethylaspartamide) copolymers as drug carriers.

Four new poly(hydroxyethylaspartamide)-based copolymers bearing (a) poly(ethylene glycol) 2000, (b) poly(ethylene glycol) 5000, (c) poly(ethylene glycol) 2000 and hexadecylalkyl, (d) poly(ethylene glycol) 5000 and hexadecylalkyle, as pendant groups were synthesised. The copolymers were obtained by partial aminolysis of polysuccinimide with poly(ethylene glycol) and hexadecylalkyl amino derivatives followed by reaction with ethanolamine. Naked polyhydroxyaspartamide was obtained by polysuccinimide reaction with ethanolamine. The nuclear magnetic resonance, infrared, light scattering and elemental analysis allowed for the extensive physico-chemical characterisation of the carriers. The molecular mass of all the polymers was in the range of 27000-34000 Da, and the polydispersivity was in the range of 1.5-1.7. By intravenous injection to mice bearing a solid tumour, all the polymeric carriers displayed a bi-compartmental pharmacokinetic behaviour. Both the poly(ethylene glycol) and the hexadecylalkyle conjugation prolonged and enhanced the distribution phase of poly(hydroxyethylaspartamide). The poly(ethylene glycol) conjugation was found to promote the carrier elimination by kidney ultrafiltration and to prevent partially the accumulation in the spleen and in the liver. The poly(ethylene glycol)/hexadecylalkyle conjugates localised preferentially in the liver were over 30% of the dose/g of tissue was determined after 144 h from administration. In the tumour all the polymers displayed a relevant accumulation that significantly increased throughout the time to reach high concentrations after 24 h. In particular, the poly(ethylene glycol)/hexadecylalkyle conjugates achieved a concentration of 15-25% of the dose/g of tissue after 24 h from administration that was maintained up to 144 h.     

Contact angle, WAXS, and SAXS analysis of poly(beta-hydroxybutyrate) and poly(ethylene glycol) block copolymers obtained via Azotobacter vinelandii UWD

This study investigated and correlated physical properties and cell interactions of copolymers obtained by a poly(ethylene glycol) (PEG)-modulated fermentation of Azotobacter vinelandii UWD. PEGs with molecular weights of 400 and 3400 Da and di(ethylene glycol) (DEG) were used to modulate the bacterial synthesis of poly(beta-hydroxybutyrate) (PHB). The PHB crystallinity was determined by wide-angle X-ray scattering (WAXS). Small-angle X-ray scattering (SAXS) showed that lamellar distances decreased between the PHB and the PHB modulated with PEG or DEG. Furthermore, the contact angle of water on the PHB/PEG polymer surfaces decreased when compared to that of PHB. The significant decrease of the contact angle and corresponding increase in surface tension, as well as significant decrease in cell adhesion, suggest the presence of hydrophilic PEG and DEG within the hydrophobic surface.     

A high-density poly(ethylene glycol) polymer brush for immobilization on glass-type surfaces.

Label-free heterogeneous phase detection critically depends on the properties of the interfacial layer. We have obtained high-density monomolecular poly(ethylene glycol) (PEG) layers by solvent-free coupling of homo-bifunctional PEGs (2,000 g/mol) at 75 degrees C to silica surfaces silanized with glycidyloxipropyltrimethoxysilane (GOPTS). Characterization by ellipsometry and contact angles revealed that PEG layers up to 3.4 ng/mm2 with low roughness and flexibility were obtained. Specific and non-specific binding at these PEG surfaces was monitored by reflectometric interference spectroscopy (RIfS). No significant non-specific adsorption upon incubation of 1 mg/ml ovalbumin was detectable (< 10 pg/mm2), and 150 pg/mm2 upon incubation of 10% calf serum, less than 10% of the amount adsorbed to the solely silanized surfaces. The terminal functional groups of the PEG layers were utilized to couple ligands and a protein. Specific protein interaction with these immobilized compounds was detected with saturation loadings in the range of protein monolayers (2-4 ng/mm2). The excellent functional properties, the high stability of the layers, the generic and practical coupling procedure and the versatility for immobilizing compounds of very different functionality make these PEG layers very attractive for application in label-free detection with silica or metal-oxide based transducers.     

Zwitterionic polymers exhibiting high resistance to nonspecific protein adsorption from human serum and plasma

This study examined six different polymer and self-assembled monolayer (SAM) surface modifications for their interactions with human serum and plasma. It was demonstrated that zwitterionic polymer surfaces are viable alternatives to more traditional surfaces based on poly(ethylene glycol) (PEG) as nonfouling surfaces. All polymer surfaces were formed using atom transfer radical polymerization (ATRP) and they showed an increased resistance to nonspecific protein adsorption compared to SAMs. This improvement is due to an increase in the surface packing density of nonfouling groups on the surface, as well as a steric repulsion from the flexible polymer brush surfaces. The zwitterionic polymer surface based on carboxybetaine methacrylate (CBMA) also incorporates functional groups for protein immobilization in the nonfouling background, making it a strong candidate for many applications such as in diagnostics and drug delivery.     

Preparation and characterization of poly(ethylene glycol)-g-chitosan with water- and organosolubility

A new scheme was proposed for synthesizing poly(ethylene glycol)-g-chitosan (PEG-g-CS), where methoxy poly(ethylene glycol) iodide (MPEG-I) (M_n 2000) was used for N-substitution of triphenylmethyl chitosan (TPM-CS) in organic medium. The graft copolymers were obtained by subsequent removal of protecting groups with dichloroacetic acid. By varying PEG-I/TPM-CS feed ratio, the grafting levels (GL) of PEG can be adjusted. The chitosan derivatives were characterized by FTIR, ¹H NMR, ¹³C NMR and DSC. All the copolymers were soluble in water over wide pH range. Furthermore, organosolubility of the hybrids in DMF and DMSO was also achieved when the DS value more than 24%. The lysozyme degradation rate of the copolymers in aqueous neutral medium decreased with the increase of GL value.     

Range and magnitude of the steric pressure between bilayers containing phospholipids with covalently attached poly(ethylene glycol).

The interactive properties of liposomes containing phospholipids with covalently attached poly(ethylene glycol) (PEG-lipids) are of interest because such liposomes are being developed as drug delivery vehicles and also are ideal model systems for measuring the properties of surface-grafted polymers. For bilayers containing PEG-lipids with PEG molecular weights of 350, 750, 2000, and 5000, pressure-distance relations have been measured by X-ray diffraction analysis of liposomes subjected to known applied osmotic pressures. The distance between apposing bilayers decreased monotonically with increasing applied pressure for each concentration of a given PEG-lipid. Although for bilayers containing PEG-350 and PEG-750 the contribution of electrostatic repulsion to interbilayer interactions was significant, for bilayers containing PEG-2000 and PEG-5000 the major repulsive pressure between bilayers was a steric pressure due to the attached PEG. The range and magnitude of this steric pressure increased both with increasing PEG-lipid concentration and PEG size, and the extension length of the PEG from the bilayer surface at maximum PEG-lipid concentration depended strongly on the size of the PEG, being less than 35 A for PEG-750, and about 65 A for PEG-2000 and 115 A for PEG-5000. The measured pressure-distance relations have been modeled in terms of current theories (deGennes, 1987; Milner et al., 1988b) for the steric pressure produced by surface-grafted polymers, as modified by us to take into account the effects of polymer polydispersity and the possibility that, at low grafting densities, polymers from apposing bilayers surfaces can interpenetrate or interdigitate. No one theoretical scheme is sufficient to account for all the experimental results. However, for a given pressure regime, PEG-lipid size, and PEG-lipid surface density, the appropriately modified theoretical treatment gives a reasonable fit to the pressure-distance data.     

Adsorption of poly(ethylene glycol)-modified ribonuclease A to a poly(lactide-co-glycolide) surface

Protein adsorption is a source of variability in the release profiles of therapeutic proteins from biodegradable microspheres. We employ optical reflectometry and total internal reflection fluorescence to explore the extent and kinetics of ribonuclease A (RNase A) adsorption to spin-cast films of poly(lactide-co-glycolide) (PLG) and, in particular, to determine how covalent grafting of polyethylene glycol (PEG) to RNase A affects adsorption. Adsorption kinetics on PLG surfaces are surface-limited for RNase A but transport-limited for unconjugated PEG homopolymers and for PEG-modified RNase A, indicating that PEG anchors the conjugates to the surface during the transport-limited regime. PEG modification of RNase A decreases the total number of adsorbed molecules per unit area but increases the areal surface coverage because the grafted PEG chains exclude additional surface area. Total internal reflection fluorescence-based exchange measurements show that there is no exchange between adsorbed and solution-phase protein molecules. This indicates an unusually tenacious adsorption. Streaming current measurements indicate that the zeta potential of the PLG surface becomes increasingly negative as the film is exposed to water for several weeks, as expected. Aging of the PLG surface results in increased adsorption of unmodified RNase A but decreased adsorption of unconjugated PEG homopolymers and of PEG-RNase A conjugates, relative to the extent of adsorption on freshly prepared PLG surfaces. Adsorption results correlate well with an increase in the rate, total extent and preservation of bioactivity of RNase A released from PLG microspheres for the PEG-modified version of RNase A.