Techno-economic implications of improved high gravity corn mash fermentation

The performance of Saccharomyces cerevisiae MBG3964, a strain able to tolerate >18% v/v ethanol, was compared to leading industrial ethanol strain, Fermentis Ethanol Red, under high gravity corn mash fermentation conditions. Compared to the industrial ethanol strain, MBG3964 gave increased alcohol yield (140 g L⁻¹ vs. 126 g L⁻¹), lower residual sugar (4 g L⁻¹ vs. 32 g L⁻¹), and lower glycerol (11 g L⁻¹ vs. 12 g L⁻¹). After 72 h fermentation, MBG3964 showed about 40% viability, whereas the control yeast was only about 3% viable. Based on modelling, the higher ethanol tolerant yeast could increase the profitability of a corn-ethanol plant and help it remain viable through higher production, lower unit heating requirements and extra throughput. A typical 50 M gal y⁻¹ dry mill ethanol plant that sells dried distiller’s grain could potentially increase its profit by nearly $US3.4 M y⁻¹ due solely to the extra yield, and potentially another $US4.1 M y⁻¹ if extra throughput is possible.     

Bioethanol fermentation of concentrated rice straw hydrolysate using co-culture of Saccharomyces cerevisiae and Pichia stipitis

Rice straw is one of the abundant lignocellulosic feed stocks in the world and has been selected for producing ethanol at an economically feasible manner. It contains a mixture of sugars (hexoses and pentoses).Biphasic acid hydrolysis was carried out with sulphuric acid using rice straw. After acid hydrolysis, the sugars, furans and phenolics were estimated. The initial concentration of sugar was found to be 16.8 g L⁻¹. However to increase the ethanol yield, the initial sugar concentration of the hydrolysate was concentrated to 31 g L⁻¹ by vacuum distillation. The concentration of sugars, phenols and furans was checked and later detoxified by over liming to use for ethanol fermentation. Ethanol concentration was found to be 12 g L⁻¹, with a yield, volumetric ethanol productivity and fermentation efficiency of 0.33 g L⁻¹ h⁻¹, 0.4 g g⁻¹ and 95%, respectively by co-culture of OVB 11 (Saccharomyces cerevisiae) and Pichia stipitis NCIM 3498.     

3-Phenyllactic acid production by substrate feeding and pH-control in fed-batch fermentation of Lactobacillus sp. SK007

3-Phenyllactic acid (PLA), which is produced by some strains of lactic acid bacteria (LAB), is a known antimicrobial agent with a broad spectrum. Batch and fed-batch fermentation by the strain Lactobacillus sp. SK007 for PLA production have been reported. With batch fermentation without pH-control, PLA production yield was 2.42 g L⁻¹. When fed-batch fermentation by Lactobacillus sp. SK007 was conducted in 3 L initial volume with pH-control at 6.0 and intermittent feeding, which was developed after fermentation for 12 h and every 2 h with 120 mL 100 g L⁻¹ PPA phenylpyruvic acid (PPA) and 50 mL 500 g L⁻¹ glucose each time, PLA production yield reached 17.38 g L⁻¹. The final conversion ratio of PPA to PLA was 51.1%, and the PLA production rate was 0.241 g L⁻¹ h⁻¹. This indicated that PPA was the ideal substrate for PLA fermentation production, and fed-batch fermentation with intermittent PPA feeding and pH-control was an effective approach to improve PLA production yield.     

Ethanol production from syngas by Clostridium strain P11 using corn steep liquor as a nutrient replacement to yeast extract

The feasibility of replacing yeast extract (YE) by corn steep liquor (CSL), a low cost nutrient source, for syngas fermentation to produce ethanol using Clostridium strain P11 was investigated. About 32% more ethanol (1.7 g L⁻¹) was produced with 20 g L⁻¹ CSL media in 250-mL bottle fermentations compared to media with 1 g L⁻¹ YE after 360 h. Maximum ethanol concentrations after 360 h of fermentation in a 7.5-L fermentor with 10 and 20 g L⁻¹ CSL media were 8.6 and 9.6 g L⁻¹, respectively, which represent 57% and 60% of the theoretical ethanol yields from CO. Only about 6.1 g L⁻¹ of ethanol was obtained in the medium with 1 g L⁻¹ YE after 360 h, which represents 53% of the theoretical ethanol yield from CO. The use of CSL also enhanced butanol production by sevenfold compared to YE in bottle fermentations. These results demonstrate that CSL can replace YE as the primary medium component and significantly enhance ethanol production by Clostridium strain P11.     

Effect of lignocellulosic inhibitory compounds on growth and ethanol fermentation of newly-isolated thermotolerant Issatchenkia orientalis

A newly isolated thermotolerant ethanologenic yeast strain, Issatchenkia orientalis IPE 100, was able to produce ethanol with a theoretical yield of 85% per g of glucose at 42 °C. Ethanol production was inhibited by furfural, hydroxymethylfurfural and vanillin concentrations above 5.56 g L⁻¹, 7.81 g L⁻¹, and 3.17 g L⁻¹, respectively, but the strain was able to produce ethanol from enzymatically hydrolyzed steam-exploded cornstalk with 93.8% of theoretical yield and 0.91 g L⁻¹ h⁻¹ of productivity at 42 °C. Therefore, I. orientalis IPE 100 is a potential candidate for commercial lignocelluloses-to-ethanol production.     

Cultivation of microalgae for oil production with a cultivation strategy of urea limitation

The microalgae, Chlorella sp., were cultivated in various culture modes to assess biomass and lipid productivity in this study. In the batch mode, the biomass concentrations and lipid content of Chlorella sp. cultivated in a medium containing 0.025–0.200 g L⁻¹ urea were 0.464–2.027 g L⁻¹ and 0.661–0.326 g g⁻¹, respectively. The maximum lipid productivity of 0.124 g d⁻¹ L⁻¹ occurred in a medium containing 0.100 g L⁻¹ urea. In the fed-batch cultivation, the highest lipid content was obtained by feeding 0.025 g L⁻¹ of urea during the stationary phase, but the lipid productivity was not significantly increased. However, a semi-continuous process was carried out by harvesting the culture and renewing urea at 0.025 g L⁻¹ each time when the cultivation achieved the early stationary phase. The maximum lipid productivity of 0.139 g d⁻¹ L⁻¹ in the semi-continuous culture was highest in comparison with those in the batch and fed-batch cultivations.     

Biological treatment of eucalypt spent sulphite liquors: a way to boost the production of second generation bioethanol

The fermentation of reducing sugars from hardwood (eucalypt) spent sulphite liquor (HSSL) into ethanol by Pichia (Scheffersomyces) stipitis is hindered by concomitant inhibitors of microbial metabolism. The conditions for the HSSL biological treatment step by Paecilomyces variotii were evaluated and optimised. Two different strategies of reactor operation were compared using single batch (B) and sequential batch reactor (SBR). Biological treatment of HSSL in the SBR revealed the best results with respect to the removal of microbial inhibitors. Also, most of inhibitory compounds, acetic acid, gallic acid, pyrogallol, amongst others, were removed from HSSL by P. variotii before the ethanol fermentation. The bio-detoxified HSSL was subjected to a successful fermentation by P. stipitis, attaining a maximum ethanol concentration of 2.4 g L⁻¹ with a yield of 0.24 g ethanol g sugars⁻¹.     

Effect of organic loading and retention time on dairy manure fermentation

The investigations presented and discussed herein establish an enhanced understanding on volatile fatty acid (VFA) production as a function of dairy manure fermenter organic loading (OL) and retention time (RT), first through a factorial of 64 fermentation potential (FP) batch tests, followed by analysis of a continuously operated pilot-scale fermenter. The maximum observed net FP - 0.103 mg VFA produced (as COD) (mg VS applied)⁻¹ - occurred at an OL of 40.7 g VS L⁻¹ and at a RT of 6 days. The pilot-scale fermenter exhibited an average yield of 0.09 mg VFA (as COD) synthesized (mg VS applied)⁻¹, with average effluent total VFA concentrations of 6398 mg VFA (as COD) L⁻¹. The research demonstrates that FP tests are an effective method to optimize continuously operated dairy manure fermenters, and that dairy manure fermentation can yield large quantities of organic acids at short RTs and high OL rates.     

Effect of nutrient limitation and two-stage continuous fermentor design on productivities during "Clostridium ragsdalei" syngas fermentation

The effect of three limiting nutrients, calcium pantothenate, vitamin B₁₂ and cobalt chloride (CoCl₂), on syngas fermentation using “Clostridium ragsdalei” was determined using serum bottle fermentation studies. Significant results from the bottle studies were translated into single- and two-stage continuous fermentor designs. Studies indicated that three-way interactions between the three limiting nutrients, and two-way interactions between vitamin B₁₂ and CoCl₂ had a significant positive effect on ethanol and acetic acid formation. In general, ethanol and acetic acid production ceased at the end of 9 days corresponding to the production of 2.01 and 1.95 g L⁻¹ for the above interactions. Reactor studies indicated the three-way nutrient limitation in two-stage fermentor showed improved acetic acid (17.51 g g⁻¹ cells) and ethanol (14.74 g g⁻¹ cells) yield compared to treatments in single-stage fermentors. These results further support the hypothesis that it is possible to modulate the product formation by limiting key nutrients during C. ragsdalei syngas fermentation.     

Modeling of biomass production by Spirulinaplatensis as function of phosphate concentrations and pH regimes

Batch cultivations were performed to evaluate the influence of phosphate concentrations (0.25, 0.5, 0.75, and 1.0 g L⁻¹) for pH regimes (9.5, 10.0, and 10.5) on the biomass production by Spirulina platensis. The best condition for cell growth (3.099 g L⁻¹) was found at 0.5 g L⁻¹ phosphate and pH value of 10.0. Cultivation time, phosphate, and pH caused to increase significantly (p < 0.01) in biomass production by S. platensis. Lag time was observed up to 4 h. After then, biomass production increased sharply (p < 0.01) from 0.020 g L⁻¹ to 2.063, 2.213, 1.532, and 0.797 g L⁻¹ at 0.25, 0.5, 0.75, and 1.0 g L⁻¹ phosphate values, respectively. Modified Gompertz model could be regarded as sufficient to describe the biomass production by S. platensis with high determination coefficients and low sum of square value indicated that. Biological parameters for biomass production were successfully predicted by modified Gompertz model.     

Enhanced ethanol production by fermentation of rice straw hydrolysate without detoxification using a newly adapted strain of Pichia stipitis

An enhanced inhibitor-tolerant strain of Pichia stipitis was successfully developed through adaptation to acid-treated rice straw hydrolysate. The ethanol production obtained by fermentation of NaOH-neutralized hydrolysate without detoxification using the adapted P. stipitis was comparable to fermentation of overliming-detoxified hydrolysate. The ethanol yield using the adapted P. stipitis with both types of hydrolysate at pH 5.0 achieved 0.45 g_p g_s⁻¹, which is equivalent to 87% of the maximum possible ethanol conversion. Furthermore, the newly adapted P. stipitis demonstrated significantly enhanced tolerance to sulfate and furfural despite the fact that both inhibitors had not been removed from the hydrolysate by NaOH neutralization. Finally, the ethanol conversion could be maintained at 60% and above when the neutralized hydrolysate contained 3.0% sulfate and 1.3 g L⁻¹ furfural.     

In silico optimization and low structured kinetic model of poly[(R)-3-hydroxybutyrate] synthesis by Cupriavidus necator DSM 545 by fed-batch cultivation on glycerol

Glycerol was utilized by Cupriavidus necator DSM 545 for production of poly-3-hydroxybutyrate (PHB) in fed-batch fermentation. Maximal specific growth rates (0.12 and 0.3 h⁻¹) and maximal specific non-growth PHB production rate (0.16 g g⁻¹ h⁻¹) were determined from two experiments (inocula from exponential and stationary phase). Saturation constants for nitrogen (0.107 and 0.016 g L⁻¹), glycerol (0.05 g L⁻¹), non-growth related PHB synthesis (0.011 g L⁻¹) and nitrogen/PHB related inhibition constant (0.405 g L⁻¹), were estimated. Five relations for specific growth rate were tested using mathematical models. In silico performed optimization procedures (varied glycerol/nitrogen ratio and feeding) has resulted in a PHB content of 70.9%, shorter cultivation time (23 h) and better PHB yield (0.347 g g⁻¹). Initial concentration of biomass 16.8 g L⁻¹ and glycerol concentration in broth between 3 and 5 g L⁻¹ were decisive factors for increasing of productivity.     

Butyric acid fermentation in a fibrous bed bioreactor with immobilized Clostridium tyrobutyricum from cane molasses

Butyrate fermentation by immobilized Clostridium tyrobutyricum was successfully carried out in a fibrous bed bioreactor using cane molasses. Batch fermentations were conducted to investigate the influence of pH on the metabolism of the strain, and the results showed that the fermentation gave a highest butyrate production of 26.2 g l⁻¹ with yield of 0.47 g g⁻¹ and reactor productivity up to 4.13 g l⁻¹ h⁻¹ at pH 6.0. When repeated-batch fermentation was carried out, long-term operation with high butyrate yield, volumetric productivity was achieved. Several cane molasses pretreatment techniques were investigated, and it was found that sulfuric acid treatment gave better results regarding butyrate concentration (34.6 ± 0.8 g l⁻¹), yield (0.58 ± 0.01 g g⁻¹), and sugar utilization (90.8 ± 0.9%). Also, fed-batch fermentation from cane molasses pretreated with sulfuric acid was performed to further increase the concentration of butyrate up to 55.2 g l⁻¹.     

Enhanced ethanol production from sugarcane juice by galactose adaptation of a newly isolated thermotolerant strain of Pichia kudriavzevii

The thermotolerant yeast strain isolated from sugarcane juice through enrichment technique was identified as a strain of Pichiakudriavzevii (Issatchenkiaorientalis) through molecular characterization. The P. kudriavzevii cells adapted to galactose medium produced about 30% more ethanol from sugarcane juice than the non-adapted cells. The recycled cells could be used for four successive cycles without a significant drop in ethanol production. Fermentation in a laboratory fermenter with galactose adapted P. kudriavzevii cells at 40 °C resulted in an ethanol concentration and productivity of 71.9 g L⁻¹ and 4.0 g L⁻¹ h⁻¹, respectively from sugarcane juice composed of about 14% (w/v) sucrose, 2% (w/v) glucose and 1% (w/v) fructose. In addition to ethanol, 3.30 g L⁻¹ arabitol and 4.19 g L⁻¹ glycerol were also produced, whereas sorbitol and xylitol were not formed during fermentation. Use of galactose adapted P. kudriavzevii cells for ethanol production from sugarcane juice holds potential for scale-up studies.     

Ethanol production from sweet sorghum juice using very high gravity technology: Effects of carbon and nitrogen supplementations

Ethanol production from sweet sorghum juice by Saccharomyces cerevisiae NP01 was investigated under very high gravity (VHG) fermentation and various carbon adjuncts and nitrogen sources. When sucrose was used as an adjunct, the sweet sorghum juice containing total sugar of 280 g l⁻¹, 3 g yeast extract l⁻¹ and 5 g peptone l⁻¹ gave the maximum ethanol production efficiency with concentration, productivity and yield of 120.68 ± 0.54 g l⁻¹, 2.01 ± 0.01 g l⁻¹ h⁻¹ and 0.51 ± 0.00 g g⁻¹, respectively. When sugarcane molasses was used as an adjunct, the juice under the same conditions gave the maximum ethanol concentration, productivity and yield with the values of 109.34 ± 0.78 g l⁻¹, 1.52 ± 0.01 g l⁻¹ h⁻¹ and 0.45 ± 0.01 g g⁻¹, respectively. In addition, ammonium sulphate was not suitable for use as a nitrogen supplement in the sweet sorghum juice for ethanol production since it caused the reduction in ethanol concentration and yield for approximately 14% when compared to those of the unsupplemented juices.     

An innovative consecutive batch fermentation process for very high gravity ethanol fermentation with self-flocculating yeast

An innovative consecutive batch fermentation process was developed for very high gravity (VHG) ethanol fermentation with the self-flocculating yeast under high biomass concentration conditions. On the one hand, the high biomass concentration significantly shortened the time required to complete the VHG fermentation and the duration of yeast cells suffering from strong ethanol inhibition, preventing them from losing viability and making them suitable for being repeatedly used in the process. On the other hand, the separation of yeast cells from the fermentation broth by sedimentation instead of centrifugation, making the process economically more competitive. The VHG medium composed of 255 g L⁻¹ glucose and 6.75 g L⁻¹ each of yeast extract and peptone was fed into the fermentation system for nine consecutive batch fermentations, which were completed within 8–14 h with an average ethanol concentration of 15% (v/v) and ethanol yield of 0.464, 90.8% of its theoretical value of 0.511. The average ethanol productivity that was calculated with the inclusion of the downstream time for the yeast flocs to settle from the fermentation broth and the supernatant to be removed from the fermentation system was 8.2 g L⁻¹ h⁻¹, much higher than those previously reported for VHG ethanol fermentation and regular ethanol fermentation with ethanol concentration around 12% (v/v) as well.     

Development of chemically defined media supporting high cell density growth of Ketogulonicigenium vulgare and Bacillus megaterium

The immediate precursor of L-ascorbic acid, or vitamin C, is 2-keto-l-gulonic acid (2-KLG). This is commonly produced commercially by Ketogulonicigenium vulgare and Bacillus megaterium, using corn steep liquor powder (CSLP) as an organic nitrogen source. In this study, the effects of the individual CSLP components (amino acids, vitamins, and metal elements) on 2-KLG production were evaluated, with the aim of developing a complete, chemically defined medium for 2-KLG production. Forty components of CSLP were analyzed, and key components were correlated to biomass, 2-KLG productivity, and consumption rate of L-sorbose. Glycine had the greatest effect, followed by serine, biotin, proline, nicotinic acid, and threonine. The combination of 0.28 g L⁻¹ serine, 0.36 g L⁻¹glycine, 0.18 g L⁻¹ threonine, 0.28 g L⁻¹proline, 0.19 g L⁻¹nicotinic acid, and 0.62 mg L⁻¹biotin in a chemically defined medium produced the highest maximum biomass concentration (4.2 × 10⁹ cfu mL⁻¹), 2-KLG concentration (58 g L⁻¹), and yield (0.76 g g⁻¹) after culturing for 28 h.     

Optimization of growth media for obtaining high-cell density cultures of halophilic archaea (family Halobacteriaceae) by response surface methodology

Optimization of media components for the growth and biomass production of Halobacterium salinarum VKMM 013 was carried out using response surface methodology. A second order quadratic model was estimated and media components were determined based on quadratic regression equation generated by model. These were 6.35 g L⁻¹ of KCl, 9.70 g L⁻¹ of MgSO₄, 13.38 g L⁻¹ of gelatin and 12.00 g L⁻¹ of soluble starch in nutrient broth supplemented with artificial seawater with 20% (w/v) of NaCl. In these optimal conditions, the obtained cell concentration of 0.746 g L⁻¹ dry weight was in agreement with the predicted cell concentration. The optimized media significantly shortened the time required for cell culture to reach the stationary phase while providing a nearly 2.4-fold increase in biomass production. Furthermore, in cell cultures of three other halophilic archaea the use of optimized media enhanced growth rate and provided high-cell density.     

Biomass production and nitrogen and phosphorus removal by the green alga Neochloris oleoabundans in simulated wastewater and secondary municipal wastewater effluent

Biomass productivity of 350 mg DCW L⁻¹ day⁻¹ with a final biomass concentration of 3.15 g DCW L⁻¹ was obtained with Neochloris oleoabundans grown in artificial wastewater at sodium nitrate and phosphate concentrations of 140 and 47 mg L⁻¹, respectively, with undetectable levels of residual N and P in effluents. In secondary municipal wastewater effluents enriched with 70 mg N L⁻¹, the alga achieved a final biomass concentration of 2.1 g DCW L⁻¹ and a biomass productivity of 233.3 mg DCW L⁻¹ day⁻¹. While N removal was very sensitive to N:P ratio, P removal was independent of N:P ratio in the tested range. These results indicate that N. oleoabundans could potentially be employed for combined biofuel production and wastewater treatment.     

Fed-batch fermentation for production of Kluyveromyces marxianusFII 510700 cultivated on a lactose-based medium

A strain of Kluyveromyces marxianus was grown in batch culture in lactose-based media at varying initial lactose concentrations (10–60 g L^–1) at 30°C, pH 5.0, dissolved oxygen concentrations greater than 20%. Increasing the concentration of mineral salts three-fold at 40 g L^–1 and 60 g L^–1 initial lactose concentration showed only a small increase in the yield of biomass, from 0.38 g g^–1 to 0.41 g g^–1, indicating that the initial batch cultures were not significantly nutrient- (mineral salts)-limited. A relatively high biomass concentration (105 g L^–1) was obtained in fed-batch culture following extended lactose feeding. An average specific growth rate (0.27 h^–1), biomass yield (0.38 g g^–1) and overall productivity (2.9 g L^–1 h^–1) were obtained for these fed-batch conditions. This fed-batch protocol provides a strategy for achieving relatively high concentrations and productivities of K. marxianus on other lactose-based substrate streams (e.g., whey) from the dairy industry.