Benchmarking of commercially available CHO cell culture media for antibody production

In this study, eight commercially available, chemically defined Chinese hamster ovary (CHO) cell culture media from different vendors were evaluated in batch culture using an IgG-producing CHO DG44 cell line as a model. Medium adaptation revealed that the occurrence of even small aggregates might be a good indicator of cell growth performance in subsequent high cell density cultures. Batch experiments confirmed that the culture medium has a significant impact on bioprocess performance, but high amino acid concentrations alone were not sufficient to ensure superior cell growth and high antibody production. However, some key amino acids that were limiting in most media could be identified. Unbalanced glucose and amino acids led to high cell-specific lactate and ammonium production rates. In some media, persistently high glucose concentrations probably induced the suppression of respiration and oxidative phosphorylation, known as Crabtree effect, which resulted in high cell-specific glycolysis rates along with a continuous and high lactate production. In additional experiments, two of the eight basal media were supplemented with feeds from two different manufacturers in six combinations, in order to understand the combined impact of media and feeds on cell metabolism in a CHO fed-batch process. Cell growth, nutrient consumption and metabolite production rates, antibody production, and IgG quality were evaluated in detail. Concentrated feed supplements boosted cell concentrations almost threefold and antibody titers up to sevenfold. Depending on the fed-batch strategy, fourfold higher peak cell concentrations and eightfold increased IgG titers (up to 5.8 g/L) were achieved. The glycolytic flux was remarkably similar among the fed-batches; however, substantially different specific lactate production rates were observed in the different media and feed combinations. Further analysis revealed that in addition to the feed additives, the basal medium can make a considerable contribution to the ammonium metabolism of the cells. The glycosylation of the recombinant antibody was influenced by the selection of basal medium and feeds. Differences of up to 50 % in the monogalacto-fucosylated (G1F) and high mannose fraction of the IgG were observed.     

Continuous fermentation of wheat-supplemented lignocellulose hydrolysate with different types of cell retention

Medium supplementation and process alternatives for fuel ethanol production from dilute acid lignocellulose hydrolysate were investigated. Dilute acid lignocellulose hydrolysate supplemented with enzymatically hydrolysed wheat flour could sustain continuous anaerobic cultivation of Saccharomyces cerevisiae ATCC 96581 if further supplemented with ammonium sulphate and biotin. This medium composition allowed for a hexose utilisation of 73% and an ethanol production of 36 mmol l(-1) h(-1) in chemostat cultivation at dilution rate 0.10 h(-1). Three different methods for cell retention were compared for improved fermentation of supplemented lignocellulose hydrolysate: cell recirculation by filtration, cell recirculation by sedimentation and cell immobilisation in calcium alginate. All three cell retention methods improved the hexose conversion and increased the volumetric ethanol production rate. Recirculation of 75% of the bioreactor outlet flow by filtration improved the hexose utilisation from 76% to 94%. Sedimentation turned out to be an efficient method for cell separation; the cell concentration in the reactor was 32 times higher than in the outflow after 60 h of substrate feeding. However, chemostat and continuous cell recirculation cultures became severely inhibited when the dilution rate was increased to 0.20 h(-1). In contrast, an immobilised system kept producing ethanol at a stable level also at dilution rate 0.30 h(-1).     

Metabolism of hybridoma cells and antibody secretion at high cell densities in dialysis tubing.

The experimental setup, consisting of a bundle of dialysis tubing 2.5 mm in diameter [10-15 kD cutoff, mean pore size 25 A, 20 microns (dry) and 40 microns (wet) wall thickness] inserted into a 1-l glass bioreactor supplied with oxygen and pH electrodes, a porous gas distributor, a sampling tube, and a holder for the eight pieces of dialysis tubing, was developed to investigate the properties and the microenvironment of hybridoma cells enclosed in the tubing during their batch cultivation. The concentrations of low-molecular-weight medium components were the same inside and outside the tubing, and it was possible to control the microenvironment of the cells in the tubing easily. The cell damage caused by mechanical stress was less in the dialysis tubing than in stirred spinner flasks. The influence of the initial cell density in the range from 4 X 10(5) to 1 X 10(8) cells ml-1 and the cultivation time were evaluated according to the total and viable cell concentrations and the cell/cell fragment size distributions. Furthermore, the cell membrane properties, glucose consumption rate, lactate, ammonia and lipid storage material, and the monoclonal antibody production rates as well as intracellular enzyme activities in the culture medium were measured and compared to those in reference cultures in spinner flasks with the same inoculum at low initial cell densities. In dialysis tubing in a concentration range of 5 X 10(6) to 10(8) cells ml-1, the total and viable concentrations of cells remained the same during cultivation.(ABSTRACT TRUNCATED AT 250 WORDS)     

Enhancement of antibody production by growth factor addition in perfusion and hollow-fiber culture systems

The effects of the high-molecular-weight growth factors, transferrin and bovine serum albumin (BSA), on antibody production were analyzed quantitatively in continuous hollow-fiber cultivation over a period of 60 days. Transferrin enhanced cell growth but had no significant effect on the specific antibody production rate, whereas BSA significantly enhanced antibody production. The antibody production rate was increased 4- and 14-fold respectively by feeding BSA at 2 and 5 g L(-1) into the EC side of the system (the side connected to the cell-containing outer part of the hollow-fiber unit) compared with the production achieved without BSA. Addition of 5 g L(1) BSA into the IC side of the system (the side connected to the inner part of the hollow-fiber unit) resulted in a 2.5-fold increase in the antibody production rate. The effect of BSA was also analyzed using the perfusion culture system with a separation unit. When fresh medium containing either 2 or 5 g L(-1) BSA was fed into the reactor, both the specific growth rate and specific death rate increased, while the specific antibody production rate was increased 2- and 25-fold, respectively, by feeding BSA at these two concentrations compared with no addition. Comparing the two systems, the increase in the antibody production rate achieved with the hollow-fiber system was threefold greater than that in the perfusion culture system with the same concentration of BSA feeding. (c) 1995 John Wiley & Sons, Inc.     

Monoclonal antibody production in dialyzed continuous suspension culture

Hybridoma cell growth and monoclonal antibody production in dialyzed continuous suspension culture were investigated using a 1.5-L Celligen bioreactor. Medium supplemented with 1.5% fetal bovine serum was fed directly into the reactor at a dilution rate of 0.45 d(-1). Dailysis tubing with a molecular weight cut-off (MWCO) of 1000 was coiled inside the bioreactor. Fresh medium containing no serum or serum substitues passed through the dialysis tubing at flow rates of 2 to 5 L/d. The objective was to remove low molecular weight inhibitors, such as lactic acid and ammonia, by diffusion through the tubing, while continuoulsy replenishing essential nutrients by the same mechanism. Due to the low MWCO of the dialysis tubing high molecular weight components such as growth factors and antibody were not removed by the dialyzing stream. In the batch start-up phase, the monoclonal antibody (MAb) titer was almost 3 times that achieved in typical batch cultures (i.e., 170 to 180 mg/L). During dialyzed continuous operation, a substantial increase (up to 40%) in cell density, monoclonal antibody (MAb) titer, and reactor MAb productivity was observed, as compared with a conventional continuous suspension culture. The cell viability and the specific MAb productivity remained practically constant at different dialysis rates. This finding suggests that the steady state growth and death rate in continuous suspension hybridoma cultures are not direct functions of the nutrient or inhibitor concentrations.     

A high-yielding, generic fed-batch cell culture process for production of recombinant antibodies

A fed-batch cell culture process was developed that has general applicability to all evaluated Sp2/0 (n = 8) and NS0 (n = 1) antibody-producing cell lines. The two key elements of this generic process were a protein-free concentrated feed medium, and a robust, metabolically responsive feeding strategy based on the off-line measurement of glucose. The fed-batch process was shown to perform equivalently at the 15 L development scale and 750 L manufacturing scale. Compared to batch cultures, the fed-batch process yielded a 4. 3 fold increase in the average integral of viable cell concentration and a 1.7 fold increase in average specific antibody production rate, equivalent to a 7.6 fold increase in average final antibody concentration. The highest producing cell line reached a peak viable cell concentration of 1.0 x 10(7) cell mL(-1) and a final antibody concentration of 750 mg L(-1) in a 10 day process. For all lines evaluated, reducing bioreactor pH set point from 7.2 to 7.0 resulted in an additional 2.4 fold increase in average final antibody concentration. The optimized fed-batch process consistently yielded a volumetric productivity exceeding 50 mg L(-1) day(-1). This generic, high-yielding fed-batch process significantly decreased development time, and increased manufacturing efficiency, thereby facilitating the clinical evaluation of numerous recombinant antibodies.     

Comparison of cell growth in T-flasks, in micro hollow fiber bioreactors, and in an industrial scale hollow fiber bioreactor system

In this article, cell growth in a novel micro hollow fiberbioreactor was compared to that in a T-flask and theAcuSyst-Maximizer®, a large scale industrial hollowfiber bioreactor system. In T-flasks, there was relativelylittle difference in the growth rates of one murine hybridomacultured in three different media and for three other murinehybridomas cultured in one medium. However, substantialdifferences were seen in the growth rates of cells in themicro bioreactor under these same conditions. These differencecorrelated well with the corresponding rates of initial cellexpansion in the Maximizer. Quantitative prediction of thesteady-state antibody production rate in the Maximizer was moreproblematic. However, conditions which lead to faster initialcell growth and higher viable cell densities in the microbioreactor correlated with better performance of a cell line inthe Maximizer. These results demonstrate that the microbioreactor is more useful than a T-flask for determining optimalconditions for cell growth in a large scale hollow fiberbioreactor system.     

Milking microalga Dunaliella salina for beta-carotene production in two-phase bioreactors

A new method was developed for production of beta-carotene from Dunaliella salina. Cells were grown in low light intensity and then transferred to a production bioreactor illuminated at a higher light intensity. It was a two-phase bioreactor consisting of an aqueous and a biocompatible organic phase. Mixing of the cells and extraction were performed by recirculation of the organic phase. Two experiments were performed. In the first experiment, bioreactors were operated at two different solvent recirculation rates of 150 and 200 mL min(-1). The beta-carotene extraction rate increased significantly at the higher recirculation rate, without exerting any influence on cell number and viability. A second experiment was carried out at a recirculation rate (200 mL min(-1)) appropriate for the study of long-term production of beta-carotene. The results show that D. salina at high light intensity remained viable for a long period (>47 days) in the presence of a biocompatible organic phase; however, cell growth was very slow. beta-Carotene could be continuously extracted to the organic phase; the cells continued to produce beta-carotene and the extracted molecules were continuously reproduced. As a result, beta-carotene was continuously removed ("milked") from the cells. beta-Carotene extraction efficiency in this system was >55%, and productivity was 2.45 mg m(-2) day(-1), much higher than that of commercial plants.     

Effect of feed and bleed rate on hybridoma cells in an acoustic perfusion bioreactor: part I. Cell density, viability, and cell-cycle distribution

For the development of optimal perfusion processes the effect of the feed and bleed rate on cell growth in a perfusion bioreactor was studied. The viable-cell density, viability, growth, death, and lysis rate and cell-cycle distribution of a hybridoma cell line producing an IgG1 were studied over a range of specific feed and bleed rates. It was found that the feed and bleed rates applied in the different cultures could be divided into two regions based on the viable-cell density and cell-cycle distribution. The cultures in the first region, low feed rates (0.5 and 1.0 d(-1)) combined with low bleed rates (0.05 and 0.10 d(-1)), were nutrient-limited, as an increase in the feed rate resulted in an increase in the viable-cell density. The cultures in the second region, high feed and bleed rates, were nonnutrient-limited. In this region the viable-cell density decreased more or less linearly with an increase in the bleed rate and was independent of the feed rate. This suggests that the cells were limited by a cell-related factor. Comparison of Trypan-blue dye-exclusion measurements and lactate-dehydrogenase activity measurements revealed that cell lysis was not negligible in this bioreactor set-up. Therefore, lactate-dehydrogenase activity measurements were essential to measure the death rate accurately. The specific growth rate was nearly constant for all tested conditions. The viability increased with an increase of the bleed rate and was independent of the feed rate. Furthermore, the specific productivity of monoclonal antibody was constant under all tested conditions. For the optimal design of a perfusion process it should first be established whether viability is an important parameter. If not, a bleed rate as low as possible should be chosen. If low viabilities are to be avoided, the bleed rate chosen should be higher, with the value depending on the desired viability. Next, the feed rate should be set at such a rate that the cells are just in the nonnutrient-limited region.     

New miniaturized hollow-fiber bioreactor for in vivo like cell culture, cell expansion, and production of cell-derived products

We have developed a miniaturized hollow-fiber bioreactor system for mammalian cell culture with a volume of 1 mL. Cell and medium compartments of the bioreactor are separated by a semipermeable membrane, and oxygenation of the cell compartment is accomplished using an oxygenation membrane. As a result of the geometry of the transparent housing, cells can be observed by microscopy during culture. The leukemic cell lines CCRF-CEM, HL-60, and REH were cultivated up to densities of 3.5 x 10(7)/mL without medium change or manipulation of the cells. As shown using CCRF-CEM cells, growth in the bioreactor was strongly influenced and could be controlled by the medium flow rate. As a consequence, consumption of glucose and generation of lactate varied with flow rate. Depending on the molecular size cutoff of the membranes used, added growth factors such as GM-CSF, as well as factors secreted from the cells, are retained in the cell compartment for up to 1 week. This new miniaturized hollow-fiber bioreactor offers advantages in tissue engineering by continuous nutrient supply for cells in high density, retention of added or autocrine produced factors, and undisturbed long-term culture in a closed system.     

A predictive high‐throughput scale‐down model of monoclonal antibody production in CHO cells

Multi‐factorial experimentation is essential in understanding the link between mammalian cell culture conditions and the glycoprotein product of any biomanufacturing process. This understanding is increasingly demanded as bioprocess development is influenced by the Quality by Design paradigm. We have developed a system that allows hundreds of micro‐bioreactors to be run in parallel under controlled conditions, enabling factorial experiments of much larger scope than is possible with traditional systems. A high‐throughput analytics workflow was also developed using commercially available instruments to obtain product quality information for each cell culture condition. The micro‐bioreactor system was tested by executing a factorial experiment varying four process parameters: pH, dissolved oxygen, feed supplement rate, and reduced glutathione level. A total of 180 micro‐bioreactors were run for 2 weeks during this DOE experiment to assess this scaled down micro‐bioreactor system as a high‐throughput tool for process development. Online measurements of pH, dissolved oxygen, and optical density were complemented by offline measurements of glucose, viability, titer, and product quality. Model accuracy was assessed by regressing the micro‐bioreactor results with those obtained in conventional 3 L bioreactors. Excellent agreement was observed between the micro‐bioreactor and the bench‐top bioreactor. The micro‐bioreactor results were further analyzed to link parameter manipulations to process outcomes via leverage plots, and to examine the interactions between process parameters. The results show that feed supplement rate has a significant effect (P < 0.05) on all performance metrics with higher feed rates resulting in greater cell mass and product titer. Culture pH impacted terminal integrated viable cell concentration, titer and intact immunoglobulin G titer, with better results obtained at the lower pH set point. The results demonstrate that a micro‐scale system can be an excellent model of larger scale systems, while providing data sets broader and deeper than are available by traditional methods. Biotechnol. Bioeng. 2009; 104: 1107–1120. © 2009 Wiley Periodicals, Inc.     

运用氨基酸分析法和DOE法优化抗PD-1单克隆抗体生产用培养基

本研究采用氨基酸分析法结合DOE设计法优化并获得高表达抗PD-1单克隆抗体生产用基础和补料培养基。通过对市售多种基础和补料培养基进行筛选,获得细胞生长状况较优的基础培养基和抗体表达较高的补料培养基,利用氨基酸分析法检测较优基础培养基和补料培养基中氨基酸消耗情况,确定影响细胞生长和抗体表达的关键氨基酸种类,利用DOE分析软件设计分别在较优基础和补料培养基中添加不同浓度的氨基酸种类及浓度,根据细胞生长及抗体表达,优化得到抗PD-1单克隆抗体的基础和补料培养基组合。最终优化后基础培养基配方为:Hycell CHO培养基中添加1.04 mmol/L L-天冬酰胺和0.76 mmol/L L-谷氨酰胺。最终优化后补料培养基配方为:OPM CHOCD Feed1补料培养基中添加38.7 mmol/L L-组氨酸,75.0 mmol/L L-酪氨酸,64.0 mmol/L L-丝氨酸,49.2 mmol/L L-谷氨酰胺和18.7 mmol/L L-半胱氨酸。经过3 L反应器培养验证,优化后的培养基比未优化时,最大活细胞密度(PVCD)提高了62.7%,抗PD-1单克隆抗体表达量提高了71.5%,且活性无明显差异。     

Investigation of parameters affecting a fixed bed bioreactor process for recombinant cell lines

A BHK 21 cell line expressing a recombinant antibody was grown in a fixed bed reactor (FBR) system using a porous support made of Siran glass beads. The contribution of five process variables (bead and inoculum sizes; circulation and dilution rates; glutamine concentration of the feed) to the productivity of the process (defined as production rate, effluent product concentration or yield of product on medium supplied) was investigated using a partial factorial experimental design. Individually, none of the variables tested had a significant affect upon productivity. The combination of smaller bead and inoculum sizes, higher circulation and dilution rates, plus higher feed glutamine concentration gave a markedly higher productivity than any other combination of variable levels tested. This combination of variable levels suggested that better results shold be obtained using a fluidised bed reactor system. However, comparison of the productivities of the two systems showed that the FBR gave the better results. This result can be explained in terms of the relationship of Qs_rAb to .Abbreviations C concentration - D dilution rate - FBR fixed bed bioreactor - FIBR fluidised bed bioreactor - Gln glutamine - Qs cell specific rate - Qv volumetric rate - rAb recombinant antibody - X_v viable cell density - specific growth rate     

NS0 cell damage by high gas velocity sparging in protein-free and cholesterol-free cultures

Recent developments in high cell density and high productivity fed-batch animal cell cultures have placed a high demand on oxygenation and carbon dioxide removal in bioreactors. The high oxygen demand is often met by increasing agitation and sparging rates of air/O2 in the bioreactors. However, as we demonstrate in this study, an increase of gas sparging can result in cell damage at the sparger site due to high gas entrance velocities. Previous studies have showed that gas bubble breakup at the culture surface was primarily responsible for cell damage in sparged bioreactors. Such cell damage can be reduced by use of surfactants such as Pluronic F-68 in the culture. In our results, where NS0 cells were grown in a protein-free and cholesterol-free medium containing 0.5 g/L Pluronic F-68, high gas entrance velocity at the sparger site was observed as the second mechanism for cell damage. Experiments were performed in scaled-down spinners to model the effect of hydrodynamic force resulting from high gas velocities on antibody-producing NS0 cells. Cell growth and cell death were described by first-order kinetics. Cell death rate constant increased significantly from 0.04 to 0.18 day(-1) with increasing gas entrance velocity from 2.3 to 82.9 m/s at the sparger site. The critical gas entrance velocity for the NS0 cell line studied was found to be approximately 30 m/s; velocities greater than 30 m/s caused cell damage which resulted in reduced viability and consequently reduced antibody production. Observations from a second cholesterol-independent NS0 cell line confirmed the occurrence of cell damage due to high gas velocities. Increasing the concentration of Pluronic F-68 from 0.5 to 2 g/L had no additional protective effect on cell damage associated with high gas velocity at the sparger. The results of gas velocity analysis for cell damage have been applied in two case studies of large-scale antibody manufacturing. The first is a troubleshooting study for antibody production carried out in a 600 L bioreactor, and the second is the development of a gas sparger design for a large bioreactor scale (e.g., 10,000 L) for antibody manufacturing.     

Raman-based dynamic feeding strategies using real-time glucose concentration monitoring system during adalimumab producing CHO cell cultivation

The use of Process Analytical Technology tools coupled with chemometrics has been shown great potential for better understanding and control of mammalian cell cultivations through real-time process monitoring. In-line Raman spectroscopy was utilized to determine the glucose concentration of the complex bioreactor culture medium ensuring real-time information for our process control system. This work demonstrates a simple and fast method to achieve a robust partial least squares calibration model under laboratory conditions in an early phase of the development utilizing shake flask and bioreactor cultures. Two types of dynamic feeding strategies were accomplished where the multi-component feed medium additions were controlled manually and automatically based on the Raman monitored glucose concentration. The impact of these dynamic feedings was also investigated and compared to the traditional bolus feeding strategy on cellular metabolism, cell growth, productivity, and binding activity of the antibody product. Both manual and automated dynamic feeding strategies were successfully applied to maintain the glucose concentration within a narrower and lower concentration range. Thus, besides glucose, the glutamate was also limited at low level leading to reduced production of inhibitory metabolites, such as lactate and ammonia. Consequently, these feeding control strategies enabled to provide beneficial cultivation environment for the cells. In both experiments, higher cell growth and prolonged viable cell cultivation were achieved which in turn led to increased antibody product concentration compared to the reference bolus feeding cultivation.     

Defined protein and animal component-free NS0 fed-batch culture

A chemically defined protein and animal component-free fed-batch process for an NS0 cell line producing a human IgG(1) antibody has been developed. The fed-batch feed profile was optimised in a step-wise manner. Depletion of measurable compounds was determined by direct analysis. The cellular need for non-measurable compounds was tested by continued culturing of cell suspension, removed from the bioreactor, in shake-flasks supplemented with critical substances. In the final fed-batch culture, 8.4 x 10(6) viable cells mL(-1) and 625 mg antibody L(-1) was obtained as compared to 2.3 x 10(6) cells mL(-1) and 70 mg antibody L(-1) in batch. The increase in cell density, in combination with a prolonged declining phase where antibody formation continued, resulted in a 6.2-fold increase in total cell yield, a 10.5-fold increase in viable cell hours and an 11.4-fold increase in product yield. These improvements were obtained by using a feed with glucose, glutamine, amino acids, lipids, sodium selenite, ethanolamine and vitamins. Specifically, supplementation with lipids (cholesterol) had a drastic effect on the maximum viable cell density. Calcium, magnesium and potassium were not depleted and a feed also containing iron, lithium, manganese, phosphorous and zinc did not significantly enhance the cell yield. The growth and death profiles in the final fed-batch indicated that nutrient deprivation was not the main cause of cell death. The ammonium concentration and the osmolality increased to potentially inhibitory levels, but an imbalance in the supply of growth/survival factors may also contribute to termination of the culture.     

Protein-free fed-batch culture of non-GS NS0 cell lines for production of recombinant antibodies

Presented is a novel antibody production platform based on the fed-batch culture of recombinant, NS0-derived cell lines. A standardized fed-batch cell culture process was developed for five non-GS NS0 cell lines using enriched and optimized protein-free, cholesterol-free, and chemically defined basal and feed media. The process performed reproducibly and scaled faithfully from the 2-L to the 100-L bioreactor scale achieving a volumetric productivity of > 120 mg/L per day. Fed-batch cultures for all five cell lines exhibited significant lactate consumption when the cells entered the stationary or death phase. Peak and final lactate concentrations were low relative to a previously developed fed-batch process (FBP). Such low lactate production and high lactate consumption rates were unanticipated considering the fed-batch culture basal medium has an unconventionally high initial glucose concentration of 15 g/L, and an overall glucose consumption in excess of 17 g/L. The potential of this process platform was further demonstrated through additional media optimization, which has resulted in a final antibody concentration of 2.64 +/- 0.19 g/L and volumetric productivity of > 200 mg/L per day in a 13-day FBP for one of the five production cell lines. Use of this standardized protein-free, cholesterol-free NS0 FBP platform enables consistency in development time and cost effectiveness for manufacturing of therapeutic antibodies.     

Controlling and predicting monoclonal antibody production in hollow-fiber bioreactors.

A simple optimization strategy is described which enables monoclonal antibody (MCA) production in hollow-fiber bioreactors to be controlled and predicted. The MCA production rate is demonstrated to increase linearly with the uptake rates of glucose and glutamine and with the production rates of lactate and ammonia. The uptake and production rates of these metabolites can, in turn, be predicted from the pumping rates of basal medium to the bioreactor. We recommend a period of 2 weeks at the start of the cultivation when intensive assaying and monitoring should be carried out. After this period, the medium flow rate and MCA production rate may be predicted by linear extrapolation.     

Effect of particle loading on GM-CSF production by Saccharomyces cerevisiae in a three-phase fluidized bed bioreactor

Continuous production of a recombinant murine granulocyte-macrophage colony-stimulating factor (MuGM-CSF) by immobilized yeast cells, Saccharomyces cerevisiae strain XV2181 (a/a, Trp1) containing plasmid palphaADH2, in a fluidized bed bioreactor was studied at a 0.03 h(-1) dilution rate and various particle loading rates ranging from 5% to 33% (v/v). Cells were immobilized on porous glass beads fluidized in an air-lift draft tube bioreactor. A selective medium containing glucose was used to start up the reactor. After reaching a stable cell concentration, the reactor feed was switched to a rich, nonselective medium containing ethanol as the carbon source for GM-CSF production. GM-CSF production increased initially and then dropped gradually to a stable level. During the same period, the fraction of plasmid-carrying cells declined continuously to a lower level, depending on the particle loading. The relatively stable GM-CSF production, despite the large decline in the fraction of plasmid-carrying cells, was attributed to cell immobilization. As the particle loading rate increased, the plasmid stability also increased. Also, as the particle loading increased from 5% to 33%, total cell density in the bioreactor increased from 16 to 36 g/L, and reactor volumetric productivity increased from 0.36 to 1.31 mg/L.h. However, the specific productivity of plasmid-carrying cells decreased from 0.55 to 0.07 mg/L.g cell. The decreased specific productivity at higher particle loading rates was attributed to reduced growth efficiency caused by nutrient limitations at higher cell densities. Both the reactor productivity and specific cell productivity increased by two- to threefold or higher when the dilution rate was increased from 0.03 to 0.07 h(-1). (c) 1996 John Wiley & Sons, Inc.     

Controlling trisulfide modification in recombinant monoclonal antibody produced in fed-batch cell culture

Molecular heterogeneity was detected in a recombinant monoclonal antibody (IgG1 mAb) due to the presence of a trisulfide linkage generated by the post‐translational insertion of a sulfur atom into disulfide bonds at the heavy–heavy and heavy–light junctions. This molecular heterogeneity had no observable effect on antibody function. Nevertheless, to minimize the heterogeneity of the IgG1 mAb from run‐to‐run, an understanding of the impact of cell culture process conditions on trisulfide versus disulfide linkage formation was desirable. To investigate variables that might impact trisulfide formation, cell culture parameters were varied in bench‐scale bioreactor studies. Trisulfide analysis of the samples from these runs revealed that the trisulfide content in the bond between heavy and light chains varied considerably from <1% to 39%. Optimizing the culture duration and feeding strategy resulted in more consistent trisulfide levels. Cysteine concentration in the feed medium had a direct correlation with the trisulfide level in the product. Systematic studies revealed that cysteine in the feed and the bioreactor media was contributing hydrogen sulfide which reacted with the IgG1 mAb in the supernatant leading to the insertion of sulfur atom and formation of a trisulfide bond. Cysteine feed strategies were developed to control the trisulfide modification in the recombinant monoclonal antibody. Biotechnol. Bioeng. 2012; 109: 2523–2532. © 2012 Wiley Periodicals, Inc.