Detection of Bacillus anthracis spores and a model protein using PEMC sensors in a flow cell at 1 mL/min

Piezoelectric-excited millimeter-sized cantilever (PEMC) sensors of 4mm(2) sensing area were immobilized with antibody specific to Bacillus anthracis (anti-BA) spores or bovine serum albumin (anti-BSA). Detection of pathogen (Bacillus anthracis (BA) at 300 spores/mL) and BSA (1 mg/mL) were investigated under both stagnant and flow conditions. Two flow cell designs were evaluated by characterizing flow-induced resonant frequency shifts. One of the flow cells labeled SFC-2 (hold-up volume of 0.3 mL), showed small fluctuations (+/-20 Hz) around a common resonant frequency response of 217 Hz in the flow rate range of 1-17 mL/min. The total resonant frequency change obtained for the binding of 300 spores/mL in 1h was 90+/-5 Hz (n=2), and 162+/-10 Hz (n=2) under stagnant and flow conditions, respectively. Binding of antibodies, anti-BA and anti-BSA, were more rapid under flow than under stagnant conditions. The sensor was repeatedly exposed to BSA with an intermediate release step. The first and second responses to BSA were nearly identical. The total resonant frequency response to BSA was 388+/-10 (n=2) Hz under flow conditions. Kinetic analysis is carried out to quantify the effect of flow rate on antibody immobilization and the two types of detection experiments.     

PEMC sensor's mass change sensitivity is 20 pg/Hz under liquid immersion

To enhance the mass change sensitivity of the resonating piezoelectric-excited millimeter-sized cantilever (PEMC) sensors, we reduced its length and eliminated one layer of its composite structure. As a result the mass sensitivity of the second flexural mode increased by two orders of magnitude (from 10(-9) to 10(-11)g/Hz) and the resonant frequency increased by more than 5 kHz. We demonstrate the effects of modification by detecting a model pathogen Group A Streptococcus (GAS) at 700 cells/mL. The resonant frequency change of the second mode at concentrations of 700, 7 x 10(3), 7 x 10(5), 7 x 10(6), 7 x 10(7), and 7 x 10(9)cells/mL resulted in, respectively, 3.1+/-0.5, 11.6+/-1, 15.7+/-1, 25.7+/-0.15, 28.5+/-2, and 40.5+/-3 ng (n=3 for all) of pathogen attachment. A kinetic model for the binding is proposed and verified. The observed binding rate constant was found to be in the range of 0.051-0.166 min(-1). The significance of the results we report is that the modified PEMC sensors have high mass sensitivity that pathogens can be detected at very low concentration under liquid immersion conditions.     

Detect of Escherichia coli O157:H7 in ground beef samples using piezoelectric excited millimeter-sized cantilever (PEMC) sensors

Piezoelectric-excited millimeter-sized cantilever (PEMC) sensors consisting of a piezoelectric and a borosilicate glass layer with a sensing area of 4 mm2 were fabricated. An antibody specific to Escherichia coli (anti-E. coli) O157:H7 was immobilized on PEMC sensors, and exposed to samples containing E. coli O157:H7 (EC) prepared in various matrices: (1) broth, broth plus raw ground beef, and broth plus sterile ground beef without inoculation of E. coli O157:H7 served as controls, (2) 100 mL of broth inoculated with 25 EC cells, (3) 100 mL of broth containing 25 g of raw ground beef and (4) 100 mL of broth with 25 g of sterile ground beef inoculated with 25 EC cells. The total resonant frequency change obtained for the broth plus EC samples were 16+/-2 Hz (n=2), 30 Hz (n=1), and 54+/-2 Hz (n=2) corresponding to 2, 4, and 6h growth at 37 degrees C, respectively. The response to the broth plus 25 g of sterile ground beef plus EC cells were 21+/-2 Hz (n=2), 37 Hz (n=1), and 70+/-2 Hz (n=2) corresponding to 2, 4, and 6 h, respectively. In all cases, the three different control samples yielded a frequency change of 0+/-2 Hz (n=6). The E. coli O157:H7 concentration in each broth and beef samples was determined by both plating and by pathogen modeling program. The results indicate that the PEMC sensor detects E. coli O157:H7 reliably at 50-100 cells/mL with a 3 mL sample.     

The effect of salt and phage concentrations on the binding sensitivity of magnetoelastic biosensors for Bacillus anthracis detection

This article presents an investigation of the effect of salt and phage concentrations on the binding affinity of magnetoelastic (ME) biosensors. The sensors were fabricated by immobilizing filamentous phage on the ME platform surface for the detection of Bacillus anthracis spores. In response to the binding of spores to the phage on the ME biosensor, a corresponding decrease occurs in resonance frequency. Transmission electron microscopy (TEM) was used to verify the structure of phage under different combinations of salt/phage concentration. The chemistry of the phage solution alters phage bundling characteristics and, hence, influences both the sensitivity and detection limit of the ME biosensors. The frequency responses of the sensors were measured to determine the effects of salt concentration on the sensors' performance. Scanning electron microscopy (SEM) was used to confirm and quantify the binding of spores to the sensor surface. This showed that 420 mM salt at a phage concentration of 1 x 10(11) vir/mL results in an optimal distribution of immobilized phages on the sensor surface, consequently promoting better binding of spores to the biosensor's surface. Additionally, the sensors immobilized with phage under this condition were exposed to B. anthracis spores in different concentrations ranging from 5 x 10(1) to 5 x 10(8) cfu/mL in a flowing system. The results showed that the sensitivity of this ME biosensor was 202 Hz/decade.     

Near real-time detection of Cryptosporidium parvum oocyst by IgM-functionalized piezoelectric-excited millimeter-sized cantilever biosensor

Piezoelectric-excited millimeter-sized cantilever (PEMC) biosensors were fabricated and functionalized with immunoglobulin M (IgM) for the detection of Cryptosporidium parvum oocyst in a flow configuration at 1 mL/min. The detection of 100, 1000, and 10,000 oocysts/mL was achieved with a positive sensor response in less than 1 min. Bovine serum albumin (BSA) was used as a blocking agent in each experiment and was shown to eliminate non-specific binding. The sensor's resonance frequency response correlates with C. parvum oocyst concentration logarithmically. The oocyst attachment rate was found to increase by an order of magnitude in increasing concentration from 100 to 10,000 oocysts/mL. The significance of these results is that IgM-functionalized PEMC sensors are highly selective and sensitive to C. parvum oocyst and therefore, have the potential to accurately identify and quantify C. parvum oocyst in drinking water.     

A procedure for high-yield spore production by Bacillus subtilis

Bacillus subtilis spores have a number of potential applications, which include their use as probiotics and competitive exclusion agents to control zoonotic pathogens in animal production. The effect of cultivation conditions on Bacillus subtilis growth and sporulation was investigated in batch bioreactions performed at a 2-L scale. Studies of the cultivation conditions (pH, dissolved oxygen concentration, and media composition) led to an increase of the maximum concentration of vegetative cell from 2.6 x 10(9) to 2.2 x 10(10) cells mL(-)(1) and the spore concentration from 4.2 x 10(8) to 5.6 x 10(9) spores mL(-)(1). A fed-batch bioprocess was developed with the addition of a nutrient feeding solution using an exponential feeding profile obtained from the mass balance equations. Using the developed feeding profile, starting at the middle of the exponential growth phase and finishing in the late exponential phase, an increase of the maximum vegetative cell concentration and spore concentration up to 3.6 x 10(10) cells mL(-)(1) and 7.4 x 10(9) spores mL(-)(1), respectively, was obtained. Using the developed fed-batch bioreaction a 14-fold increase in the concentration of the vegetative cells was achieved. Moreover, the efficiency of sporulation under fed-batch bioreaction was 21%, which permitted a 19-fold increase in the final spore concentration, to a final value of 7.4 x 10(9) spores mL(-)(1). This represents a 3-fold increase relative to the highest reported value for Bacillus subtilis spore production.     

Formaldehyde gas inactivation of Bacillus anthracis, Bacillus subtilis, and Geobacillus stearothermophilus spores on indoor surface materials

AIMS: To evaluate the decontamination of Bacillus anthracis, Bacillus subtilis, and Geobacillus stearothermophilus spores on indoor surface materials using formaldehyde gas. METHODS AND RESULTS: B. anthracis, B. subtilis, and G. stearothermophilus spores were dried on seven types of indoor surfaces and exposed to approx. 1100 ppm formaldehyde gas for 10 h. Formaldehyde exposure significantly decreased viable B. anthracis, B. subtilis, and G. stearothermophilus spores on all test materials. Significant differences were observed when comparing the reduction in viable spores of B. anthracis with B. subtilis (galvanized metal and painted wallboard paper) and G. stearothermophilus (industrial carpet and painted wallboard paper). Formaldehyde gas inactivated>or=50% of the biological indicators and spore strips (approx. 1x10(6) CFU) when analyzed after 1 and 7 days. CONCLUSIONS: Formaldehyde gas significantly reduced the number of viable spores on both porous and nonporous materials in which the two surrogates exhibited similar log reductions to that of B. anthracis on most test materials. SIGNIFICANCE AND IMPACT OF THE STUDY: These results provide new comparative information for the decontamination of B. anthracis spores with surrogates on indoor surfaces using formaldehyde gas.     

Detection and quantification of proteins using self-excited PZT-glass millimeter-sized cantilever

A composite self-excited PZT-glass cantilever (4mm in length and 2mm wide) was fabricated and used to measure the binding and unbinding of model proteins. A key feature of the cantilever is that its resonant frequency is dependent on its mass. The fabricated cantilever has mass change sensitivity in liquid of 7.2 x 10(-11)g/Hz. Resonant frequency change was measured as protein reacted or bound with the sensing glass cantilever surface. Protein concentrations, 0.1 and 1.0mg/mL, which resulted in nanogram mass change were successfully detected. The mass change sensitivity gave a total mass change of 54+/-0.45 ng for the binding of anti-rabbit IgG (biotin conjugated) to rabbit IgG immobilized cantilever and the subsequent binding of captavidin. The unbinding of anti-rabbit IgG and captavidin gave a total mass change of 54+/-1.70 ng. Fluorescence based assays showed the combined mass of both proteins in the released samples was 54+/-2.24 ng. The binding kinetics of the model proteins is modeled as first order. The initial binding rate constant of anti-rabbit IgG to rabbit IgG was 1.36+/-0.02(min(mg/mL))(-1). The initial binding rate constant of captavidin to biotinylated anti-rabbit IgG was (2.57 x 10(-1))+/-0.003(min(mg/mL))(-1). The significance of the results we report here is that millimeter-sized PZT-actuated glass cantilevers have the sensitivity to measure in real-time protein-protein binding, and the binding rate constant.     

Microresonator mass sensors for detection of Bacillus anthracis Sterne spores in air and water

Towards the goal of developing a real-time monitoring device for microorganisms, we demonstrate the use of microcantilevers as resonant mass sensors for detection of Bacillus anthracis Sterne spores in air and liquid. The detection scheme was based on measuring resonant frequency decrease driven by thermally induced oscillations, as a result of the added mass of the spores with the use of a laser Doppler vibrometer (LDV). Viscous effects were investigated by comparing measurements in air and deionized (DI) water along with theoretical values. Moreover, biological experiments were performed which involved suspending spores onto the cantilevers and performing mass detection in air and water. For detection of spores in water, the cantilevers were functionalized with antibodies in order to fix the spores onto the surface. We demonstrate that as few as 50 spores on the cantilever can be detected in water using the thermal noise as excitation source. Measurement sensitivity of 9.23 Hz/fg for air and 0.1 Hz/fg for water were obtained. These measurements were compared with theoretical values and sources of improvement in cantilever sensitivity in a viscous medium were also discussed. It is expected that by driving the cantilevers and using higher order modes, detection of a single spore in liquids should be achievable.     

In vitro selection of DNA aptamers to anthrax spores with electrochemiluminescence detection.

Systematic evolution of ligands by exponential enrichment (SELEX) was used to select and PCR amplify DNA sequences (aptamers) capable of binding to and detecting nonpathogenic Sterne strain Bacillus anthracis spores. A simplified affinity separation approach was employed, in which autoclaved anthrax spores were used as the separation matrix. An aptamer-magnetic bead-electrochemiluminescence (AM-ECL) sandwich assay scheme was devised for detecting anthrax spores. Using a low SELEX DNA to spore ratio (154 ng DNA/10(6) spores), at least three distinct populations of single-stranded DNA aptamers, having varied affinities for anthrax spores, were noted by the AM-ECL assay. Results reflect detection of spore components with a dynamic range equivalent to < 10- > 6 x 10(6) anthrax spores. In the low DNA to spore ratio experiments, aptamers could be liberated from spore pellets by heating at 96 degrees C for 5 min after each round of SELEX. When a much higher DNA to spore ratio (10,256 ng DNA/10(6) spores) was used for SELEX development, a higher affinity set of aptamers was selected that could not be heat-eluted even at 99 degrees C for 5 min following round four of SELEX. However, high affinity spore surface bound aptamers were detectable via their 5'-biotinylated tails using labeled avidin and could be eluted in deionized water. Aptamers have potential for use as inexpensive, in vitro-generated receptors for biosensors in biological warfare detection and other areas.     

Decontamination assessment of Bacillus anthracis, Bacillus subtilis, and Geobacillus stearothermophilus spores on indoor surfaces using a hydrogen peroxide gas generator

AIMS: To evaluate the decontamination of Bacillus anthracis, Bacillus subtilis, and Geobacillus stearothermophilus spores on indoor surface materials using hydrogen peroxide gas. METHODS AND RESULTS: Bacillus anthracis, B. subtilis, and G. stearothermophilus spores were dried on seven types of indoor surfaces and exposed to > or =1000 ppm hydrogen peroxide gas for 20 min. Hydrogen peroxide exposure significantly decreased viable B. anthracis, B. subtilis, and G. stearothermophilus spores on all test materials except G. stearothermophilus on industrial carpet. Significant differences were observed when comparing the reduction in viable spores of B. anthracis with both surrogates. The effectiveness of gaseous hydrogen peroxide on the growth of biological indicators and spore strips was evaluated in parallel as a qualitative assessment of decontamination. At 1 and 7 days postexposure, decontaminated biological indicators and spore strips exhibited no growth, while the nondecontaminated samples displayed growth. CONCLUSIONS: Significant differences in decontamination efficacy of hydrogen peroxide gas on porous and nonporous surfaces were observed when comparing the mean log reduction in B. anthracis spores with B. subtilis and G. stearothermophilus spores. SIGNIFICANCE AND IMPACT OF THE STUDY: These results provide comparative information for the decontamination of B. anthracis spores with surrogates on indoor surfaces using hydrogen peroxide gas.     

Sensitive and selective detection of mycoplasma in cell culture samples using cantilever sensors

In this article we report a new biosensor‐based method that is more sensitive and rapid than the current approach for detecting mycoplasma in cell culture samples. Piezoelectric‐excited millimeter‐sized cantilever (PEMC) sensors respond to mass change via resonant frequency change. They are sensitive at femtogram level and can be used directly in liquid for label‐free detection. Common cell culture contaminant, Acholeplasma laidlawii was detected in both buffer and cell culture medium. Two different sources (positive control from a commercial kit and ATCC 23206) were analyzed using antibody‐immobilized PEMC sensor. Resonant frequency decrease caused by binding of A. laidlawii was monitored in real‐time using an impedance analyzer. Positive detection was confirmed by a second antibody binding. The limit of detection (LOD) was lower than 10³ CFU/mL in cell culture medium using PEMC sensor while parallel ELISA assays showed LOD as 10⁷ CFU/mL. This study shows that PEMC sensor can be used for sensitive and rapid mycoplasma detection in cell culture samples. Biotechnol. Bioeng. 2010;105: 1069–1077. © 2009 Wiley Periodicals, Inc.     

Construction, crystal structure and application of a recombinant protein that lacks the collagen-like region of BclA from Bacillus anthracis spores

Spores of Bacillus anthracis, the causative agent of anthrax, are enclosed by an exosporium, which consists of a basal layer surrounded by a nap of hair-like filaments. The major structural component of the filaments is called BclA, which comprises a central collagen-like region (CLR) and a globular C-terminal domain. Here, the entire CLR coding sequence of BclA was removed, and the resulting protein (tBclA) produced in Escherichia coli. The crystallographic structure of tBclA was determined to 1.35 A resolution, and consists of an all-beta structure with a TNF-like jelly fold topology (12 beta-strands which form 2 beta-sheets of five strands each) consistent with previous studies on wild-type BclA. These globular domains are tightly packed into trimeric structures (surface shape complementarity; S (c) = 0.83), demonstrating that formation of the core structure of BclA is independent of the anchoring collagen-like region. A polyclonal antibody raised against tBclA recognized B. anthracis spores directly, and showed little cross-reactivity (<10%) with the spores of the closely related species Bacillus cereus and Bacillus thuringiensis, when compared to two other polyclonal antibodies raised against B. anthracis spore extracts and inactivated spores. The tBclA protein was used to purify a pool of specific antibodies from bovine colostrum whey samples from cows inoculated with the Sterne strain anthrax vaccine, which also showed reactivity with B. anthracis spores. Together, these results demonstrate that tBclA provides a safer and more effective way to the production and purification of antibodies with high binding affinity for B. anthracis spores. Biotechnol. Bioeng. 2008;99: 774-782. (c) 2007 Wiley Periodicals, Inc.     

Sensitive and rapid quantitative detection of anthrax spores isolated from soil samples by real-time PCR

Quantitative analysis of anthrax spores from environmental samples is essential for accurate detection and risk assessment since Bacillus anthracis spores have been shown to be one of the most effective biological weapons. Using TaqMan real-time PCR, specific primers and probes were designed for the identification of pathogenic B. anthracis strains from pag gene and cap gene on two plasmids, pXO1 and pXO2, as well as a sap gene encoded on the S-layer. To select the appropriate lysis method of anthrax spore from environmental samples, several heat treatments and germination methods were evaluated with multiplex-PCR. Among them, heat treatment of samples suspended with sucrose plus non-ionic detergent was considered an effective spore disruption method because it detected up to 10(5) spores/g soil by multiplex-PCR. Serial dilutions of B. anthracis DNA and spore were detected up to a level of 0.1 ng/ microliters and 10 spores/ml, respectively, at the correlation coefficient of 0.99 by real-time PCR. Quantitative analysis of anthrax spore could be obtained from the comparison between C(T) value and serial dilutions of soil sample at the correlation coefficient of 0.99. Additionally, spores added to soil samples were detected up to 10(4) spores/g soil within 3 hr by real-time PCR. As a consequence, we established a rapid and accurate detection system for environmental anthrax spores using real-time PCR, avoiding time and labor-consuming preparation steps such as enrichment culturing and DNA preparation.     

Six new species of microsporidia of the genus Amblyospora (Microspora: Amblyosporidae) from blood sucking mosquitoes (Diptera: Culicidae) from the west Siberia

Microsporidia of the genus Amblyospora parasiting the adipose body of mosquito larvae of the genus Aedes and Culex has been studied with both light and electron microscopy. Six new species of microsporidia are described based on ultrastructural characteristics of spores and sporogony stages. Amblyospora flavescens sp. n. Mature spores are egg-shaped. The spore wall with three layers, about 165 nm. Exospore is two-membranous. Subexospore is absent. Endospore is electron-translucent. Polaroplast consists of three parts: lamellar, large vesicular, lamellar. The anisofilar polar filament with 10--11 coils (3 1/2 + 2 1/2 + 4-5). Fixed spores are 6.3 +/- 0.1 x 4.24 +/- 0.1 microm. Amblyospora kolarovi sp. n. Mature spores are egg-shaped. The spore wall with three layers, about 265-315 nm. Exospore shapes tucks on the surface of spore. It is two-membranous. Subexospore is quagge, structural. Endospore is electron-translucent. Polaroplast consists of two parts: lamellar and large vesicular. The anisofilar polar filament with 11-13 coils (3 + 8-10). Fixed spores are 5.4-5.6 x 3.5-4.2 microm. Amblyospora orbiculata sp. n. Mature spores are widely egg-shaped. On a back pole there is a small concavity. The spore wall with three layers, about 155 nm. Exospore is shapes tucks on a surface of spore. It is two-membranous. Subexospore is absent. Endospore is electron-translucent. Polaroplast consists of three parts: lamellar, vesicular, lamellar. Polar filament is anisofilar, with 11 1/2 coils (4 1/2 + 1 + 6). Fixed spores are 6.3 +/- 0.1 x x 4.0 +/- 0.1 microm. Amblyospora rugosa sp. n. Mature spores are egg-shaped. On a back pole there is a small concavity. The spore wall with three layers, about 225 nm. Exospore is shapes tucks on a surface of spore. It is two-membranous. Subexospore is quaggy, structural. Endospore is electron-translucent. Polaroplast lamellate. Polar filament is anisofilar, with 17 1/2 coils (3 1/2 + 1 + 13). Fixed spores are 5.3 +/- 0.1 x 3.7 +/- 0.1 microm. Amblyospora undata sp. n. Mature spores are egg-shaped. The spore wall is three-layered, about 220 nm. Exospore is shapes tucks on a surface of spore. It is two-membranous. Subexospore is quaggy, structural. Endospore is electron-translucent. Polaroplast lamellate. The anisofilar polar filament with 8 coils (3 + 5). Fixed spores are 5.0 +/- 0.1 x 3.0 +/- 0.1 microm. Amblyospora urski sp. n. Mature spores have widely oval form. The back pole is concave. The spore wall with three layers, about 280 nm. Exospore is shapes tucks on a surface of spore. It is two-membranous. Subexospore is quaggy, structural. Endospore is electron-translucent. Polaroplast lamellate. Polar filament is anisofilar, with 6 coils (2 + 4). Fixed spores are 4.4 +/- 0.1 x 2.9 +/- 0.1 microm.     

Monoclonal antibodies against spore antigens of Bacillus anthracis

Abstract A murine monoclonal antibody produced against heat inactivated spores of Bacillus anthracis Ames, reacted with live or inactivated spores of several anthrax strains in indirect immunofluorescence (IF) tests. The reactive anthrax strain gave only a moderate degree of reaction. No staining of anthrax vegetative cells was observed. The monoclonal did not react with spores of non-anthrax Bacillus strains that gave cross reactions with mouse hyperimmune antiserum raised against Ames spores. The staining of individual spores in B. anthracis preparations was more heterogeneous with the monoclonal antibody than with the hyperimmune serum. Evidence is produced that the epitope for this monoclonal is not stable during long-term storage of inactivated spore preparations, and is not fully available for reaction with antibody until late in spore maturation. The monoclonal did not react by immunoblotting (Western blotting) of spore extracts.     

Detection of spores of Bacillus anthracis from environment using polymerase chain reaction

A sensitive PCR based detection of Bacillus anthracis spores from environnment was standardized. Specific 1247bp amplicon could be detected with template concentration as low as 13 pg. Sensitivity was enhanced to 10 fold by nesting with second set of primers, forming 208bp amplicon. Extraction of DNA from spores purified from soil samples by aqueous polymer two-phase system followed by partial germination and freeze-thaw treatment yielded best results. Soil sample spiked with spores (8x10(2)/g of sample) could be detected with this method.     

Monoclonal antibodies against spore antigens of Bacillus anthracis

A murine monoclonal antibody produced against heat inactivated spores of Bacillus anthracis Ames, reacted with live or inactivated spores of several anthrax strains in indirect immunofluorescence (IF) tests. The reactive anthrax strain gave only a moderate degree of reaction. No staining of anthrax vegetative cells was observed. The monoclonal did not react with spores of non-anthrax Bacillus strains that gave cross reactions with mouse hyperimmune antiserum raised against Ames spores. The staining of individual spores in B. anthracis preparations was more heterogeneous with the monoclonal antibody than with the hyperimmune serum. Evidence is produced that the epitope for this monoclonal is not stable during long-term storage of inactivated spore preparations, and is not fully available for reaction with antibody until late in spore maturation. The monoclonal did not react by immunoblotting (Western blotting) of spore extracts. A monoclonal antibody produced against Ames spore extracts reacted with about 1% of Ames spores in IF tests, but not reproducible reactions with other anthrax strains were recorded. This monoclonal interacted with three bands in Western blots of anthrax spore extracts.     

Anthrax toxin receptor 2 mediates Bacillus anthracis killing of macrophages following spore challenge

Initiation of inhalation anthrax is believed to involve phagocytosis of Bacillus anthracis spores by alveolar macrophages, followed by spore germination within the phagolysosome. In order to establish a systemic infection, it is predicted that bacilli then escape from the macrophage and replicate extracellularly. Mechanisms utilized by B. anthracis to escape from the macrophage are not well characterized, but a role for anthrax toxin has been proposed. Here we report the isolation of an anthrax toxin-resistant cell line (R3D) following chemical mutagenesis of toxin-sensitive RAW 264.7 murine macrophage cells. Both R3D and RAW 264.7 cells phagocytize spores of a B. anthracis Sterne strain. However, RAW 264.7 cells are killed following spore challenge, whereas R3D cells survive. Resistance to toxin and spore challenge correlates with loss of expression of anthrax toxin receptor 2 (ANTXR2/CMG-2). When R3D cells are complemented with cDNA encoding either murine ANTXR2 or human anthrax toxin receptor 1 (ANTXR1/TEM-8), toxin and spore challenge susceptibility are restored, indicating that over-expression of either ANTXR can confer susceptibility to anthrax spore challenge. Taken together, these results indicate that anthrax toxin expression by the germinated spore enables B. anthracis killing of the macrophage from within.     

Virulent spores of Bacillus anthracis and other Bacillus species deposited on solid surfaces have similar sensitivity to chemical decontaminants

AIMS: To compare the relative sensitivity of Bacillus anthracis and spores of other Bacillus spp. deposited on different solid surfaces to inactivation by liquid chemical disinfecting agents. METHODS AND RESULTS: We prepared under similar conditions spores from five different virulent and three attenuated strains of B. anthracis, as well as spores of Bacillus subtilis, Bacillus atrophaeus (previously known as Bacillus globigii), Bacillus cereus, Bacillus thuringiensis and Bacillus megaterium. As spore-surface interactions may bias inactivation experiments, we evaluated the relative binding of different spores to carrier materials. The survival of spores deposited on glass, metallic or polymeric surfaces were quantitatively measured by ASTM standard method E-2414-05 which recovers spores from surfaces by increasing stringency. The number of spores inactivated by each decontaminant was similar and generally within 1 log among the 12 different Bacillus strains tested. This similarity among Bacillus strains and species was observed through a range of sporicidal efficacy on spores deposited on painted metal, polymeric rubber or glass. CONCLUSIONS: The data obtained indicate that the sensitivity of common simulants (B. atrophaeus and B. subtilis), as well as spores of B. cereus, B. thuringiensis, and B. megaterium, to inactivation by products that contain either: peroxide, chlorine or oxidants is similar to that shown by spores from all eight B. anthracis strains studied. SIGNIFICANCE AND IMPACT OF THE STUDY: The comparative results of the present study suggest that decontamination and sterilization data obtained with simulants can be safely extrapolated to virulent spores of B. anthracis. Thus, valid conclusions on sporicidal efficacy could be drawn from safer and less costly experiments employing non-pathogenic spore simulants.