Comparison of CSTR and UASB reactor configuration for the treatment of sulfate rich wastewaters under acidifying conditions

The effects of lowering the operational pH from 6 to 5 on mesophilic (30 °C) sulfate reduction during the acidification of sucrose at an organic loading rate of 5 gCOD (l_reactor d)⁻¹ and at a COD/SO₄²⁻ ratio of 4 were evaluated in a CSTR and in a UASB reactor. The HRT was 24 h and 10 h, respectively. Acidification was complete in both reactors at pH 6 and the lowering of the operational pH to 5 did not affect the acidification efficiency in the CSTR but decreased the acidification efficiency of the UASB to 72%. The decrease to pH 5 caused an increase in the effluent butyrate and ethanol concentrations in both reactors. Lowering the pH from 6 to 5 caused a decrease in sulfate reduction efficiencies in both reactors, from 43% to 25% in the CSTR and from 95% to 34% in the UASB reactor. The acidification and sulfate reduction efficiencies at pH 5 could be increased to 94% and 67%, respectively, by increasing the HRT of the UASB reactor to 24 h.     

Anaerobic treatment of low-strength wastewater with a high fraction of particulate matter in an unconventional two-phase ASBRs system

The results of a two-phase anaerobic system using anaerobic sequencing batch reactors (ASBRs), treating low-strength wastewater (COD ∼ 500 mg/L) with a high fraction of particulate organic matter (70%, COD basis), are presented. Two reactors in series were used; the first one was hydrolytic–acidogenic, while the second one was methanogenic. This configuration was proposed to promote high efficiency solids removal. During the experiment, 69% and 50% efficiencies of total COD removal were obtained for OLRs of 0.63 and 1.22 kgCOD/(m³ d), respectively. Values of the solubilized organic fraction (SOF) achieved in the hydrolytic–acidogenic reactor were within the range of 0.3–0.6 gCOD_solubilized/gpCOD_removed, and the average acidified organic fraction (AOF) was 0.6 gCOD_VFA-produced/gsCOD_fed. The methanogenic reactor had a VFA removal fraction (VFARF) between 0.4 and 0.6 gCOD_VFA-removed/gCOD_VFA-fed for the OLR of 0.63 and 1.22. The two-phase ASBR system is suitable, and can be implemented, for the anaerobic treatment of this kind of wastewater.     

Low pH (6, 5 and 4) sulfate reduction during the acidification of sucrose under thermophilic (55 °C) conditions

The effect of a low pH (6, 5 and 4) and different COD/SO₄²⁻ ratios (9 and 3.5) on thermophilic (55 °C) sulfate reduction and acidification of sucrose was investigated using three upflow anaerobic sludge bed reactors fed with sucrose at an organic loading rate of 3.5 gCOD (l_reactor d)⁻¹. The three reactors showed nearly 100% acidification of sucrose for all pH values and COD/SO₄²⁻ ratios investigated. Sulfate reduction was complete at pH 6 and a COD/SO₄²⁻ ratio of 9. At pH 5, sulfate reduction efficiencies were 80–95% for both COD/SO₄²⁻ ratios (9 and 3.5). At pH 4, sulfate reduction efficiencies further dropped to 55–65% at a COD/SO₄²⁻ ratio of 9 and 30–40% at a COD/SO₄²⁻ ratio of 3.5. The pH decrease from 6 to 5 or 4 caused a shift in the acidification products from mainly acetate to butyrate, as well as a higher production of ethanol, especially at pH 4. At pH 4, propionate and methane were not formed and hydrogen concentrations in the biogas reached 50%, equivalent to a hydrogen yield of 1.3 mol H₂ (mol glucose)⁻¹. This study shows that sulfate reduction is possible in the acidification phase of anaerobic wastewater treatment at pH values as low as 6 till 4 and that the pH strongly affects both the acidification pathways and the sulfate reduction efficiencies.     

Anaerobic thermophilic digestion of cutting oil wastewater: Effect of co-substrate

This paper describes the thermophilic (55 °C) anaerobic biodegradation of a mixed feed composed of vinasses and cutting oil wastewater (COW) in a laboratory upflow anaerobic fixed-film reactor (UAFF) with a porous support medium. The experimental protocol was defined to examine the effect of increasing the percentage of cutting oil wastewater in the feed.The UAFF reactor was initially started-up with vinasses as the only carbon source at an organic loading rate of 22.3 kg COD/m³ day and HRT of 0.8 days using porous particles as the support (SIRAN). The percentage of organic matter composed of vinasses was subsequently reduced while increasing the amount of cutting oil until 100% of cutting oil wastewater was added in the feed. Four stages were considered in the study (0, 42.4, 66.6 and 100% COW). HRT was adjusted in order to maintain an approximately constant organic loading rate applied to the system. Under theses conditions, the UAFF reactor was subjected to a programme of steady-state operation with hydraulic retention times (HRT) in the range 0.8–0.15 days and organic loading rates (OLR) between 22.3 and 14.9 kg COD/m³ day in order to evaluate the treatment capacity of the system.The COD removal efficiency was found to be 87% COD and 94.6% TOC in the reactor when treating vinasses at 22.3 kg COD/m³ day. The volumetric methane level produced in the digester reached 0.45 m³/m³ day. After an operating period of 120 days, the reactor was fed with cutting oil wastewater (COW) as the only source of carbon. An OLR of 16.7 kg COD/m³ day was achieved with 85.8% COD removal efficiency (58.1%TOC) in the experimental UAFF reactor. Under these conditions the volumetric methane produced in the digester was negligible.Hence, COW can be removed, if not degraded, by anaerobic treatment in the presence of a biodegradable co-substrate. Wine vinasses degradation creates conditions for non-biological removal of COW constituents. More studies are necessary in order to test the mechanisms of organic removal when biodegradation apparently had ceased. Also, toxicity assays of COW are necessary to evaluate the toxicity to the methanogenic community.     

Anaerobic submerged membrane bioreactor (AnSMBR) treating low-strength wastewater under psychrophilic temperature conditions

An anaerobic submerged membrane bioreactor (AnSMBR) treating low-strength wastewater was operated for 90 days under psychrophilic temperature conditions (20 °C). Besides biogas sparging, additional shear was created by circulating sludge to control membrane fouling. The critical flux concept was used to evaluate the effectiveness of this configuration. Biogas sparging with a gas velocity (U_G) of 62 m/h together with sludge circulation (94 m/h) led to a critical flux of 7 L/(m² h). Nevertheless, a further increase in the U_G only minimally enhanced the critical flux. A low fouling rate was observed under critical flux conditions. The cake layer represented the main fouling resistance after 85 days of operation. Distinctly different volatile fatty acid (VFA) concentrations in the reactor and in the permeate were always observed. This fact suggests that a biologically active part of the cake layer contributes to degrade a part of the daily organic load. Hence, chemical oxygen demand (COD) removal efficiencies of up to 94% were observed. Nevertheless, the biogas balance indicates that even considering the dissolved methane, the methane yield were always lower than the theoretical value, which indicates that the organic compounds were not completely degraded but physically retained by the membrane in the reactor.     

Anaerobic digestion of harvested aquatic weeds: water hyacinth (Eichhornia crassipes), cabomba (Cabomba Caroliniana) and salvinia (Salvinia molesta)

The aim of this study was to explore the potential of three aquatic weeds, water hyacinth, cabomba, and salvinia, as substrates for anaerobic digestion. A set of four pilot-scale, batch digestions were undertaken to assess the yield and quality (% methane) of biogas from each plant species, and the rate of degradation. A set of 56 small-scale (100 mL) biological methane potential (BMP) tests were designed to test the repeatability of the digestions, and the impact of drying and nutrient addition.The results of the pilot-scale digestions show that both water hyacinth and cabomba are readily degradable, yielding 267 L biogas kg^?1 VS and 221 L biogas kg^?1 VS, respectively, with methane content of approximately 50%. There is evidence that the cabomba fed reactor leaked midway through the digestion therefore the biogas yield is potentially higher than measured in this case. Salvinia proved to be less readily degradable with a yield of 155 L biogas kg^?1 VS at a quality of 50% methane.The BMPs showed that the variability was low for water hyacinth and cabomba but high for salvinia. They also showed that the addition of nutrient solution and manure did not significantly increase the biogas yields and that drying was detrimental to the anaerobic degradability of all three substrates.Based on these results treatment of both water hyacinth and cabomba by anaerobic digestion can be recommended. Anaerobic digestion of Salvinia cannot be recommended due to the low biogas yields and high variability for this substrate.     

Hemicellulose sugar recovery from steam-exploded wheat straw for microbial oil production

There are currently few successful examples of using straw hemicellulose as a carbon source in the fermentation industry. In this paper, hemicellulose hydrolysates were recovered from steam-exploded wheat straw (SEWS) and used to produce microbial oil. The effects of the steam explosion treatment conditions, the elution temperature and the ratio of elution water to SEWS on sugar recovery were examined. A broth with 3.8 g l^?1 of reducing sugar and 22.3 g l^?1 of total soluble sugars was obtained with a 10-fold excess (w/w) of water at 40 °C to wash the SEWS treated under steam explosion conditions at 200 °C for 5 min. This broth was used to produce microbial oil by the oleaginous fungus Microsphaeropsis sp., which was able to secrete xylanase to degrade oligosaccharides from straw hemicellulose and accumulate microbial oil. Under optimized conditions, the oil concentration was 2.6 g l^?1. The yield of oil from sugar consumed was 0.14 g g^?1. The microbial oil produced by this research could be used as feedstock for biodiesel production because the microbial oil was primarily composed of neutral lipids. This research establishes a novel protocol for microbial oil production from straw hemicellulose.     

Evaluation of distant carbon sources in biosurfactant production by a gamma ray-induced Pseudomonas putida mutant

Pseudomonas putida 33 wild strain, subjected to gamma ray mutagenesis and designated as P. putida 300-B mutant was used as microbial rhamnolipid-producer by using distant carbon sources (viz. hydrocarbons, waste frying oils ‘WFOs’, vegetable oil refinery wastes and molasses) in the minimal media under shake flask conditions. The behavior of glucose as co-substrate and growth initiator was examined. The 300-B mutant strain showed its ability to grow on all the substrates tested and produced rhamnolipid surfactants to different extents however; soybean and corn WFOs were observed to be preferred carbon sources followed by kerosene and paraffin oils, respectively. The best cell biomass (3.5 g l⁻¹) and rhamnolipids yield (4.1 g l⁻¹) were obtained with soybean WFO as carbon source and glucose as growth initiator under fed-batch cultivation showing an optimum specific growth rate (μ) of 0.272 h⁻¹, specific product yield (q_p) of 0.318 g g⁻¹ h and volumetric productivity (P_V) of 0.024 g l⁻¹ h. The critical micelle concentration of its culture supernatant was observed to be 91 mg rhamnolipids l⁻¹ and surface tension as 31.2 mN m⁻¹.     

Phenol and sulfide oxidation in a denitrifying biofilm reactor and its microbial community analysis

A microbial consortium attached onto a polyethylene support was used to evaluate the simultaneous oxidation of sulfide and phenol by denitrification. The phenol, sulfide and nitrate loading rates applied to an inverse fluidized bed reactor were up to 168 mg phenol–C/(l d), 37 mg S^2?/(l d) and 168 mg NO₃^?–N/(l d), respectively. Under steady state operation the consumption efficiencies of phenol, sulfide and nitrate were 100%. The N₂ yield (g N₂/g NO₃^?–N) was 0.89. The phenol was mineralized resulting in a yield of 0.82 g bicarbonate–C/g phenol–C and sulfide was completely oxidized to sulfate with a yield of 0.99 g SO₄^2?–S/g S^2?. 16S rRNA gene-based microbial community analysis of the denitrifying biofilm showed the presence of Thauera aromatica, Thiobacillus denitrificans, Thiobacillus sajanensis and Thiobacillus sp. This is the first work reporting the simultaneous oxidation of sulfide and phenol in a denitrifying biofilm reactor.     

Functional consortium for hydrogen production from cellobiose: Concentration-to-extinction approach

A functional bacterial consortium that can effectively hydrolyze cellobiose and produce bio-hydrogen was isolated by a concentration-to-extinction approach. The sludge from a cattle feedlot manure composting plant was incubated with 2.5–20 g l^?1 cellobiose at 35 °C and pH 6.0. The microbial diversity of serially concentrated suspensions significantly decreased following increasing cellobiose concentration, finally leaving only two viable strains, Clostridium butyricum strain W4 and Enterococcus saccharolyticus strain. This consortium has a maximum specific hydrogen production rate of 2.19 mol H₂ mol hexose^?1 at 5 g l^?1 cellobiose. The metabolic pathways shifted from ethanol-type to acetate-butyrate type as cellobiose concentration increased from 2.5 to >7 g l^?1. The concentration-to-extinction approach is effective for isolating functional consortium from natural microflora. In this case the functional strains of interest are more tolerant to the increased loadings of substrates than the non-functional strains.     

Continuous biomethanization of agrifood industry waste: A case study in Spain

The anaerobic digestion technology is a biological treatment widely used to reduce the pollution load of wet waste biomass. In this work we present the results obtained by performing extensive experiments of anaerobic digestion of slaughterhouse waste, tomato industry waste and olive oil industry waste in continuous mode, which were designed to demonstrate that anaerobic digestion is an effective technology from an environmental and economic point of view.Biogas yields obtained are between 35.22 and 5.45 Nm³ biogas/m³ olive oil industry waste and tomato industry waste respectively and the slaughterhouse wastes achieve intermediate production, 30.86 Nm³ biogas/m³ municipal slaughterhouse waste and 22.53 Nm³ biogas/m³ Iberian pig slaughterhouse waste. Moreover, it possible to degrade between 63.46 and 75.3% of the initial organic matter.If these results are analyzed, the environmental, energetic economic benefits of anaerobic digestion can be quantified. Biomethanation of all these wastes generated annually in Extremadura could prevent the emission of 134,772 t of equivalent carbon dioxide, generate an energy similar to that provided by 2826 toe and reach payback times from 3.29 to 3.75 years for anaerobic digestion plant designed to treat the wastes generated by a medium-sized industry. So, we have fulfilled all the planned aims.     

Microbial processes and bacterial populations associated to anaerobic treatment of sulfate-rich wastewater

A pilot-scale (1.2 m³) anaerobic sequencing batch biofilm reactor (ASBBR) containing mineral coal for biomass attachment was fed with sulfate-rich wastewater at increasing sulfate concentrations. Ethanol was used as the main organic source. Tested COD/sulfate ratios were of 1.8 and 1.5 for sulfate loading rates of 0.65–1.90 kgSO₄²⁻/cycle (48 h-cycle) or of 1.0 in the trial with 3.0 gSO₄²⁻ l⁻¹. Sulfate removal efficiencies observed in all trials were as high as 99%. Molecular inventories indicated a shift on the microbial composition and a decrease on species diversity with the increase of sulfate concentration. Beta-proteobacteria species affiliated with Aminomonas spp. and Thermanaerovibrio spp. predominated at 1.0 gSO₄²⁻ l⁻¹. At higher sulfate concentrations the predominant bacterial group was Delta-proteobacteria mainly Desulfovibrio spp. and Desulfomicrobium spp. at 2.0 gSO₄²⁻ l⁻¹, whereas Desulfurella spp. and Coprothermobacter spp. predominated at 3.0 gSO₄²⁻ l⁻¹. These organisms have been commonly associated with sulfate reduction producing acetate, sulfide and sulfur. Methanogenic archaea (Methanosaeta spp.) was found at 1.0 and 2.0 gSO₄²⁻ l⁻¹. Additionally, a simplified mathematical model was used to infer on metabolic pathways of the biomass involved in sulfate reduction.     

Mathematical analysis of trickling filter response to pentachlorophenol shock load

The response of a laboratory trickling filter to a step increase in pentachlorophenol (PCP) feed concentration was analyzed using continuous stirred tank (CSTR) and plug flow reactor (PFR) models. The CSTR model provided a slightly better fit to experimental data than the plug flow model when specific growth rate, μ, and PCP-degrading biomass concentration before the shock load, X₀, were variable parameters but was clearly superior when the mean residence time, τ, was added as a third parameter. The three-parameter CSTR model accurately represented six of seven concentration response curves corresponding to step increases in PCP feed concentration of 12–165 mg l⁻¹ and 20–150 mg l⁻¹. The continuing improvement in system response to repetitive 20–150 mg l⁻¹ shock loads was reflected by a monotonic increase in the optimal estimates of initial rate of biomass production.     

An integrated anaerobic–aerobic bioreactor (IAAB) for the treatment of palm oil mill effluent (POME): Start-up and steady state performance

Palm oil mill effluent (POME) with average chemical oxygen demand (COD) and biochemical oxygen demand (BOD) of 70,000 and 30,000 mg/L, respectively, can cause serious environmental hazards if discharged untreated. There are conventional palm oil mill effluent (POME) treatment systems that require large footprint, long HRT and fail to meet the Malaysian Department of Environment (DOE) discharge limit. Hence, the current research is aimed to design a novel integrated anaerobic–aerobic bioreactor (IAAB) for POME treatment in order to overcome these shortcomings of the conventional system. IAAB is a new bioreactor configuration which integrates anaerobic and aerobic digestion in one reactor. The overall removal efficiencies in steady state condition in terms of chemical oxygen demand (COD), biochemical oxygen demand (BOD) and total suspended solids (TSS) were more than 99% at the organic loading rate (OLR) of 10.5 g COD/L day with methane yield of 0.24 L CH₄/g COD removed. The effluent quality remained stable (BOD < 70 mg/L) and complied with the discharge limit (BOD < 100 mg/L). Overall, the IAAB system exhibited good stability and pH adjustment was unnecessary. The results show that the IAAB achieves higher performance in terms of organic removal efficiency and methane yield at higher OLR and shorter HRT as compared to the conventional system. Further evaluations of its long-term performance are proposed for the subsequent study.     

Thermophilic treatment of bulk drug pharmaceutical industrial wastewaters by using hybrid up flow anaerobic sludge blanket reactor

The hybrid up flow anaerobic sludge blanket reactor was evaluated for efficacy in reduction of chemical oxygen demand (COD) and biochemical oxygen demand (BOD) of bulk drug pharmaceutical wastewater under different operational conditions. The start-up of the reactor feed came entirely with glucose, applied at an organic loading rate (OLR) 1 kg COD/m³ d. Then the reactor was studied at different OLRs ranging from 2 to 11 kg COD/m³ d with pharmaceutical wastewater. The optimum OLR was found to be 9 kg COD/m³ d, where we found 65–75% COD and 80–94% of BOD reduction with biogas production containing 60–70% of methane and specific methanogenic activity was 320 ml CH₄/g-VSS d. By the characterization studies of effluent using GC–MS, the hazardous compounds like phenol, l,2-methoxy phenol, 2,4,6-trichloro phenol, dibutyl phthalate, 1-bromo naphthalene, carbamazepine and antipyrine were present. After the treatment, these compounds degraded almost completely except carbamazepine. Thermophilic methanothrix and methanosaetae like bacteria are present in the granular sludge.     

Iodine concentration of milk in a dose–response study with dairy cows and implications for consumer iodine intake

Most feed is poor in iodine and iodine supplementation of cow's diets must guarantee milk iodine concentrations for humans that contribute to prevention of the deficiency and minimize the risk of exceeding an upper limit of iodine intake. Five Holstein cows were fed four iodine doses (via Ca(ΙO₃)₂·6H₂O). In four sequential 14-d periods, doses of 0.2 (basal diet), 1.3, 5.1, and 10.1 mg iodine kg^?1 diet dry matter (DM) were administered. Samples of milk were collected during each period; blood was also sampled from each cow for each iodine dosage. In an 18-d depletion period, a non-supplemented diet was provided. Iodine was determined by inductively coupled plasma-mass spectrometry. The iodine content of milk and serum reflected the iodine dosages in feed significantly. The levels for the four doses tested in milk were 101±32, 343±109, 1215±222, and 2762±852 μg iodine kg^?1. The total amount of iodine in milk per day was 30–40% of ingested supplemental iodine. Omitting additional iodine resulted in a short-term reduction of serum and milk iodine following an exponential decay function. The iodine supplementation of 0.5–1.5 mg kg^?1 diet DM represents the requirement of the cow, resulting in 100–300 μg iodine L^?1 milk, which optimally contributes to human supply. The maximum dietary levels of former and present EU legislations (10 and 5 mg iodine kg^?1 cow feed) increase the risk of iodine excess in humans.     

Potentials of anaerobic treatment for catalytically oxidized olive mill wastewater (OMW)

The catalytically oxidized olive mill wastewater (OMW) was subjected to continuous anaerobic treatment using two treatment schemes. The 1st step in both schemes was an up-flow anaerobic sludge blanket (UASB) reactor (2 0 l). The 2nd step was either a hybrid UASB reactor or a classical one (1 0 l, each). The 1st stage was operated at constant hydraulic retention time (HRT) of 24 h. The organic loading rate (OLR) varied from 3.4 to 4.8 kgCOD/m³ d depending on the quality of the pretreated wastewater. The results obtained indicated that, the 1st step UASB reactor achieved a COD percentage removal value of 53.9%. Corresponding total BOD₅ and TSS removal were 51.5% and 68.3%, respectively.The results obtained indicated that the hybrid UASB reactor as a 2nd step produced better quality effluent as compared to the classical one. This could be attributed to the presence of the packing curtain sponge with active biomass in the sedimentation part of hybrid UASB reactor which minimizes suspended solids washout, consequently enhancement of the efficiency of the reactor.Available data showed that a two stage system consisting of a classical and a hybrid UASB reactor operated at a total HRT of 48 h and OLR of 2.0 kgCOD/m³ d provided promising results. Removal values of COD_total, BOD_5 total, TOC, VFA, oil and grease were 83%, 84%, 81%, 93% and 81%, respectively. Based on the available data, the use of a two stage anaerobic system consisting of a classical UASB reactor followed by a hybrid UASB as a post-treatment step for catalytically oxidized OMW is recommended.     

Application of polyethylene glycol immobilized Clostridium sp. LS2 for continuous hydrogen production from palm oil mill effluent in upflow anaerobic sludge blanket reactor

A novel polyethylene glycol (PEG) gel was fabricated and used as a carrier to immobilize Clostridium sp. LS2 for continuous hydrogen production in an upflow anaerobic sludge blanket (UASB) reactor. Palm oil mill effluent (POME) was used as the substrate carbon source. The optimal amount of PEG-immobilized cells for anaerobic hydrogen production was 12% (w/v) in the UASB reactor. The UASB reactor containing immobilized cells was operated at varying hydraulic retention times (HRT) that ranged from 24 to 6 h at 3.3 g chemical oxygen demand (COD)/L/h organic loading rate (OLR), or at OLRs that ranged from 1.6 to 6.6 at 12 h HRT. The best volumetric hydrogen production rate of 336 mL H₂/L/h (or 15.0 mmol/L/h) with a hydrogen yield of 0.35 L H₂/g COD_removed was obtained at a HRT of 12 h and an OLR of 5.0 g COD/L/h. The average hydrogen content of biogas and COD reduction were 52% and 62%, respectively. The major soluble metabolites during hydrogen fermentation were butyric acid followed by acetic acid. It is concluded that the PEG-immobilized cell system developed in this work has great potential for continuous hydrogen production from real wastewater (POME) using the UASB reactor.     

Effects of nitrobenzene concentration and hydraulic retention time on the treatment of nitrobenzene in sequential anaerobic baffled reactor (ABR)/continuously stirred tank reactor (CSTR) system

The effects of increasing nitrobenzene (NB) concentrations and hydraulic retention times (HRT) on the treatment of NB were investigated in a sequential anaerobic baffled reactor (ABR)/aerobic completely stirred tank reactor (CSTR) system. In the first step of the study, the maximum COD removal efficiencies were found as 88% and 92% at NB concentrations varying between 30 mg L^?1 and 210 mg L^?1 in ABR. The minimum COD removal efficiency was 79% at a NB concentration of 700 mg L^?1. The removal efficiency of NB was nearly 100% for all NB concentrations in the ABR reactor. The methane gas production and the methane gas percentage remained stable (1500 mL day^?1 and 48–50%, respectively) as the NB concentration was increased from 30 to 210 mg L^?1. In the second step of the study it was found that as the HRT decreased from 10.38 days to 2.5 days the COD removal efficiencies decreased slightly from 94% to 92% in the ABR. For maximum COD and NB removal efficiencies the optimum HRT was found as 2.5 days in the ABR. The total COD removal efficiency was 95% in sequential anaerobic (ABR)/aerobic (CSTR) reactor system at a minimum HRT of 1 day. When the HRT was decreased from 10.38 days to 1 day, the methane percentage decreased from 42% to 29% in an ABR reactor treating 100 mg L^?1 NB. Nitrobenzene was reduced to aniline under anaerobic conditions while aniline was mineralized to catechol with meta cleavage under aerobic conditions.     

NOB suppression and adaptation strategies in the partial nitrification–Anammox process for a poultry manure anaerobic digester

Poultry manure contains high levels of ammonia, which result in a suboptimal bioconversion to methane in anaerobic digesters (AD). A simultaneous process of nitrification, Anammox and denitrification (SNAD) in a continuous granular bubble column reactor to treat the anaerobically digested poultry manure was implemented. Thus, two strategies to achieve high efficiencies were proposed in this study: (1) ammonia overload to suppress nitrite oxidizing bacteria (NOB) and (2) gradual adaptation of the partial nitrification–Anammox (PN–A) biomass to organic matter. During the NOB-suppression stage, microbial and physical biomass characterizations were performed and the NOB abundance decreased from 31.3% to 3.3%. During the adaptation stage, with a nitrogen loading rate of 0.34 g L⁻¹ d⁻¹, a hydraulic retention time of 1.24 d and an influent COD/N ratio of 2.63 ± 0.02, a maximum ammonia and total nitrogen removal of 100% and 91.68% were achieved, respectively. The relative abundances of the aerobic and the anaerobic ammonia-oxidizing bacteria were greater than 35% and 40% respectively, during the study. These strategies provided useful design tools for the efficient removal of nitrogen species in the presence of organic matter.