Determination of digoxin in serum samples using a flow-through fluorosensor based on a molecularly imprinted polymer

This work describes the development of a competitive flow-through FIA assay for digoxin using a molecularly imprinted polymer (MIP) as the recognition phase. In previous work, a number of non-covalent imprinted polymers were synthesised by “bulk” polymerisation. The digoxin binding and elution characteristics of these MIPs were then evaluated to obtain a highly selective material for integration into a sensor. The optimum MIP was synthesised by photo-initiated polymerisation of a mixture containing digoxin, MAA, EDGMA and AIBN in acetonitrile. The bulk polymer was ground and sieved and the template removed by Soxhlet extraction in MeOH/ACN. The MIP was packed into a flow cell and placed in a spectrofluorimeter to integrate the reaction and detection systems. The physical and chemical variables involved in digoxin determination by the sensor (nature and concentration of solution, flow rates, etc.) were optimised. Binding with the non-imprinted polymer (NIP) was also analysed. The new fluorosensor showed high selectivity and sensitivity, a detection limit of 1.7 × 10⁻² μg l⁻¹, and high reproducibility (R.S.D. of 1.03% and 1.77% for concentrations of 1.0 × 10⁻³ and 4.0 × 10⁻³ mg l⁻¹, respectively). Selectivity was tested by determining the cross-reactivity of several compounds with structures analogous to digoxin. Under the assay conditions used, in which the potential interfering compounds were in concentrations 100 times higher than that of the analyte, no interference was recorded. The proposed fluorosensor was successfully used to determine digoxin concentration of human serum samples.     

Optimizing the formulation of a myoglobin molecularly imprinted thin-film polymer--formed using a micro-contact imprinting method

Thin-film myoglobin molecularly imprinted polymers have been fabricated using a micro-contact approach. By initially selecting the cross-linker on the basis of it having a minimal recognition for the template and using this as a starting point for functional monomer selection, we have produced myoglobin imprinted polymers with exceptionally high selectivities.

The affinity of the polymers, for myoglobin, when prepared with a variety of different cross-linkers and no functional monomer was evaluated. Of these, tetraethylene glycol dimethacrylate (TEGDMA) exhibited the lowest affinity for the template species. Methyl methacrylate (MMA) was chosen as the functional monomer as when it was used in conjunction with TEGDMA, it exhibited maximum selectivity for the template compared to polymers made with other functional monomers.

With a MMA to TEGDMA ratio of 1 to 3, the myoglobin molecularly imprinted polymer adsorbed 15.03 ± 0.89 × 10⁻¹¹ mole/cm² of template from a 5.68 × 10⁻⁷ M myoglobin solution, compared to 2.58 ± 0.02 × 10⁻¹¹ mole/cm² for a polymer of similar composition, but formed in the absence of a template. Various washing conditions, using alkaline media to remove the template, were investigated. An extraction solvent comprising 2 wt.% SDS and 0.6 wt.% NaOH used at 80 °C for 30 min was shown to give the highest imprinting factor i.e. 5.83 with 72.82% myoglobin removal.

The saturation kinetics of template binding to the thin-film MIP were examined and found to display a simple two-phase profile typical of non-cooperative binding. A Scatchard binding plot showed the dissociation constant (K_d) for the specific binding phase to be 3.4 × 10⁻⁷ M and the binding site capacity to be 7.24 × 10⁻¹¹ mole/cm². For the non-specific binding phase, K_d was found to be 1.355 × 10⁻⁵ M and the binding site capacity was determined as 9.62 × 10⁻¹⁰ mole/cm².

Selectivity experiments were carried out in both single protein and binary protein systems all using a total protein concentration of 5.68 × 10⁻⁷ M. The molar ratio of adsorbed myoglobin to IgG, HSA and hemoglobin was found to 115.5, 230.9 and 2.5, respectively. While, in binary competition systems, myoglobin selectivity to IgG, HSA and hemoglobin was, respectively, 94.18, 98.21 and 61.09%. Rebinding in natural biological matrices, i.e. human serum or urine, showed the imprinted films to have significantly greater uptake than non-imprinted films. Re-binding in undiluted urine was found to be a facile process, with the imprinting factor, i.e. the ratio of MIP to NIP binding, being determined as 37.4.     

Nitrite effect on nitrous oxide emission from denitrifying activated sludge

Laboratory-scale experiments were conducted to examine the N₂O emission during the denitrification process. For each of the 6 runs carried out, synthetic effluent was fed in a 10 l batch mixed liquor to investigate the effect of nitrite on N₂O emission and Helium was continuously bubbled through the reactor at constant rate (0.12 l/min) to favour N₂O transfer and detection. An increasing COD/NO₃⁻-N influent ratio from 3 to 7 was firstly applied (runs 1–3). Secondly, NO₂⁻ pulse additions were performed during run 4 and 5 (10 and 20 mg N/l, respectively). Finally, the reactor was fed with influent containing both NO₂⁻ and NO₃⁻. We showed that N₂O emission was detected shortly after NO₂⁻ accumulation, few minutes after the substrate feeding. The highest emission occurred at the lower COD/NO₃⁻-N ratio (=3) and at the higher NO₂⁻ addition (20 mg N/l). In addition, the higher nitrogen conversion to N₂O gas (14.4%) was obtained with an influent containing initially both NO₂⁻ and NO₃⁻. Our results suggest a direct effect of the NO₂⁻ concentration on the N₂O emission. We have also confirmed the inhibitory effect of NO₂⁻ concentration on N₂O reduction.     

Electrochemical quartz crystal impedance study on the overoxidation of polypyrrole-carbon nanotubes composite film for amperometric detection of dopamine

The electrochemical quartz crystal impedance (EQCI) method was used to study the overoxidation of polypyrrole (PPy)–multiwalled carbon nanotubes (MWCNT) nanocomposite film in neutral and alkaline solutions. The values of molar mass per electron transferred (M/n) obtained during the overoxidation of PPy in 0.10 mol L⁻¹ Na₂SO₄ and 0.20 mol L⁻¹ NaOH aqueous solutions were estimated to be ca. 17 and 22 g mol⁻¹, respectively, suggesting the nucleophilic attack of solution OH⁻ to the pyrrole units during the overoxidation, and the possible partial formation of carboxylic groups after the overoxidation in the NaOH solution. Also, the overoxidized PPy–MWCNT composite film prepared in the NaOH solution showed a notably larger affinity to dopamine (DA) dissolved in a neutral phosphate buffer than that prepared in the Na₂SO₄ solution. The modification of the overoxidized nanocomposite film improved substantially the sensitivity for DA assay in a neutral phosphate buffer, as compared with the modification of overoxidized PPy or MWCNT alone. At a −6 kHz (201-nm thickness) nanocomposite film prepared in a polymerization bath containing 1.0 mg mL⁻¹ MWCNT and overoxidized in 0.20 mol L⁻¹ aqueous NaOH, the peak current response from differential pulse voltammetric assay of DA was linear with DA concentration from 4.0 × 10⁻⁸ to 1.4 × 10⁻⁶ mol L⁻¹, with a lower limit of detection of 1.7 nmol L⁻¹, good anti-interferent ability, as well as good stability and reproducibility.     

Effect of oxygen supply on cell growth and saponin production in bioreactor cultures of Panax ginseng

The effects of oxygen supply within the range 20.8–50% (using pure oxygen and air), on cell cultures of Panax ginseng were investigated in a balloon-type bubble bioreactor (5 L capacity, containing 4 L Murashige and Skoog medium, supplemented with 7.0 mg L⁻¹ indolebutyric acid, 0.5 mg L⁻¹ kinetin and 30 g L⁻¹ sucrose). A 40% oxygen supply was found to be optimal for the production of both cell mass and saponin yielding values of 12.8 g (DW) L⁻¹, 4.5 mg (g DW)⁻¹ on day 25, respectively. Low (20.8%, 30%) and high (50%) oxygen concentration supplies were unfavorable to cell growth and saponin accumulation. The results indicate that oxygen supplementation to bioreactor-based ginseng cultures was beneficial for biomass accumulation and saponin production.     

Embryonic inheritance of the chromatin organisation of the imprinted H19 domain in mouse spermatozoa

Insulin-like growth factor 2 (Igf 2) and H19 genes are oppositely imprinted and as such have been most extensively studied imprinted genes both genetically and at the molecular level. Imprints of the H19 gene, being established during spermatogenesis, are epigenetically transmitted to the somatic cells of the embryo. Current hypotheses attempting to explain the allele-specific silence of the H19 gene include DNA methylation and chromatin condensation. In order to understand the molecular basis of H19 epigenesis, it is crucial to identify the markings in the chromatin organising the imprinted domain in spermatozoa. Using Micrococcal nuclease (MNase), DNase I and Methidiumpropyl-EDTA. iron II (MPE·Fe(II)) as chromatin probes, we demonstrate that in mouse epididymal spermatozoa, at least 4 kb DNA upstream of the H19 ‘cap’ site, containing the imprinted and differentially methylated domain (DMD), is heterochromatic. The cleavage sites in this domain (−2 to −4 kb) exhibit ~425 bp periodicity. This structure is maintained in the paternal allele of normal embryos and is disrupted at −2.2, −2.65 and at −3.5 kb in embryos maternally disomic for the distal end of chromosome 7 (MatDp 7). The hypersensitive sites in chromatin precisely register the MPE·Fe(II) cleavage sites in chromosomal DNA. Therefore, the DNA sequences in the imprinted domain constrain the chromatin structure in a way similar to that of 1.688 g/cm³ Drosophila satellite chromatin. In addition, we find that condensation of the paternal allele correlates with methylation-dependent alteration in the structure of DNA sequences in DMD. These results suggest that CpG-methylation induces localised changes in DNA conformation and these facilitate consequent remodelling of chromatin thereby allowing the paternal and maternal H19 alleles to be distinguished.     

Epinephrine quantification in pharmaceutical formulations utilizing plant tissue biosensors

A plant tissue biosensor associated with flow injection analysis is proposed to determine epinephrine in pharmaceutical samples. The polyphenol oxidase enzymes present in the fibers of a palm tree fruits (Livistona chinensis), catalyses the oxidation of epinephrine to epinephrinequinone as a primary product. This product is then electrochemically reduced (at −0.10 V versus Ag/AgCl_sat) on the biosensor surface and the resulting current is used for the quantification of epinephrine. The biosensor provides a linear response for epinephrine in the concentration range from 5.0 × 10⁻⁵ to 3.5 × 10⁻⁴ mol l⁻¹. The limit of detection estimated for this interval was 1.5 × 10⁻⁵ mol l⁻¹ and the correlation coefficient of 0.998, working under a flow rate of 2.0 ml min⁻¹ and using a sample loop of 100 μl. The repeatability (R.S.D. for 10 consecutive determinations of a 3.0 × 10⁻⁴ mol l⁻¹ epinephrine solution) was 3.1%. The results obtained by the method here proposed were compared with the official UV spectrophotometric procedure and also using a plant tissue reactor. The responses obtained with the proposed strategies were in good agreement with both ways of analyses, whereas the values obtained by the official spectrophotometric method was strongly affected by benzoic acid, present in the formulation of pharmaceutical product utilized for inhalation. Such favorable results obtained with the carbon paste biosensor or utilizing the bioreactor, joined with the simplicity of its preparation turns these procedures very attractive for epinephrine quantification in pharmaceutical products.     

Enhancement of growth and gymnodimine production by the marine dinoflagellate, Karenia selliformis

Because of its novel bioactive properties the production of gymnodimine for use as a pharmaceutical precursor has aroused interest. The dinoflagellate, Karenia selliformis produces gymnodimine when grown in bulk culture using GP + selenium medium but the growth rates (μ) and levels of gymnodimine are low (μ, 0.05 days⁻¹; gymnodimine 250 μg L⁻¹ max). We describe the effects of organic acid additions (acetate, glycolate, alanine and glutamate additions and combinations of these) in enhancing growth and gymnodimine production in axenic cultures. The most effective organic acid combinations in decreasing order were: glycolate/alanine > acetate > glycolate. Glycolate/alanine optimised gymnodimine production by prolonging growth (maximum cell yield, 1.76 × 10⁵ cells mL⁻¹; gymnodimine, 1260 μg L⁻¹; growth rate (μ), 0.2 days⁻¹) compared to the control (growth maximum cell yield, 7.8 × 10⁴ cells mL⁻¹; gymnodimine, 780 μg L⁻¹; μ, 0.17 days⁻¹). Acetate enhanced gymnodimine by stimulating growth rate (μ, 0.23 days⁻¹) and the large concentration of gymnodimine per cell (16 pg cell⁻¹ cf. 9.8 pg cell⁻¹ for the control) suggests a role for this compound in gymnodimine biosynthesis. Amending culture media with Mn²⁺ additions resulted in slightly decreased growth in control cultures and increased the gymnodimine while in glycolate/alanine cultures growth was stimulated but gymnodimine production decreased. The results suggest that the organic acid can enhance gymnodimine production by either enhancing growth maximum or the biosynthetic pathway.     

A performance comparison of choline biosensors: anodic or cathodic detections of H2O2 generated by enzyme immobilized on a conducting polymer

Amperometric choline biosensors were fabricated by the covalent immobilization of an enzyme of choline oxidase (ChO) and a bi-enzyme of ChO/horseradish peroxidase (ChO/HRP) onto poly-5,2′:5′,2″-terthiophene-3′-carboxylic acid (poly-TTCA) modified electrodes (CPMEs). A sensor modified with ChO utilized the oxidation process of enzymatically generated H₂O₂ in a choline solution at +0.6 V. The other one modified with ChO/HRP utilized the reduction process of H₂O₂ in a choline solution at −0.2 V. Experimental parameters affecting the sensitivity of sensors, such as pH, applied potential, and temperature were optimized. A performance comparison of two sensors showed that one based on ChO/HRP/CPME had a linear range from 1.0×10⁻⁶ to 8.0×10⁻⁵ M and the other based on ChO/CPME from 1.0×10⁻⁶ to 5.0×10⁻⁵ M. The detection limits for choline employing ChO/HRP/CPME and ChO/CPME were determined to be about 1.0×10⁻⁷ and 4.0×10⁻⁷ M, respectively. The response time of sensors was less than 5 s. Sensors showed good selectivity to interfering species. The long-term storage stability of the sensor based on ChO/HRP/CPME was longer than that based on ChO/CPME.     

Poly-beta-hydroxybutyrate accumulation in Nostoc muscorum and Spirulina platensis under phosphate limitation

Nostoc muscorum and Spirulina platensis were grown under phosphate deficiency in order to investigate the role of internal phosphate pool and activity of alkaline phosphatase on poly-β-hydroxybutyrate (PHB) accumulation. PHB accumulation in N. muscorum increased to 22.7% of dry weight (dw) after 4 day of phosphate deficiency, while the internal phosphate pool reduced to the level of 0.02 μM mg dw⁻¹ at a maximum APase activity of 2.57 nM PNP mg dw⁻¹ h⁻¹. In contrary, S. platensis depicted maxima of 1.39 nM PNP mg dw⁻¹ h⁻¹ on day 30 of incubation, which was about 2 fold lower than the observed value of N. muscorum. PHB content in S. platensis remained low even after prolonged phosphate starvation, and a rise only up to 3.5% of dw was recorded on day 60 of phosphate deficiency. Supplementation of NADPH exogenously to S. platensis cultures grown under phosphate deficiency favoured PHB accumulation in 10, 20 and 30 days old cultures, but not in the cultures grown under phosphate deficiency for 60 days. The possible role of phosphate limitation on PHB accumulation is discussed.     

Metal accumulation by Halodule wrightii populations

Metal concentrations and population parameters of the seagrass Halodule wrightii were determined at three locations at Rio de Janeiro State, Brazil. The possible increase of metal availability in one of these areas, Sepetiba Bay, as a result of dredging of contaminated bottom sediments which ocurred, was evaluated by analyses of Al, Cd, Cr, Cu, Fe, Ni, Pb and Zn in root, rhizome and shoots. In addition, analyses were carried out in H. wrightii populations from non-contaminated areas located at northwestern (Cabo Frio) and southeastern (Angra do Reis) regions of Rio de Janeiro State. Concurrently, abundance and density data of the seagrass populations were obtained. It was found that concentration from Sepetiba Bay samples up to 1.6 ± 0.4 μg g⁻¹ of Cd, 12 ± 1.0 μg g⁻¹ of Cr, 27 ± 2.4 μg g⁻¹ of Pb, 291 ± 47 μg g⁻¹ of Mn, 128 ± 23 μg g⁻¹ of Zn were significantly higher than that from two other collection sites. An increase in Cd and Zn concentration was observed in H. wrightii from Sepetiba Bay indicating that metal mobilization from contaminated sediments through dredging activities were, at least in part, transferred to the biotic compartment via accumulation by the seagrass. The populations of seagrass within the region demonstrated quite substantial changes in biomass data but not in shoot or rhizome density during the study. Such changes in biomass are to be expected, as these dynamics are typical of the small, isolated monospecific populations of H. wrightii along the Rio de Janeiro coast.     

Immobilization of horseradish peroxidase on chitosan/silica sol-gel hybrid membranes for the preparation of hydrogen peroxide biosensor

A simple and effective strategy for fabrication of hydrogen peroxide (H₂O₂) biosensor has been developed by entrapping horseradish peroxidase (HRP) in chitosan/silica sol–gel hybrid membranes (CSHMs) doped with potassium ferricyanide (K₃Fe(CN)₆) and gold nanoparticles (GNPs) on platinum electrode surface. The hybrid membranes are prepared by cross-linking chitosan (CS) with 3-aminopropyltriethoxysilane (APTES), while the presence of GNPs improved the conductivity of CSHMs, and the Fe(CN)₆^3−/4− was used as a mediator to transfer electrons between the electrode and HRP due to its excellent electrochemistry activity. UV–Vis absorption spectroscopy was employed to characterize the different components in the CSHMs and their interaction. The parameters influencing the performance of the resulting biosensor were optimized and the characteristic of the resulting biosensor was characterized by cyclic voltammetry and chronoamperometry. Linear calibration for hydrogen peroxide was obtained in the range of 3.5 × 10^− 6 to 1.4 × 10^− 3 M under the optimized conditions with the detection limit (S/N = 3) of 8.0 × 10^− 7 M. The apparent Michaelis–Menten constant of the enzyme electrode was 0.93 mM. The enzyme electrode retained about 78% of its response sensitivity after 30 days. The system was applied for the determination of the samples, and the results obtained were satisfactory.     

Bench-scale fermentation of Trichoderma viride on wastewater sludge: Rheology, lytic enzymes and biocontrol activity

Conidiation and lytic enzyme production by Trichoderma viride at different solids concentration of pre-treated municipal wastewater sludge was examined in a 15-L fermenter. The maximum conidia concentration (5.94 × 10⁷ CFU mL⁻¹ at 96 h) was obtained at 30 g L⁻¹ suspended solids. The maximum lytic enzyme activities were achieved around 12–30 h of fermentation. Bioassay against a fungal phytopathogen, Fusarium sp. showed maximum activity in the sample drawn around 96 h of fermentation at 30 g L⁻¹ suspended solids concentration. Entomotoxicity against spruce budworm larvae showed maximum value ≈17290 SBU μL⁻¹ at 30 g L⁻¹ suspended solids concentration at the end of fermentation (96 h). Plant bioassay showed dual action of T. viride, i.e., disease prevention and growth promotion. The rheological analyses of fermentation sludges showed the pseudoplastic behaviour. In order to maintain required dissolved oxygen concentration ≥30%, the agitation and aeration requirements significantly increased at 35 g L⁻¹ compared to 30 and 25 g L⁻¹. The oxygen uptake rate and volumetric oxygen mass transfer coefficient, k_La at 35 g L⁻¹ did not increase in comparison to 30 g L⁻¹ due to rheological complexity of the broth during fermentation. Thus, the successful fermentation operation of the biocontrol fungus T. viride is a rational indication of its potential for mass-scale production for agriculture and forest sector as a biocontrol agent.     

Binding of genistein to human serum albumin demonstrated using tryptophan fluorescence quenching

Genistein is an isoflavone and phytoestrogen that is a potent inhibitor of cell proliferation and angiogenesis. This study was designed to investigate the binding of genistein to human serum albumin (HSA) under physiological conditions with drug concentrations in the range of 6.7 × 10⁻⁶ to 2.0 × 10⁻⁵ mol L⁻¹ and HSA concentration at 1.5 × 10⁻⁶ mol L⁻¹. Fluorescence quenching methods in combination with Fourier transform infrared (FT-IR) spectroscopy and circular dichroism (CD) spectroscopy was used to determine the binding mode, the binding constant and the protein structure changes in the presence of genistein in aqueous solution. Changes in the CD spectra and FT-IR spectra were observed upon ligand binding, and the degree of tryptophan fluorescence quenching change did significantly in the complexes. These data have proved the change in protein secondary structure accompanying ligand binding. The change in tryptophan fluorescence intensity was used to determine the binding constants. The thermodynamic parameters, the enthalpy change (ΔH) and the entropy change (ΔS) were calculated to be −22.24 kJ mol⁻¹and 19.60 J mol⁻¹ K⁻¹ according to the van’t Hoff equation, which indicated that hydrophobic and electrostatic interactions play the main role in the binding of genistein to HSA.     

A numerical and experimental study of compliance and collapsibility of preterm lamb tracheae

Knowledge of the mechanical behaviour of immature tracheae is crucial in order to understand the effects exerted on central airways by ventilatory treatments, particularly of Total Liquid Ventilation. In this study, a combined experimental and computational approach was adopted to investigate the compliance and particularly collapsibility of preterm lamb tracheae in the range of pressure likely applied during Total Liquid Ventilation (−30 to 30 cmH₂O). Tracheal samples of preterm lambs (n=5; gestational age 120–130 days) were tested by altering transmural pressure from −30 to 30 cmH₂O. Inflation (S_i) and collapsing (S_c) compliance values were calculated in the ranges 0 to 10 cmH₂O and –10 to 0 cmH₂O, respectively. During the tests, an asymmetric behaviour of the ΔV/V₀ vs. P curves at positive and negative pressure was observed, with mean S_i=0.013 cmH₂O⁻¹ and S_c=0.053 cmH₂O⁻¹. A different deformed configuration of the sample regions was observed, depending on the posterior shape of cartilaginous ring. A three-dimensional finite-element structural model of a single tracheal ring, based on histology measurements of the tested samples was developed. The model was parameterised in order to represent rings belonging to three different tracheal regions (craniad, median, caudal) and numerical analyses replicating the collapse test conditions were performed to evaluate the ring collapsibility at pressures between 0 and −30 cmH₂O. Simulation results were compared to experimental data to verify the model's reliability. The best model predictions occurred at pressures −30 to −10 cmH₂O. In this range, a model composed of median rings best interpreted the experimental data, with a maximum error of 2.7%; a model composed of an equal combination of all rings yielded an error of 12.6%.     

Supported bilayer lipid membranes modified with a phosphate ionophore

This article reports the electrical responses of a phosphate ionophore, the cyclic polyamine 3-decyl-1,5,8-triazacyclodecane-2,4-dione (N₃-cyclic amine) incorporated into metal supported bilayer lipid membranes (s-BLM). Teflon coated silver wire was used as a support. In a potentiometric mode, the ionophore had a response that was linearly related to the logarithm of HPO₄²⁻ concentration and was also dependant on pH. Selectivity coefficients for other anions compared to HPO₄²⁻ ions, determined by the separate solution method, fell within the range 1.73 × 10⁻⁴ to 6.38 × 10⁻².     

A study in UF-membrane reactor on activity and stability of nitrile hydratase from Microbacterium imperiale CBS 498-74 resting cells for propionamide production

The bioconversion of propionitrile to propionamide was catalysed by nitrile hydratase (NHase) using resting cells of Microbacterium imperiale CBS 498-74 (formerly, Brevibacterium imperiale). This microorganism, cultivated in a shake flask, at 28 °C, presented a specific NHase activity of 34.4 U mg_DCW⁻¹ (dry cell weight). The kinetic parameters, K_m and V_max, tested in 50 mM sodium phosphate buffer, pH 7.0, in the propionitrile bioconversion was evaluated in batch reactor at 10 °C and resulted 21.6 mM and 11.04 μmol min⁻¹ mg_DCW⁻¹, respectively. The measured apparent activation energy, 25.54 kJ mol⁻¹, indicated a partial control by mass transport, more likely through the cell wall.

UF-membrane reactors were used for kinetic characterisation of the NHase catalysed reaction. The time dependence of enzyme deactivation on reaction temperature (from 5 to 25 °C), on substrate concentrations (from 100 to 800 mM), and on resting cell loading (from 1.5 to 200 μg  ml⁻¹) indicated: lower diffusional control (E_a=37.73 kJ mol⁻¹); and NHase irreversible damage caused by high substrate concentration. Finally, it is noteworthy that in an integral reactor continuously operating for 30 h, at 10 °C, 100% conversion of propionitrile (200 mM) was attained using 200 μg  ml⁻¹ of resting cells, with a maximum volumetric productivity of 0.5 g l⁻¹ h⁻¹.     

Trapping, loss and annihilation of excitations in a photosynthetic system: II. Experiments with the purple bacteria Rhodospirillum rubrum and Rhodopseudomonas capsulata

In this paper a number of experiments with the purple bacteria Rhodospirillum rubrum and Rhodopseudomonas capsulata is described in which the total fluorescence yield and/or the total fraction of reaction centers closed after a picosecond laser pulse were measured as a function of the pulse intensity. The conditions were such that the reaction centers were either all in the open or all in the closed state before the pulse arrived. These experiments are analysed using the theoretical formalism discussed in the preceding paper (Den Hollander, W.T.F., Bakker J.G.C., and Van Grondelle, R., Biochim. Biophys. Acta 725, 492–507). From the experimental results the number of connected photosynthetic units, λ, the rate of energy transfer between neighboring antenna molecules, k_h, and the rate of trapping by an open reaction center, k^o_t, can be estimated. For R. rubrum it is found that λ = 14−17, k_h = (1−2)·10¹² s⁻¹ and k^o_t = (4−6)·10¹¹ s⁻¹, for Rps. capsulata λ ≈ 30, k_h ≈ 4·10¹¹ s⁻¹ and k^o_t ≈ 3·10¹¹ s⁻¹. The findings are discussed in terms of current models for the structure of the antenna and the kinetic properties of the decay processes occurring in these purple bacteria.     

Human fibroblast culture on a crosslinked dermal porcine collagen matrix

The use of a novel porcine-derived collagen biomaterial as a dermal tissue engineering matrix was examined. The matrix is derived from porcine dermis, and is processed to retain the native collagen (Type 1) and elastin structure. Human primary fibroblasts were cultured on the matrix to examine its potential for creating a dermal replacement. Attachment of fibroblasts on the collagen was compared to tissue culture plastic and PET membranes. Cell proliferation was assessed using the MTT assay and DAPI staining. For seeding densities of 5×10⁴ and 1×10⁵ cells cm⁻², PET and plastic demonstrated >95% attachment of seeded numbers after 3 h. The collagen matrix reached levels >80% after 3–4 h with no influence of the seeding density. Matrix samples with perforating pores of 40 μm diameter were also studied. After 216 h culture in static culture, with media replacement every 3 days, the final cell numbers reached 2.1×10⁵ (perforated) and 2.0×10⁵ cells cm⁻² (unperforated). In comparison fibroblast culture in a perfusion bioreactor, with continuous media replacement, reached 2.3×10⁵ (unperforated) and 2.5×10⁵ cells cm⁻² (perforated) after 216 h.     

Synthesis, characterization and swelling studies of pH responsive psyllium and methacrylamide based hydrogels for the use in colon specific drug delivery

In order to utilize the psyllium husk a medicinally important natural polysaccharide and to develop the novel hydrogels meant for the colon specific drug delivery, we have prepared psyllium and methacrylamide based polymeric networks by using N,N′-methylenebisacrylamide (NN-MBAAm) as crosslinker and ammonium persulfate (APS) as initiator. To study various structural aspects of the polymeric networks thus formed psy-cl-poly(MAAm), these were characterized with SEMs, FTIR, TGA and swelling studies. The swelling studies of networks were carried out as a function of time, temperature, pH and [NaCl]. Equilibrium swelling has been observed to depend on both composition of the polymer and nature of swelling medium. Maximum percent swelling 1262 was observed for the polymeric network prepared with 19.45 × 10⁻³ mol/L of [NN-MBAAm] at 40 °C in 0.5 M NaOH solution. This article also discusses the release dynamics of tetracycline hydrochloride from the hydrogels, for the evaluation of the drug release mechanism and diffusion coefficients of drug from the polymer matrix. The effect of pH on the release pattern of tetracycline hydrochloride has been studied by varying the pH of the release medium. It has been observed from the release dynamics of drug from the hydrogels that the diffusion exponent ‘n’ have 0.477, 0.423 and 0.427 values and gel characteristic constant ‘k’ have 5.07 × 10⁻², 6.34 × 10⁻² and 6.38 × 10⁻² values, respectively, in distilled water, pH 2.2 buffer and pH 7.4 buffer solution. The values the ‘n’ indicated that the Fickian type diffusion mechanism occurred for the release of tetracycline hydrochloride from drug loaded psy-cl-poly(MAAm) polymers in different release mediums. In Fickian type diffusion mechanism, the rate of polymer chain relaxation is more as compare to the rate of drug diffusion from these hydrogels and release behavior follows Fick’s law of diffusion. In each release medium, the values of the initial diffusion coefficient ‘D_i’ for the release of tetracycline hydrochloride was higher than the values of late time diffusion coefficient ‘D_L’ indicating that in the start, the diffusion of drug from the polymeric matrix was faster as compare to the latter stages.