In vivo biomechanical behavior of the human heel pad during the stance phase of gait

A technique is introduced for simultaneous measurements of the heel pad tissue deformation and the heel–ground contact stresses developing during the stance phase of gait. Subjects walked upon a gait platform integrating the contact pressure display optical method for plantar pressure measurements and a digital radiographic fluoroscopy system for skeletal and soft tissue motion recording. Clear images of the posterior-plantar aspect of the calcaneus and enveloping soft tissues were obtained simultaneously with the pressure distribution under the heel region throughout the stance phase of gait. The heel pad was shown to undergo a rapid compression during initial contact and heel strike, reaching a strain of 0.39±0.05 in about 150 ms. The stress–strain relation of the heel pad was shown to be highly non-linear, with a compression modulus of 105±11 kPa initially and 306±16 kPa at 30% strain. The energy dissipation during heel strike was evaluated to be 17.8±0.8%. The present technique is useful for biomechanical as well as clinical evaluation of the stress–strain and energy absorption characteristics of the heel pad in vivo, during natural gait.     

The compressive material properties of the plantar soft tissue

The plantar soft tissue is the primary means of physical interaction between a person and the ground during locomotion. Dynamic loads greater than body weight are borne across the entire plantar surface during each step. However, most testing of these tissues has concentrated on the structural properties of the heel pad. The purpose of this study was to determine the material properties of the plantar soft tissue from six locations beneath: the great toe (subhallucal), the 1st, 3rd and 5th metatarsal heads (submetatarsal), the lateral midfoot (lateral submidfoot) and the heel (subcalcaneal). We obtained specimens from these locations from 11 young, non-diabetic donors; the tissue was cut into 2 cm x 2 cm blocks and the skin was removed. Stress relaxation experiments were conducted and the data were fit using the quasi-linear viscoelastic (QLV) theory. To determine tissue modulus, energy loss and the effect of test frequency, we also conducted displacement controlled triangle waves at five frequencies ranging from 0.005 to 10 Hz. The subcalcaneal tissue was found to have an increased relaxation time compared to the other areas. The subcalcaneal tissue was also found to have an increased modulus and decreased energy loss compared to the other areas. Across all areas, the modulus and energy loss increased for the 1 and 10 Hz tests compared to the other testing frequencies. This study is the first to generate material properties for all areas of the plantar soft tissue, demonstrating that the subcalcaneal tissue is different than the other plantar soft tissue areas. These data will have implications for foot computational modeling efforts and potentially for orthotic pressure reduction devices.     

An inverse finite-element model of heel-pad indentation

A numerical-experimental approach has been developed to characterize heel-pad deformation at the material level. Left and right heels of 20 diabetic subjects and 20 nondiabetic subjects matched for age, gender and body mass index were indented using force-controlled ultrasound. Initial tissue thickness and deformation were measured using M-mode ultrasound; indentation forces were recorded simultaneously. An inverse finite-element analysis of the indentation protocol using axisymmetric models adjusted to reflect individual heel thickness was used to extract nonlinear material properties describing the hyperelastic behavior of each heel. Student's t-tests revealed that heel pads of diabetic subjects were not significantly different in initial thickness nor were they stiffer than those from nondiabetic subjects. Another heel-pad model with anatomically realistic surface representations of the calcaneus and soft tissue was developed to estimate peak pressure prediction errors when average rather than individualized material properties were used. Root-mean-square errors of up to 7% were calculated, indicating the importance of subject-specific modeling of the nonlinear elastic behavior of the heel pad. Indentation systems combined with the presented numerical approach can provide this information for further analysis of patient-specific foot pathologies and therapeutic footwear designs.     

Deformation and stress distribution of the human foot after plantar ligaments release: A cadaveric study and finite element analysis

The majority of foot deformities are related to arch collapse or instability, especially the longitudinal arch. Although the relationship between the plantar fascia and arch height has been previously investigated, the stress distribution remains unclear. The aim of this study was to explore the role of the plantar ligaments in foot arch biomechanics. We constructed a geometrical detailed three-dimensional (3-D) finite element (FE) model of the human foot and ankle from computer tomography images. The model comprised the majority of joints in the foot as well as bone segments, major ligaments, and plantar soft tissue. Release of the plantar fascia and other ligaments was simulated to evaluate the corresponding biomechanical effects on load distribution of the bony and ligamentous structures. These intrinsic ligaments of the foot arch were sectioned to simulate different pathologic situations of injury to the plantar ligaments, and to explore bone segment displacement and stress distribution. The validity of the 3-D FE model was verified by comparing results with experimentally measured data via the displacement and von Mise stress of each bone segment. Plantar fascia release decreased arch height, but did not cause total collapse of the foot arch. The longitudinal foot arch was lost when all the four major plantar ligaments were sectioned simultaneously. Plantar fascia release was compromised by increased strain applied to the plantar ligaments and intensified stress in the midfoot and metatarsal bones. Load redistribution among the centralized metatarsal bones and focal stress relief at the calcaneal insertion were predicted. The 3-D FE model indicated that plantar fascia release may provide relief of focal stress and associated heel pain. However, these operative procedures may pose a risk to arch stability and clinically may produce dorsolateral midfoot pain. The initial strategy for treating plantar fasciitis should be non-operative.     

Differences in foot contact times between obese and non-obese postmenopausal women when crossing obstacles

Abstract

Objective: This study aimed to investigate the foot contact time differences between obese and non-obese subjects during walking when crossing obstacles.

Methods: Ninety-eight postmenopausal women were assigned to four groups, and their plantar pressure temporal data were collected using a two-step protocol during walking when crossing an obstacle set at 30% height of lower limb length of each subject. The initial, final, and duration of contact of 10?foot areas were measured.

Results: Leading limb: (1) the heel groups initiated foot contact using the heel, and the non-heel groups initiated contact using the metatarsals; (2) heel obese subjects showed an earlier initial contact and a longer contact duration of metatarsals 2–3; (3) non-heel obese subjects showed an earlier midfoot initial contact. Regarding the trailing limb: (4) heel obese subjects showed an earlier midfoot initial contact and a longer contact duration of metatarsal 5; (5) non-heel obese subjects showed an earlier initial contact and a longer contact duration of metatarsals 4–5.

Conclusions: (1) The non-heel groups’ foot rollover pattern may result from an attempt of rapidly restoring stability; (2) the heel obese subjects seem to regulate their plantar foot muscles to overcome their overweight; (3) the overweight of the non-heel obese subjects leads to a quicker backward foot roll-over from the metatarsals to the heel; (4) the overweight of the heel obese subjects can distort their footprints and/or their higher inertia may precipitate an anticipation of the midfoot contact, which can also explain the result observed for 5.     

Three-dimensional finite element analysis of the foot during standing--a material sensitivity study

Information on the internal stresses/strains in the human foot and the pressure distribution at the plantar support interface under loading is useful in enhancing knowledge on the biomechanics of the ankle-foot complex. While techniques for plantar pressure measurements are well established, direct measurement of the internal stresses/strains is difficult. A three-dimensional (3D) finite element model of the human foot and ankle was developed using the actual geometry of the foot skeleton and soft tissues, which were obtained from 3D reconstruction of MR images. Except the phalanges that were fused, the interaction among the metatarsals, cuneiforms, cuboid, navicular, talus, calcaneus, tibia and fibula were defined as contact surfaces, which allow relative articulating movement. The plantar fascia and 72 major ligaments were simulated using tension-only truss elements by connecting the corresponding attachment points on the bone surfaces. The bony and ligamentous structures were embedded in a volume of soft tissues. The encapsulated soft tissue was defined as hyperelastic, while the bony and ligamentous structures were assumed to be linearly elastic. The effects of soft tissue stiffening on the stress distribution of the plantar surface and bony structures during balanced standing were investigated. Increases of soft tissue stiffness from 2 and up to 5 times the normal values were used to approximate the pathologically stiffened tissue behaviour with increasing stages of diabetic neuropathy. The results showed that a five-fold increase in soft tissue stiffness led to about 35% and 33% increase in the peak plantar pressure at the forefoot and rearfoot regions, respectively. This corresponded to about 47% decrease in the total contact area between the plantar foot and the horizontal support surface. Peak bone stress was found at the third metatarsal in all calculated cases with a minimal increase of about 7% with soft tissue stiffening.     

A simple field method to identify foot strike pattern during running

Identifying foot strike patterns in running is an important issue for sport clinicians, coaches and footwear industrials. Current methods allow the monitoring of either many steps in laboratory conditions or only a few steps in the field. Because measuring running biomechanics during actual practice is critical, our purpose is to validate a method aiming at identifying foot strike patterns during continuous field measurements. Based on heel and metatarsal accelerations, this method requires two uniaxial accelerometers. The time between heel and metatarsal acceleration peaks (THM) was compared to the foot strike angle in the sagittal plane (α_foot) obtained by 2D video analysis for various conditions of speed, slope, footwear, foot strike and state of fatigue. Acceleration and kinematic measurements were performed at 1000 Hz and 120 Hz, respectively, during 2-min treadmill running bouts. Significant correlations were observed between THM and α_foot for 14 out of 15 conditions. The overall correlation coefficient was r=0.916 (P<0.0001, n=288). The THM method is thus highly reliable for a wide range of speeds and slopes, and for all types of foot strike except for extreme forefoot strike during which the heel rarely or never strikes the ground, and for different footwears and states of fatigue. We proposed a classification based on THM: FFS<−5.49 ms<MFS<15.2 ms<RFS. With only a few precautions being necessary to ensure appropriate use of this method, it is reliable for distinguishing rearfoot and non-rearfoot strikers in situ.     

Effect of heel height on in-shoe localized triaxial stresses

Abnormal and excessive plantar pressure and shear are potential risk factors for high-heeled related foot problems, such as forefoot pain, hallux valgus deformity and calluses. Plantar shear stresses could be of particular importance with an inclined supporting surface of high-heeled shoe. This study aimed to investigate the contact pressures and shear stresses simultaneously between plantar foot and high-heeled shoe over five major weightbearing regions: hallux, heel, first, second and fourth metatarsal heads, using in-shoe triaxial force transducers. During both standing and walking, peak pressure and shear stress shifted from the lateral to the medial forefoot as the heel height increased from 30 to 70mm. Heel height elevation had a greater influence on peak shear than peak pressure. The increase in peak shear was up to 119% during walking, which was about five times that of peak pressure. With increasing heel height, peak posterolateral shear over the hallux at midstance increased, whereas peak pressure at push-off decreased. The increased posterolateral shear could be a contributing factor to hallux deformity. It was found that there were differences in the location and time of occurrence between in-shoe peak pressure and peak shear. In addition, there were significant differences in time of occurrence for the double-peak loading pattern between the resultant horizontal ground reaction force peaks and in-shoe localized peak shears. The abnormal and drastic increase of in-shoe shear stresses might be a critical risk factor for shoe-related foot disorders. In-shoe triaxial stresses should therefore be considered to help in designing proper footwear.     

An MRI-compatible foot-loading device for assessment of internal tissue deformation

It is well known that mechanical forces acting within the soft tissues of the foot can contribute to the formation of neuropathic ulcers in people with diabetes. Presently, only surface measurements of plantar pressure are used clinically to estimate risk status due to mechanical loading. It is currently not known how surface measurements relate to the three-dimensional (3-D) internal stress/strain state of the foot. This article describes the development of a foot-loading device that allows for the direct observation of the internal deformation of foot tissues under known forces. Ground reaction forces and plantar pressure distributions during normal walking were measured in ten healthy young adults. One instant in the gait cycle, when pressure under the metatarsal heads reached a peak, was extracted for simulation in an MR imager. T1-weighted 3-D gradient echo MRI sets were collected as the simulated walking ground reaction force was incrementally applied to the foot by the novel foot-loading device. The sub-metatarsal head soft-tissue thickness decreased rapidly at first and then reached a plateau. Peak plantar pressure measurements collected within the loading device (161+/-75kPa) were lower in magnitude and less focal than pressures measured during walking (492+/-91kPa). This finding implies that although the device successfully applied full peak walking ground reaction forces to the foot, they were not distributed in the same manner as during walking. Although not representative of gait, the data collected from this in vivo mechanical test are suitable for determination of foot tissue material properties or, when combined with finite element modeling, to examine the relationship between surface loading and internal stress.     

The foot as a shock absorber

A mathematical analysis of the deformation of the foot is developed to determine the role that stretch of ligaments and tendons plays in absorbing shock following impact. Our analysis is based on an anatomical biomechanical model that includes each of the bones of the foot. We calculate the time course of the deflection of the joints and the elongation of the ligaments and tendons and determine the ground reaction force acting on the heel. Quasi-linear viscoelastic theory is used for soft tissue constitutive relationships. With biomechanical data selected from the literature, we obtain a vertical force impact peak of 8000 N, occurring at 16 ms following heel strike. This is of higher magnitude and shorter duration than is found experimentally, as is to be expected, since we did not include the heel pad in our model and we assumed that the impact surface was ideally rigid.     

A Phase-Dependent Hypothesis for Locomotor Functions of Human Foot Complex

The human foot is a very complex structure comprising numerous bones, muscles, ligaments and synovial joints. As the only component in contact with the ground, the foot complex delivers a variety of biomechanical functions during human locomotion, e.g. body support and propulsion, stability maintenance and impact absorption. These need the human foot to be rigid and damped to transmit ground reaction forces to the upper body and maintain body stability, and also to be compliant and resilient to moderate risky impacts and save energy. How does the human foot achieve these apparent conflicting functions？ In this study, we propose a phase-dependent hypothesis for the overall locomotor functions of the human foot complex based on in-vivo measurements of human natural gait and simulation results of a mathematical foot model. We propse that foot functions are highly dependent on gait phase, which is a major characteristics of human locomotion. In early stance just after heel strike, the foot mainly works as a shock absorber by moderating high impacts using the viscouselastic heel pad in both vertical and horizontal directions. In mid-stance phase （-80% of stance phase）, the foot complex can be considered as a springy rocker, reserving external mechanical work using the foot arch whilst moving ground contact point forward along a curved path to maintain body stability. In late stance after heel off, the foot complex mainly serves as a force modulator like a gear box, modulating effective mechanical advantages of ankle plantiflexor muscles using metatarsal-phalangeal joints. A sound under- standing of how diverse functions are implemented in a simple foot segment during human locomotion might be useful to gain insight into the overall foot locomotor functions and hence to facilitate clinical diagnosis, rehabilitation product design and humanoid robot development.     

Comparative plethysmography; evidence for a hydrostatic effect on foot blood flow

Blood flow in the right foot of 11 subjects was measured simultaneously by a strain gauge placed around the mid metatarsal circumference of the foot and a water displacement plethysmograph in which the foot was resting. A close linear correlation (r = 0.88) between the results of the two methods existed over a wide range of blood flows. It was apparent however that blood flow at the mid metatarsal region of the foot was only about 30% of the total foot blood flow measured by the plethysmograph. The likely cause of this finding is the varying proportion of bone to soft tissue along the length of the foot. It was observed that the strain gauge estimates of blood flow increased two to three fold when the plethysmograph was emptied, an effect that was abolished by refilling the plethysmograph. These changes were highly statistically significant (P less than 0.01) in all ten subjects in whom this comparison was made. The application of progressively increasing hydrostatic pressure in a further 4 subjects demonstrated that the reduction in blood flow was proportional to the pressure applied. Explanations for this effect based upon small temperature and pressure changes altering strain gauge performance are excluded. Three mechanisms are proposed, based upon an increase in venous leakage, a reduction in arterial inflow and the consequence of increased capillary filling occurring as a result of hydrostatic pressure within the plethysmograph.     

A Coupling Analysis of the Biomechanical Functions of Human Foot Complex during Locomotion

This study represents a functional analysis of the human foot complex based on in-vivo gait measurements, finite element (FE) modeling and biological coupling theory, with the objective of achieving a comprehensive understanding of the impact attenuation and energy absorption functions of the human foot complex. A simplified heel pad FE model comprising reticular fiber structure and fat cells was constructed based on the foot pad Magnetic Resonance (MR) images. The model was then used to investigate the foot pad behaviors under impact during locomotion. Three-dimensional (3D) gait measurement and a 3D FE foot model comprising 29 bones, 85 ligaments and the plantar soft tissues were used to investigate the foot arch and plantar fascia deformations in mid-stance phase. The heel pad simulation results show that the pad model with fat cells (coupling model) has much stronger capacity in impact attenuation and energy storage than the model without fat cells (structure model). Furthermore, the FE simulation reproduced the deformations of the foot arch structure and the plantar fascia extension observed in the gait measurements, which reinforces the postulation that the foot arch structure also plays an important role in energy absorption during locomotion. Finally, the coupling mechanism of the human foot functions in impact attenuation and energy absorption was proposed.     

Dynamic plantar pressure distribution during terrestrial locomotion of bonobos (Pan paniscus)

We collected high-resolution plantar pressure distributions of seven bonobos during terrestrial bipedal and quadrupedal locomotion (N = 146). Functional foot length, degree of hallux abduction, and total contact time were determined, and plots, showing pressure as a function of time for six different foot regions, were generated. We also studied five adult humans for comparison (N = 13). Both locomotion types of the bonobo show a large variation in plantar pressure distributions, which could be due to the interference of instantaneous behavior with locomotion and differences in walking speed and body dimensions. The heel and the lateral midfoot typically touch down simultaneously at initial ground contact in bipedal and quadrupedal walking of bonobos, in contrast with the typical heel-strike of human bipedalism. The center of pressure follows a curved course during quadrupedalism, as a consequence of the medial weight transfer during mid-stance. Bipedal locomotion of bonobos is characterized by a more plantar positioning of the feet and by a shorter contact time than during quadrupedal walking, according to a smaller stride and step length at a higher frequency. We observed a varus position of the foot with an abducted hallux, which likely possesses an important sustaining and stabilizing function during terrestrial locomotion.     

Peak dynamic force in human gait

Studies were made of the forces generated at heel stroke in human gait using both force plates having a high resonant frequencies (capable of picking up high frequency components in the contact force) as well as a force transducer inserted into the heel of the shoe of the subjects. The output traces were analyzed for the existence of high frequency impulsive loads during a normal walking cycle. The effect of the complicance of the foot and floor was studied with the force transducers. The results showed that during normal human gait the lower limb is subjected to a high frequency impulsive load at heel strike. The severity of this impulse varied with the individual, the velocity and angle with which the limb aproached the ground and the compliance of the two materials coming in contact at heel strike. The magnitude of this peak force varied from 0.5 to 1.25 times body weight and its frequency components from 10 to 75 Hz.     

Structural and functional predictors of regional peak pressures under the foot during walking

The objective of this study was to identify structural and functional factors which are predictors of peak pressure underneath the human foot during walking. Peak plantar pressure during walking and eight data sets of structural and functional measures were collected on 55 asymptomatic subjects between 20 and 70 yr. A best subset regression approach was used to establish models which predicted peak regional pressure under the foot. Potential predictor variables were chosen from physical characteristics, anthropometric data, passive range of motion (PROM), measurements from standardized weight bearing foot radiographs, mechanical properties of the plantar soft tissue, stride parameters, foot motion in 3D, and EMG during walking. Peak pressure values under the rearfoot, midfoot, MTH1, and hallux were measured. Heel pressure was a function of linear kinematics, longitudinal arch structure, thickness of plantar soft tissue, and age. Midfoot pressure prediction was dominated by arch structure, while MTH1 pressure was a function of radiographic measurements, talo-crural joint motion, and gastrocnemius activity. Hallux pressure was a function of structural measures and MTP1 joint motion. Foot structure and function predicted only approximately 50% of the variance in peak pressure, although the relative contributions in different anatomical regions varied dramatically. Structure was dominant in predicting peak pressure under the midfoot and MTH1, while both structure and function were important at the heel and hallux. The predictive models developed in this study give insight into potential etiological factors associated with elevated plantar pressure. They also provide direction for future studies designed to reduce elevated pressure in "at-risk" patients.     

In-shoe plantar tri-axial stress profiles during maximum-effort cutting maneuvers

Soft tissue injuries, such as anterior cruciate ligament rupture, ankle sprain and foot skin problems, frequently occur during cutting maneuvers. These injuries are often regarded as associated with abnormal joint torque and interfacial friction caused by excessive external and in-shoe shear forces. This study simultaneously investigated the dynamic in-shoe localized plantar pressure and shear stress during lateral shuffling and 45° sidestep cutting maneuvers. Tri-axial force transducers were affixed at the first and second metatarsal heads, lateral forefoot, and heel regions in the midsole of a basketball shoe. Seventeen basketball players executed both cutting maneuvers with maximum efforts. Lateral shuffling cutting had a larger mediolateral braking force than 45° sidestep cutting. This large braking force was concentrated at the first metatarsal head, as indicated by its maximum medial shear stress (312.2±157.0 kPa). During propulsion phase, peak shear stress occurred at the second metatarsal head (271.3±124.3 kPa). Compared with lateral shuffling cutting, 45° sidestep cutting produced larger peak propulsion shear stress (463.0±272.6 kPa) but smaller peak braking shear stress (184.8±181.7 kPa), of which both were found at the first metatarsal head. During both cutting maneuvers, maximum medial and posterior shear stress occurred at the first metatarsal head, whereas maximum pressure occurred at the second metatarsal head. The first and second metatarsal heads sustained relatively high pressure and shear stress and were expected to be susceptible to plantar tissue discomfort or injury. Due to different stress distribution, distinct pressure and shear cushioning mechanisms in basketball footwear might be considered over different foot regions.     

Explicit finite element modelling of heel pad mechanics in running: inclusion of body dynamics and application of physiological impact loads

Many heel pathologies including plantar heel pain may result from micro tears/trauma in the subcutaneous tissues, in which internal tissue deformation/stresses within the heel pad play an important role. Previously, many finite element models have been proposed to evaluate stresses inside the heel pad, but the majority of these models only focus on static loading boundary conditions. This study explored a dynamics modelling approach to the heel pad subjected to realistic impact loads during running. In this model, the inertial property and action of the body are described by a lumped parameter model, while the heel/shoe interactions are modelled using a viscoelastic heel pad model with contact properties. The impact force pattern, dynamic heel pad deformation and stress states predicted by the model were compared with published experimental data. Further parametrical studies revealed the model responses, in terms of internal stresses in the skin and fatty tissue, change nonlinearly when body dynamics changes. A reduction in foot's touchdown velocity resulted in a less severe impact landing and stress relief inside the heel pad, for example peak von-Mises stress in fatty tissue, was reduced by 11.3%. Applications of the model may be extendable to perform iterative analyses to further understand the complex relationships between body dynamics and stress distributions in the soft tissue of heel pad during running. This may open new opportunities to study the mechanical aetiology of plantar heel pain in runners.     

Response of able-bodied persons to changes in shoe rocker radius during walking: Changes in ankle kinematics to maintain a consistent roll-over shape

Recent studies have determined a seemingly consistent feature of able-bodied level ground walking, termed the roll-over shape, which is the effective rocker (cam) shape that the lower limb system conforms to between heel contact and contralateral heel contact during walking (first half of the gait cycle). The roll-over shape has been found to be largely unaffected by changes in walking speed, load carriage, and shoe heel height. However, it is unclear from previous studies whether persons are controlling their lower limb systems to maintain a consistent roll-over shape or whether this finding is a byproduct of their attempt to keep ankle kinematic patterns similar during the first half of the gait cycle. We measured the ankle–foot roll-over shapes and ankle kinematics of eleven able-bodied subjects while walking on rocker shoes of different radii. We hypothesized that the ankle flexion patterns during single support would change to maintain a similar roll-over shape. We also hypothesized that with decrease in rocker shoe radii, the difference in ankle flexion between the end and beginning of single support would decrease. Our results supported these hypotheses. Ankle kinematics were changed significantly during walking with the different rocker shoe radii (p<0.001), while ankle–foot roll-over shape radii (p=0.146) and fore–aft position (p=0.132) were not significantly affected. The results of this study have direct implications for designers of ankle–foot prostheses, orthoses, walking casts/boots, and rocker shoes. The results may also be relevant to researchers studying control of human movements.     

Suitability of the scapular flap for reconstructions of the foot

Eighteen patients with mainly a traumatic soft-tissue defect of the foot underwent reconstruction with a microvascular free scapular flap. Of the 17 successful transfers, 13 were to the weight-bearing parts of the foot. The stability and contour of the flaps were assessed after an average follow-up time of 3 years (range 1 to 5 years). The thicknesses of the scapular donor site and flap and the recipient site were measured by an ultrasound technique. The resistance of the flap to shear was measured with a dynamometer. The ultrasound measurements aided in refining our operative technique. In early cases, the flap thickness after transfer could be more than double what it was in the donor area. With proper tightening, the thickness could be reduced, with improvement in contour but no increase in soft-tissue stability or shear resistance of the flap. Without proper tightening, the scapular flap tended to be redundant when transferred to the foot. For good results, the patient should be lean, since the optimal thickness of the scapular donor site was less than 6 mm and the maximum thickness should not exceed 8 to 10 mm. The differences in shear resistance between the flaps were not associated with the soft-tissue stability of the reconstruction. The relative laxity of the flap on the plantar surface was found by several patients to be subjectively unpleasant. Although good contour could be achieved when covering the plantar heel, the tendency of the flap to develop abrasions and superficial breakdowns made it unsatisfactory for covering this area.(ABSTRACT TRUNCATED AT 250 WORDS)