Structure study of cellulose fibers wet-spun from environmentally friendly NaOH/urea aqueous solutions

In this study, structure changes of regenerated cellulose fibers wet-spun from a cotton linter pulp (degree of polymerization approximately 620) solution in an NaOH/urea solvent under different conditions were investigated by simultaneous synchrotron wide-angle X-ray diffraction (WAXD) and small-angle X-ray scattering (SAXS). WAXD results indicated that the increase in flow rate during spinning produced a better crystal orientation and a higher degree of crystallinity, whereas a 2-fold increase in draw ratio only affected the crystal orientation. When coagulated in a H2SO4/Na2SO4 aqueous solution at 15 degrees C, the regenerated fibers exhibited the highest crystallinity and a crystal orientation comparable to that of commercial rayon fibers by the viscose method. SAXS patterns exhibited a pair of meridional maxima in all regenerated cellulose fibers, indicating the existence of a lamellar structure. A fibrillar superstructure was observed only at higher flow rates (>20 m/min). The conformation of cellulose molecules in NaOH/urea aqueous solution was also investigated by static and dynamic light scattering. It was found that cellulose chains formed aggregates with a radius of gyration, Rg, of about 232 nm and an apparent hydrodynamic radius, Rh, of about 172 nm. The NaOH/urea solvent system is low-cost and environmentally friendly, which may offer an alternative route to replace more hazardous existing methods for the production of regenerated cellulose fibers.     

Homogeneous quaternization of cellulose in NaOH/urea aqueous solutions as gene carriers

Quaternized celluloses (QCs) were homogeneously synthesized by reacting cellulose with 3-chloro-2-hydroxypropyltrimethylammonium chloride (CHPTAC) in NaOH/urea aqueous solutions. The structure and solution properties of the QCs were characterized by using elemental analysis, FTIR, (13)C NMR, SEC-LLS, viscometer, and zeta-potential measurement. The results revealed that water-soluble QCs, with a degree of substitution (DS) value of 0.20-0.63, could be obtained by adjusting the molar ratio of CHPTAC to anhydroglucose unit (AGU) of cellulose and the reaction time. The QC solutions in water displayed a typical polyelectrolyte behavior, and the intrinsic viscosity ([eta]) value determined from the Fuoss-Strauss method increased with increasing DS value. Moreover, two QC samples (DS = 0.46 and 0.63) were selected and studied as gene carriers. The results of gel retardation assay suggested that QCs could condense DNA efficiently. QCs displayed relatively lower cytotoxicity as compared with PEI, and QC/DNA complexes exhibited effective transfection compared to the naked DNA in 293T cells. The quaternized cellulose derivatives prepared in NaOH/urea aqueous solutions could be considered as promising nonviral gene carriers.     

Transparent films based on PLA and montmorillonite with tunable oxygen barrier properties

Polylactide (PLA) is viewed as a potential material to replace synthetic plastics (e.g., poly(ethylene terephthalate) (PET)) in food packaging, and there have been a number of developments in this direction. However, for PLA to be competitive in more demanding uses such as the packaging of oxygen-sensitive foods, the oxygen permeability coefficient (OP) needs to be reduced by a factor of ~10. To achieve this, a layer-by-layer (Lbl) approach was used to assemble alternating layers of montmorillonite clay and chitosan on extruded PLA film surfaces. When 70 bilayers were applied, the OP was reduced by 99 and 96%, respectively, at 20 and 50% RH. These are, to our knowledge, the best improvements in oxygen barrier properties ever reported for a PLA/clay-based film. The process of assembling such multilayer structures was characterized using a quartz crystal microbalance with dissipation monitoring. Transmission electron microscopy revealed a well-ordered laminar structure in the deposited multilayer coatings, and light transmittance results demonstrated the high optical clarity of the coated PLA films.     

Direct dissolution of cellulose in NaOH/thiourea/urea aqueous solution

Untreated cellulose was directly and quickly dissolved in NaOH/thiourea/urea aqueous solution. The mechanism of dissolution was investigated by SEM, WXRD and (13)C NMR. The components of this solvent cannot dissolve cellulose on their own, and the interactions between NaOH and urea, as well as between NaOH and thiourea, play an important role in improving the dissolution of cellulose. Moreover, (13)C NMR spectra proved that NaOH, thiourea, and urea were bound to cellulose molecules, which brings cellulose molecules into aqueous solution to a certain extent and prevents cellulose macromolecules from associating. (13)C NMR spectra of the cellulose solution show that this novel mixture is a direct solvent. Optical microscopy and CP MAS (13)C NMR were used to study the process of dissolution. The results reveal that cellulose is dissolved completely and that cellulose I (cotton linter) first changes to amorphous cellulose chains in solution, and then to cellulose II during regeneration. Moreover, a new, more effective dissolution method is proposed, as confirmed by dynamic rheology measurements.     

Solution properties of the acrylamide-modified cellulose polyelectrolytes in aqueous solutions

A novel cellulose-based polyelectrolyte (AM-C) containing acylamino (DS = 0.625) and carboxyl (DS = 0.148) groups was homogeneously synthesized from cellulose with acrylamide in NaOH/urea aqueous solutions. Solution properties of AM-C in aqueous solutions were investigated by laser light scattering, rheometry, and viscometry. The results indicated that AM-C could form large aggregates spontaneously in water with or without the addition of salts by the strong hydrogen bonds and electrostatic interaction between acylamino and carboxyl groups. Steady-shear flow study showed a Newtonian behavior of the solutions in the dilute regime while a shear-thinning behavior as the concentration increases. The critical concentration (c_e) for transition from dilute to concentrated solution was determined to be 0.7 wt %. Aqueous solutions of AM-C displayed good thermo-stability, reversible liquid-like characters attributing to the chemical modification. The derivation from Cox-Merz rule at relatively low concentration was related to the co-existence of single chain and large aggregates of AM-C in dilute regime. As the polymer concentration increased, the AM-C system was transformed into a homogeneous entanglement structure, resulting in the disappearance of deviations from the Cox-Merz rule.     

Favorable chitosan/cellulose film combinations for copper removal from aqueous solutions

Three well-formed film combinations of chitosan, in the beta form and cellulose acetate biopolymer, having different proportions, have been synthesized and characterized by X-ray diffraction and infrared spectroscopy. The film having a 1.0/0.50 proportion presented 6.87 mmol of nitrogen atoms per gram of synthesized hybrid, with the highest affinity for adsorbing copper from aqueous solutions at 298+/-1K. The isotherm obtained in this adsorption showed a saturation plateau that corresponds to 1.92 mmol of copper per gram of hybrid. The energetic effects caused by copper ion interaction were determined through calorimetric titration at the solid-liquid interface in aqueous solution and gave a net thermal effect that enabled the calculation of the exothermic enthalpic values and the equilibrium constant. The complete thermodynamic data showed that the system is favored by exothermic enthalpies, negative Gibbs free energies and positive entropies.     

Unique gelation behavior of cellulose in NaOH/urea aqueous solution

A transparent cellulose solution was prepared by mixing 7 wt % NaOH with 12 wt % urea aqueous solution which was precooled to below -10 degrees C and which was able to rapidly dissolve cellulose at ambient temperature. The rheological properties and behavior of the gel-formed cellulose solution were investigated by using dynamic viscoelastic measurement. The effects of temperature, time, cellulose molecular weight, and concentrations on both the shear storage modulus (G') and the loss modulus (G") were analyzed. The cellulose solution having a viscosity-average molecular weight (M(eta)) of 11.4 x 10(4) had its sol-gel transition temperature decreased from 60.3 to 30.5 degrees C with an increase of its concentration from 3 to 5 wt %. The gelation temperature of a 4 wt % cellulose solution dropped from 59.4 to 30.5 degrees C as the M(eta) value was increased from 4.5 x 10(4) to 11.4 x 10(4). Interestingly, at either higher temperature (above 30 degrees C), or lower temperature (below -3 degrees C), or for longer gelation time, gels could form in the cellulose solutions. However, the cellulose solution remains a liquid state for a long time at the temperature range from 0 to 5 degrees C. For the first time, we revealed an irreversible gelation in the cellulose solution system. The gel having been formed did not dissolve even when cooled to the temperature of -10 degrees C, at which it was dissolved previously. Therefore, this indicates that either heating or cooling treatment could not break such stable gels. A high apparent activation energy (E(a)) of the cellulose solution below 0 degrees C was obtained and was used to explain the gel formation under the cooling process.     

Mechanical and barrier properties of nanocrystalline cellulose reinforced chitosan based nanocomposite films

Nanocrystalline cellulose (NCC) reinforced chitosan-based biodegradable films were prepared by solution casting. The NCC content in the films was varied from 1 to 10% (dry wt. basis). It was found that the tensile strength (TS) of the nanocomposite films with 5% (w/w) NCC content was optimum with an improvement of 26% compared to the control chitosan films. Incorporation of NCC also significantly improved barrier properties. Water vapor permeability (WVP) of the chitosan/NCC films was decreased by 27% for the optimum 5% (w/w) NCC content. Swelling studies revealed a decrease in water uptake of the NCC-reinforced chitosan films. Analyses of thermal properties showed no significant effect of NCC whereas X-ray diffraction studies confirmed the appearance of crystalline peaks in the nanocomposite films. Surface morphology of the films was investigated by scanning electron microscopy and it was found that NCC was dispersed homogenously into chitosan matrix.     

Hydrogels of N-acylchitosans and their cellulose composites generated from the aqueous alkaline solutions

Hydrogels of N-acetyl and N-propionylchitosans were prepared form aqueous solutions of sodium N-acylchitosan salts (alkaline N-acylchitosans) and sodium N-acylchitosan xanthate [O-(sodium thio)thiocarbonyl N-acylchitosan], respectively, by standing at room temperature and on heating. Novel hydrogels of N-acetylchitosan-cellulose and N-propionylchitosan-cellulose composites were also prepared from sodium cellulose xanthate [O-(sodiumthio)thiocarbonyl cellulose] solutions mixed with sodium N-acylchitosan salts and with sodium N-acylchitosan xanthates, respectively.     

Aerocellulose: new highly porous cellulose prepared from cellulose-NaOH aqueous solutions

New highly porous pure cellulose aerogel-like material called "aerocellulose" was prepared from aqueous cellulose/NaOH solutions. Solutions were gelled to obtain shaped three-dimensional objects, then cellulose was regenerated and dried in supercritical conditions using CO2. The porosity of aerocellulose is higher than 95% with pore sizes distribution from a few tens of nanometers to a few tens of micrometers. The internal specific surface area is around 200-300 m2/g, and density ranges from 0.06 to 0.3 g/cm3, depending on the preparation conditions. The influence of cellulose DP and concentration, of the addition of a surfactant leading to solution foaming, of gelation conditions and the temperature and acidity of regenerating bath on the morphology of aerocellulose has been studied. The results are compared with another type of aerocellulose that was prepared from cellulose/NMMO solutions.     

Structure and properties of hydroxyapatite/cellulose nanocomposite films

The aim of this study was to develop a new inorganic-organic hybrid film. Nanohydroxyapaptite (nHAP) particles as the inorganic phase was mixed with cellulose in 7 wt.% NaOH/12 wt.% urea aqueous solution with cooling to prepare a blend solution, and then inorganic-organic hybrid films were fabricated by coagulating with Na₂SO₄ aqueous solution. The structure and properties of the hybrid films were characterized by high resolution transmitting electron microscopy (HRTEM), field emission scanning electron microscopy (FESEM), thermo-gravimetric analysis (TGA), Fourier transform infra-red (FT-IR) spectra, wide angle X-ray diffraction (WAXD) and tensile testing. The results revealed that the HAP nanoparticles with mean diameter of about 30 nm were uniformly dispersed and well immobilized in the hybrid film as a result of the role of the nano-and micropores in the cellulose substrate. A strong interaction existed between HAP and cellulose matrix, and their thermal stability and mechanical strength were improved as a result of good miscibility. Furthermore, the results of 293T cell viability assay indicated that the HAP/cellulose films had excellent biocompatibility and safety, showing potential applications in biomaterials.     

Preparation of nickel particles in hydrated cellulose matrix activated with alkali solutions

Materials containing micro- and nanodisperse nickel particles in hydrated cellulose film have been obtained by diffusion reduction. The effect of various NaOH concentrations on the film structure, functional composition, and morphology; nickel ion reduction; and nanocomposite material formation has been studied by Fourier transform infrared spectrometry, wide-angle X-ray scattering, and scanning electron microscopy. Nickel content in the samples varies from 1.1 to 21.3% wt %.     

SANS/SAXS study of the BSA solvation properties in aqueous urea solutions via a global fit approach

We report on the solvation properties and intermolecular interactions of a model protein (bovine serum albumine, BSA) in urea aqueous solutions, as obtained by combining small-angle neutron and X-ray scattering experiments. According to a global fit strategy, all the whole set of scattering curves are analysed by considering a unique model which includes the BSA structure, the protein-protein interactions and the thermodynamic exchange process of water/urea molecules at the protein solvent interface. As a main result, the equilibrium constant that accounts for the difference in composition between the bulk solvent and the protein solvation layer is derived. Results confirm that urea preferentially sticks to the protein surface, inducing a noticeable change in both the repulsive and the attractive interaction potentials.     

Biocomposite films prepared from ionic liquid solutions of chitosan and cellulose

Blends of chitosan and cellulose were successfully produced using 1-butyl-3-methylimidazolium acetate (BMIMAc) as solvent media. Films were prepared from the blends by manually spreading the solution on a flat surface and precipitating the polymers in a mixture of methanol and water. To prevent the shrinkage of films, most of the absorbed water was removed by freeze drying under vacuum. Films prepared from the polymeric solutions were investigated by means of FT-IR, TGA, X-ray diffraction and SEM measurements. The shifting of the bands corresponding to -NH and CO groups of chitosan (FT-IR), the absence of the diffraction peaks at 2θ = 10.7 and 14.9° (XRD), the increased E_a for thermal decomposition for all the polymeric blends (MTGA), and the presence of an apparent homogeneous structure with no phase separation of the two polymers (SEM) provide evidence for the miscibility between chitosan and cellulose in the solid state.     

Effect of temperature on viscosity properties of some alpha-amino acids in aqueous urea solutions

Viscosities for solutions of glycine, DL-alpha-alanine, DL-alpha-amino-n-butyric acid, DL-valine, DL-leucine and L-serine in 5 mol kg(-1) aqueous urea have been determined at 278.15, 288.15, 298.15 and 308.15 K. The viscosity B-coefficients for the amino acids in the aqueous urea solution have been calculated at different temperatures. The effect of temperature on the B-coefficients is discussed on the basis of the Feakins equation. The contribution of solute to the activation parameters (delta mu0*2, deltaH0*2, deltaS0*2) for viscous flow of the solution have been calculated, together with the Gibbs energy, enthalpy and entropy of transfer for the amino acids from the ground-state solvent to the hypothetical viscous transition state solvent. The contributions of the charged end group (NH3+, COO-) and CH2 groups of the amino acids to B-coefficient and delta mu0*2 have been also estimated using the linear correlations between B-coefficient or delta mu0*2 and the number of carbon atoms in the alkyl chains of the amino acids. All the activation parameters are discussed in terms of the solute-solvent interactions in the ground and transition states.     

Vibrational circular dichroism of carbohydrate films formed from aqueous solutions

Vibrational circular dichroism (VCD) spectra in the entire 2000-900 cm(-1) region have been recorded, for the first time, for films of carbohydrates prepared from aqueous solutions. Eight different carbohydrates, alpha-D-glucopyranosyl-(1-->4)-D-glucose, cyclomaltohexaose, alpha-D-glucopyranosyl alpha-D-glucopyranoside, beta-D-glucopyranosyl-(1-->6)-D-glucose, beta-D-glucopyranosyl-(1-->4)-D-glucose, D-glucose, and both enantiomers of 6-deoxygalactose and of allose, were investigated. The VCD spectra obtained for films are found to be identical to the corresponding spectra obtained for aqueous solutions of carbohydrates. These measurements demonstrate several advantages of significant importance. The strong infrared absorption of water has prevented, in the past, the pursuit for routine applications of VCD in determining the structures of carbohydrates in aqueous solutions. This limitation is not present for film studies because water solvent is removed in the process of preparing the films. Also, strong infrared absorption of water at 1650 cm(-1) requires the use of very short-pathlength (6 microm) cells for measurements on aqueous solutions. This requirement and concomitant inconveniences (such as laborious assembling of a demountable liquid cell or purchasing an expensive variable pathlength liquid cell) have been eliminated for film measurements. The removal of interfering water absorption in film studies resulted in higher light throughput and better signal-to-noise ratios for VCD measurements. Another point of significance is that the amount of carbohydrate sample required for VCD measurements on films is approximately one to two orders of magnitude smaller than that required for corresponding VCD measurements on aqueous solutions. Since carbohydrate samples can now be studied as films, VCD spectroscopy becomes much more broadly applicable for carbohydrates than previously believed. The present work, in combination with other film measurements in our laboratory, indicate that VCD studies on films can be used more generally, providing a convenient and powerful approach for probing structural information for biologically important compounds.     

Microstructure and aggregation behavior of methylcelluloses prepared in NaOH/urea aqueous solutions

Three water-soluble methylcelluloses (MCs) were prepared through homogeneous reaction in NaOH/urea aqueous solution, using dimethyl sulfate as a methylation reagent. The microstructure of the MC samples was characterized by IR, GC/MS, NMR, while dilute solution properties were measured by SEC–LLS, DLS and viscometer. The total degrees of substitution (DS) of the MC samples were 1.09, 1.42 and 1.56, respectively. However, we found that the relative DS value varies with the position of the hydroxyl group, i.e., C-2 > C-3 ≈ C-6, indicating the difference of reaction activity of different hydroxyl groups. In aqueous solution, MC has a trendency to form aggregates and hard to form actual solution, even at low concentration and low temperature, which was confirmed by the SEC–LLS and DLS result that isolated MC chains and large aggregates coexisted in the dilute aqueous solution. MC aqueous solutions showed two-stage temperature dependence of hydrodynamic radius. In the first stage, i.e., the temperature ranges from 20 to 65 °C, the hydrodynamic radius of MC displayed bimodal distribution, corresponding to the single chains and large aggregates. While in the second stage, i.e., the temperature higher than 70 °C, only large aggregates appeared. The results also proved that the microstructure of MC had a great influence on its physical properties.     

Supermolecular structure of cellulose/amylose blends prepared from aqueous NaOH solutions and effects of amylose on structural formation of cellulose from its solution

We previously proposed a mechanism for the structural formation of cellulose from its solution using a molecular dynamics (MD) simulation and suggested that the initial structure from its solution plays a critical role in determining its final structure. Structural changes in the van der Waals-associated cellulose molecular sheet as the initial structure were examined by MD simulation; the molecular sheet was found to be disordered due to maltohexaoses as an amylose model in terms of the hydrogen bonding system of cellulose. The structure and properties of cellulose/amylose blends prepared from an aqueous NaOH solution were examined experimentally by wide-angle X-ray diffraction and dynamic viscoelasticity measurements. The crystallinity of cellulose in the cellulose/amylose blend films was lower than that of cellulose film. The diffraction peaks of the cellulose/amylose blends were slightly shifted; specifically, () was shifted to a higher angle, and (1 1 0) and (0 2 0) were shifted to lower angles. These experimental results probably resulted from the disordered molecular sheet, as revealed by MD simulations.     

The structural properties of magainin in water, TFE/water, and aqueous urea solutions: molecular dynamics simulations

Here, the MD simulations and comparative structural analysis of Magainin in water, TFE/water, and 2M, 4M, and BM urea solutions is reported. For MAG-TFE/water and MAG-2M urea the largely alpha helical conformation of the peptide is maintained throughout the 9-ns simulation. While in water, 4M urea, and 8M urea, the helix length decreases and at the same time helix radius increases. This suggests a more destabilized magainin secondary structure. Our simulation data reveals that the stabilizing effect of TFE is induced by preferential accumulation of TFE molecules around the alpha helical peptide. These results indicate that an aqueous urea solution solvates the surface of polypeptide chain more favorably than pure water. Urea molecules interact more favorably with nonpolar groups of the peptide in comparison with water, and the presence of urea improves the interactions of water molecules with the hydrophilic groups of the peptide. At 8M urea, there are more direct interactions between the urea and solute, and the helix is destabilized. At 2M urea, the interaction of urea molecules and nonpolar residues are weak, therefore, the presence of urea molecules decreases the interactions of water molecules with hydrophilic groups. Urea could not deteriorate the peptide secondary structure with time from an initial helix structure.