Measurement of biodegradable substances using the salt-tolerant yeast Arxula adeninivorans for a microbial sensor immobilized with poly(carbamoyl)sulfonate (PCS). Part II: Application of the novel biosensor to real samples from coastal and island regions

A microbial sensor for rapid measurement of the amount of biodegradable substances based on the salt-tolerant yeast Arxula adeninivorans LS3 has been developed especially for coastal and island regions. Our parameter, the so-called sensorBOD, that is available after only a few minutes, agrees with the 5-day value for the biochemical oxygen demand (BOD5) very well. We have employed the Arxula sensor in the short-time estimation and supervision of the BOD of both domestic and industrial wastewater with high salinity. The novel sensor makes it possible to monitor the different types of wastewater rapidly without pretreatment, and it can be used for an active process control of sewage treatment works. Compared to a commercially available sensor, the novel sensor achieves better agreement between sensorBOD and BOD5 measurements with salt containing samples.     

Physiological characterization of a microbial sensor containing the yeast Arxula adeninivorans LS3

The yeast Arxula adeninivorans LS3 is a suitable organism for use as part of a microbial sensor. In combination with an amperometric oxygen electrode the sensor offered a possibility for the physiological characterization of this yeast. About 300-400 measurements could be carried out with a single Arxula sensor. The microbial sensor was remarkably stable for over 35 days, when kept at 37 °C during the operation time and at room temperature overnight. The physiological characteristics of Arxula adeninivorans LS3 obtained with the sensor technique were identical to the data obtained with the conventional techniques. However, the sensor technique makes it additionally possible to quantify the physiological data. So the substrates ribose, citric acid, glycerol, oil and benzoate produced signals lower than 10% in comparison to the glucose signal. Fructose, xylose, sucrose, maltose, gentianose, glucosamine, glutamic acid, tryptophan, butyric acid, lauryl acid and propionic acid reached 10-70%, galactose, alanine, glycine, lysine and methionine signals were similar to the glucose signal whereas acetic acid, ethyl alcohol, capron acid, capryl acid and caproic acid reached the highest signals up to 434%.     

Amperometric determination of lactate with novel trienzyme/poly(carbamoyl) sulfonate hydrogel-based sensor

A novel trienzyme sensor for the amperometric determination of lactate was constructed by immobilizing salicylate hydroxylase (SHL, E.C. 1.14.13.1), l-lactate dehydrogenase (LDH, E.C. 1.1.1.27), and pyruvate oxidase (PyOD, E.C. 1.2.3.3) on a Clark-type oxygen electrode. The enzymes were entrapped by a poly(carbamoyl) sulfonate (PCS) hydrogel on a Teflon membrane. LDH catalyzes the specific dehydrogenation of lactate consuming NAD(+). SHL catalyzes the irreversible decarboxylation and the hydroxylation of salicylate in the presence of oxygen and NADH produced by LDH. PyOD decarboxylates pyruvate using oxygen and phosphate. SHL and PyOD force the equilibrium of dehydrogenation of lactate by LDH to the product side by consuming NADH and pyruvate, respectively. Dissolved oxygen acts as an essential material for both PyOD and SHL during their respective enzymatic reactions. Therefore, an amplified signal, caused by the consumptions of dissolved oxygen by the two enzymes, was observed in the measurement of lactate. Regeneration of cofactor was found in the trienzyme system. A Teflon membrane was used to fabricate the sensor in order to avoid interferences. The sensor has a fast response (2s) and short recovery times (2 min). The total test time for a measurement by using this lactate sensor (4 min) was faster than using a commercial lactate testing kit (up to 10 min). The sensor has a linear range between 10 and 400 microM lactate, with a detection limit of 4.3 microM. A good agreement (R2 = 0.9984) with a commercial lactate testing kit was obtained in beverage sample measurements.     

Production of interleukin-6 in Arxula adeninivorans, Hansenula polymorpha and Saccharomyces cerevisiae by applying the wide-range yeast vector (CoMed) system to simultaneous comparative assessment

A wide-range yeast vector (CoMed) system has been applied to the comparative assessment of three different yeast platforms for the production of human interleukin-6. A vector equipped with an rRNA gene targeting sequence and an Arxula adeninivorans-derived LEU2 gene was used for simultaneous transformation of auxotrophic A. adeninivorans, Hansenula polymorpha and Saccharomyces cerevisiae strains. IL6 was expressed under control of the strong constitutive A. adeninivorans-derived TEF1 promoter, which is functional in all yeast species analyzed so far. Secreted IL-6 was found to be correctly processed from an MFalpha1-IL6 precursor in A. adeninivorans only, whereas N-terminally truncated proteins were observed in H. polymorpha and S. cerevisiae.     

Photoinitiated cross-linking of the biodegradable polyester poly(propylene fumarate). Part I. Determination of network structure

In this work, we investigated the mechanism involved in the photoinitiated cross-linking of the polyester poly(propylene fumarate) (PPF) using the initiator bis(2,4,6-trimethylbenzoyl) phenylphosphine oxide (BAPO). It was hypothesized that BAPO has the ability to cross-link PPF into solid polymer networks, without the use of a cross-linking monomer, because two pairs of radicals, both involving a fast adding phosphinoyl radical, were formed upon UV irradiation of BAPO. Spectroscopic investigation first confirmed the addition of BAPO derived radicals to the PPF olefin. Investigations of fumarate conversion and bulk network properties were then undertaken, using the BAPO initiator and a monoacylphosphine oxide (MAPO) initiator which contains a single photolabile bond. Results show that a single BAPO phosphinoyl radical was primarily responsible for the formation of a highly cross-linked PPF network and the additional radical pair which may be formed does not dramatically alter fumarate conversion or bulk network properties. From these results, the network structure of BAPO initiated, photo-cross-linked PPF may be deduced. Finally, this study demonstrates a method for inferring cross-linked network structures by contrasting properties of bulk materials formed from similar cross-linking initiators.     

Synthesis and characterization of novel biodegradable poly(carbonate ester)s with photolabile protecting groups

Novel biodegradable poly(carbonate ester)s with photolabile protecting groups were synthesized by ring-opening copolymerization of L-lactide (LA) with 5-methyl-5-(2-nitro-benzoxycarbonyl)-1,3-dioxan-2-one (MNC) with diethyl zinc (Et2Zn) as catalyst. The poly(L-lactide-co-5-methyl-5-carboxyl-1,3-dioxan-2-one) (P(LA-co-MCC)) was obtained by UV irradiation of poly(L-lactide acid-co-5-methyl-5-(2-nitro-benzoxycarbonyl)-1,3-dioxan-2-one) (P(LA-co-MNC)) to remove the protective 2-nitrobenzyl group. The free carboxyl groups on the copolymers P(LA-co-MCC) were reacted with paclitaxel, a common antitumor drug. Gel permeation chromatography and NMR studies confirmed the copolymer structures and successful attachment of paclitaxel to the copolymer.     

Proton-NMR study of the interaction of trans-dichloro-diamine-platinum(II) with poly(I) and poly(I).poly(C)

The fixation of trans-(NH₃)₂Cl₂ Pt(II) to poly(I)·poly(C) at low r_b (< 0.05) leads to the formation of two complexed species. The major species (ca. 82% of bound platinum) involves coordination of platinum to a single hypoxanthine base, while the other species involves coordination of two hypoxanthine bases, which are either far apart on the same strand or on separate poly(I) strands, to the platinum. These same two species are found after reaction with poly(I), as are two other species throughout the entire r_b range studied (r_b = 0–0.30). The latter two species are assigned to trans-Pt bound to two bases on a poly(I) strand with (a) one or (b) two free bases between the two bound bases. These two species, (a) and (b), account for ca. 35% of the bound platinum, although the 1:1 species remains dominant (ca. 55%). These two additional species are observed at high r_b (>0.075) after reaction with poly(I)·poly(C) but as very minor species. They are formed by reaction with melted poly(I) loops. Also at high r_b, we have observed a shifted cytidine H⁵ resonance arising from interaction of trans-Pt with a melted loop of poly(C). Most probably, this arises from an intramolecular poly(I) to poly(C) crosslink. Results from the reaction of trans-Pt with poly(C) are presented for comparison.     

Synthesis and characterization of poly(L-glutamic acid) gadolinium chelate: a new biodegradable MRI contrast agent

Most currently evaluated macromolecular contrast agents for magnetic resonance imaging (MRI) are not biodegradable. The goal of this study is to synthesize and characterize poly(l-glutamic acid) (PG) gadolinium chelates as biodegradable blood-pool MRI contrast agents. Two PG chelates of gadolinium diethylenetriaminepentaacetic acid (Gd-DTPA) were synthesized through the use of difunctional and monofunctional DTPA precursors. The conjugates were characterized with regard to molecular weight and molecular weight distribution, gadolinium content, relaxivity, and degradability. Distributions of the polymeric MRI contrast agents in various organs were determined by intravenous injection of (111)In-labeled polymers into mice bearing murine breast tumors. MRI scans were performed at 1.5 T in mice after bolus injection of the polymeric chelates. PG-Hex-DTPA-Gd, obtained from aminohexyl-substituted PG and DTPA-dianhydride, was partially cross-linked and was undegradable in the presence of cathepsin B. On the other hand, PG-Bz-DTPA-Gd synthesized directly from PG and monofunctional p-aminobenzyl-DTPA(acetic acid-tert-butyl ester) was a linear polymer and was degradable. The relaxivities of the polymers at 1.5 T were 3-8 times as great as that of Gd-DTPA. Both polymers had high blood concentrations and were primarily accumulated in the kidney. However, PG-Bz-DTPA-Gd was gradually cleared from the body and had significantly less retention in the blood, the spleen, and the kidney. MRI with PG-Bz-DTPA-Gd in mice showed enhanced vascular contrast at up to 2 h after the contrast agent injection. The ability of PG-Bz-DTPA-Gd to be degraded and cleared from the body makes it a favorable macromolecular MRI contrast agent.     

Preparation of poly(L-lactide)-based microspheres having a cationic or anionic surface using biodegradable surfactants

Poly(L-lactide)-based microspheres having cationic or anionic surfaces were prepared using polydepsipeptide-block-poly(L-lactide)s as surfactants. Polydepsipeptide-block-poly(L-lactide)s having amino or carboxylic acid groups on their side chains were synthesized through anionic ring-opening polymerizations of L-lactide using the corresponding protected polydepsipeptides as macroinitiators and consequent deprotections. Since these amphiphilic copolymers consisting of hydrophobic segments and hydrophilic segments with amino or carboxylic acid groups could be converted to cationic or anionic block copolymers, they could act as surfactants preparing poly(L-lactide)-based microspheres by an oil-in-water emulsion method. The amount of ionic groups located on the surfaces of the obtained microspheres was found to increase with increasing the feed of charged polydepsipeptide-block-poly(L-lactide)s in the blend of poly(L-lactide) and block copolymers. The average diameters of the dried microspheres estimated by scanning electron microscopy were found to decrease with an increase in feed of block copolymers in polymer blends.     

Electrochemical detection of cardiac troponin I using a microchip with the surface-functionalized poly(dimethylsiloxane) channel

A sensitive and rapid electrochemical microchip fabricated by assembling a surface-functionalized poly(dimethylsiloxane) (PDMS) microchannel with an interdigitated array (IDA) gold electrode was developed for the detection of human cardiac troponin I (cTnI) in the early diagnosis of acute myocardial infarction. Anti-cTnI was immobilized onto the internal surface of the PDMS channel on which protein G layer had been generated by silanization. To reduce electrode fouling, a PDMS channel was assembled with an IDA chip after surface treatment. The detection experiments were performed with successive injection of cTnI, alkaline phosphatase (AP)-labeled anti-cTnI, and p-aminophenylphosphate. Then, cyclic voltammograms were obtained by the oxidation peak current proportionally to the concentration of enzymatic product, p-aminophenol. The optimal packing density of anti-cTnI on the surface of the PDMS channel was determined at the anti-cTnI concentration of 30 microg/ml for the highest electrochemical signal. These demonstrate that the proper orientation and best packing density of antibody as well as no electrode fouling contributed to the low detection limit (148 pg/ml) of cTnI within 8 min.     

Proton NMR study of the interaction of cis-dichloro-diamine-platinum(II) with poly(I) and poly(I)·poly(C)

The fixation of cis (NH₃)₂Cl₂Pt(II) to poly(I)·poly(C) leads to the formation of two complexed species. One involves coordination to a single base (accounting for about 70% of the total platinum bound over the r_b range 0.07–0.25) and the other to two bases which are not adjacent to each other but may be on the same strand and separated by a loop. Reaction of the platinum compound with poly(I) gives in addition to the above two species a minor one (about 15%, independent of r_b over the range 0.05–0.30) in which the platinum is bound to two adjacent bases. The availability of such coordination reduces the dominance of the 1:1 species, which, however, remains the major one (ca. 55%).     

Synthesis and characterization of poly(butylene succinate-co-butylene malate): a new biodegradable copolyester bearing hydroxyl pendant groups

A new biodegradable copolyester, poly(butylene succinate-co-butylene malate) P(BS-co-BM), has been preliminarily prepared with optically active centers and lateral hydroxyl functional groups via a four-step synthetic strategy. First, an optically active benzyl-protected dimethyl malate was synthesized from a starting material of (S)-dimethyl malate and purified with good yield. Then, copolyester poly(butylene succinate-co-benzyl-protected butylene malate), P(BS-co-BBM), was prepared through a skilled condensation copolymerization of the benzyl-protected dimethyl malate, dimethyl succinate, and 1,4-butanediol in the presence of titanium tetraisopropoxide as the catalyst. Finally, a Pd/C catalyzed hydrogenation was applied to eliminate the benzyl protection group in a mixed solution of THF and methanol; thus the target copolyester P(BS-co-BM) was attained. On the other hand, physical properties of the synthesized copolyesters were systematically characterized by means of nuclear magnetic resonance spectrometer, Fourier transformed infrared spectrometer, gel permeation chromatography, optical polarimeter, quantitative hydroxyl titration, and thermal analytical instruments. The experimental evidence demonstrated a successful construction of the product P(BS-co-BM) bearing lateral hydroxyl functional groups. It was also revealed that the lower BBM unit content was in the benzyl-protected optically active P(BS-co-BBM) copolyester, the higher melting point T(m), crystallinity, the broader molecular distribution, and the lower glass transition temperature T(g) would be detected, and these results can be accounted for the presence of bulky lateral benzyl moieties. In contrast, the deprotected product P(BS-co-55 mol % BM) showed a higher T(m), crystallinity and lower T(g) than its counterpart P(BS-co-55 mol % BBM). Interestingly, a thermal stability as high as that of the linear PBS was observed for P(BS-co-55 mol % BM) while a strong BBM unit content dependence of thermal stability was detected for the benzyl-protected copolyester P(BS-co-BBM)s. Therefore, these results may be beneficial for the new optically active P(BS-co-BM) bearing hydrophilic hydroxyl functional groups as a potential biomaterial.     

Study of the interaction of cis-dichloro-(1,2 diethyl-3-aminopyrrolidine)Pt(II) complex with poly(I), poly(C) and poly(I) x poly(C)

The interaction of cis-dichloro-(1,2 diethyl-3-aminopyrrolidine)platinum(II) (Ptpyrr) with the polynucleotides poly(I), poly(C) and poly(I) x poly(C) acids was studied by circular dichroism, molecular fluorescence and (1)H NMR spectroscopies. Multivariate Curve Resolution, a factor analysis method, was applied for the analysis and interpretation of spectroscopic data obtained in mole ratio and kinetics studies. This procedure allows the determination of the number of different interaction complexes present during the experiments and the resolution of both concentration profiles and pure spectra for all of them. Two different interaction complexes were observed at the experimental conditions studied. The first one, at low Ptpyrr:polynucleotide ratio (r(Ptpyrr:poly)) values, corresponds to the interaction of Ptpyrr with hypoxanthine bases in the poly(I) moiety. This interaction leads to the destabilization and dissociation of the double-stranded conformation. The second complex was observed at higher r(Ptpyrr:poly) values and corresponds to the interaction of Ptpyrr to cytosine bases in poly(C) moiety. The formation of both complexes showed that the interaction of Ptpyrr with hypoxanthine bases occurred at the first stages of the reaction and with cytosine bases at longer reaction times. The results obtained show the utility of the Multivariate Curve Resolution approach for the analysis of data obtained by monitoring spectroscopically the interaction equilibria of platinum compounds with nucleic acids.     

Synthesis, characterization, and in vitro degradation of a biodegradable photo-cross-linked film from liquid poly(epsilon-caprolactone-co-lactide-co-glycolide) diacrylate

There has been little study on the effect of composition or molecular weight on the biodegradation rate of photo-cross-linked biodegradable aliphatic polyesters though such information is important for tissue engineering scaffolds. We have synthesized a new series of photopolymerizable linear poly(epsilon-caprolactone-co-lactide-co-glycolide) diacrylates with different molecular weights (Mn = 1800, 4800, and 9300 Da) and compositions (20%, 40%, and 60% epsilon-CL) and studied their biodegradation rates. The resultant oligomers were amorphous and appeared as viscous liquids at room temperature. Liquid-to-solid polymerization was carried out by UV irradiation in the presence of a photoinitiator. The photocuring yield was high (greater than 95%), and the photo-cross-linked polymers were amorphous and rubbery. Mechanical measurements showed that the polymers can be stretchable or rigid; the high molecular weight/low epsilon-CL network has a strain of 176% and a modulus of 1.66 MPa while the low molecular weight/high epsilon-CL network has a strain of 21% and a modulus of 12.3 MPa. In a 10 week in vitro biodegradation study, the polymers exhibited a two-stage degradation behavior. In the first stage, the polymer weight and strain remained almost constant, but a linear decrease in the Young's modulus (E) and ultimate stress (sigma) were observed. Lower oligomer molecular weight or epsilon-CL content correlated with a faster decrease in Young's modulus. In the second stage, which began when the Young's modulus dropped below 1 MPa, there was rapid weight loss and strain increase. The lower the epsilon-CL content, the earlier the second stage happened. Low molecular weight and high epsilon-CL content correlated with a longer modulus half-life (time for the modulus to degrade to 50% of its initial value). The degradation results suggest principles that may be helpful in predicting the biodegradation behavior of similar polymeric cross-linked networks. Films formed from these new polymers have excellent biocompatibility with smooth muscle cells.     

Synthesis and characterization of poly(d,l-lactic acid) via enzymatic ring opening polymerization by using free and immobilized lipase

Abstract

Polylactic acid is an interesting biodegradable and bioabsorbable material, and is produced from lactic acid, either by the direct polycondensation of lactic acid or via the ring-opening polymerization (ROP) of lactide. A future target of it is to improve some of the polyester properties for specific biomedical applications. The biocatalytic ROP of lactide is attractive as a route to polymer synthesis due to its lack of toxic reactants, mild reaction requirements, and recyclability of immobilized enzyme. Therefore, the use of immobilized enzymes is also being investigated.

The aim of this work was to develop a methodology to synthesize high molecular weight polylactic acid via enzymatic ROP method using free enzyme and Candida antarctica lipase B (CALB) immobilized onto chitin and chitosan. The efficiency of the two approaches has been compared, with polymerization kinetics and resulting products fully characterized by FT-IR, NMR, DSC, XRD, and TGA analyses.     

Thermal stability of lactate dehydrogenase in the complex with the anion polyelectrolyte poly(styrene sulfonate)

The temperature stability of the cytoplasmic enzyme of the glycolysis of lactate dehydrogenase from a pig muscle (isoenzyme M4) in a complex with the anion polyelectrolyte poly(styrenesulfonate) has been investigated by the methods of adiabatic differential scanning microcalorimetry, the own protein fluorescence, and circular dichroism. Calorimetric investigations of complex of lactate dehydrogenase with poly(styrenesulphonate) in 50 mM phosphate buffer at pH 7.0 have shown that the temperature of the transition and enthalpy of lactate dehydrogenase thermal denaturation sharply decreases with growing weight ratio poly(styrenesulphonate)/lactate dehydrogenase, though at 20 degrees C the enzyme activity of lactate dehydrogenase remains unchanged for several hours irrespective of the addition of poly(styrenesulphonate). The addition of phosphate ions to the solution enhances the resistance of lactate dehydrogenase to both thermal denaturation and inactivation by polyelectrolyte. The data obtained are interpreted from the viewpoint of a special role of two anion-binding centers in intersubunits contacts of lactate dehydrogenase, which enhance its resistance to both thermal denaturation and destruction by polyelectrolyte.     

Suspension culture of anchorage-dependent animal cells using nanospheres of the biodegradable polymer, poly(lactic-co-glycolic acid)

A novel method was developed for suspension culture of anchorage-dependent animal cells using biodegradable polymer nanospheres. The addition of poly(lactic-co-glycolic acid) nanospheres (907 nm average diam.) to the culture of human embryonic kidney 293 cells in stirred suspension bioreactors promoted the aggregate formation and cell growth (4.4-fold versus 2.2-fold growth for 7 d), compared to culture without nanospheres. This method may be useful for the culture of various types of anchorage-dependent animal cells in large-scale suspension bioreactors.     

Synthesis and characterization of biodegradable cationic poly(propylene fumarate-co-ethylene glycol) copolymer hydrogels modified with agmatine for enhanced cell adhesion

We synthesized positively charged biodegradable hydrogels by cross-linking of agmatine-modified poly(ethylene glycol)-tethered fumarate (Agm-PEGF) and poly(propylene fumarate-co-ethylene glycol) (P(PF-co-EG)) to investigate the effect of the guanidino groups of the agmatine on hydrogel swelling behavior and smooth muscle cell adhesion to the hydrogels. The weight swelling ratio of these hydrogels at pH 7.0 increased from 279 +/- 4 to 306 +/- 7% as the initial Agm-PEGF content increased from 0 to 200 mg/g of P(PF-co-EG), respectively. The diffusional exponents, n, during the initial phase of water uptake were independent of the initial Agm-PEGF content and were determined to be 0.66 +/- 0.08, 0.71 +/- 0.07, and 0.60 +/- 0.05 for respective initial Agm-PEGF contents of 0, 100, and 200 mg/g. The heat of fusion of water present in the hydrogels increased from 214 +/- 11 to 254 +/- 4 J/g as the initial Agm-PEGF content increased from 0 to 200 mg/g. The number of adherent smooth muscle cells increased dose-dependently from 15 +/- 6 to 75 +/- 7% of the initial seeding density as the initial Agm-PEGF content increased from 0 to 200 mg/g. These results suggest that the incorporation of the guanidino groups of agmatine into P(PF-co-EG) hydrogels increases the hydrogel free water content and the total water content of the hydrogels and also enhances cell adhesion to the hydrogels.