Anaerobic treatment of a chemical synthesis-based pharmaceutical wastewater in a hybrid upflow anaerobic sludge blanket reactor

In this study, performance of a lab-scale hybrid up-flow anaerobic sludge blanket (UASB) reactor, treating a chemical synthesis-based pharmaceutical wastewater, was evaluated under different operating conditions. This study consisted of two experimental stages: first, acclimation to the pharmaceutical wastewater and second, determination of maximum loading capacity of the hybrid UASB reactor. Initially, the carbon source in the reactor feed came entirely from glucose, applied at an organic loading rate (OLR) 1 kg COD/m(3) d. The OLR was gradually step increased to 3 kg COD/m(3) d at which point the feed to the hybrid UASB reactor was progressively modified by introducing the pharmaceutical wastewater in blends with glucose, so that the wastewater contributed approximately 10%, 30%, 70%, and ultimately, 100% of the carbon (COD) to be treated. At the acclimation OLR of 3 kg COD/m(3) d the hydraulic retention time (HRT) was 2 days. During this period of feed modification, the COD removal efficiencies of the anaerobic reactor were 99%, 96%, 91% and 85%, and specific methanogenic activities (SMA) were measured as 240, 230, 205 and 231 ml CH(4)/g TVS d, respectively. Following the acclimation period, the hybrid UASB reactor was fed with 100% (w/v) pharmaceutical wastewater up to an OLR of 9 kg COD/m(3) d in order to determine the maximum loading capacity achievable before reactor failure. At this OLR, the COD removal efficiency was 28%, and the SMA was measured as 170 ml CH(4)/g TVS d. The hybrid UASB reactor was found to be far more effective at an OLR of 8 kg COD/m(3) d with a COD removal efficiency of 72%. At this point, SMA value was 200 ml CH(4)/g TVS d. It was concluded that the hybrid UASB reactor could be a suitable alternative for the treatment of chemical synthesis-based pharmaceutical wastewater.     

Treatment of fresh leachate with high-strength organics and calcium from municipal solid waste incineration plant using UASB reactor

Treatment of a fresh leachate with high-strength organics and calcium from municipal solid waste (MSW) incineration plant by an up-flow anaerobic sludge blanket (UASB) reactor was investigated under mesophilic conditions, emphasizing the influence of organic loading rate (OLR). When the reactor was fed with the raw leachate (COD as high as 70,390-75,480 mg/L) at an OLR of 12.5 kg COD/(m³ d), up to ∼82.4% of COD was removed suggesting the feasibility of UASB process for treating fresh leachates from incineration plants. The ratio of volatile solids/total solids (VS/TS) of the anaerobic sludge in the UASB decreased significantly after a long-term operation due to the precipitation of calcium carbonate in the granules. Scanning electron microscopy (SEM) observation shows that Methanosaeta-like species were in abundance, accompanied by a variety of other species. The result was further confirmed by polymerase chain reaction-denaturing gradient gel electrophoresis (PCR-DGGE) and sequencing.     

Effect of organic loading rate on the performance of an up-flow anaerobic sludge blanket reactor treating olive mill effluent

The primary objective of this study was to evaluate the effects of the organic loading rate on the performance of an up-flow anaerobic sludge blanket (UASB) reactor treating olive mill effluent (OME), based on the following indicators: (i) chemical oxygen demand (COD) removal efficiency; and (ii) effluent variability (phenol, suspended solids, volatile fatty acids, and pH stability). The UASB reactor was operated under different operational conditions (OLRs between 0.45 and 32 kg COD/m³·day) for 477 days. The results demonstrated that the UASB reactor could tolerate high influent COD concentrations. Removal efficiencies for the studied pollution parameters were found to be as follows: COD, 47∼92%; total phenol, 34∼75%; color, 6∼46%; suspended solids, 34∼76%. The levels of VFAs in the influent varied between 310 and 1,750 mg/L. Our measurements of the VFA levels indicated that some of the effluent COD could be attributed to VFAs (principally acetate, butyrate, iso-butyrate, and propionate) in the effluent, which occurred at levels between 345 and 2,420 mg/L. As the OLRs were increased, more VFAs were measured in the effluent. A COD removal efficiency of 90% could be achieved as long as OLR was kept at a level of less than 10 kg COD/m³·day. However, a secondary treatment unit for polishing purposes is necessary to comply with discharge standards.     

Treatment of distillery spentwash by hybrid UASB reactor

A laboratory-scale hybrid UASB reactor, which combined an UASB in the lower part and a filter in the upper part, was used for the treatment of distillery spentwash. The reactor was operated under ambient conditions for 380 days. Using anaerobically digested sewage sludge as a seed, the start-up of the reactor and the cultivation of active granular sludge was completed within three months period. Scanning electron microscopic (SEM) observation of the granules showed the presence of Mehtanonthrix-like bacteria as the dominant species. Following the start-up the organic loading rate (OLR) was increased, stepwise, to 36 kg COD/m³ · d at a constant hydraulic retention time (HRT) of 6 h. COD removal efficiency was 80% even at a high OLR of 36 kg COD/m³ · d. Biogas rich in methane content (80%), with a maximum specific biogas yield of 0.40 m³ CH₄/kg · COD was produced. Polypropylene pall rings filter medium in the upper-third of the reactor was very effective as a gas-liquid-solid (GLS) separator, and retained the biomass in addition. The study indicated that hybrid UASB is a very feasible alternative for the treatment of high-strength wastewaters like distillery spentwash.     

High upflow velocity and organic loading rate improve granulation in upflow anaerobic sludge blanket reactors

Five laboratory scale upflow anaerobic sludge blanket (UASB) reactors were seeded with nongranular sewage sludge. Granulation was obtained after 15–35 days when between 0.5 and 2.0m/h upflow liquid velocity was applied, with an organic loading rate (OLR) of 8g COD/l.d (COD is the chemical oxygen demand). Granules had different physical characteristics and specific activity (g COD_REMOVED/g volatile suspended solids) depending on the upflow liquid velocity applied. Granules were obtained in short startup periods (5 and 14 days) when a pilot-scale (180l) UASB reactor with a height of 4.7m was used to study hydraulic effects on the granulation process.     

Thermophilic treatment of bulk drug pharmaceutical industrial wastewaters by using hybrid up flow anaerobic sludge blanket reactor

The hybrid up flow anaerobic sludge blanket reactor was evaluated for efficacy in reduction of chemical oxygen demand (COD) and biochemical oxygen demand (BOD) of bulk drug pharmaceutical wastewater under different operational conditions. The start-up of the reactor feed came entirely with glucose, applied at an organic loading rate (OLR) 1 kg COD/m³ d. Then the reactor was studied at different OLRs ranging from 2 to 11 kg COD/m³ d with pharmaceutical wastewater. The optimum OLR was found to be 9 kg COD/m³ d, where we found 65–75% COD and 80–94% of BOD reduction with biogas production containing 60–70% of methane and specific methanogenic activity was 320 ml CH₄/g-VSS d. By the characterization studies of effluent using GC–MS, the hazardous compounds like phenol, l,2-methoxy phenol, 2,4,6-trichloro phenol, dibutyl phthalate, 1-bromo naphthalene, carbamazepine and antipyrine were present. After the treatment, these compounds degraded almost completely except carbamazepine. Thermophilic methanothrix and methanosaetae like bacteria are present in the granular sludge.     

Extending the diffuse layer model of surface acidity constant behaviour: II. Estimation of intrinsic acidity and electrolyte ion site binding constants

Abstract

The main objective of this work was to study the capacity of bioaccumulation of copper in an upflow anaerobic sludge blanket (UASB) reactor, for the treatment of acid mine drainages (AMD). UASB reactor of 0.8 L was fed with sodium acetate, the organic loading rate (OLR) was set at 2.0gCOD/Ld, and experiments were performed in the reactor during 115 days. After 30 days, the COD removal efficiency was 90%. In the stationary stage, the higher production methane was 0.253 L/Ld. The reactor was added with 20 mgCu(II)/L during 30 days. The copper bioaccumulation was 98% and it was accumulated gradually in sludge until reaching a 61.6 mgCu(II)/gTS. The toxicity study demonstrated that the copper concentration at which the level of specific methanogenic activity (SMA) of the biogranules was reduced to 50% of the control (IC₅₀), was 280 mgCu(N)/L     

Methane production by treating vinasses from hydrous ethanol using a modified UASB reactor

Background

A modified laboratory-scale upflow anaerobic sludge blanket (UASB) reactor was used to obtain methane by treating hydrous ethanol vinasse. Vinasses or stillage are waste materials with high organic loads, and a complex composition resulting from the process of alcohol distillation. They must initially be treated with anaerobic processes due to their high organic loads. Vinasses can be considered multipurpose waste for energy recovery and once treated they can be used in agriculture without the risk of polluting soil, underground water or crops. In this sense, treatment of vinasse combines the elimination of organic waste with the formation of methane. Biogas is considered as a promising renewable energy source. The aim of this study was to determine the optimum organic loading rate for operating a modified UASB reactor to treat vinasse generated in the production of hydrous ethanol from sugar cane molasses.

Results

The study showed that chemical oxygen demand (COD) removal efficiency was 69% at an optimum organic loading rate (OLR) of 17.05 kg COD/m³-day, achieving a methane yield of 0.263 m³/kg COD_added and a biogas methane content of 84%. During this stage, effluent characterization presented lower values than the vinasse, except for potassium, sulfide and ammonia nitrogen. On the other hand, primers used to amplify the 16S-rDNA genes for the domains Archaea and Bacteria showed the presence of microorganisms which favor methane production at the optimum organic loading rate.

Conclusions

The modified UASB reactor proposed in this study provided a successful treatment of the vinasse obtained from hydrous ethanol production.Methanogen groups (Methanobacteriales and Methanosarcinales) detected by PCR during operational optimum OLR of the modified UASB reactor, favored methane production.

     

Effect of starch addition on the biological conversion and microbial community in a methanol-fed UASB reactor during long-term continuous operation

The effect of starch addition on the microbial composition and the biological conversion was investigated using two upflow anaerobic sludge bracket (UASB) reactors treating methanolic wastewater: one reactor was operated with starch addition, and another reactor was operated without starch addition. Approximately 300 days of operation were performed at 30 kg COD/m³/d, and then, the organic load of the reactors was gradually increased to 120 kg COD/m³/d. Successful operation was achieved at 30 kg COD/m³/d in both reactors; however, the methanol-fed reactor did not perform well at 120 kg COD/m³/d while the methanol-starch-fed reactor did. The granule analysis revealed the granule developed further only in the methanol-starch-fed reactor. The results of the microbial community analysis revealed more Methanosaeta cells were present in the methanol-starch-fed reactor, suggesting the degradation of starch produced acetate as an intermediate, which stimulated the growth of Methanosaeta cells responsible for the extension of granules.     

A further study of the anaerobic biotreatment of malt whisky distillery pot ale using an UASB system

Pot ale from a pilot-scale malt whisky distillery was treated using a mesophilic upflow anaerobic sludge blanket (UASB) digester. Stable operation was observed at organic loading rates (OLRs) of 5.46 kg COD/m3 day or less when the pot ale was diluted with tap water. Digester failure occurred when undiluted pot ale was used, even though OLR was less than 5 kg COD/m3 day. Overall performance was worse than that observed previously when UASB digesters were used to treat pot ale from a different source supplemented with trace elements. A substantial proportion of effluent chemical oxygen demand (COD) was present as volatile fatty acids (VFA), particularly during periods of reactor stress, indicating that overall performance was limited by the rate of VFA conversion. Wastewater alkalinity rose during digestion. The sludge which developed in the reactor was flocculent but did not form compact granules.     

The influence of anaerobic pretreatment on the nitrogen removal from biosynthetic pharmaceutical wastewaters

The C:N ratio of the pharmaceutical wastewaters is usually suitable for a combination of the anaerobic pretreatment with the high COD removal and aerobic posttreatment with the efficient biological N removal. This kind of anaerobic-aerobic process was tested in semipilot scale by using a UASB reactor and an activated sludge system with a predenitrification (total volume 100 1). It was found that at a total HRT of 2.3 days an average of 97.5% of COD and 73.5% of total N was removed. The UASB reactor was operated at 30°C with a volumetric loading rate of 8.7 kg.m^-3.d^-1, the efficiency of COD removal was 92.2%. The processes, which take part in the biological removal of nitrogen, especially the nitrification, were running with lower rates than usually observed in aerobic treatment systems.Abbreviations AAO anaerobic anoxic oxic configuration - AOO anaerobic oxic oxic configuration - B _V volumetric organic loading rate (kg COD.m^-3. d^-1) - dB _x specific COD removal rate (mg COD. g^-1 VSS. d^-1) - DNR denitrification rate (mg N–NO₃. g^-1 VSS. h^-1) - E_COD efficiency of COD removal (%) - HRT hydraulic retention time (d) - NR nitrification rate (mg N–NO₃. g^-1 VSS. h^-1) - R recirculation ratio (%) - SBP specific biogas production (m³.kg^-1 removed COD) - SRT solids retention time; sludge age (d) - SS suspended solids (g.1^-1) - UASB upflow anaerobic sludge blanket reactor - VSS volatile suspended solids (g.1^-1)     

Trace elements enhance biofilm formation in UASB reactor for solo simple molecule wastewater treatment

In this paper, trace elements (TE) adding was investigated in one bench-scale UASB reactor treating solo simple molecule wastewater with the aim of evaluating its effect on enhancing biofilm formation. After adding sufficient TE (3 mL/L) in the influent, during 3 days, COD removal efficiency increased from 74% to 90% comparing to no adding TE. Over 55 days of operation, the organic loading rate (OLR) reached 11 g/L/day with COD removal efficiencies greater than 90%. While in the steady running period no effect even improvement on treatment performance was observed without any TE adding. The results illuminated that TE accounted for quick start-up of the UASB biofilm system rather than ever known biocatalyst.     

Treatment of slaughterhouse wastewater in a UASB reactor and an anaerobic filter

A study was performed to assess the feasibility of anaerobic treatment of slaughterhouse wastewaters in a UASB (Upflow Anaerobic Sludge Blanket) reactor and in an AF (Anaerobic Filter). Among the different streams generated, the slaughter line showed the highest organic content with an average COD of 8000 mg/l, of which 70% was proteins. The suspended solids content represented between 15 and 30% of the COD. Both reactors had a working volume of 21. They were operated at 37°C. The UASB reactor was run at OLR (Organic Loading Rates) of 1–6.5 kg COD/m³/day. The COD removal was 90% for OLR up to 5 kg COD/m³/day and 60% for an OLR of 6.5 kg COD/m³/day. For similar organic loading rates, the AF showed lower removal efficiencies and lower percentages of methanization. At higher OLR sludge, flotation occurred and consequently the active biomass was washed out from the filter. The results indicated that anaerobic treatment systems are applicable to slaughterhouse wastewaters and that the UASB reactor shows a better performance, giving higher COD removal efficiencies than the AF.     

Characteristics of the bioreactor landfill system using an anaerobic-aerobic process for nitrogen removal

A sequential upflow anaerobic sludge blanket (UASB) and air-lift loop sludge blanket (ALSB) treatment was introduced into leachate recirculation to remove organic matter and ammonia from leachate in a lab-scale bioreactor landfill. The results showed that the sequential anaerobic-aerobic process might remove above 90% of COD and near to 100% of NH4+ -N from leachate under the optimum organic loading rate (OLR). The total COD removal efficiency was over 98% as the OLR increased to 6.8-7.7 g/l d, but the effluent COD concentration increased to 2.9-4.8 g/l in the UASB reactor, which inhibited the activity of nitrifying bacteria in the subsequent ALSB reactor. The NO3- -N concentration in recycled leachate reached 270 mg/l after treatment by the sequential anaerobic-aerobic process, but the landfill reactor could efficiently denitrify the nitrate. After 56 days operation, the leachate TN and NH4+ -N concentrations decreased to less than 200 mg/l in the bioreactor landfill system. The COD concentration was about 200 mg/l with less than 8 mg/l BOD in recycled leachate at the late stage. In addition, it was found that nitrate in recycled leachate had a negative effect on waste decomposition.     

Anaerobic digestion of a petrochemical effluent using an upflow anaerobic sludge blanket reactor

Summary An UASB reactor was used for the anaerobic conversion of an acidic petrochemical effluent into a methane-rich biogas. Reactor efficiency was optimal at an HRT of 1.78 days and loading rate of 7.255 kg COD/m₃.d, A COD reduction of 83% was obtained. The gas production was 2.64 m/m .d (STP) and contained more than 90% CH₄. A further increase in the loading rate resulted in a drastic decrease in the reactor effectivity.     

Effect of long-term cobalt deprivation on methanol degradation in a methanogenic granular sludge bioreactor

The effect of the trace metal cobalt on the conversion of methanol in an upflow anaerobic sludge bed (UASB) reactor was investigated by studying the effect of cobalt deprivation from the influent on the reactor efficiency and the sludge characteristics. A UASB reactor (30 degrees C; pH 7) was operated for 261 days at a 12-h hydraulic retention time (HRT). The loading rate was increased stepwise from 2.6 g chemical oxygen demand (COD) x L reactor(-1) x d(-1) to 7.8 g COD x L reactor(-1) x d(-1). Cobalt deprivation had a strong impact on the methanogenic activity of the sludge. In batch tests, the methanogenic activity of the sludge with methanol as the substrate increased 5.3 (day 28) and 2.1 (day 257) times by addition of 840 nM of cobalt. The sludge had an apparent K(m) for cobalt of 948 nM after 28 days of operation and 442 nM at the end of the run. Cobalt deprivation during 54 days of operation led to a methanol conversion efficiency of only 55%. Continuous addition of cobalt (330 nM) for 33 days improved the methanol removal efficiency to 100%. In this period of cobalt dosing, the cobalt concentration in the sludge increased 2.7 times up to 32 microg x g TSS(-1). Upon omission of the cobalt addition, cobalt washed-out at a stable rate of 0.1 microg x g VSS(-1) x d(-1). At the end of the run, the cobalt concentration of the sludge was similar to that of the seed sludge.     

Treatment of poultry slaughterhouse wastewater in hybrid upflow anaerobic sludge blanket reactor packed with pleated poly vinyl chloride rings

In this study, the performance of 5.4 L hybrid upflow anaerobic sludge blanket (HUASB) reactor for treating poultry slaughterhouse wastewater under mesophilic conditions (29-35 °C), was investigated. After starting-up, the reactor was loaded up to an OLR of 19 kg COD/m³ d and achieved varied TCOD and SCOD removal efficiencies of 70-86% and 80-92%, respectively. The biogas was varied between 1.1 and 5.2 m³/m³ d with the maximum methane content of 72%. The maximum methane yield was 0.32 m³/kg COD_removed at an OLR of 9.27 kg COD/m³ d. Black matured granules of size between 2.5 and 5 mm were observed at the end of 225 d operation. RTD study showed the flow behavior was in mixed regime at the end of performance study. Step wise polynomial regression analysis was fitted well. Methanobacterium and Methanosaeta bacteria were dominant at the end of start-up whereas Methanosarcina, Cocci and rods were predominant at the end of performance studies.     

Recycle in upflow anaerobic sludge blanket reactor on treatment of real textile dye effluent

The discharge of textile wastewater containing dye in the environment is varying for both toxicology and esthetical reasons as dyes impede light penetration, damage the quality of the receiving streams. Upflow anaerobic sludge blanket reactor with anaerobic digester sludge treating starch wastewater has been used to investigate the removal efficiency of chemical oxygen demand (COD) and colour of textile dye wastewater. In this study, the starch and textile dye wastewater was mixed at 70 and 30%, respectively, and the experiments were carried out with recycle of treated wastewater at different percentage as 10, 20, 30 and 40. Maximum removal of COD and colour was 96% and 93.3%, respectively, at 30% recycle. At various OLR and HRT, the maximum removal of COD, colour was 95.9%, 93% at 6.81 kg COD/m³d and 96%, 93% with 24 h of HRT. The maximum production of biogas at 24 h of HRT with 30% recycle was about 355 l/d. The Volatile fatty acid/Alkalinity ratio of methanogenic reactor was found to be 0.049–0.053. The result provided evidence, the starch and dye wastewater have wide variation in their characteristics was treated on combination, this new technology supports the effective utilization of starch waste in destruction of dye.     

Effects of cationic polymer on performance of UASB reactors treating low strength wastewater

The effect of cationic polymer additives on biomass granulation and COD removal efficiency had been examined in lab-scale upflow anaerobic sludge blanket (UASB) reactors, treating low strength synthetic wastewater (COD 300-630 mg/l). Under identical conditions, two reactors were operated with and without polymer additives in inoculum under four different organic loading rates (OLRs). The optimum polymer dose was adopted based upon the results of jar test and settling test carried out with inoculum seed sludge. With the use of thick inoculum, SS greater than 110 g/l and VSS/SS ratio less than 0.3, granulation was observed in UASB reactor treating synthetic wastewater as well as actual sewage, when OLR was greater than 1.0 kg COD/m(3) d. Polymer additive with such thick inoculum was observed to deteriorate percentage granules and COD removal efficiency compared to inoculum without polymer additives. At OLR less than 1.0 kg COD/m(3) d, proper granulation could not be achieved in both the reactors inoculated with and without polymer additive. Also, under this low loading, drastic reduction in COD removal efficiency was observed with polymer additives in inoculum. Hence, it is rational to conclude that biomass granulation for treatment of low strength biodegradable wastewater depends on the applied loading rate and selection of thick inoculum sludge.     

Potential cause of aerobic granular sludge breakdown at high organic loading rates

Aerobic sludge granules are compact, strong microbial aggregates that have excellent settling ability and capability to efficiently treat high-strength and toxic wastewaters. Aerobic granules disintegrate under high organic loading rates (OLR). This study cultivated aerobic granules using acetate as the sole carbon and energy source in three identical sequencing batch reactors operated under OLR of 9–21.3 kg chemical oxygen demand (COD) m⁻³ day⁻¹. The cultivated granules removed 94–96% of fed COD at OLR up to 9–19.5 kg COD m⁻³ day⁻¹, and disintegrated at OLR of 21.3 kg COD m⁻³ day⁻¹. Most tested isolates did not grow in the medium at >3,000 mg COD l⁻¹; additionally, these strains lost capability for auto-aggregation and protein or polysaccharide productivity. This critical COD regime correlates strongly with the OLR range in which granules started disintegrating. Reduced protein quantity secreted by isolates was associated with the noted poor granule integrity under high OLR. This work identified a potential cause of biological nature for aerobic granules breakdown.