Thermal behaviour of cubic phases rich in 1-monooleoyl-rac-glycerol in the ternary system. 1-monooleoyl-rac-glycerol/n-octyl-beta-D-glucoside/water.

Using synchrotron X-ray diffraction the thermal behaviour was studied of the cubic phases in the 1-monooleoyl-rac-glycerol (MO)/n-octyl-beta-d-glucopyranoside (OG)/2H2O system with 58 or 45 wt % MO concentration and varying OG/2H2O contents. These MO contents correspond to a Pn3m cubic single-phase or a Pn3m cubic phase in excess water on the binary MO/water axis of the ternary phase diagram. The cubic liquid crystalline phases are stable with small fractions of OG, while higher OG concentrations trigger a cubic-to-lamellar phase transition. Moreover, with increasing OG concentration the initial Pn3m structure is completely converted to an Ia3d structure prior to the Lalpha phase being formed. Upon heating this effect is reversed, resulting in an Ia3d-to-Pn3m phase transition. For some samples additional peaks were observed in the diffractograms upon heating, resulting from the metastability notoriously shown by bicontinuous cubic phases. This judgement is supported by the fact that upon cooling these peaks were absent. Remarkably, both the Ia3d and the Pn3m cubic structures could be in equilibrium with excess water in this ternary system. A comparison is made with previous results on n-dodecyl-beta-d-maltoside (DM), showing that cubic phases with OG have higher thermal and compositional stability than with DM.     

Accelerated formation of cubic phases in phosphatidylethanolamine dispersions.

By means of x-ray diffraction we show that several sodium salts and the disaccharides sucrose and trehalose strongly accelerate the formation of cubic phases in phosphatidylethanolamine (PE) dispersions upon temperature cycling through the lamellar liquid crystalline-inverted hexagonal (Lalpha-HII) phase transition. Ethylene glycol does not have such an effect. The degree of acceleration increases with the solute concentration. Such an acceleration has been observed for dielaidoyl PE (DEPE), dihexadecyl PE, and dipalmitoyl PE. It was investigated in detail for DEPE dispersions. For DEPE (10 wt% of lipid) aqueous dispersions at 1 M solute concentration, 10-50 temperature cycles typically result in complete conversion of the Lalpha phase into cubic phase. Most efficient is temperature cycling executed by laser flash T-jumps. In that case the conversion completes within 10-15 cycles. However, the cubic phases produced by laser T-jumps are less ordered in comparison to the rather regular cubic structures produced by linear, uniform temperature cycling at 10 degrees C/min. Temperature cycles at scan rates of 1-3 degrees C/min also induce the rapid formation of cubic phases. All solutes used induce the formation of Im3m (Q229) cubic phase in 10 wt% DEPE dispersions. The initial Im3m phases appearing during the first temperature cycles have larger lattice parameters that relax to smaller values with continuation of the cycling after the disappearance of the Lalpha phase. A cooperative Im3m --> Pn3m transition takes place at approximately 85 degrees C and transforms the Im3m phase into a mixture of coexisting Pn3m (Q224) and Im3m phases. The Im3m/Pn3m lattice parameter ratio is 1. 28, as could be expected from a representation of the Im3m and Pn3m phases with the primitive and diamond infinite periodic minimal surfaces, respectively. At higher DEPE contents ( approximately 30 wt%), cubic phase formation is hindered after 20-30 temperature cycles. The conversion does not go through, but reaches a stage with coexisting Ia3d (Q230) and Lalpha phases. Upon heating, the Ia3d phase cooperatively transforms into a mixture of, presumably, Im3m and Pn3m phases at about the temperature of the Lalpha-HII transition. This transformation is readily reversible with the temperature. The lattice parameters of the DEPE cubic phases are temperature-insensitive in the Lalpha temperature range and decrease with the temperature in the range of the HII phase.     

Cubic topology in surfactant and lipid mixtures

Ternary systems of palmitoyl-oleoyl-phosphatidylcholine (POPC) and the non-ionic surfactant C₁₂EO₂ (di-ethylene-oxide-mono-dodecyl-ether) in water have been studied with optical microscopy, NMR, DSC and X-rays from ambient temperatures to 45 °C. Below 29 °C the system is in the lamellar liquid crystalline state. Between 30 and 32 °C it transforms into a cubic Ia3d structure which converts into the cubic Pn3m phase at 39 °C. The transitions are fully reversible. An epitaxial relationship between all three phases was found, which is an elegant and convenient way to rearrange molecules from lamellar bilayers to a network of curved surfaces. The la3d (Q²³⁰) to Pn3m (Q²²⁴) transition occurs without measurable enthalpy change. This, together with the metric relation of 1.60 between the cubic lattice constants is strong evidence for a Bonnet transformation, where the structural changes occur without change in curvature. The potential significance of the cubic phases as intermediate structures for biological processes, e. g. transport across a bilayer or fusion of membranes, are discussed.     

Temperature- and pressure-dependent phase behavior of monoacylglycerides monoolein and monoelaidin.

We used x-ray and neutron diffraction to study the temperature- and pressure-dependent structure and phase behavior of the monoacylglycerides 1-monoelaidin (ME) and 1-monoolein (MO) in excess water. The monoacylglycerides were chosen for investigation of their phase behavior because they exhibit mesomorphic phases with one-, two-, and three-dimensional periodicity, such as lamellar, an inverted hexagonal and bicontinuous cubic phases, in a rather easily accessible temperature and pressure range. We studied the structure, stability, and transformations of the different phases over a wide temperature and pressure range, explored the epitaxial relations that exist between different phases, and established a relationship between the chemical structure of the lipid molecules and their phase behavior. For both systems, a temperature-pressure phase diagram has been determined in the temperature range from 0 to 100 degrees C at pressures from ambient up to 1400 bar, and drastic differences in phase behavior are found for the two systems. In MO-water dispersions, the cubic phase Pn3m extends over a large phase field in the T,p-plane. At temperatures above 95 degrees C, the inverted hexagonal phase is found. In the lower temperature region, a crystalline lamellar phase is induced at higher pressures. The phases found in ME-water include the lamellar crystalline Lc phase, the L beta gel phase, the L alpha liquid-crystalline phase, and two cubic phases belonging to the crystallographic space groups Im3m and Pn3m. In addition, the existence of metastable phases has been exploited. Between coexisting metastable cubic structures, a metric relationship has been found that is predicted theoretically on the basis of the curvature elastic energy approximation only.     

An inverse face-centered cubic phase formed by diacylglycerol-phosphatidylcholine mixtures

Fully hydrated unsaturated diacylglycerol-phosphatidylcholine mixtures are found to adopt an inverse face-centered cubic phase, of crystallographic cubic aspect 15. The same behavior is observed for either the 1,2- or 1,3-isomer of the diacylglycerol. This Q15 cubic phase, of probable space group Fd3m (Q227), occurs between an inverse hexagonal (HII) phase and an inverse micellar (L2) solution, with increasing diacylglycerol concentration, which implies that the mean curvature of the interface is more negative than that of the HII phase. This behavior is quite different from that of the more usual bicontinuous inverse cubic phases Pn3m (Q224), Im3m (Q229), and Ia3d (Q230), which normally occur between the lamellar L alpha and the HII phases. One possible structure for the Fd3m cubic phase has recently been proposed (Mariani, P., Luzzati, V., & Delacroix, H. (1988) J. Mol. Biol. 204, 165-189), consisting of tetrahedrally arranged clusters of inverse micelles surrounded by a continuous cage of tetrahedrally connected water/lipid (inverse) channels.     

Incorporation of alpha-chymotrypsin into the 3D channels of bicontinuous cubic lipid mesophases

The effects of protein entrapment on the structure and phase behavior of periodically curved lipid mesostructures have been examined by synchrotron small-angle X-ray diffraction and FT-IR spectroscopy. The study was directed towards a better understanding of the effect of confinement in a lipid environment on the stability and unfolding behavior of alpha-chymotrypsin, and, vice versa, the effect of the entrapped protein on the lipid's mesophase structure and temperature- and pressure-dependent phase behavior. We compare the interaction of protein molecules of two different sizes (cytochrome c, 12.4 kDa, and alpha-chymotrypsin, 25.8 kDa) with the cubic Ia3d phase of monoolein (MO), which forms spontaneously in water. The cubic structure changes significantly when cyt c is incorporated: above a protein concentration of 0.2 wt.%, the interaction between the positively charged protein and the lipid headgroups leads to an increase in interfacial curvature which promotes the formation of a new micellar cubic phase, presumably of crystallographic space group P4(3)32, which the lipid system does not form on its own. The larger alpha-chymotrypsin leads to a different scenario. On the basis of an examination of the calculated geometric parameters and water volume fractions, it is concluded that the alpha-chymotrypsin molecules cannot be located exclusively in the water channels of the cubic Ia3d or P4(3)32 phases, but rather form new, less ordered (presumably cubic Pn3m) structures. The new structure disappears above the unfolding temperature of chymotrypsin and exhibits a pressure stability, which-- in contrast to cyt c in MO-- decreases with increasing chymotrypsin concentration in the system. While the secondary structure of cyt c remains unaffected in the confining lipid environment, the structure of alpha-chymotrypsin gets destabilized slightly, and the protein tends to aggregate even at relatively low concentrations.     

The temperature-composition phase diagram and mesophase structure characterization of monopentadecenoin in water.

The temperature-composition phase diagram of monopentadecenoin, a monoacylglycerol with a cis monounsaturated fatty acid 15 carbon atoms long (C15:1c10) in water was constructed using x-ray diffraction. Low- and wide-angle diffraction patterns were collected from samples of fixed hydration as a function of temperature in the heating direction on x-ray-sensitive film. The temperature and hydration ranges investigated were 0-104 degrees C and 0-60% (w/w) water, respectively. The phases identified in the system include the lamellar crystalline phase, the lamellar liquid crystalline phase, the fluid isotropic phase, and two inverted cubic phases belonging to space groups la3d (Q230) and Pn3m (Q244). Particular attention has been devoted to the issues of phase equilibrium, phase boundary verification, and structure characterization. The phase diagrams of monopentadecenoin, monomyristolein (C14:1c9), and monoolein (C18:1c9) are compared, and the impact of molecular structure on mesophase stability and structure is discussed.     

Phase equilibria of membrane lipids from Acholeplasma laidlawii: importance of a single lipid forming nonlamellar phases

A basis for the reorganization of the bilayer structure in biological membranes is the different aggregate structures formed by lipids in water. The phase equilibria of all individual lipids and several in vivo polar lipid mixtures from acyl chain modified membranes of Acholeplasma laidlawii were investigated with different NMR techniques. All dioleoyl (DO) polar lipids, except monoglucosyldiglyceride (MGDG), form lamellar liquid crystalline (L alpha) phases only. The phase diagram of DOMGDG reveals reversed cubic (III), reversed hexagonal (HII), and L alpha phases. In mixtures of DOMGDG and dioleoyldiglycosyldiglyceride (DODGDG), the formation of an III (or HII) phase is enhanced by DOMGDG and low hydration or high temperatures. For in vivo mixtures of all polar DO lipids, a transition from an L alpha to an III phase is promoted by low hydration or high temperatures (50 degrees C). The phospholipids are incorporated in this III phase. Likewise, III and HII phases are formed at similar temperatures in a series of in vivo mixtures with different extents of acyl chain unsaturation. However, their melting temperatures (Tm) vary in an expected manner. All cubic and hexagonal phases, except the III phase with DOMGDG, exist in equilibrium with excess water. The maximum hydration of MGDG and DGDG is similar and increases with acyl chain unsaturation but is substantially lower than that for, e.g., phosphatidylcholine. The translational diffusion of the lipids in the cubic phases is rapid, implying bicontinuous structures. However, their appearances in freeze-fracture electron microscope pictures are different. The III phase of DOMGDG belongs to the Ia3d space group.(ABSTRACT TRUNCATED AT 250 WORDS)     

Formation of monolayers and bilayer foam films from lamellar,inverted hexagonal and cubic lipid phases

This study revealed large distinctions between the lamellar and non-lamellar liquid crystalline lipid phases in their spreading at the air/water interface and propensity to form bilayer foam films. Comparative measurements were made for the lamellar L(alpha), the inverted hexagonal H(II) and the bicontinuous cubic Pn3m phases of the phospholipid dipalmitoleoylphosphatidylethanolamine (DPoPE). With regard to monolayer formation, followed as the decrease of surface tension with time, the best spreading (lowest surface tension) was observed for the L(alpha) phase, and poorest spreading (highest surface tension) was recorded for the H(II) phase. The cubic Pn3m phase of DPoPE, induced by temperature cycling, retained an intermediate position between the L(alpha) and H(II) phases. According to their ability to lower surface tension and disintegrate at the air/water interface, the three phases thus order as L(alpha)>Pn3m>H(II). Clearly expressed threshold (minimum) bulk lipid concentrations, C(t), required for formation of stable foam bilayers from these phases, were determined and their values were found to correlate well with the bulk lipid phase behaviour. The C(t) values for L(alpha) and H(II) substantially increase with the temperature. Their Arrhenius plots, ln C(t) versus 1/ T, are linear and intersect at approximately 36-37 degrees C, coinciding with the onset of the bulk L(alpha)-->H(II) phase transition, as determined by differential scanning calorimetry. However, the C(t) value for the Pn3m phase, equal to 30 micro g/mL, was found to be constant over the whole range investigated between 20 degrees C and 50 degrees C. The horizontal C(t) versus T plot for the Pn3m phase crosses the respective plot for the L(alpha) phase at the temperature bounding from below the hysteretic loop of the L(alpha)<-->H(II) transition (approximately 26 degrees C), thus providing a certain insight about the thermodynamic stability of the Pn3m phase relative to the L(alpha) phase. The established strong effect of the particular lipid phase on the formation of monolayers and stable black foam films should be of importance in various in vitro and in vivo systems, where lipid structures are in contact with interfaces and disintegrate there to different extents.     

Liquid crystalline phase and gel-sol transitions for concentrated microcrystalline cellulose (MCC)/1-ethyl-3-methylimidazolium acetate (EMIMAc) solutions

Liquid crystalline (LC) phase transition and gel-sol transition in the solutions of microcrystalline cellulose (MCC) and ionic liquid (1-ethyl-3-methylimidazolium acetate, EMIMAc) have been investigated through a combination of polarized optical microscope (POM) observation and rheological measurements. Molecular LC phase forms at the 10 wt % cellulose concentration, as observed by POM, whereas the critical gel point is 12.5 wt % by rheological measurements according to the Winter and Chambon theory, for which the loss tangent, tan δ, shows frequency independence. Dramatic decreases of G' and G' in the phase transition temperature range during temperature sweep are observed due to disassembling of the LC domain junctions. The phase diagram describing the LC phase and gel-sol transitions is obtained and the associated mechanisms are elucidated. A significant feature shown in the phase diagram is the presence of a narrow lyotropic LC solution region, which potentially has a great importance for the cellulose fiber wet spinning.     

Polymorphism, mesomorphism, and metastability of monoelaidin in excess water.

The polymorphic and metastable phase behavior of monoelaidin dry and in excess water was studied by using high-sensitivity differential scanning calorimetry and time-resolved x-ray diffraction in the temperature range of 4 degrees C to 60 degrees C. To overcome problems associated with a pronounced thermal history-dependent phase behavior, simultaneous calorimetry and time-resolved x-ray diffraction measurements were performed on individual samples. Monoelaidin/water samples were prepared at room temperature and stored at 4 degrees C for up to 1 week before measurement. The initial heating scan from 4 degrees C to 60 degrees C showed complex phase behavior with the sample in the lamellar crystalline (Lc0) and cubic (Im3m, Q229) phases at low and high temperatures, respectively. The Lc0 phase transforms to the lamellar liquid crystalline (L alpha) phase at 38 degrees C. At 45 degrees C, multiple unresolved lines appeared that coexisted with those from the L alpha phase in the low-angle region of the diffraction pattern that have been assigned previously to the so-called X phase (Caffrey, 1987, 1989). With further heating the X phase converts to the Im3m cubic phase. Regardless of previous thermal history, cooling calorimetric scans revealed a single exotherm at 22 degrees C, which was assigned to an L alpha+cubic (Im3m, Q229)-to-lamellar gel (L beta) phase transition. The response of the sample to a cooling followed by a reheating or isothermal protocol depended on the length of time the sample was incubated at 4 degrees C. A model is proposed that reconciles the complex polymorphic, mesomorphic, and metastability interrelationships observed with this lipid/water system. Dry monoelaidin exists in the lamellar crystalline (beta) phase in the 4 degrees C to 45 degrees C range. The beta phase transforms to a second lamellar crystalline polymorph identified as beta* at 45 degrees C that subsequently melts at 57 degrees C. The beta phase observed with dry monoelaidin is identical to the LcO phase formed by monoelaidin that was dispersed in excess water and that had not been previously heated.     

The effect of peptide/lipid hydrophobic mismatch on the phase behavior of model membranes mimicking the lipid composition in Escherichia coli membranes

The effect of hydrophobic peptides on the lipid phase behavior of an aqueous dispersion of dioleoylphosphatidylethanolamine and dioleoylphosphatidylglycerol (7:3 molar ratio) was studied by (31)P NMR spectroscopy. The peptides (WALPn peptides, where n is the total number of amino acid residues) are designed as models for transmembrane parts of integral membrane proteins and consist of a hydrophobic sequence of alternating leucines and alanines, of variable length, that is flanked on both ends by tryptophans. The pure lipid dispersion was shown to undergo a lamellar-to-isotropic phase transition at approximately 60 degrees C. Small-angle x-ray scattering showed that at a lower water content a cubic phase belonging to the space group Pn3m is formed, suggesting also that the isotropic phase in the lipid dispersion represents a cubic liquid crystalline phase. It was found that the WALP peptides very efficiently promote formation of nonlamellar phases in this lipid system. At a peptide-to-lipid (P/L) molar ratio of 1:1000, the shortest peptide used, WALP16, lowered the lamellar-to-isotropic phase transition by approximately 15 degrees C. This effect was less for longer peptides. For all of the WALP peptides used, an increase in peptide concentration led to a further lowering of the phase transition temperature. At the highest P/L ratio (1:25) studied, WALP16 induced a reversed hexagonal liquid crystalline (H(II)) phase, while the longer peptides still promoted the formation of an isotropic phase. Peptides with a hydrophobic length larger than the bilayer thickness were found to be unable to inhibit formation of the isotropic phase. The results are discussed in terms of mismatch between the hydrophobic length of the peptide and the hydrophobic thickness of the lipid bilayer and its consequences for lipid-protein interactions in membranes.     

Synthesis and mesomorphic properties of glycosyl dialkyl- and diacyl-glycerols bearing saturated, unsaturated and methyl branched fatty acid and fatty alcohol chains. Part II. Mesomorphic properties

The biophysical properties of a series of glycosyl dialkyl- and diacyl-glycerols bearing unsaturated or chiral methyl branched chains in the tail, and di- and trisaccharide carbohydrate headgroups are described. Thermotropism was investigated by polarising microscopy, the lyotropism was investigated by small angle X-ray diffraction and by the contact preparation method, and the gel to liquid crystalline phase transition by FT-IR-spectroscopy. The compounds displayed thermotropic Smectic A (SmA), cubic and columnar phases, whereas in the lyotropic phase diagram lamellar, hexagonal and cubic phases are found. The introduction of unsaturated or methyl branched chains leads to liquid crystallinity at ambient temperature. The difference between the 1,3-oleyl-glycerol maltoside and the corresponding 1,2-oleoyl-glycerol maltoside is small.     

Observation of inverted cubic phase in hydrated dioleoylphosphatidylethanolamine membranes

We report the observation of an inverted cubic phase in aqueous dispersions of 1,2-dioleoyl-sn-glycero-3-phosphoethanolamine (DOPE) by small-angle X-ray diffraction. DOPE is a paradigm in the study of nonlamellar phases in biological systems: it exhibits a well-known phase transition from the lamellar (L alpha) to the inverted hexagonal phase (HII) as the temperature is raised. The transition is observed to occur rapidly when a DOPE dispersion is heated from 2 degrees C, where the L alpha phase is stable, to 15 degrees C, where the HII phase is stable. We report on the induction of a crystallographically well-defined cubic lattice that is slowly formed when the lipid dispersion is rapidly cycled between -5 and 15 degrees C hundreds of times. Once formed, the cubic lattice is stable at 4 degrees C for several weeks and exhibits the same remarkable metastability that characterizes other cubic phases in lipid-water systems. X-ray diffraction indicates that the cubic lattice is most consistent with either the Pn3m or Pn3 space group. Tests of lipid purity after induction of the cubic indicate the lipid is at least 98% pure. The cubic lattice can be destroyed and the system reset by cycling the specimen several times between -30 and 2 degrees C. The kinetics of the formation of the cubic are dependent on the thermal history of the sample, overall water concentration, and the extreme temperatures of the cycle.(ABSTRACT TRUNCATED AT 250 WORDS)     

Structural,dynamic and mechanical properties of POPC at low cholesterol concentration studied in pressure/temperature space

We have studied the structural, dynamic and mechanical properties of 1-palmitoyl-2-oleoyl- sn-glycero-3-phosphatidylcholine (POPC)/cholesterol binary mixtures by small-angle X-ray scattering. Our investigations were concentrated on the biologically most relevant pressure-temperature-cholesterol regime, i.e. the liquid crystalline phase and its phase boundary to the lamellar gel phase within a cholesterol concentration up to 25 mol%. From the dependence of the transition pressure we derived a value of 19 kJ/mol for the transition enthalpy Delta H(m) of POPC in excess water. With increasing cholesterol concentration, Delta H(m) drops to about 7 kJ/mol at 20 mol% cholesterol. Time-resolved pressure-scan (p-scan) and temperature-jump (T-jump) experiments reveal that at low cholesterol content (<5-8 mol%) the fluidity and also the bilayer compressibility increase remarkably. In contrast, at concentrations between 5 and 25 mol% cholesterol the bilayer becomes again more rigid and the lipid bilayer spacing increases about 2 A. Theses changes are attributed to the onset of phase separation between liquid disordered and liquid ordered phases. The fluid-fluid miscibility gap for this mono-unsaturated lecithin species is strongly enlarged compared with saturated lecithins.     

Interactions of cyclic AMP and its dibutyryl analogue with model membrane: X-ray diffraction and Raman spectroscopic study using cubic liquid-crystalline phases of monoolein

Interactions of adenosine 3':5'-cyclic monophosphate (cAMP) and its dibutyryl analogue, N6,2'-O-dibutyryladenosine 3':5'-cyclic monophosphate (dbcAMP), with a lipid bilayer were studied by small-angle X-ray diffraction (SAXD) and Raman spectroscopy. The cubic Pn3m phase of monoolein (MO) served as a bilayer-based model system. SAXD measurements have indicated that incorporation of approximately 3 wt.% cAMP leaves the phase parameters practically unaltered, whereas the same content of dbcAMP induces the intercubic Pn3m-->Ia3d transition. By applying the concepts of lipid shape parameter and infinite periodic minimal surface to these MO phases, we have suggested that, as opposed to cAMP, dbcAMP associates with the MO bilayer. This conclusion has been supported by the different effects of phase matrix on the Raman shifts of the adenine and phosphate vibrational modes of these two nucleotides. Moreover, Raman spectra have indicated that dbcAMP inserts into the bilayer through the butyryladenine group, positioning dbcAMP preferentially at the polar/apolar interface.     

Phase transition from a gel to a fluid phase of cubic symmetry in dimyristoylphosphatidylcholine/myristic acid (1:2, mol/mol) bilayers

Aqueous dispersions (pH 4.0) of a 2:1 (mol/mol) mixture of myristic acid with dimyristoylphosphatidylcholine undergo a sharp transition at 45-47 degrees C from a lamellar gel phase to a fluid phase which is optically isotropic. This fluid phase gives rise to 31P-NMR spectra, and 2H-NMR spectra of the chain-deuterated components, which are also isotropic. X-ray diffraction studies of the fluid phase at 49 degrees C, reveal reflections with spacings in the ratio square root of 2: (square root of 3): square root of 4: square root of 6: square root of 8, accompanied by a strong diffuse scatter. These reflections index on a cubic lattice of primitive space group Pn3 or Pn3m, or possibly the body-centered group Im3m, with a lattice constant of 21.2 nm. The dimensions of the phase are consistent with a structure composed of two systems of tetrahedrally (octahedrally) oriented inverted lipid cylinders, found for other cubic lipid phases with Pn3m (Im3m) symmetry. At higher temperatures the cubic phase gradually converts, with increasing temperature, to a coexisting inverted hexagonal phase.     

Glass transition behavior of octyl β-D-glucoside and octyl β-D-thioglucoside/water binary mixtures

The lyotropic behavior and glass-forming properties of octyl β-d-glucoside (C8Glu) and octyl β-d-thioglucoside (C8SGlu)/water binary mixtures were evaluated using differential scanning calorimetry (DSC) and polarizing optical microscopy (POM). The results clearly indicate that the mixture forms a glass in the supercooling state of liquid crystalline phases such as cubic, lamellar, and smectic. The glass transition temperature (T_g) of the mixture was strongly dependent on solute concentration, with a higher concentration correlating with a higher T_g. The experimental T_g was consistent with the predicted value calculated using the Couchman-Karasz equation in both the C8Glu and C8SGlu/water mixtures. The change of heat capacity at T_g showed the two bending points under variation of concentrations. And the highest temperature of phase transition from lamellar to isotropic solution was observed at around 50% molar concentration. It was expected that non-percolated state of water existed in extremely higher concentration ranges.     

A comparative study of the effects of dimethylsulfoxide and glycerol on the bicontinuous cubic structure of hydrated monoolein and its phase behavior

Both dimethylsulfoxide (DMSO) and glycerol act cryoprotectants for biological systems and materials. Knowledge of molecular interactions of DMSO and glycerol with biological lipids is important for understanding of their cryoprotecitive mechanisms. In this study, the phase behavior and structures of hydrated monoolein were investigated in the presence of DMSO or glycerol, using differential scanning calorimetry (DSC) and simultaneous X-ray diffraction/DSC measurements. Based on the results obtained by this study, partial phase diagrams were constructed as a function of DMSO or glycerol concentrations and temperature. DMSO and glycerol hardly affect the enthalpy value for melting temperature of lamellar crystal phase of monoolein and the structure. On the other hand, DMSO and glycerol greatly affect the phase transformations associated with bicontinuous cubic phases of monoolein and the cubic phase structures. DMSO expands Im3m/Pn3m cubic phase co-existence region in the phase diagram and increases the lattice constant of the Pn3m monoolein cubic phase. Glycerol shows opposite effects. The present study suggests that different mechanisms act in the cryopreservation by DMSO and glycerol.