Glucoamylase immobilization on silochrome using gossypol

The paper is concerned with conditions of glucoamylase binding with silanized silochrome using gossypol, dialdehyde isolated from cotton-plant. Kinetic properties of the immobilized enzyme are studied. The enzyme pH optimum does not change with immobilization and the temperature optimum is shifted from 50 degrees to 60 degrees C; a certain increase of the seeming Km is also observed. A high yield of the enzyme activity in immobilization evidences for the possibility of using gossypol as a binding agent in glucoamylase immobilization.     

Immobilization of catalases from Bacillus SF on alumina for the treatment of textile bleaching effluents

A catalase preparation from a newly isolated Bacillus sp. was covalently immobilized on silanized alumina using glutaraldehyde as crosslinking agent. The effect of the coupling time of the enzyme-support reaction was determined in terms of protein recovery and immobilization yield and a certain balance point was found after which the activity recovery decreased. The activity profile of the immobilized catalase at high pH and temperature was investigated. The immobilized enzyme showed higher stabilities (214 h at pH 11, 30°C) at alkaline pH than the free enzyme (10 h at pH 11, 30°C). The immobilized catalase was inhibited by anionic stabilizers or surfactants added to the hydrogen peroxide substrate solution.     

BSA和PEG影响固定化辣根过氧化物酶HRP在有机相中活力

ＢＳＡ和ＰＥＧ可以有效地提高固定化辣根过氧化物酶（ＨＲＰ）在有机相中的活力。固定化酶活力的提高与试剂加入的顺序有密切的联系;不同载体对酶的影响不同,Ｇｅｌｉｔｅ,ａｌｕｍｉｎａ,ＸＡＤ－７,Ｋｉｓｅｌｇｅｌ和Ｆｌｏｒｉｓｉｌ为载体,分别以吸附法制备固定化酶。实验表明固定化过程中保护剂和酶的加入顺序与国家化酶活力密切相关,而这些载体的固定化效果又以Ｃｅｌｉｔｅ最佳,Ｆｌｏｒｉｓｉｌ最差。Ｆｌｏｒｉｓ     

Green coconut fiber: a novel carrier for the immobilization of commercial laccase by covalent attachment for textile dyes decolourization

Commercial laccase formulation was immobilized on modified green coconut fiber silanized with 3-glycidoxypropyltrimethoxysilane, aiming to achieve a cheap and effective biocatalyst. Two different strategies were followed: one point (pH 7.0) and multipoint (pH 10.0) covalent attachment. The influence of immobilization time on enzymatic activity and the final reduction with sodium borohydride were evaluated. The highest activities were achieved after 2?h of contact time in all situations. Commercial laccase immobilized at pH 7.0 was found to have higher activity and higher affinity to the substrate. However, the immobilization by multipoint covalent attachment improved the biocatalyst thermal stability at 50?°C, when compared to soluble enzyme and to the immobilized enzyme at pH 7.0. The Schiff's bases reduction by sodium borohydride, in spite of causing a decrease in enzyme activity, showed to contribute to the increase of operational stability through bonds stabilization. Finally, these immobilized enzymes showed high efficiency in the continuous decolourization of reactive textile dyes. In the first cycle, the decolourization is mainly due to dyes adsorption on the support. However, when working in successive cycles, the adsorption capacity of the support decreases (saturation) and the enzymatic action increases, indicating the applicability of this biocatalyst for textile wastewater treatment.     

Covalent coupling method for lipase immobilization on controlled pore silica in the presence of nonenzymatic proteins

Candida rugosa lipase was covalently immobilized on silanized controlled pore silica previously activated with glutaraldehyde in the presence of nonenzymatic proteins. This strategy is suggested to protect the enzyme from aggregation effects or denaturation that occurs as a result of the presence of silane precursors used in the formation of the silica matrix. The immobilization yield was evaluated as a function of the lipase loading and the additive type (albumin and lecithin) using statistical concepts. In agreement with the mathematical model, the maximum coupling yield (32.2%) can be achieved working at high lipase loading (450 units x g(-1) support) using albumin as an additive. In these conditions, the resulting immobilized lipase exhibits high hydrolytic (153.2 U x mg(-1)) and esterification (337.6 mmol x g(-1) x min) activities. The enhanced activity of the final lipase derivative is the sum of the benefits of the immobilization (that prevents enzyme aggregation) and the lipase coating by additives that increases the accessibility of active sites to the substrate.     

Optimized immobilization of endoglucanase Cel9A onto glutaraldehyde activated chitosan nanoparticles by response surface methodology: The study of kinetic behaviors

Immobilization of enzyme onto nanoparticles such as chitosan can have biotechnological importance. In this study, chitosan nanoparticles (ChNPs) were prepared by Ionic gelation method and Endoglucanase Cel9A from Alicyclobacillus acidocaldariius (AaCel9A) immobilized on the nanoparticles. The FTIR results showed that the enzymes were immobilized on the ChNPs. The dynamic light scattering and scanning electron microscope (SEM) results illustrated that the AaCel9A-ChNPs approximately had 40 nm diameters. For optimizing enzyme immobilization, response surface methodology was employed using different variables (pH, enzyme immobilization time, and enzyme to ChNPs ratio [E/Cs]). The results showed that the high immobilization efficiency was achieved in pH 7, E/Cs of 0.4 in 2.63 hr. The enzyme activity results showed that, immobilization increased optimum pH for activity (from 6.5 to 7.5) and the enzyme K_m (from 3.703 to 12.195 [mg/ml]), which make it suitable to use in some industries such as detergents.     

Haloalkane hydrolysis with an immobilized haloalkane dehalogenase.

Haloalkane dehalogenase from Rhodococcus rhodochrous was covalently immobilized onto a polyethyleneimine impregnated gamma-alumina support. The dehalogenating enzyme was found to retain greater than 40% of its original activity after immobilization, displaying an optimal loading (max. activity/supported protein) of 70 to 75 mg/g with an apparent maximum (max. protein/support) of 156 mg/g. The substrate, 1,2,3-trichloropropane, was found to favorably partition (adsorb) onto the inorganic alumina carrier (10 to 20 mg/g), thereby increasing the local reactant concentration with respect to the catalyst's environment, whereas the product, 2,3-dichloropropan-1-ol, demonstrated no affinity. Additionally, the inorganic alumina support exhibited no adverse effects because of solvent/component incompatibilities or deterioration due to pH variance (pH 7.0 to 10.5). As a result of the large surface area to volume ratio of the support matrix and the accessibility of the bound protein, the immobilized biocatalyst was not subject to internal mass transfer limitations. External diffusional restrictions could be eliminated with simple agitation (mixing speed: 50 rpm; flux: 4.22 cm/min). The pH-dependence of the immobilized dehalogenase was essentially the same as that for the native enzyme. Finally, both the thermostability and resistance toward inactivation by organic solvent were improved by more than an order of magnitude after immobilization.     

Immobilization of chloroperoxidase on silica-based materials for 4,6-dimethyl dibenzothiophene oxidation

Silica-based materials have been used as effective supports for the immobilization of enzymes. Moreover, the understanding on the oxidation of sulfur compounds by immobilized chloroperoxidase represents a step further in the development of a biocatalytic desulfurization process of fossil fuels. Here, chloroperoxidase from Caldariomyces fumago was immobilized on amorphous and structured silica-based materials either physically or covalently using an organosilane derivative for the oxidation of a recalcitrant organosulfur compound currently found in gas oil and diesel, such as 4,6-dimethyldibenzothiophene (4,6-DMDBT). Such materials were characterized by FTIR, N₂-adsorption, XRD, SEM and TEM. We have found that the chemical differences on the silanol/siloxane groups of SG/67 and SBA15 mesoporous materials deeply modify the enzymatic load, activity, thermal stability and reusability. The physical immobilization of CPO was characterized by a high adsorption capacity (q_m) and affinity constants (K_m) when compared to the covalent approach, but it resulted more sensitive to temperature than free, the silanized and covalently immobilized enzyme. The thermal residual activity as well as reusability of CPO were first improved by silanization, then by covalent immobilization in a support with a large pore size and high silanol/siloxane ratio.     

Cyclodextrin glucanotransferase synthesis by semicontinuous cultivation of magnetic biocatalysts from cells of Bacillus circulans ATCC 21783

Cells of the alkalotolerant producer of cyclodextrin glucanotransferase (CGTase) Bacillus circulans ATCC 21783 were used as a model for preparing of magnetic biocatalysts applied for CGTase synthesis in batch and semicontinuous processes. The cell immobilization was carried out with four types of magnetic nano- and microparticles: magnetite microparticles (1–5 μm), entrapped in agar gel beads with bacterial cells (AM-biocatalyst); silanized magnetite (20–40 nm) covalently bound on the cell surface (SM-biocatalyst); and alkaline and citrate ferrofluids (10–20 nm), attached on the cell wall by an ionic interaction (FF-alkaline and FF-citrate biocatalyst). The highest CGTase production was achieved after 96 h of semicontinuous process using SM-biocatalysts (particularly, these composed of 80 mg silanized magnetite and 140 mg bacterial cells) when the specific enzyme activity was 8.4-fold higher compared to that of free cells. Cells modified with magnetic alkaline and citrate ferrofluids exhibited 2.19- and 1.55-fold increase of the specific CGTase activities. Magnetic nanoparticles linked on the cell walls by ionic interactions were partially released during the cultivation, while the covalent bond between the activated magnetite and the cells was very stable. The data obtained demonstrate convincingly the effect of the magnetic technologies for an effective enzyme production.     

固定化青霉素V酰化酶的制备及性质

尖镰孢(Fusarium oxysporum)FP941青霉素V酰化酶经γ氧化铝吸附洗脱、硫酸铵沉淀和脱盐处理后,固定在环氧丙烯聚合物载体上,湿固定化酶表现活力为217 IU/g,固定化产率为53%。固定化酶作用最适温度为55℃,最适pH为80;在pH50～110及50℃以下稳定;37℃使用25次后,酶活力保留90%。     

Purification and immobilization of dextranase

An enzymic characteristic of Novo dextranase was presented. In addition to a high dextranolytic activity (7,200 U/ml), the crude enzyme also contained small amounts of protease, glucoamylase, polygalacturonase, carboxymethylcellulase, laminarinase and chitinase. A highly purified dextranase was then simply separated from a commercial preparation by column chromatographies on DEAE-Sepharose, CM-Sepharose, and by chromatofocussing on Polybuffer Exchanger PBE-94. The enzyme was recovered with an over 200-fold increase in specific activity and a yield of 84%. The final preparation was homogeneous, as observed during high performance liquid chromatography (HPLC). Size-exclusion HPLC indicated that dextranase had a molecular mass of 35 kDa and its isoelectric point, established by chromatofocussing, was 4.85. Analysis of the dextran break-down products indicated that purified dextranase represents an endolytic mode of action, and isomaltose and isomaltotriose were identified as the main reducing sugars of dextran hydrolysis. The enzyme was then covalently coupled to the silanized porous glass beads modified by glutaraldehyde (Carrier I) or carbodiimide (Carrier II). It was shown that immobilization of dextranase gave optimum pH and temperature ranges from 5.4 to 5.7 and from 50°C to 60°C, respectively. The affinity of the enzyme to the substrate decreased by a factor of more than 13 for dextranase immobilized on Carrier I and increased slightly (about 1.4-times) for the enzyme bound to Carrier II.     

Characterization of immobilized enzymes in polyurethane foams in a dynamic bed reactor

-d-Galactosidase (E 3.2.1.23) from Aspergillus oryzae was immobilized with polyurethane foam (PUF). Among several immobilization methods attempted in this work, the immobilized enzyme preparation by in-situ co-polymerization between enzyme and prepolymer HYPOL 3000 showed the highest activity. The intrinsic kinetics of PUF-immobilized enzyme was determined in a dynamic bed reactor, used to increase transport rates. The immobilization mechanism in PUF was studied by measurements of immobilized enzyme kinetics and by using scanning electron microscopy combined with immuno-gold labeling techniques. The results showed that immobilization was predominantly by covalent bonding between primary amino groups of -d-galactosidase and isocyanate groups of the prepolymers. Entrapment in the PUF micropores assisted the immobilization of enzymes, and adsorption on the surface of macropores was not important for immobilization. The bicinchoninic acid method was applied for the determination of PUF loading capacity and specific enzyme activity and used to determine enzyme deactivation during immobilization.     

Silanized nucleic acids: a general platform for DNA immobilization

We have developed a method for simultaneous deposition and covalent cross-linking of oligonucleotide or PCR products on unmodified glass surfaces. By covalently conjugating an active silyl moiety onto oligonucleotides or cDNA in solutions we have generated a new class of modified nucleic acids, namely silanized nucleic acids. Such silanized molecules can be immobilized instantly onto glass surfaces after manual or automated deposition. This method provides a simple and rapid, yet very efficient, solution to the immobilization of prefabricated oligonucleotides and DNA for chip production.     

Method for stretching DNA molecules on mica surface in one direction for AFM imaging.

An efficient method was developed to stretch DNA molecules on an atomically flat surface for AFM imaging. This method involves anchoring DNA molecules from their 5' ends to amino silanized mica surfaces. N-Succinimidyl6-[3'-(2-pyridyldithio) propionamido]hexanoate (LC-SPDP), a heterobifunctional cross-linker with a flexible spacer arm was used for this purpose. The immobilization process was carried out by introducing a thiol group to the 5' end of DNA by PCR. Thiolated molecules were then reacted with the cross linker to conjugate with its 2-pyridyl disulphide group via sulfhydryl exchange. The resulting complex was deposited on amino silanized mica where NHS-ester moiety of the cross linker reacted with the primary amino group on the surface. Samples were washed by a current of water and dried by an air jet in one direction parallel to the surface. DNA molecules were shown to be fully stretched in one direction on imaging them by AFM.     

Immobilization of cellulolytic and hemicellulolytic enzymes on inorganic supports

Commercial cellulase preparations from Trichoderma viride and Aspergillus niger were immobilized on porous silica glass and ceramics such as alumina and titania with titanium tetrachloride (TiCl(4)) and on their silanized derivatives with glutaraldehyde (GLUT). The amounts of the immobilized enzymes were in the range 10-50 mg/g carrier (dry) depending on the kind of carrier and immobilization method. Their activities toward carboxymethyl cellulose (CMC), xylan, aryl-beta-glucoside, and aryl-beta-xyloside were 3-53% of those of the native enzymes. The optimum pH of the enzymes shifted to the acidic side in most cases, whereas the optimum temperatures were nearly the same as those of native ones. The activity of immobilized enzyme preparations towards CMC did not change significantly during continuous operation over a periods of 60 days. Finally, xylan was hydrolyzed with the immobilized enzymes, and the sugars formed were investigated.     

Papain Immobilization Study in Enzymatic Synthesis of Dipeptide Gly-Phe

Papain catalysed peptide synthesis was followed to determine the optimum conditions for adsorption and covalent binding immobilization methods. The synthesis of the dipeptide Gly-Phe was studied in two different reaction systems: a) For adsorbed papain, in an organic medium containing low water concentration, b) For covalently bound enzyme, in a two-liquid phase system, using trichloroethylene as organic phase. The amount of enzyme offered to the immobilization support and the p^H of the immobilization procedure were the main parameters studied.     

壳聚糖固定化琼脂酶的研究

采用壳聚糖微球对琼脂酶进行固定化,在单因素实验的基础上用正交试验法确定最佳固定化工艺。结果表明:在戊二醛体积分数为2.5%,交联时间为6 h,加酶量为15 mL,固定时间为3 h时固定酶的活力最高;固定化酶的最适反应温度及最适pH分别为50℃和8.5,高于游离酶;同时其热稳定性及操作稳定性均高于游离酶。     

Improvement of the stability and selectivity of Rhizomucor miehei lipase immobilized on silica nanoparticles: Selective hydrolysis of fish oil using immobilized preparations

We report the effect of random and oriented immobilization of Rhizomucor miehei lipase (RML) on its functional properties. For this purpose, silica nanoparticles (MCM-41 and SBA-15) were prepared, characterized and functionalized by glycidyloxypropyl trimethoxysilane. Direct immobilization of RML on these supports was performed via the variety of amino acid residues on the surface of RML which promotes random immobilization. To perform oriented immobilization, partial modification of epoxy functionalized supports was carried out by introducing iminodiacetic acid groups followed by addition of Cu²⁺. In this way, immobilization is mainly directed via the most accessible histidine group, followed by intramolecular reaction of the other nucleophilic residues of the enzyme and the remaining epoxy groups on the support. The results showed higher thermal stability for immobilized derivatives compared to the soluble enzyme. Co-solvent stability of the derivatives was also studied in presence of six polar organic solvents (DMSO, THF, acetonitrile, 1-propanol, 2-propanol and dioxane). Influence of the immobilization procedure on activity and selectivity of the immobilized preparations was studied in selective hydrolysis of fish oil. All the derivatives discriminate between cis-5,8,11,14,17-eicosapentaenoic acid (EPA) and cis-4,7,10,13,16,19-docosahexaenoic acid (DHA) in favor of EPA. Remarkable improvement in selectivity was obtained using oriented immobilization of RML.     

Immobilization conditions of ketoreductase on enantioselective reduction in a gas-solid bioreactor

The immobilization conditions of commercial ketoreductase for continuous enantioselective reduction in the gas-phase reaction were investigated with respect to the immobilization efficiency (residual activity and protein loading) and the gas-phase reaction efficiency (initial reaction rate, half-life, and enantioselectivity). For the analyses, ketoreductase was first immobilized by physical deposition on glass supports and the reduction of 2-butanone to (S)-2-butanol with the concomitant regeneration of NADH by 2-propanol was used as a model reaction. The optimal conditions of enzyme immobilization were obtained using an absolute pressure of 100 hPa for drying, a pH between 6.5 and 7.0, and a buffer concentration of 50 mM. The buffer concentration in particular had a strong effect on both the enzyme activity and enantioselectivity. Under optimal immobilization conditions, the thermostability of ketoreductase in the gas-phase system was enhanced compared to the aqueous-phase system, while the enantioselectivity was successfully maintained at a level identical to that of the native enzyme. These results indicate that the gas-phase reaction has a great potential for industrial production of chiral compounds, but requires careful optimization of immobilization conditions for the reaction to progress effectively.     

磁性纳米颗粒固定化乙醇脱氢酶的研究

本研究采用3-丙氨基三乙氧基硅烷(APTES)和戊二醛修饰包裹有SiO2磁性Fe3O4纳米颗粒表面,将其作为固定化载体固定化乙醇脱氢酶,研究固定化条件对固定化效率的影响,并对固定化酶性质进行分析。研究发现,当Fe3O4@SiO2纳米颗粒修饰上氨基和醛基后依然具有良好的水分散性和胶体稳定性,适合作为固定化载体。通过单因素优化,发现当最适给酶量为11. 3U/100 mg,搅拌转速为150 r/min,固定化p H和固定化温度分别控制在6. 5和5℃～15℃,固定化时长为45 min时,具有较好的固定化效果,固定化率可达到60. 2%。在此条件下制备得到的固定化酶与游离酶相比,固定化酶具有良好的耐高温和耐碱性。所得固定化乙醇脱氢酶在连续使用8次后,固定化率仍保留在57%左右,表明该固定化酶具有较好的操作稳定性,可为连续生产NADH提供技术依据。