Adsorption of heavy metal ions from aqueous solutions by activated carbon prepared from apricot stone

Apricot stones were carbonised and activated after treatment with sulphuric acid (1:1) at 200 degrees C for 24 h. The ability of the activated carbon to remove Ni(II), Co(II), Cd(II), Cu(II), Pb(II), Cr(III) and Cr(VI) ions from aqueous solutions by adsorption was investigated. Batch adsorption experiments were conducted to observe the effect of pH (1-6) on the activated carbon. The adsorptions of these metals were found to be dependent on solution pH. Highest adsorption occurred at 1-2 for Cr(VI) and 3-6 for the rest of the metal ions, respectively. Adsorption capacities for the metal ions were obtained in the descending order of Cr(VI) > Cd(II) > Co(II) > Cr(III) > Ni(II) > Cu(II) > Pb(II) for the activated carbon prepared from apricot stone (ASAC).     

Biosorption of Pb(II) and Cr(III) from aqueous solution by lichen (Parmelina tiliaceae) biomass

The biosorption characteristics of Pb(II) and Cr(III) ions from aqueous solution using the lichen (Parmelina tiliaceae) biomass were investigated. Optimum biosorption conditions were determined as a function of pH, biomass dosage, contact time, and temperature. Langmuir, Freundlich and Dubinin-Radushkevich (D-R) models were applied to describe the biosorption isotherm of the metal ions by P. tiliaceae biomass. Langmuir model fitted the equilibrium data better than the Freundlich isotherm. The monolayer biosorption capacity of P. tiliaceae biomass for Pb(II) and Cr(III) ions was found to be 75.8 mg/g and 52.1mg/g, respectively. From the D-R isotherm model, the mean free energy was calculated as 12.7 kJ/mol for Pb(II) biosorption and 10.5 kJ/mol for Cr(III) biosorption, indicating that the biosorption of both metal ions was taken place by chemical ion-exchange. The calculated thermodynamic parameters (delta G degrees , delta H degrees and delta S degrees ) showed that the biosorption of Pb(II) and Cr(III) ions onto P. tiliaceae biomass was feasible, spontaneous and exothermic under examined conditions. Experimental data were also tested in terms of biosorption kinetics using pseudo-first-order and pseudo-second-order kinetic models. The results showed that the biosorption processes of both metal ions followed well pseudo-second-order kinetics.     

Biosorption of Heavy Metals from Wastewater by Biosolids

In a study where the removal of heavy metals from wastewater is the primary aim, the biosorption of heavy metals onto biosolids prepared as Pseudomonas aeruginosa immobilized onto granular activated carbon was investigated in batch and column systems. In the batch system, adsorption equilibriums of heavy metals were reached between 20 and 50 min, and the optimal dosage of biosolids was 0.3 g/L. The biosorption efficiencies were 84, 80, 79, 59 and 42 % for Cr(VI), Ni(II), Cu(II), Zn(II) and Cd(II) ions, respectively. The rate constants of biosorption and pore diffusion of heavy metals were 0.013–0.089 min^–1 and 0.026–0.690 min^–0.5. In the column systems, the biosorption efficiencies for all heavy metals increased up to 81–100 %. The affinity of biosorption for various metal ions towards biosolids was decreased in the order: Cr = Ni > Cu > Zn > Cd.     

Equilibrium of Cu(II) and Ni(II) biosorption by marine alga Sargassum filipendula in a dynamic system: competitiveness and selectivity

The study focuses on the equilibrium of dynamic biosorption in single and binary systems containing Cu(II) and Ni(II) ions using Sargassum filipendula (a marine alga). The experiments were performed in fixed-bed columns with both single-component and bi-component metal solutions (using different molar concentrations). Experimental data were fitted with different equilibrium models such as Langmuir, Langmuir with inhibition, Jain and Snowyink and Langmuir-Freundlich equations. The biosorption of pure metal ions in solution presented adequate capacities both for Cu(II) and Ni(II). In binary solutions the preferential sorption of Cu(II) over Ni(II) was demonstrated by the displacement of Ni(II) (marked overshoot on the breakthrough curves).     

Surface treated Pteris vittata L. pinnae powder used as an efficient biosorbent of Pb(II), Cd(II), and Cr(VI) from aqueous solution

Biosorption is a surface-dependent phenomenon. Surface modifications by chemical treatment methods could either improve or reduce the biosorption capacity of potential biosorbents. In the present work, pristine Pteris vittata L. pinnae (PPV) powder was treated separately with sodium hydroxide (NaOH), calcium chloride (CaCl₂), and nitric acid (HNO₃). The pristine and treated biosorbents were used to assess the biosorption of Pb(II), Cd(II), and Cr(VI) as a function of pH. Kinetics and adsorption isotherms were studied. Attenuated total reflectance Fourier transform infrared (ATR-FTIR) spectroscopy and scanning electron microscope combined with energy dispersive x-ray (SEM-EDX) spectroscopic techniques were used to characterize the biosorbents before and after chemical treatments. The possible functional groups contributing to the metal sorption were identified. Results revealed favorable biosorption of Pb(II), Cd(II), and Cr(VI) described by pseudo-second order kinetics. NaOH-treated P. vittata (NPV) showed higher biosorption capacity for Pb(II) and Cd(II) compared to that of PPV. ATR-FTIR studies indicated that -OH, -COOH, and -NH₂ groups were mainly involved in Cr(VI) and -OH in Pb(II) and Cd(II) biosorption. The enhanced efficiency of NPV and CaCl₂ treated P. vittata (CPV) in the uptake of Pb(II) and Cd(II) compared to PPV can be associated with their altered physicochemical characters.     

Comparative study of Cd(II) and Cr(VI) biosorption on Staphylococcus xylosus and Pseudomonas sp. in single and binary mixtures

Biosorption of Cd(II) and Cr(VI) ions in single solutions using Staphylococcus xylosus and Pseudomonas sp., and their selectivity in binary mixtures was investigated. Langmuir and Freundlich models were applied to describe metal biosorption and the influence of pH, biomass concentration and contact time was determined. Maximum uptake capacity of cadmium was estimated to 250 and 278 mg g(-1), whereas that of chromium to 143 and 95 mg g(-1) for S. xylosus and Pseudomonas sp., respectively. In binary mixtures with Cd(II) ions as the dominant species, there is a profound selectivity for cadmium biosorption, reaching 96% and 89% for Pseudomonas sp. and S. xylosus, respectively, at 10 mg l(-1) Cd(II) and 5 mg l(-1) Cr(VI). Interesting, when chromium (VI) ions are the dominant species, there is selectivity towards chromium around 92% with S. xylosus only.     

Arthrospira (Spirulina) platensis: An effective biosorbent for nutrients

Arthrospira (Spirulina) platensis was tested for biosorption properties. Preliminary experiments concerning biosorption kinetics were performed on Cr(III) ions. Equilibrium of biosorption was tested for Cr(III), Mn(II) and Mg(II) ions, since these elements are crucial for animals with metabolic disorders. In our study, Spirulina was proposed as a feed additive for animals suffering from diseases characterized by insulin dysregulation, abnormal adipose distribution and a high risk for laminitis. Maximum biosorption capacity of A. platensis, determined from Langmuir equation, was 45.2 for Cr(III), 44.3 for Mn(II) and 42.0 mg/g for Mg(II) ions. Biosorption of Mg(II) ions by microalga has never been studied so far. Finally, the raw and enriched microalgal biomass was examined by ICP-OES to determine its multielamental analysis before and after biosorption, FTIR to indicate functional groups that participated in biosorption and SEM-EDX to illustrate the binding of metal ions on the surface of algal biomass. ICP-OES showed that the content of elements significantly increased in the enriched A. platensis. FTIR spectroscopy evidenced that biosorption of metal ions was mainly due to carboxylate groups present on the microalgal cell wall. SEM analysis clearly showed that biosorption occurred. Arthrospira platensis turned out to be a good biosorbent of metal ions.     

Determination of the biosorption heats of heavy metal ions on Zoogloea ramigera and Rhizopus arrhizus

The biosorption of Fe(III), Cr(VI), Pb(II), Cu(II) and Ni(II) ions on Zoogloea ramigera (activated sludge bacterium) and Rhizopus arrhizus (filamentous fungus) has been studied as a function of initial metal ion concentration and temperature. The applicability of the Langmuir model for each metal-microorganism system has been tested at different temperatures. The enthalpy change for the biosorption process has been evaluated by using the Langmuir constant b, related to the energy of adsorption. Thermodynamic parameters indicate the exothermic nature of Cu(II) and Ni(II) biosorption on both microorganisms. Fe(III), Cr(VI) and Pb(II) biosorption is determined to be an endothermic process since increased binding occurs as the temperature is increased in the range 15-45 degrees C.     

Biosorption of cadmium(II), lead (II) and copper(II) with the filamentous fungus Phanerochaete chrysosporium

The biosorption from artificial wastewaters of heavy metals (Cd(II), Pb(II) and Cu(II)) onto the dry fungal biomass of Phanerochaete chryosporium was studied in the concentration range of 5-500 mg l(-1). The maximum absorption of different heavy metal ions on the fungal biomass was obtained at pH 6.0 and the biosorption equilibrium was established after about 6 h. The experimental biosorption data for Cd(II), Pb(II) and Cu(II) ions were in good agreement with those calculated by the Langmuir model.     

Spontaneous Cr(VI) and Cd(II) biosorption potential of native pinnae tissue of Pteris vittata L., a tropical invasive pteridophyte

Heavy metal pollution is a prevalent and critical environmental concern. Its rampancy is attributed to indiscriminate anthropogenic activities. Several technologies including biosorption have been continuously researched upon to overcome the limitations of the conventional method of treatments in removal of heavy metals. Biosorption technology involves the application of a biomass in its nonliving form. Pteris vittata L., a pteridophyte, considered as an invasive weed was investigated in the present study as a potential decontaminant of toxic metals, Cr(VI) and Cd(II). The adsorption capacity of the biosorbent for Cr(VI) and Cd(II) under equilibrium conditions was investigated. The morphology, elemental composition, functional groups, and thermal stability of the biosorbent before and after metal loading were evaluated. At 303?K and an equilibrium time of 120?min, the maximum loading of Cr(VI) on the biosorbent was estimated to be 166.7?mg/g at pH 2 and Cd(II) to be 31.3?mg/g at pH 6. Isotherm models, kinetic studies, and thermodynamic studies indicated the mechanisms, chemisorption, ion exchange and intraparticle diffusion, controlling the Cr(VI) and Cd(II) uptake, respectively. The interactive effect of multi-metal ions in binary component systems was synergistic for Cd(II) uptake. The results validate the toxic metal removal potency of the biosorbent.     

Competitive adsorption of Cu(II) and Cd(II) ions by chitosan crosslinked with epichlorohydrin-triphosphate

In this study, chitosan (CTS) was crosslinked with both epichlorohydrin (ECH) and triphosphate (TPP), by covalent and ionic crosslinking reactions, respectively. The resulting adsorbent (CTS-ECH-TPP) was characterized by SEM, CHN, EDS, FT-IR and TGA analyses, and tested for metal adsorption. The adsorbent was used in batch experiments to evaluate the adsorption of Cu(II) and Cd(II) ions in single and binary metal solutions. In single metal solutions the maximum adsorption capacities for Cu(II) and Cd(II) ions, obtained by Langmuir model, were 130.72 and 83.75 mg g?1, respectively. Adsorption isotherms for binary solutions showed that the presence of Cu(II) decreased Cd(II) adsorption due to a significant competition effect, that is, the adsorbent was selective towards Cu(II) rather than Cd(II).     

Immobilized chitosan as biosorbent for the removal of Cd(II), Cr(III) and Cr(VI) from aqueous solutions

The generation of layer-by-layer silicate-chitosan composite biosorbent was studied. The films were evaluated on its stability regarding the polymer leakage and its capability in the removal of Cd(II), Cr(III) and Cr(VI) from an aqueous solution. SEM, EDAX and ATR-IR techniques were applied for material characterization. Silicate-chitosan films with a final layer of silicate demonstrated chitosan retention and had better sorption capacities than those without it. For metal species, such as Cd(II) and Cr(III), the greatest adsorption was obtained when the pH of the solution was 7. When Cr(VI) was evaluated, pH 4 was the optimal for its adsorption. Langmuir and Freundlich isotherms were modeled for the equilibrium data. An 80% of the adsorbed metal was recovered by HNO(3) incubation. This non-covalent immobilization method allowed chitosan surface retention and did not affect its adsorption properties. The use of a coated surface would facilitate sorbent removal from medium after adsorption.     

Biosorption of Ni, Cr and Cd by metal tolerant Aspergillus niger and Penicillium sp. using single and multi-metal solution

Fungi including Aspergillus and Penicillium, resistant to Ni2+, Cd2+, and Cr6+ were isolated from soil receiving long-term application of municipal wastewater mix with untreated industrial effluents of Aligarh, India. Metal tolerance in term of minimum inhibitory concentration (MIC) was 125-550 microg/ml for Cd, 300-850 microg/ml for Ni and 300-600 microg/ml for Cr against test fungi. Two isolates, Aspergillus niger and Penicillium sp. were tested for their Cr, Ni and Cd biosorption potential using alkali treated, dried and powdered mycelium. Biosorption experiment was conducted in 100 ml of solution at three initial metal concentrations i.e., 2, 4 and 6 mM with contact time (18 hr) and pretreated fungal biomass (0.1g) at 25 degrees C. Biosorption of all metals was found higher at 4 mM initial metal concentration as compared to biosorption at 2 and 6 mM concentrations. At 4 mM initial metal concentration, chromium biosorption was 18.05 and 19.3 mg/g of Aspergillus and Penicillium biomasses, respectively. Similarly, biosorption of Cd and Ni ions was also maximum at 4 mM initial metal concentration by Aspergillus (19.4 mg/g for Cd and 25.05 mg/g of biomass for Ni) and Penicillium (18.6 mg/g for Cd and 17.9 mg/g of biomass for Ni). In general, biosorption of metal was influenced by initial metal concentration and type of the test fungi. The results indicated that fungi of metal contaminated soil have high level of metal tolerance and biosorption properties.     

Use of silica-immobilized humin for heavy metal removal from aqueous solution under flow conditions

Humin extracted from Sphagnum peat moss was immobilized in a silica matrix and column experiments were performed in order to evaluate the removal and recovery of metal ions from aqueous solution under flow conditions. These experiments also allowed testing the recycling capacity of the column. Single-element solutions of Cu(II) and Pb(II), and a multi-metal solution containing Cd(II), Cu(II), Pb(II), Ni(II), and Cr(III) were passed through the columns at a flow rate of 2 ml/min. A 0.5 M sodium citrate solution was used as the stripping agent in the metal-ion recovery process. Humin immobilized in the silica matrix exhibited a similar, and in some cases, even a higher capacity than other biosorbents for the removal of metal ions from aqueous solutions under flow conditions. The sodium citrate was effective in removing Cu(II), Pb(II), Cd(II), and Ni(II) from the metal saturated column. The selectivity of the immobilized biomass was as follows: Cr(III)>Pb(II)>Cu(II)>Cd(II)>Ni(II). This investigation provides a new, environmentally friendly and cost-effective possibility to clean up heavy-metal contaminated wastewaters by using the new silica-immobilized humin material.     

Biosorption of Pb(II) and Cu(II) by activated sludge in batch and continuous-flow stirred reactors

Biosorption of Pb(II) and Cu(II) ions in single component and binary systems was studied using activated sludge in batch and continuous-flow stirred reactors. In biosorption experiments, the activated sludge in three different phases of the growth period was used: growing cells; resting cells; dead or dried cells. Because of the low adsorption capacity of the non-viable activated sludge especially in the case of Pb(II) ions, biosorption of the Cu(II) and Pb(II) ions from the binary mixtures was carried out by using the resting cells. The biosorption data fitted better with the Freundlich adsorption isotherm model. Using a mathematical model based on continuous system mass balance for the liquid phase and batch system mass balance for the solid phase, the forward rate constants for biosorption of Pb(II) and Cu(II) ions were 0.793 and 0.242 1 (mmolmin)(-1), respectively.     

Enhancement of Lead(II) Biosorption by Microalgal Biomass Immobilized onto Loofa (Luffa cylindrica) Sponge

A unicellular green microalga, Chlorella sorokiniana, was immobilized on loofa (Luffa cylindrica) sponge and successfully used as a new biosorption system for the removal of lead(II) ions from aqueous solutions. The biosorption of lead(II) ions on both free and immobilized biomass of C. sorokiniana was investigated using aqueous solutions in the concentration range of 10–300 mg/L. The biosorption of lead(II) ions by C. sorokiniana biomass increased as the initial concentration of lead(II) ions increased in the medium. The maximum biosorption capacity for free and immobilized biomass of C. sorokiniana was found to be 108.04 and 123.67 mg lead(II)/g biomass, respectively. The biosorption kinetics were found to be fast, with 96 % of adsorption within the first 5 min and equilibrium reached at 15 min. The adsorption of lead(II) both by free and immobilized C. sorokiniana biomass followed the Langmuir isotherm. The biosorption capacities were detected to be dependent on the pH of the solution; and the maximum adsorption was obtained at a solution pH of about 5. The effect of light metal ions on lead(II) uptake was also studied and it was shown that the presence of light metal ions did not significantly affect lead(II) uptake. The loofa sponge‐immobilized C. sorokiniana biomass could be regenerated using 0.1 M HCl, with up to 99 % recovery. The desorbed biomass was used in five biosorption‐desorption cycles, and no noticeable loss in the biosorption capacity was observed. In addition, fixed bed breakthrough curves for lead(II) removal were presented. These studies demonstrated that loofa sponge‐immobilized biomass of C. sorokiniana could be used as an efficient biosorbent for the treatment of lead(II) containing wastewater.     

Biosorption of nickel and cadmium by metal resistant bacterial isolates from agricultural soil irrigated with industrial wastewater

Agricultural soil irrigated with industrial wastewater (more than two decades) analysed for heavy metals revealed high levels of Fe, Cr, Cu, Zn, Ni and Cd. Out of a total of 40 bacterial isolates obtained from these soils, 17 belonged to the family enterobacteriaceae and 10 were Pseudomonas spp. A maximum MIC of 200 for Cd, 400 for Zn and Cu, 800 for Ni, and 1600 microg/ml for Pb was observed. Biosorption of Ni and Cd studies over a range of metal ion concentrations with Escherichia coli WS11 both in single and bi-metal systems showed that the adsorption of Cd and Ni was dependent on the concentrations and followed the Freundlich adsorption isotherm. The biosorption of Ni increased from 6.96 to 55.31 mg/g of cells, and Cd from 4.96 to 45.37 mg/g of cells at a concentration ranging from 50 to 400 microg/ml after 2h of incubation in a single metal solution. A further increase in incubation time had no significant effect on the biosorption of metals.     

Concurrent sorption of Zn(II), Cu(II) and Co(II) by Oscillatoria angustissima as a function of pH in binary and ternary metal solutions

This paper reports biosorption of Zn(II), Cu(II) and Co(II) onto O. angustissima biomass from single, binary and ternary metal solutions, as a function of pH and metal concentrations via Central Composite Design generated by statistical software package Design Expert 6.0. The experimental design revealed that metal interactions could be best studied at lower pH range i.e. 4.0-5.0, which facilitates adequate availability of all the metal ions. The sorption capacities for single metal decreased in the order Zn(II)>Co(II)>Cu(II). In absence of any interfering metals, at pH 4.0 and an initial metal concentration of 0.5 mM in the solution, the adsorption capacities were 0.33 mmol/g Zn(II), 0.26 mmol/g Co(II) and 0.12 mmol/g Cu(II). In a binary system, copper inhibited both Zn(II) and Co(II) sorption but the extent of inhibition of former was greater than the latter; sorption values being 0.14 mmol/g Zn(II) and 0.27 mmol/g Co(II) at initial Zn(II) and Co(II) concentration of 1.5 mM each, pH 4.0 and 1mM Cu(II) as the interfering metal. Zn(II) and Co(II) were equally antagonistic to each others sorption; Zn(II) and Co(II) sorption being 0.23 and 0.24 mmol/g, respectively, at initial metal concentration of 1.5 mM each, pH 4.0 and 1mM interfering metal concentration. In contrast, Cu(II) sorption remained almost unaffected at lower concentrations of the competing metals. Thus, in binary system inhibition dominance observed was Cu(II)>Zn(II), Cu(II)>Co(II) and Zn(II) approximately Co(II), due to this the biosorbent exhibited net preference/affinity for Cu(II) sorption over Zn(II) or Co(II). Hence, the affinity series showed a trend of Cu(II)>Co(II)>Zn(II). In a ternary system, increasing Co(II) concentration exhibited protection against the inhibitory effect of Cu(II) on Zn(II) sorption. On the other hand, the inhibitory effect of Zn(II) and Cu(II) on Co(II) sorption was additive. The model equation for metal interactions was found to be valid within the design space.     

Metal tolerance and biosorption potential of filamentous fungi isolated from metal contaminated agricultural soil

Heavy metal analysis of agricultural field soil receiving long-term (>20 years) application of municipal and industrial wastewater showed two- to five-fold accumulation of certain heavy metals as compared to untreated soil. Metal-resistant fungi isolated from wastewater-treated soil belonged to genera Aspergillus, Penicillium, Alternaria, Geotrichum, Fusarium, Rhizopus, Monilia and Trichoderma. Minimum inhibitory concentrations (MIC) for Cd, Ni, Cr, Cu, and Co were determined. The MIC ranged from 0.2 to 5 mg ml(-1) for Cd, followed by Ni (0.1-4 mg ml(-1)), Cr (0.3-7 mg ml(-1)), Cu (0.6-9 mg ml(-1)) and for Co (0.1-5 mg ml(-1)) depending on the isolate. Aspergillus and Rhizopus isolates were tested for their metal biosorption potential for Cr and Cd in vitro. Biosorption experiments were conducted with initial metal concentrations of 2, 4, 6 and 8 mM with a contact time of 4 h and wet fungal biomass (1-5 g) at 25 degrees C. Maximum biosorption of Cr and Cd ions was found at 6 mM initial metal concentration. Aspergillus sp.1 accumulated 1.20 mg of Cr and 2.72 mg of Cd per gram of biomass. Accumulation of these two metals by very tolerant Aspergillus sp.2 isolate was at par with relatively less tolerant Aspergillus sp.1 isolate. Rhizopus sp. accumulated 4.33 mg of Cr and 2.72 mg of Cd per g of biomass. The findings indicated promising biosorption of cadmium and chromium by the Rhizopus and Aspergillus spp. from aqueous solution. There is little, if any, correlation between metal tolerance and biosorption properties of the test fungi.     

Adsorption of Cu(II), Ni(II) and Zn(II) on modified jute fibres

The potential of a lignocellulosic fibre, jute, was assessed for adsorption of heavy metal ions like Cu(II), Ni(II) and Zn(II) from their aqueous solutions. The fibre was also used as adsorbent after chemically modifying it by two different techniques viz, loading of a dye with specific structure, C.I. Reactive Orange 13, and oxidising with hydrogen peroxide. Both the modified jute fibres gave higher metal ion adsorption. Thus, the dye loaded jute fibres showed metal ion uptake values of 8.4, 5.26 and 5.95 mg/g for Cu(II), Ni(II) and Zn(II), respectively, while the corresponding values for oxidised jute fibres were 7.73, 5.57 and 8.02 mg/g, as against 4.23, 3.37 and 3.55 mg/g for unmodified jute fibres. Adsorption isotherm models indicated best fit for Langmuir model for the modified jute fibres. The adsorption values decreased with lowering of pH. The desorption efficiency, regenerative and reuse capacity of these adsorbents were also assessed for three successive adsorption-desorption cycles. The adsorptive capacity was retained only when the caustic soda regeneration is carried out as an intermediate step after desorption. Possible mechanism has been given.