Decolorization of structurally different textile dyes by Aspergillus niger SA1

The fungal strain, Aspergillus niger SA1, isolated from textile wastewater sludge was screened for its decolorization ability for four different textile dyes. It was initially adapted to higher concentration of dyes (10–1,000 mg l⁻¹) on solid culture medium after repeated sub-culturing. Maximum resistant level (mg l⁻¹) sustained by fungal strain against four dyes was in order of; Acid red 151 (850) > Orange II (650) > Drimarene blue K₂RL (550) > Sulfur black (500). The apparent dye removal for dyes was seen largely due to biosorption/bioadsorption into/onto the fungal biomass. Decolorization of Acid red 151, Orange II, Sulfur black and Drimarine blue K₂RL was 68.64 and 66.72, 43.23 and 44.52, 21.74 and 28.18, 39.45 and 9.33% in two different liquid media under static condition, whereas, it was 67.26, 78.08, 45.83 and 13.74% with 1.40, 1.73, 5.16 and 1.87 mg l⁻¹ of biomass production under shaking conditions respectively in 8 days. The residual amount (mg l⁻¹) of the three products (α-naphthol, sulfanilic acid and aniline) kept quite low i.e., ≤2 in case AR 151 and Or II under shaking conditions. Results clearly elucidated the role of Aspergillus niger SA1 in decolorizing/degrading structurally different dyes into basic constituents.     

Decolorization of textile dyes by enzymatic extract and submerged cultures of <Emphasis Type="Italic">Pleurotus sajor-caju</Emphasis>

Pleurotus sajor-caju PS2001 was screened in Petri dish plates to assess the dye-decolorizing ability of industrial textile dyes. P. sajor-caju PS2001 was also cultivated in solid-state fermentation containing sawdust of Pinus sp. and wheat bran to obtain the enzymatic extract, showing laccase and manganese-peroxidase activity, which was used to test the capacity to degrade the textile dyes. Additional tests of decolorization were performed in liquid cultures. Anthraquinone-type textile dyes proved to be substrates for the enzymatic system of P. sajor-caju PS2001. Cultures in Petri dish plates showed that the anthraquinone dye Reactive Blue 220 can act as a redox mediator for the enzymatic reactions involved in the decolorization process, and enables the azo dye degradation. Reactive Blue 220 and Acid Blue 280 were completely decolorized in 30 min and 60 min, respectively, during the tests with precipitated enzymatic extract, while the azo dyes showed resistance to degradation. Additionally, in submerged cultures with dyes, veratryl alcohol oxidases and lignin peroxidase activities were observed. These results suggest that the strain P. sajor-caju PS2001 has great potential for use in the bioremediation technology of recalcitrant pollutant such as textile effluents.     

Textile dye decolorization using cyanobacteria

Cyanobacterial cultures isolated from sites polluted by industrial textile effluents were screened for their ability to decolorize cyclic azo dyes. Gloeocapsa pleurocapsoides and Phormidium ceylanicum decolorized Acid Red 97 and FF Sky Blue dyes by more than 80% after 26 days. Chroococcus minutus was the only culture which decolorized Amido Black 10B (55%). Chlorophyll a synthesis in all cultures was strongly inhibited by the dyes. Visible spectroscopy and TLC confirmed that color removal was due to degradation of the dyes.Revisions requested 10 November 2004/30 November 2004; Revisions received 16 November 2004/ 7 January 2005     

Binding of textile azo dyes byMyrothecium verrucaria

Summary A strain ofMyrothecium verrucaria that showed a high capacity for rapid decolorization of textile dye solutions was isolated from soil. As much as 70%, 86%, and 95% of Orange II, 10B (blue) and RS (red) dyes (color index no. 15510, 20470, 23635), respectively, were adsorbed from solutions of approximately 0.2 g dye per liter in 5 h by approximately 4.5 g dry weight of cells per liter of dye solution. Intact cells showed a higher adsorption capacity than disrupted cells for Orange II and RS but not for 10B. Dye bound to cells was recoverable by extraction with methanol and methanol-treated cells were able to be recycled, albeit with a slightly diminished dye-binding capacity. The Tween detergents were shown to reduce dye adsorption. Dyes strongly bound to the fungal biomass required sonication in dH₂O or in Triton X-100 or extraction with methanol for their removal. These results suggest that hydrophobic/hydrophilic interactions are important in dye binding.     

Biodegradation of textile azo-dyes byPhanerochaete chrysosporium

Of 18 commercially used textile dyes, eight were degraded by the white rot fungus,Phanerochaete chrysosporium, by 40 to 73% based on decrease of colour. Both the lignin-degrading enzyme system ofP. chrysosporium and adsorption to its cell mass were involved in the degradation of the diazo dye, Reactofix Gold Yellow. Degradation was best achieved by adding the dye to the medium and then inoculating with pre-grown mycelium; inoculation with spores resulted mainly in dye adsorption.     

MOLECULARLY IMPRINTED POLYMERS FOR SOME REACTIVE DYES

Depending upon their structure, azo- and anthraquinonic dyes are the two major classes and together represent 90% of all organic colorants. Adsorption of dye molecules onto a sorbent can be an effective, low-cost method of color removal. Most of the techniques used for removal of dyes are of high production cost, and the regeneration also makes them uneconomical. There is much interest in the development of cheaper and effective newer materials for use as adsorbents. Molecular imprinting is a new kind of materials that can be alternative adsorbents. In this study, molecularly imprinted polymers of three textile dyes (Cibacron Orange P-4R, Cibacron Red P-4B, Cibacron Black PSG) were prepared. Methacrylic acid was used as a monomer for red and orange dyes and acrylamide was used for black dye. Methanol:acetonitrile was used as a porogen. The selective recognition ability of the molecularly imprinted polymers was studied by an equilibrium–adsorption batch method. The adsorption data are for Cibacron Black PSG 65% and nonimprinted polymer (NIP) 25%; Cibacron Red P-4B 72% and NIP 18%; and Cibacron Orange P-4R 45% and NIP 10%, respectively. Dye-imprinted polymers were used as a solid-phase extraction material for selective adsorption from wastewater of textile factory.     

Molecularly imprinted polymers for some reactive dyes

Depending upon their structure, azo- and anthraquinonic dyes are the two major classes and together represent 90% of all organic colorants. Adsorption of dye molecules onto a sorbent can be an effective, low-cost method of color removal. Most of the techniques used for removal of dyes are of high production cost, and the regeneration also makes them uneconomical. There is much interest in the development of cheaper and effective newer materials for use as adsorbents. Molecular imprinting is a new kind of materials that can be alternative adsorbents. In this study, molecularly imprinted polymers of three textile dyes (Cibacron Orange P-4R, Cibacron Red P-4B, Cibacron Black PSG) were prepared. Methacrylic acid was used as a monomer for red and orange dyes and acrylamide was used for black dye. Methanol:acetonitrile was used as a porogen. The selective recognition ability of the molecularly imprinted polymers was studied by an equilibrium-adsorption batch method. The adsorption data are for Cibacron Black PSG 65% and nonimprinted polymer (NIP) 25%; Cibacron Red P-4B 72% and NIP 18%; and Cibacron Orange P-4R 45% and NIP 10%, respectively. Dye-imprinted polymers were used as a solid-phase extraction material for selective adsorption from wastewater of textile factory.     

Simple and easy method for the determination of fungal growth and decolourative capacity in solid media

A technique was developed for studying the biodegradative ability of white rot fungi in different solid media. This technique enables the gravimetric determination of fungal growth (increase of biomass) and the spectrometric measurement of fungal decolourization ability (both by the determination of the production of the extracellular enzyme manganese-dependent peroxidase (MnP) and by the rate of decolourization of dyes). Bjerkandera sp., strain BOS55, was grown in different solid media. Its growth rate, decolourization of solophenil blue 2BL (azoic dye), neutral red (eurhodin dye), methyl green and crystal violet (triphenylmethane dyes) and the production of MnP were determined. Application of this technique enabled a spectrometric quantification of enzymatic activity. Assays indicate that greater amounts of MnP were present in agar plate cultures of Bjerkandera sp. than in liquid cultures.     

Microbial decolorization of azo dyes and dye industry effluent by Fomes lividus

The white rot fungus, Fomes lividus, was isolated from the logs of Shorea robusta in the Western Ghats region of Tamil Nadu, India. The fungus was tested for decolorization of azo dyes such as orange G (50 M) congo red (50 M) amido black 10B (25 M) and also for colour removal from dye industry effluents. The results revealed that the fungus could remove only 30.8% of orange G in the synthetic solution, whereas congo red and amido black 10B were removed by 74.0 and 98.9% respectively. A dye industry effluent was treated by the fungus in batch and continuous mode. In batch mode treatment, a maximum decolorization of 84.4% was achieved on day 4, and in continuous mode a maximum decolorization of 37.5% was obtained on day 5. The colour removal by the basidiomycete fungus might be due to adsorption of the dyes to the mycelial surface and metabolic breakdown. These results suggested that the batch mode treatment of Fomes lividus is one of the most efficient ways for colour removal in dye industry effluents.     

The evaluation of pre-grown mycelial pellets in decolorization of textile dyes during repeated batch process

This study was undertaken for the possibility of application of pre-grown pellets for biotechnological treatment of dyes and textile industry waste waters. Mycelial pellets of five different white rot fungi were tested for their dye decolorization activity. The pellets of Funalia trogii, Phanerochaete chrysosporium and Trametes versicolor were determined as the most effective ones. The decolorization ability of viable pellets was compared with the decolorization (adsorption) ability of dead pellets during repeated batch studies. Astrazon Black dye was decolorized effectively, about 90%, by viable pellets of all fungi during the first use. Viable F. trogii pellets were found as the most effective pellets. Upon pellet treatment not only a high decolorization but also reduced toxicity (antimicrobial activity) of the Astrazon Black dye was recorded. This type of decolorization activity with commercial or crude laccase was partially observed. Growing cells of F. trogii in batch system showed lower efficiency in color removal of mixed dyes compared to the pre-grown pellets in repeated batch system. The results in this study showed that mycelial pellets could effectively be used as an alternative to traditional physicochemical processes.     

Decolorization of Victoria blue by the white rot fungus, <Emphasis Type="Italic">Phanerochaete chrysosporium</Emphasis>

Synthetic textile dyes are among the most dangerous chemical pollutants released in industrial wastewater streams. Recognizing the importance of reducing the environmental impact of these dyes, the ability of the white rot fungus Phanerochaete chrysosporium to decolorize various textile dyes was investigated. This fungus decolorized 6 of the 14 structurally diverse dyes with varying efficiency (between 14% and 52%). There was no discernable pattern of decolorization even among dyes of the same chemical class, suggesting that attack on the dyes is relatively non-specific. Among the three dyes which showed >40% decolorization, Victoria Blue B (VB) was chosen for further analysis because the ability of the fungus to decolorize VB was nearly independent over a relatively broad concentration range. Blocking lignin peroxidase (LiP) and manganese peroxidase (MnP) production by the fungus did not substantially affect VB decolorization. Inhibition of laccase production by adding various inhibitors to shaken cultures reduced VB decolorization significantly suggesting a role for laccase in VB decolorization. When sodium azide and aminotriazole were used to inhibit endogenous catalase and cytochrome P-450 oxygenase activities, there was 100% and 70% reduction in VB decolorization, respectively. Adding benzoate to trap hydrogen peroxide-derived hydroxyl radicals resulted in 50% decolorization of VB. Boiling the extracellular fluid (ECF) for 30 min resulted in approximately 50% reduction in VB decolorization. Collectively, these data suggest that laccase, and/or oxygenase/oxidase and a heat-stable non-enzymatic factor, but not Lip and MnP, play a role in VB decolorization by P. chrysosporium.     

Effect of various synthetic dyes on the production of manganese-dependent peroxidase isoenzymes by immobilized <Emphasis Type="Italic">Irpex lacteus</Emphasis>

The effect of manganese and selected synthetic dyes on the production of manganese-dependent peroxidase (MnP) by Irpex lacteus immobilized on polyurethane foam was studied. In the cultures grown in a medium containing 65 μM Mn (II), up to three various isoenzymes of MnP were resolved by isolectrofocusing, with pI values within the range of 3.50–6.04. In the cultures grown in a medium containing 2.9 mM Mn (II), two new MnP isoforms (pI 3.28, 3.75) were produced. The addition of structurally different synthetic dyes, an azo dye Reactive Orange 16 (RO16), an anthraquinonic dye Remazol Brilliant Blue R (RBBR), and a triphenylmethane dye Bromophenol Blue (BPB), to the fungal cultures grown in the presence of high manganese inhibited the production of low pI MnP isoforms. However, in the presence of BPB a new MnP isoform with pI 5.67 was detected. BPB was found to induce MnP isoforms which are more effective in RBBR decolorization in vitro than the low pI isoforms present in the control cultures.     

Production of the Phanerochaete flavido-alba laccase in Aspergillus niger for synthetic dyes decolorization and biotransformation

We investigated the expression of Phanerochaete flavido-alba laccase gene in Aspergillus niger and the physical and biochemical properties of the recombinant enzyme (rLac-LPFA) in order to test it for synthetic dye biotransformation. A. niger was able to produce high levels of active recombinant enzyme (30 mgL^?1), whose identity was further confirmed by immunodetection using Western blot analysis and N-terminal sequencing. Interestingly, rLac-LPFA exhibited an improved stability at pH (2–9) and organic solvents tested. Furthermore, the percentage of decoloration and biotransformation of synthetic textile dyes, Remazol Brilliant Blue R (RBBR) and Acid Red 299 (NY1), was higher than for the native enzyme. Its high production, simple purification, high activity, stability and ability to transform textile dyes make rLac-LPFA a good candidate for industrial applications.     

Decolorization of Acid Black 210 by <Emphasis Type="Italic">Vibrio harveyi</Emphasis> TEMS1, a newly isolated bioluminescent bacterium from Izmir Bay,Turkey

The present study deals with the decolorization of Acid Black 210 by a bioluminescent bacterium, Vibrio harveyi TEMS1, isolated from coastal seawater of Izmir Bay, Turkey. Maximum rate of decolorization of Acid Black 210 was observed when Luria Bertani medium was used. Decolorization of Acid Black 210 was 38.9% and 93.9% at 24 h under shaking and static conditions, respectively. The optimum dye-decolorizing activity of the culture was obtained at 100 ppm initial dye concentration and incubation temperature of 20°C. Vibrio harveyi TEMS1 was also tested for its ability to decolorize four azo dyes (Acid Black 24, Acid Blue 7, Acid Green 20, Acid Yellow 36) in addition to Acid Black 210.     

Spent Rooibos (Aspalathus linearis) Tea Biomass as an Adsorbent for Organic Dye Removal

Spent rooibos (Aspalathus linearis) tea biomass can be used as an inexpensive biosorbent for xenobiotic removal. Seventeen dyes have been tested for their affinity to spent rooibos tea biomass. Eight dyes were used to study the adsorption process in detail. The dye adsorption has been described with the Langmuir isotherm. The calculated maximum adsorption capacities reached the value of over 200 mg of dye per gram of dried rooibos biomass for Bismarck brown Y. Spent rooibos tea biomass was also magnetically modified by contact with microwave-synthesized magnetic iron oxide nano- and microparticles. This new type of magnetically responsive biocomposite material can be easily separated by means of strong permanent magnets. Both native and magnetically modified spent rooibos biomass have shown excellent adsorption capacities for various types of organic dyes, so they are highly promising adsorbents in environmental technologies for selected xenobiotic removal.     

Bioremediation of Textile Azo Dyes by Trichophyton rubrum LSK-27

Summary The potential of a recently isolated wood-degrading fungus, Trichophyton rubrum LSK-27, for effective decolorization of textile azo dyes was evaluated. Within two days of dye addition, the fungus was able to decolorize 83% of Remazol Tiefschwarz, 86% of Remazol Blue RR and 80% of Supranol Turquoise GGL in liquid cultures. The reactive dyes, Remazol Tiefschwarz and Remazol Blue, were removed by fungal biodegradation, while decolorization of the acid dye, Supranol Turquoise GGL, was accomplished mainly by bioadsorption. Therefore the fungus proved to be efficiently capable of both biodegradation and biosorption as the major dye removal mechanisms. The extent of biodegradation was associated with the levels of the extracellular ligninolytic enzymes such as manganese peroxidase and laccase.     

Use of immobilised Chlorella vulgaris for the removal of colour from textile dyes

Discharge of textile wastewater containing toxic dyes can adversely affect the aquatic ecosystems and human health. The objective of the present study was to investigate the potential use of immobilised Chlorella vulgaris UMACC 001 in removing colour from textile dyes (Supranol Red 3BW, Lanaset Red 2GA and Levafix Navy Blue EBNA) and textile wastewater (TW). Two immobilisation matrices were used, namely 1% κ-carragenan and 2% sodium alginate. Of the three dyes tested, the highest percentage of colour removal was from Lanaset Red 2GA. The cultures immobilised in 2% alginate attained the highest percentage of colour removal (44.0%) from the dye at an initial concentration of 7.25 mg L⁻¹. Immobilised cultures in alginate also removed higher percentage of colour (48.9%)from the TW, than the suspension cultures (34.9%). Aeration did not enhance the percentage of colour removal but increased the colour intensity of the wastewater instead. C. vulgaris immobilised in alginate will be useful for final polishing of textile wastewater after undergoing primary treatment before discharge.     

Decolorization of a dye industry effluent by <Emphasis Type="Italic">Aspergillus fumigatus</Emphasis> XC6

The strain Aspergillus fumigatus XC6 isolated from mildewing rice straw was evaluated for its ability to decolorize a dye industry effluent. The strain was capable of decolorizing dyes effluent over a pH range 3.0–8.0 with the dyes as sole carbon and nitrogen sources. The optimum pH was 3.0; however, supplemented with either appropriate nitrogen sources (0.2% NH₄Cl or (NH₄)₂SO₄ ) or carbon sources (1.0% sucrose or potato starch), the strain decolorized the effluent completely at the original pH of the dyes effluent. Therefore, A. fumigatus XC6 is an efficient strain for the decolorization of reactive textile dyes effluents, and it might be a practical alternative in dyeing wastewater treatment.     

Decolorization of simulated textile dye baths by crude laccases from Trametes hirsuta and Cerrena unicolor

In this study crude laccases from the white‐rot fungi Cerrena unicolor and Trametes hirsuta were tested for their ability to decolorize simulated textile dye baths. The dyes used were Remazol Brilliant Blue R (RBBR) (100 mg/L), Congo Red (12.5 mg/L), Lanaset Grey (75 mg/L) and Poly R‐478 (50 mg/L). The effect of redox mediators on dye decolorization by laccases was also assessed. C. unicolor laccase was able to decolorize all the dyes tested. It was especially effective towards Congo Red and RBBR with 91 and 80% of color removal in 19.5 h despite the fact that simulated textile dye baths were used. Also Poly R‐478 and Lanaset Grey were partially decolorized (69 and 48%, respectively). C. unicolor laccase did not need any mediators for removing the dyes. However, T. hirsuta laccase was only able to decolorize simulated Congo Red and RBBR dye baths (91 and 45%, respectively) in 19.5 h without mediators. When using mediators the decolorization capability was enhanced substantially, e.g. Poly R‐478 was decolorized by 78% in 25.5 h. On the whole, both laccases showed potential to be used in industrial applications.     

Removal of disperse dyes from textile wastewater using bio-sludge

Granular activated carbon (GAC) did not show any significant adsorption ability on the disperse dyes, while resting (living) bio-sludge of a domestic wastewater treatment plant showed high adsorption abilities on both disperse dyes and organic matter. The dye adsorption ability of bio-sludge increased by approximately 30% through acclimatization with disperse dyes, and it decreased by autoclaving. The deteriorated bio-sludge could be reused after being washed with 0.1N NaOH solution. Disperse Red 60 was more easily adsorbed onto the bio-sludge than Disperse Blue 60. The Disperse Red 60, COD, and BOD5 adsorption capacities of acclimatized, resting bio-sludge were 40.0+/-0.1, 450+/-12, and 300+/-10mg/g of bio-sludge, respectively. The GAC-SBR system could be applied to treat textile wastewater (TWW) containing disperse dyes with high dye, BOD5, COD, and TKN removal efficiencies of 93.0+/-1.1%, 88.0+/-3.1%, 92.2+/-2.7% and 51.5+/-7.0%, respectively without any excess bio-sludge production under an organic loading of 0.18 kg BOD5/m3-d. Furthermore, the removal efficiencies increased with the addition of glucose into the system. The dye, BOD5, COD, and TKN removal efficiencies of the GAC-SBR system with TWW containing 0.89 g/L glucose were 94.6+/-0.7%, 94.4+/-0.6%, 94.4+/-0.8% and 59.3+/-8.5%, respectively, under an SRT of 67+/-0.4 days.