Outdoor and indoor cultivation of Spirulina platensis in the extreme south of Brazil

Water supplemented with 10% or 20% (v/v) of Zarrouk medium was used to cultivate Spirulina platensis in closed and open bioreactors under controlled conditions (30 degrees C, 32.5 micromol m(-2) s(-1), 12 h light/dark photoperiod) and in a greenhouse (9.4 to 46 degrees C, up to 2800 micromol m(-2) s(-1), variable day length photoperiod) using different initial biomass concentrations (X0) in the extreme south of Brazil (32.05 degrees S, 52.11 degrees W). Under controlled conditions the maximum specific growth rate (micromax) was 0.102 d(-1), the biomass doubling time (t(d)) was 6.8 d, the maximum dry biomass concentration (Xmax) was 1.94 g L(-1) and the maximum productivity (Pmax) was 0.059 g L(-)1 d(-1), while the corresponding values in the greenhouse experiments were micromax = 0.322 d(-1), t(d) = 2.2 d, Xmax = 1.73 g L(-1) and Pmax = 0.112 g L(-1) d(-1). Under controlled conditions the highest values for these parameters occurred when X0 = 0.15 g L(-1), while in the greenhouse X0 = 0.4 g L(-1) produced the highest values. These results show that the cultivation of S. platensis in greenhouses in the extreme south of Brazil is technically viable and that the S. platensis inoculum and the concentration of Zarrouk medium can be combined in such a way as to obtain growth and productivity parameters comparable, or superior, to those occurring in bioreactors under controlled conditions of temperature, illuminance and photoperiod.     

Impact of ammonia concentration on Spirulina platensis growth in an airlift photobioreactor

Spirulina platensis was cultivated in a bench-scale airlift photobioreactor using synthetic wastewater (total nitrogen 412 mg L(-1), total phosphorous 90 mg L(-1), pH 9-10) with varying ammonia/total nitrogen ratios (50-100% ammonia with balance nitrate) and hydraulic residence times (15-25 d). High average biomass density (3500-3800 mg L(-1)) and productivity (5.1 g m(-2) d(-1)) were achieved when ammonia was maintained at 50% of the total nitrogen. Both high ammonia concentrations and mutual self-shading, which resulted from the high biomass density in the airlift reactor, were found to partially inhibit the growth of S. platensis. The performance of the airlift bioreactor used in this study compared favorably with other published studies. The system has good potential for treatment of high strength wastewater combined with production of algae for biofuels or other products, such as human and animal food, food supplements or pharmaceuticals.     

Simultaneous cultivation of Spirulina platensis and the toxigenic cyanobacteria Microcystis aeruginosa

Mangueira Lagoon, located in the extreme south of Brazil, has water with physicochemical characteristics such as alkaline pH and carbonate levels propitious for the growth of the cyanobacterium Spirulina platensis. Previously published studies have shown that Mangueira Lagoon water supplemented with small quantities of carbon and nitrogen is suitable for S. platensis cultivation and can significantly reduce production costs. We studied mixed cultures of Spirulina platensis and the toxic cyanobacterium Microcystis aeruginosa using a 2(3) factorial design in which the three factors were the initial biomass concentration of S. platensis and M. aeruginosa and the type of culture medium (100% Zarrouk's medium or 80% Mangueira Lagoon water plus 20% Zarrouk's medium). The highest S. platensis maximum specific growth rate (mu(max)) occurred in the culture with the highest M. aeruginosa biomass concentration and when undiluted culture medium was used (micro(max) = 0.283 d(-1)). The highest M. aeruginosa specific death rate (k) was obtained in the presence of S. platensis (k = 0.555 d(-1)) and was independent of the initial M. aeruginosa biomass concentration and culture medium, demonstrating that S. platensis cultures are not susceptible to contamination by M. aeruginosa. The culture medium had no significant influence (p > 0.05) on S. platensis micro(max) values, indicating that production costs could be reduced by using a medium consisting of 80% Mangueira Lagoon water plus 20% Zarrouk's medium.     

Spirulina platensis growth in open raceway ponds using fresh water supplemented with carbon,nitrogen and metal ions

To investigate the feasibility of using fresh water from Mangueira Lagoon (Rio Grande do Sul, Brazil) for biomass production in open raceway ponds (0.7 m long, 0.18 m wide, 0.075 m deep) we studied the influence of nutrient addition (carbon as sodium bicarbonate, nitrogen as urea, phosphate, sulfate, ferric iron, magnesium and potassium) on the growth rate of the cyanobacteria Spirulina platensis using a 22 factorial design. In unsupplemented lagoon water production of S platensis was 0.78 +/- 0.01 g/l (dry weight basis) while the addition of 2.88 g/l of sodium bicarbonate (without added urea, phosphate, sulfate or metal ions) resulted in 0.82 +/- 0.01 g/l after 400 hours of culture. The further addition of phosphate and metal ions resulted in growth for up to 750 h and a final S. platensis biomass of 1.23 +/- 0.04 to 1.34 +/- 0.03 g/l.     

Photosynthetic performance of a helical tubular photobioreactor incorporating the cyanobacterium spirulina platensis

The photosynthetic performance of a helical tubular photobioreactor ("Biocoil"), incorporating the filamentous cyanobacterium Spirulina platensis, was investigated. The photobioreactor was constructed in a cylindrical shape (0.9 m high) with a 0.25-m(2)basal area and a photostage comprising 60 m of transparent PVC tubing of 1.6-cm inner diameter (volume = 12.1 L). The inner surface of the cylinder (area = 1.32 m(2)) was illuminated with cool white fluorescent lamps; the energy input of photosynthetically active radiation(PAR, 400 to 700 nm) into the photobioreactor was 2920 kJ per day. An air-lift system ncorporating 4%CO(2) was used to circulate the growth medium in the tubing. The maximum productivity achieved in batch culture was 7.18 g dry biomass per day [0.51 g . d biomass/L . day, or 5.44 g . d biomass/m(2)(inner surface of cylindrical shape)/day] which corresponded to a photosynthetic (PAR) efficiency of 5.45%. The CO(2) was efficiently removed from the gaseous stream; monitoring the CO(2) the outlet and inlet gas streams showed a 70% removal of CO(2) from the inlet gas over an 8-h period with almost maximum growth rate. (c) 1995 John Wiley & Sons, Inc.     

Improving Spirulina platensis biomass yield using a fed-batch process

Increasing interest is being shown in the cyanobacterium Spirulina platensis because of its nutritional properties when used as food supplement and possible therapeutic effects. One of the most important areas being studied is the development of alternative nutrient sources which can be used to decrease the production costs of commercially produced S. platensis and obtain high productivity. Water from Mangueira Lagoon (Rio Grande do Sul State, Brazil) has high levels of carbonates and a high pH and has the potential to be used as a culture medium for S. platensis, although some nutrient supplementation may be required. We tested the effect of unsupplemented Mangueira Lagoon water (MLW) or MLW supplemented with 1.125 or 2.250 mg/l of urea and/or 21 or 42 mg/l of sodium bicarbonate on the growth of S. platensis in fed-batch culture using a 3(2) factorial design and found that there the addition of 1.125 mg/l of urea resulted in a 2.67 fold increase times in the final biomass concentration of S. platensis.     

Chlorophyll production from Spirulina platensis: cultivation with urea addition by fed-batch process

The cyanobacterium Spirulina platensis is an attractive alternative source of the pigment chlorophyll, which is used as a natural color in food, cosmetic, and pharmaceutical products. In this work, the influence of the light intensity and urea supplementation as a nitrogen source using fed-batch cultivation for S. platensis growth and chlorophyll content was examined. Cultivations were carried out in 5 l open tanks, at 30+/-1 degrees C. Response surface methodology was utilized for analysis of the results, and models were obtained for biomass productivity, nitrogen-cell conversion factor and chlorophyll productivity. The best cellular growth was observed with 500 mg/l of urea at a light intensity of 5600 lx, whereas the highest concentration of chlorophyll in the biomass was observed with 500 mg/l of urea at a light intensity of 1400 lx. Overall, the best chlorophyll productivity was observed with 500 mg/l of urea at a light intensity of 3500 lx, providing the optimal balance between the cellular growth and the biomass chlorophyll content.     

Factors indicating culture status during cultivation of Spirulina (Arthrospira) platensis

Factors indicating culture status of two Spirulina platensis strains were monitored in a batch mode cultivation for 36 days. Changing mode in all factors showed a common turning point, indicating shift of cell or culture status. Mean biomass productivity was highly sustained until day 22, chlorophyll a concentration peaked on day 22, pH value was >12 on day 22, coil number was abruptly shortened on day 22, and floating activity was sustained at greater than 79% after day 22, indicating that day 22 is a criterion reflecting phase-transfer in cell physiology in a batch culture system. Many of these changes may have been caused by increased pH, suggesting that pH control is essential for mass production of S. platensis. Fluctuations in floating activity were likely induced by the number of cellular gas vacuoles. Consequently, coil number per trichome and floating activity of S. platensis could readily act as simple indicators for determination of culture status or harvesting time of cells.     

pH对小球藻Chlorella sp. XQ-200419光合作用、生长和产油的影响

以一种生长快、油脂含量高的小球藻(Chlorella sp. XQ-200419)为实验材料, 利用测定净光合放氧速率的方法研究了pH对其光合作用的影响; 使用改良的BG-11培养基在微藻环形培养池模拟系统中进行分批培养, 培养周期为8d, 培养过程中使用 pH控制仪在线监测藻液的pH, 根据pH变化, 自动接通、关闭CO2通气管道, 将藻液pH分别控制在5.06.0, 7.08.0, 8.09.0, 9.010.0, 10.011.0内, 研究pH对生长速率、生物质面积产率、总脂含量和总脂面积产率的影响。主要结果如下: 藻液pH对小球藻Chlorella sp. XQ-200419光合放氧、生长速率、生物质产率、总脂含量和产率都有显著影响, 适宜的pH范围是7.09.0, 在此范围内, 光合放氧、生长速率、生物质产率、总脂含量和产率均保持较高水平, 且pH的影响不显著; pH低于7.0, 高于9.0, 其光合放氧、生长速率、生物质产率、总脂含量和产率都显著降低。这表明pH对小球藻Chlorella sp. XQ-200419光合作用的影响和对生长、产油的影响是一致的。pH 7.08.0, 小球藻的生物质平均面积产率和总脂平均面积产率都达到最大值, 分别是8.9 g/(m2d)和2269.5 mg/(m2d); 当藻液pH超过10.0, 生物质平均面积产率和总脂平均面积产率分别降低42.1%和60.0%。适合于小球藻生长的pH也有利于其积累油脂, 所以, pH对小球藻产油的影响是一种适宜模式, 而非胁迫模式。规模化培养小球藻Chlorella sp. XQ-200419, 通过补充CO2将藻液pH控制在7.09.0内, 可以获得高生物质产率和总脂产率。研究结果反映出pH对小球藻光合作用、生长和产油影响的规律, 也为规模化培养小球藻生产微藻油脂过程中合理控制藻液pH提供了依据。       

Co2+, Cu2+, and Zn2+ accumulation by cyanobacterium Spirulina platensis

The Spirulina platensis biomass was characterized for its metal accumulation as a function of pH, external metal concentration, equilibrium isotherms, kinetics, effect of co-ions under free (living cells, lyophilized, and oven-dried) and immobilized (Ca-alginate and polyacrylamide gel) conditions. The maximum metal biosorption by S. platensis biomass was observed at pH 6.0 with free and immobilized biomass. The studies on equilibrium isotherm experiments showed highest maximum metal loading by living cells (181.0 +/- 13.1 mg Co(2+)/g, 272.1 +/- 29.4 mg Cu(2+)/g and 250.3 +/- 26.4 mg Zn(2+)/g) followed by lyophilized (79.7 +/- 9.6 mg Co(2+)/g, 250.0 +/- 22.4 mg Cu(2+)/g and 111.2 +/- 9.8 mg Zn(2+)/g) and oven-dried (25.9 +/- 1.9 mg Co(2+)/g, 160.0 +/- 14.2 mg Cu(2+)/g and 35.1 +/- 2.7 mg Zn(2+)/g) biomass of S. platensis on a dry weight basis. The polyacrylamide gel (PAG) immobilization of lyophilized biomass found to be superior over Ca-alginate (Ca-Alg) and did not interfere with the S. platensis biomass biosorption capacity, yielding 25% of metal loading after PAG entrapment. The time-dependent metal biosorption in both the free and immobilized form revealed existence of two phases involving an initial rapid phase (which lasted for 1-2 min) contributing 63-77% of total biosorption, followed by a slower phase that continued for 2 h. The metal elution studies conducted using various reagents showed more than 90% elution with mineral acids, calcium salts, and Na(2)EDTA with free (lyophilized or oven-dried) as well as immobilized biomass. The experiments conducted to examine the suitability of PAG-immobilized S. platensis biomass over multiple cycles of Co(2+), Cu(2+), and Zn(2+) sorption and elution showed that the same PAG cubes can be reused for at least seven cycles with high efficiency.     

An optical-density-based feedback feeding method for ammonium concentration control in Spirulina platensis cultivation

Cultivation of Spirulina platensis using ammonium salts or wastewater containing ammonium as alternative nitrogen sources is considered as a commercial way to reduce the production cost. In this research, by analyzing the relationship between biomass production and ammonium- N consumption in the fed-batch culture of Spirulina platensis using ammonium bicarbonate as a nitrogen nutrient source, an online adaptive control strategy based on optical density (OD) measurements for controlling ammonium feeding was presented. The ammonium concentration was successfully controlled between the cell growth inhibitory and limiting concentrations using this OD-based feedback feeding method. As a result, the maximum biomass concentration (2.98 g/l), productivity (0.237 g/l·d), nitrogen-to-cell conversion factor (7.32 gX/gN), and contents of protein (64.1%) and chlorophyll (13.4 mg/g) obtained by using the OD-based feedback feeding method were higher than those using the constant and variable feeding methods. The OD-based feedback feeding method could be recognized as an applicable way to control ammonium feeding and a benefit for Spirulina platensis cultivations.     

Kinetic and growth parameters of Arthrospira (Spirulina) platensis cultivated in tubular photobioreactor under different cell circulation systems

Arthrospira platensis was cultivated in tubular photobioreactor in order to evaluate growth and biomass production at variable photosynthetic photon flux density (PPFD = 60, 120, and 240 μmol photons m(-2)s(-1)) and employing three different systems for cell circulation, specifically an airlift, a motor-driven pumping and a pressurized system. The influence of these two independents variables on the maximum cell concentration (X(m)), cell productivity (P(x)), nitrogen-to-cell conversion factor (Y(X/N) ), photosynthetic efficiency (PE), and biomass composition (total lipids and proteins), taken as responses, was evaluated by analysis of variance. The statistical analysis revealed that the best combination of responses' mean values (X(m) = 4,055 mg L(-1), P(x) = 406 mg L(-1)day(-1), Y(X/N) = 5.07 mg mg(-1), total lipids = 8.94%, total proteins = 30.3%, PE = 2.04%) was obtained at PPFD = 120 μmol photons m(-2)s(-1); therefore, this light intensity should be considered as the most well-suited for A. platensis cultivation in this photobioreactor configuration. The airlift system did not exert any significant positive statistical influence on the responses, which suggests that this traditional cell circulation system could successfully be substituted by the others tested in this work.     

Improvement of Panax notoginseng cell culture for production of ginseng saponin and polysaccharide by high density cultivation in pneumatically agitated bioreactors

A Panax notoginseng cell culture was successfully scaled up from shake flask to 1.0-L bubble column reactor and concentric-tube airlift reactor. High-density bioreactor batch cultivation was carried out using a modified MS medium. The maximum cell density in batch cultures reached 20.1, 21.0 and 24.1 g/L in the shake flask, bubble column and airlift reactors, respectively, and their corresponding biomass productivity was 950, 1140 and 1350 mg/(L x d) for each. The productivity of ginseng saponin was 70, 96 and 99 mg/(L x d) in the flask, bubble column and airlift reactors, respectively; and the polysaccharide productivity reached 104, 119 and 151 mg/(L x d) for each. Furthermore, a fed-batch cultivation strategy was developed on the basis of specific oxygen uptake rate (SOUR), i.e., sucrose feeding before a sharp decrease of SOUR, and the highest cell density of 29.7 g/L was successfully achieved in the airlift bioreactor on day 17 with a very high biomass productivity of 1520 mg/(L x d). The concentrations of ginseng saponin and polysaccharide reached about 2.1 and 3.0 g/L, respectively, and their productivity was 106 (saponin) and 158 mg/(L x d) (polysaccharide). This work successfully demonstrated the high-density bioreactor cultivation of P. notoginseng cells in pneumatically agitated bioreactors and the reproduction of the shake flask culture results in bioreactors. The cell density, biomass productivity, production titer and productivity of both ginseng saponin and polysaccharide obtained here were the highest that have been reported on a reactor scale for all the ginseng species.     

Production of eicosapentaenoic acid by Nannochloropsis sp. cultures in outdoor tubular photobioreactors

Autotrophic microalgae cultures have been proposed as an alternative source of EPA, a nutritionally important polyunsaturated fatty acid that plays a key role in the prevention and treatment of several human diseases and disorders. The technology currently available is however, considered commercially not viable because of the low degree of control of algae cultures in outdoor open ponds. The use of closed reactors could overcome these limitations and bring EPA production by microalgae closer to becoming a reality. In this study, we have demonstrated the feasibility of outdoor cultivation of Nannochloropsis sp. in tubular reactors and the potential of this eustigmatophyte as an alternative source of EPA. Nannochloropsis sp. was cultivated in NHTRs of different sizes (from 10.2 to 610 l) from spring to autumn under the climatic conditions of central Italy. EPA productivity essentially reflected the productivity of the culture and reached its maximum in May–June (mean monthly value: 32 mg l⁻¹ day⁻¹). Although the fatty acid composition of the biomass varied significantly during the cultivation period, EPA content remained rather stable around the value of 4% of dry biomass. The transfer of the cultures from laboratory to outdoor conditions, the exposure to natural light–dark cycles, along with lowering the salt concentration from 33 g l⁻¹ (seawater salinity value) to 20 g l⁻¹, factors that caused lasting modifications in the fatty acid content and composition of Nannochloropsis sp., did not significantly affect the EPA content of the biomass.     

Investigation of continuous-batch mode of two-stage culture of Nannochloropsis sp. for lipid production

Microalgal lipid induction through nitrogen stress often suffers from a contradiction between biomass productivity and lipid content, i.e., either high biomass productivity with low lipid content or vice versa. A two-stage nitrogen-replete and nitrogen-deplete (NR–ND) culture was suggested to be an option to attain high lipid productivity. In this study, the effects of culture conditions and modes on biomass productivity and lipid productivity of Nannochloropsis sp. in the two stages were comprehensively investigated. The optimal culture conditions for the two stages, aiming to high biomass productivity and lipid productivity respectively, were consistent, i.e., CO₂ content in aeration (1 %), phosphorus concentration in medium (181 μmol/L), incident light intensity (150 μE/(m²s)), temperature (25 °C). Different culture modes of the two stages were compared. The overall lipid productivity of the two-stage continuous-batch mode achieved 0.123 g/(L day), which was 60.3, 48.2, 34.9 and 13.5 % higher than that of single nitrogen-replete batch, single nitrogen-limited batch, continuous nitrogen-replete culture and two-stage batch–batch culture, respectively, and also higher than most reported values. This contribution provides fundamental data for the two-stage NR–ND cultivation process design of Nannochloropsis sp.     

天祝高寒珠芽蓼草甸初级生产力的研究I.生物量动态及光能转化率

甘肃天祝高寒珠芽蓼草甸5月20日左右返青。地上生物量的变化呈单峰曲线,最大值在8月22日,干物质为548.39g／m2(489.06g／m2去灰分物质;下同);净第一性生产力为481.05g／m2·a干物质。地下生物量很大,6一9月平均接近6kg／m2,呈单谷曲线变化,最低值出现在7月20日,为4556.87g／m2干物质。地上部分最大生长率出现在月平均气温只有8—10℃的返青后一个月,平均绝对生长率为5.89g／m2·d干物质,平均相对生长率为0.152g／g·d干物质。春季地上部分的最大生长率与活根的很大消耗联系在一起。地上部分对太阳总辐射的转化率为0.155%,对生理辐射的转化率为0.316%,对≥0℃-≤0℃生长期的生理辐射的转化率为0.692%。地上部分在生长的第一个月对总辐射的表观转化率最高,平均为0.57%。     

Effects of electromagnetic field on the batch cultivation and nutritional composition of Spirulina platensis in an air-lift photobioreactor

Spirulina platensis was batch cultivated in a novel 3.5l magnetic air-lift photobioreactor with external-loop on which 0-0.55 T electromagnetic field (EMF) was imposed to investigate the EMF effects on the algal growth and nutrition composition. At the same time, the correlative mechanism was discussed mainly based on C, N, P uptake. It was found that, EMF has double-side effects on S. platensis cultivation depend on EMF intensity. 0.25 T EMF stress was found to be suitable for the algal cultivation enhancement increasing the maximum cell dry weight by 22% in a time period two days less than that of the control at 35 degrees C and 252 micromol photonsm(-2)S(-1). In addition, the nutritional composition of S. platensis was improved in both essential amino acids such as histidine and trace elements Ni, Sr, Cu, Mg, Fe, Mn, Ca, Co and V. It was suggested it was possible to optimize the cultivation process of S. platensis by imposing suitable weak EMF which may enhance the nutrition assimilation e.g. C, N, P and minerals by S. platensis.     

Production of biomass and nutraceutical compounds by Spirulina platensis under different temperature and nitrogen regimes

The cyanobacterium Spirulina platensis has been used by humans because of its nutritional and possibly medicinal effects. Our study evaluated the influence of temperature and nitrogen concentration in the medium on the production of biomass by this cyanobacterium and the biomass composition in protein, lipid and phenolic compounds. We found that at 35 degrees C there was a negative effect on biomass production but a positive effect on the production of protein, lipids and phenolics, the highest levels of these compounds being obtained in Zarrouk's medium containing 1.875 or 2.500 g l(-1) sodium nitrate. Higher biomass densities and productivity were obtained at 30 degrees C than at 35 degrees C, but nitrogen concentration appeared to have no effect on the amount of protein, lipid or phenolics, indicating that at 30 degrees C the concentration of sodium nitrate in Zarrouk's medium (2.50 g l(-1)) can be reduced without loss of productivity, an important cost-saving factor in large-scale cultivation.     

Seagrass monitoring at Perezoso, Cahuita, Costa Rica (CARICOMP site)

The seagrass of Perezoso (Cahuita National Park, Caribbean coast of Costa Rica) was monitored using the CARICOMP protocol. Productivity (2.7 +/- 1.15 g/m2/d; n=74) was intermediate, compared to other Caribbean sites. Total biomass was intermediate to high (750-1500 g/m2) at most CARICOMP sites (Colombia, Cuba, Mexico, Puerto Rico and Venezuela) including Costa Rica (822.8 +/- 391.84 g/m2; n=32). Turnover rates were high (5.5 +/- 1.36%; n=74) compared to what was found in March and August at other sites. Shoot densities average 725 shoots/m2, in the Caribbean region, while in Costa Rica the value was higher (1184 +/- 335.5 shoots/m2). Average leaf length and width in the entire region were 14.4 cm and 10.6 mm, respectively, similar to what we found, but leaf area index average 3.4 m2 m(-2), higher than what was found in Costa Rica (0.92 m2 m(-2)). At Cahuita, seagrass productivity was significantly lower in March 2005 compared with the previous six years, and biomass has decreased with time. Seagrass productivity and biomass are being affected by the maximum temperatures, which increased by almost 10 degrees C from 1999 to 2005, and show a high negative correlation. Turnover rate and temperature were not correlated. Recreational boating, swimming and nutrient loading from deforested lands in the coast, the upstream rivers and local pollution are potential sources of impact to the seagrass beds at Cahuita.     

Temporal variation of biomass and productivity of Thalassia testudinum (Hydrocharitaceae) in Venezuela, Southern Caribbean

Annual biomass and productivity of Thalassia testudinum were determined during a year at a seagrass bed located in the Parque Nacional Morrocoy, Venezuela. Leaf, rhizome and root biomass were determined monthly, together with short-shoot density, from February 1992 to January 1993, from nine replicated core samples. Productivity was measured using the methodology by Zieman (1974) with minor modifications, and leaf turnover rate was calculated. Leaf biomass values ranged between 101.73 dry g m(-2) in February and 178.11 dry g m(-2) in August. Productivity ranged from 1.69 dry g m(-2) d(-1) in April and October to 3.30 dry g m(-2) d(-1) in July, showing two annual peaks: one in July and one in March. The leaf turnover rate showed the highest value in June (2.41% d(-1)) and the lowest in May (1.23% d(-1)). Sampling time differences in leaf biomass, productivity and turnover rate were statistically significant. Short-shoot density values varied between 811.10 shoots m(-2) in April and 1226.08 shoots m(-2) in December, but the differences were not significant along the year. These results indicated seasonal trends for leaf biomass, productivity and turnover rate of T. testudinum in the Southern Caribbean (latitude 10 degrees N).