Galactomyces geotrichum Y25产脂肪酶条件的优化

应用响应面法对Galactomyces geotrichumY25液体发酵产脂肪酶的条件进行了优化。首先采用Plackett-Burman设计对影响产酶因素的效应进行评价,筛选出黄豆粉、玉米浆和发酵时间3个对产酶影响显著的因素。用最陡爬坡路径逼近最大产酶区域后,利用响应面设计对显著因素进行优化,得出黄豆粉、玉米浆最佳质量分数分别为2.51%、2.12%,最佳发酵时间101.95 h。优化后液体发酵液中脂肪酶活力提高到34.65 U/mL,比初始酶活力9.6 U/mL提高了3.61倍。表明响应面法可显著优化Galactomyces geotrichumY25液体发酵产脂肪酶条件。     

响应面法优化Burkholderiasp．SYBCLIP—Y发酵产低温脂肪酶条件的研究

用响应面法对Burkholderiasp．SYBCLIP—Y液体发酵产低温脂肪酶的发酵条件进行了快速优化。首先利用Plackett—Burman设计对影响其产酶相关因素进行评估并筛选出具有显著效应的三个因素：牛肉膏,橄榄油,TritonX-100;用最陡爬坡路径逼近最大产酶区域后,利用响应面中心组合设计对显著因素进行优化,确定出牛肉膏,橄榄油,TritonX-100的最佳浓度分别为：牛肉膏31．8g／L、橄榄油21mL／L、TritonX-10036．55mL／L,优化后脂肪酶的酶活达到61．52U／mL,是优化前的2．62倍。     

响应面法优化洋葱假单胞菌产脂肪酶液体发酵工艺

用响应面法对洋葱假单胞菌G-63液体发酵产脂肪酶条件进行了优化。首先运用单因子试验筛选出麦芽糖和豆粉水解液为最适碳源和氮源。在此基础上,通过Plackett-Burman设计试验,对影响产酶条件的11个相关因子进行评估并筛选出具有显著效应的3个因子:橄榄油、豆饼粉水解液以及初始pH值。在用最陡爬坡实验逼近以上3个因子的最大响应区域后,采用响应面分析法,确定出橄榄油、豆粉水解液的最佳浓度和最佳初始pH值分别为4.337%,1.956%和8.38。优化后液体发酵培养基中脂肪酶活力提高到44.39 U/mL,比初始酶活13.45 U/mL提高了3.3倍。     

白地霉Cryytococcus neoformans脂肪酶产酶条件与纯化

目的:获得白地霉脂肪酶发酵的最优条件。方法:采用摇床培养的方法对各种影响因素进行筛选,结果:最适产酶条件为:豆油作碳源,蛋白胨作氮源,PEG600为表面活性剂,添加MgSO4、FeSO4、ZnSO4,pH8.7培养48h。采用双水相萃取和凝胶过滤两步纯化得到电泳均一的脂肪酶,纯化倍数达到72.2倍,其相对分子量约为38±1kDa。结论:得出采用双水相萃取脂肪酶的方法比较理想,该研究为新疆天山一号冰川白地霉脂肪酶的研究奠定了理论基础。     

白地霉一新变种的鉴定及其脂肪酶的研究

从各种加工厂采集的污泥、废水样品中,分离出157株菌落呈白色,绒毛状或粉状,皮膜型或脂泥型有脂肪酶活力的菌株。经筛选,获得一株产生高活力脂肪酶的菌株——S863,其发     

响应面法优化枯草芽孢杆菌产脂肪酶的合成培养基

对枯草芽孢杆菌(Bacillus subtilis)CICC20034利用合成培养基液体发酵产脂肪酶的条件进行了优化。首先采用单因子实验筛选出最适诱导剂为三丁酸甘油酯,氮源为尿素,碳源为葡萄糖,无机盐为MgSO4。在此基础上,利用Plackett-Burman设计对影响产酶因素的效应进行评价,筛选出具有显著效应的三丁酸甘油酯、尿素、KH2PO4和培养基起始pH值4个最显著的因素。用最陡爬坡路径逼近最大产酶区域后,利用响应面中心组合设计对显著因素进行优化,获得最适合成培养基组分为:葡萄糖8g/L,尿素8.57g/L,三丁酸甘油酯2.62%,KH2PO42.59g/L,MgSO4.7H2O0.5g/L,TritonX-1000.5g/L,pH9.47。优化后的B.subtilis CICC 20034胞外脂肪酶活力达0.483U/ml,比初始酶活力0.072U/ml提高了6.7倍。     

白地霉Y162脂肪酶基因克隆及其在毕赤酵母中的高效表达

借助生物信息学,对已克隆的地霉属脂肪酶全长基因序列进行同源比对,根据保守序列设计引物,在基因组DNA和cDNA水平上,于国内首次克隆了Geotrichum candidum Y162脂肪酶基因.Gcandidum Y162脂肪酶基因全长1692bp,不含内含子,编码包括19个氨基酸信号肽在内的563个氨基酸.与NCBI GenBank中已报道的地霉属脂肪酶氨基酸序列有86%的一致性.将该基因克隆到pPIC9K表达载体上,转化毕赤酵母GS115,摇瓶发酵96h后毕赤酵母分泌表达55 U/mL重组脂肪酶,实现了脂肪酶的高效表达.酶学性质研究表明,该重组脂肪酶对C9位顺式双键的甘油酯具有明显的底物特异性;对甲醇、甘油等有机溶剂呈现耐受性;最适温度和最适pH分别为50℃和8.0,在pH6.0～10.0及60℃以下能保持60%以上的酶活力.底物特异性、有机溶剂、温度及pH耐受性赋予该重组酶良好工业应用潜力.     

白地霉Cryytococcus neoformans脂肪酶的双水相萃取

本文研究了不同无机盐的双水相体系对白地霉脂肪酶的萃取分离效果,对PEG/（NH4）2SO4成相系统进行了系统的研究,通过考察体系PEG分子量、不同的无机盐、PEG浓度、（NH4）2SO4浓度、离子强度、pH值及（NH4）2SO4浓度对反萃取的影响,并通过正交实验进一步优化了实验条件,初步确定在PEG浓度15%,（NH4）2SO4浓度22.5%,pH8.0,不加NaCl的条件下进行双水相萃取,脂肪酶分离系数和纯化倍数分别为6.8和7.5,比活力达到40.3 U/mg蛋白。     

响应面法优化耐有机溶剂脂肪酶营养条件

目的：通过优化蜡状芽孢杆菌SWWL6产耐有机溶剂脂肪酶营养条件,产酶量有较大提高。方法与结果：通过单因素实验确定了产酶的最佳碳源、氮源及无机盐分别为可溶性淀粉、酵母膏、NH4NO3、MgSO4·7H2O和NaCl。部分因子实验结果表明初始培养基中酵母膏、NH4NO3的质量浓度对产酶的影响显著。通过最陡爬坡实验逼近最大响应区域。以中心组合设计和响应面分析法确定了最优培养基。结论：优化的培养基为酵母膏0.64%、NH4NO30.384%、可溶性淀粉1%、MgSO4·7H2O0.1%、NaCl0.25%、甲苯20%。优化后脂肪酶相对酶活为348.44%,比优化前提高了3.48倍。     

Optimization of lipase-catalyzed synthesis of acetylated EGCG by response surface methodology

(−)-Epigallocatechin-3-O-gallate (EGCG) acetylated derivatives, which can be widely used as a natural antioxidant in both lipid containing food and cosmetic applications, were prepared by lipase catalyzed acylation of EGCG with vinyl acetate. Response surface methodology (RSM) and 5-level-4-factor central composite rotatable design (CCRD) were employed to evaluate the effects of synthesis parameters, such as reaction time (6–10 h), temperature (30–50 °C), enzyme amount (1.5–2.5% (w/w) of substrate), and substrate molar ratio of EGCG to vinyl acetate (0.5–1.5) on conversion of EGCG. By using multiple regression analysis, the experimental data were fitted to a second order polynomial model. The most suitable combination of variables was 40 °C, 2.12%, 10 h and 1.13 for the reaction temperature, the enzyme amount, the reaction time, and EGCG/vinyl acetate mole ratio, respectively. At these optimal conditions, the conversion yield reached 87.37%. The presence of mono-, di- and tri-acetylated derivatives in acetylated EGCG was confirmed by LC–MS-MS and identified as 5″-O-acetyl-EGCG, 3″, 5″-2-O-acetyl-EGCG and 5′, 3″, 5″-3-O-acetyl-EGCG by NMR.     

Statistical optimization of medium components and growth conditions by response surface methodology to enhance lipase production by Aspergillus carneus

A response surface approach has been used to study the production of an extracellular lipase from Aspergillus carneus, which has the property of immense industrial importance. Interactions were studied for five different variables (sunflower oil, glucose, peptone, agitation rate and incubation period), which were found influential for lipase production by one-at a time method. We report a 1.8-fold increase in production, with the final yield of 12.7 IU/ml in comparison to 7.2 U/ml obtained by one-at-a-time method. Using the statistical approach (response surface methodology (RSM)) the optimum values of these most influential parameters were as follows: sunflower oil (1%), glucose (0.8%), peptone (0.8%), agitation rate (200 rpm) and incubation period (96 h) at 37 °C. The subsequent verification experiment confirmed the validity of the model.     

Optimization of pancreatic lipase inhibition by Cudrania tricuspidata fruits using response surface methodology

The fruits of Cudrania tricuspidata (Carr.) Bur. (Moraceae) significantly inhibited pancreatic lipase, which plays a key role in fat absorption. Optimization of extraction conditions with minimum pancreatic lipase activity and maximum yield was determined using response surface methodology with three-level-three-factor Box–Behnken design (BBD). Regression analysis showed a good fit of the experimental data and the optimal condition was obtained as ethanol concentration, 74.5%; temperature 61.9 °C and extraction time, 13.5 h. The pancreatic lipase activity and extraction yield under optimal conditions were found to be 65.5% and 54.0%, respectively, which were well matched with the predicted value of 65.8% and 47.1%. Further fractionation of C. tricuspidata extract resulted in the isolation of compound 1, which was identified as 5,7,4′-trihydroxy-6,8-diprenylisoflavone. It inhibited pancreatic lipase activity with IC₅₀ value of 65.0 μM. HPLC analysis suggested positive correlation between pancreatic lipase inhibition and 5,7,4′-trihydroxy-6,8-diprenylisoflavone of C. tricuspidata fruits.     

Optimization of culture conditions for production of cis-epoxysuccinic acid hydrolase using response surface methodology

Response surface methodology, which allows for rapid identification of important factors and optimization of them to enhance enzyme production, was employed here to optimize culture conditions for the production of cis-epoxysuccinic acid hydrolase from Bordetella sp. strain 1–3. In the first step, a Plackett–Burman design was used to evaluate the effects of nine variables (yeast extract, cis-epoxysuccinic acid, KH₂PO₄, K₂HPO₄ · 3H₂O, MgSO₄ · 7H₂O, trace minerals solution, culture volume, initial pH and incubation time) on the enzyme production. Yeast extract, cis-epoxysuccinic acid and KH₂PO₄ had significant influences on cis-epoxysuccinic acid hydrolase production and their concentrations were further optimized using central composite design and response surface analysis. A combination of adjusting the concentration of yeast extract to 7.8 g/l, cis-epoxysuccinic acid to 9.8 g/l, and KH₂PO₄ to 1.12 g/l would favor maximum cis-epoxysuccinic acid hydrolase production. An enhancement of cis-epoxysuccinic acid hydrolase production from 5.6 U/ml to 9.27 U/ml was gained after optimization.     

响应面法优化黑曲霉产异淀粉酶的培养条件

在液态发酵条件下,采用单因素实验确定了Aspergillus niger PZ331产异淀粉酶的最适碳源和氮源,分别为蔗糖和硝酸铵。在上述基础上利用Plackett-Burman设计对影响产异淀粉酶的因素进行评价,并筛选出硝酸铵、接种量、培养温度3个主要因素;继而利用响应面设计优化了最佳硝酸铵浓度、接种量和培养温度。最终确定了最优培养条件为：蔗糖10 g/L,硝酸铵10 g/L,磷酸氢二钾3 g/L,硫酸亚铁0.01 g/L,硫酸镁1 g/L,起始p H值4.2;接种量2%（孢子浓度为107cfu/m L）,30℃培养72 h,酶活达137.3μ/m L;比基础培养基的提高了1.71倍左右。     

Optimization of conditions for acid protease partitioning and purification in aqueous two-phase systems using response surface methodology

Aspergillopepsin I, an acid protease, was purified using an aqueous two-phase system that comprised various combinations of polyethylene glycol (PEG), NaH₂PO₄ and NaCl. Partition of the enzyme depended upon the molecular mass of the PEG and the presence of NaCl. With PEG 1500, 4000 and 6000, the partition coefficients were increased by 1,500-, 1,800- and 560-fold compared to values without NaCl. The presence of NaCl (8.75%, w/w) increased purification by 3.8, 9.5 and 2.8 times into these respective PEGs. The optimal aqueous two-phase system for acid protease purification was developed using response surface methodology. This system contained 17.3% of PEG 4000 (w/w), 15% NaH₂PO₄ (w/w) and 8.75% NaCl (w/w) and provided the best partition coefficient (Ke > 1,100) and yield over 99% in the same phase. The optimal ATPS purification factor of acid protease was over 5.     

Use of response surface methodology to optimize culture medium for production of lipase with Candida sp. 99-125

Response surface methodology (RSM) was employed to optimize culture medium for production of lipase with Candida sp. 99-125. In the first step, a Plackett–Burmen design was used to evaluate the effects of different components in the culture medium. Soybean oil, soybean powder and K₂HPO₄ have significant influences on the lipase production. The concentrations of three factors were optimized subsequently using central composite designs and response surface analysis. The optimized condition allowed the production of lipase to be increased from 5000 to 6230 IU/ml in shake flask system. The lipase fermentation in 5 l fermenter reached 9600 IU/ml.     

Optimization of culture conditions for production of yeast biomass using bamboo wastewater by response surface methodology

Response surface methodology (RSM) was applied to optimize culture conditions for the growth of Candida utilis with bamboo wastewater. A significant influence of initial pH, fermentation time and yeast extract on biomass of C. utilis was evaluated by Plackett–Burman design (PBD). These factors were further optimized using a central composite design (CCD) and RSM. A combination of initial pH 6.1, fermentation time 69 h and yeast extract 1.17 g/L was optimum for maximum biomass of C. utilis. A 1.7-fold enhancement of biomass of C. utilis was gained after optimization in shake-flask cultivation. The biomass of C. utilis reached 19.17 g/L in 3 L fermentor.