On-chip detection of myoglobin based on fluorescence

A disposable immunosensor cartridge was developed that allows antibodies to be immobilized on the surface for the detection of myoglobin, a marker for the early assessment of acute myocardial infarction (AMI) using fluorescence techniques. The anti-myoglobin antibody was immobilized on a polystyrene substrate based on covalent bonding via silanization. The immunosensor chip layers were fabricated from sheets by CO(2)-laser ablation. The functionalized polystyrene surfaces were characterized by contact angle measurement, X-ray photoelectron spectroscopy (XPS), and atomic force microscopy (AFM). After the antigen-antibody reaction as a sandwich enzyme-linked immunosorbent assay (ELISA) with a horseradish peroxidase-conjugated secondary antibody (HRP-anti-myoglobin), addition of fluorogenic substrate produced a fluorescent dye which was quantified on-chip using fluorescent technique. The immunosensor response was linear for myoglobin concentrations between 20 and 230 ng/ml (r=0.991, n=3). The detection limit was found to be 16 ng/ml, which is lower than the clinical cut-off value for myoglobin in healthy patients. This protocol could be extended to the detection of other important cardiac markers simultaneously in microchannels.     

Nisin adsorption on hydrophilic and hydrophobic surfaces: evidence of its interactions and antibacterial activity

Study of peptides adsorption on surfaces remains a current challenge in literature. A complementary approach, combining X‐ray photoelectron spectroscopy (XPS) and time‐of‐flight secondary ion mass spectrometry (ToF‐SIMS) was used to investigate the antimicrobial peptide nisin adsorption on hydrophilic and hydrophobic surfaces. The native low density polyethylene was used as hydrophobic support and it was grafted with acrylic acid to render it hydrophilic. XPS permitted to confirm nisin adsorption and to determine its amount on the surfaces. ToF‐SIMS permitted to identify the adsorbed bacteriocin type and to observe its distribution and orientation behavior on both types of surfaces. Nisin was more oriented by its hydrophobic side to the hydrophobic substrate and by its hydrophilic side to the outer layers of the adsorbed peptide, in contrast to what was observed on the hydrophilic substrate. A correlation was found between XPS and ToF‐SIMS results, the types of interactions on both surfaces and the observed antibacterial activity. Such interfacial studies are crucial for better understanding the peptides interactions and adsorption on surfaces and must be considered when setting up antimicrobial surfaces. Copyright © 2013 European Peptide Society and John Wiley & Sons, Ltd.     

Microwave-assisted synthesis of blue fluorescent molybdenum nanoclusters with maltose-cysteine Schiff base for detection of myoglobin and γ-aminobutyric acid in biofluids

The fabrication of stable fluorescent MoNCs (molybdenum nanoclusters) in aqueous media is quite challenging as it is not much explored yet. Herein, we report a facile and efficient strategy for fabricating MoNCs using 2,3 dialdehyde maltose-cysteine Schiff base (DAM-cysteine) as a ligand for detecting myoglobin and γ-aminobutyric acid (GABA) in biofluids with high selectivity and sensitivity. The DAM-cysteine-MoNCs displayed fluorescence of bright blue color under a UV light at 365 nm with an emission peak at 444 nm after excitation at 370 nm. The synthesized DAM-cysteine-MoNCs were homogeneously distributed with a mean size of 2.01 ± 0.98 nm as confirmed by the high-resolution transmission electron microscopy (HR-TEM). Further, X-ray photoelectron spectroscopy (XPS) and Fourier transform infrared (FT-IR) techniques were utilized to confirm the elemental oxidation states and surface functional groups of the DAM-cysteine-MoNCs. After the addition of myoglobin and GABA, the emission peak of DAM-cysteine-MoNCs at 444 nm was significantly quenched. This resulted in the development of a quantitative assay for the detection of myoglobin (0.1–0.5 μM) and GABA (0.125–2.5 μM) with the lower limit of detection as 56.48 and 112.75 nM for myoglobin and GABA, respectively.     

Neurotransmitter analog tethered to a silicon platform for neuro-BioMEMS applications

The design of chemically well-defined, machinable surfaces containing neuroactive molecules offers potential for fundamental neuroscience and clinical neural engineering applications. Here we report the assembly and characterization of silicon platforms containing a tethered form of muscimol. Muscimol, an analog of the inhibitory neurotransmitter gamma-aminobutyric acid (GABA), is a potent agonist at postsynaptic GABA(A) and GABA(C) receptors. Surfaces were assembled using covalent avidin conjugation to silanized silicon followed by high-affinity avidin-biotin binding of a biotinylated derivative of muscimol (muscimol-biotin). Contact angle measurements, ellipsometry, and X-ray photoelectron spectroscopy (XPS) were conducted to characterize the wettability, thickness, and chemical composition of progressively deposited surface layers. The data demonstrate successful incorporation of a neurotransmitter analog as part of a layered, silicon-based structure possessing robust and specific biomolecular composition. These findings represent a step toward the design of platforms for applications involving control and modulation of neural signaling.     

Investigation of spacer length effect on immobilized Escherichia coli pili-antibody molecular recognition by AFM

The immobilization of antibodies to sensor surfaces is critical in biochemical sensor development. In this study, Poly(ethylene glycol) (PEG) and Jeffamine spacers were employed to tether Escherichia coli K99 pilus antibody to silicon wafer surfaces for the purpose of improving the orientation of antibody as well as reducing the steric hindrance. To illustrate the effect of spacer length, a variety of linear polymers were used to covalently attach the antibodies to silicon surfaces. Atomic Force Microscopy (AFM) and X-ray photoelectron spectroscopy (XPS) were used to characterize the surface morphology and chemical composition at each reaction step. The effect of spacer length in improving the specificity of immobilized antibody was investigated by attaching E. coli on the end of an AFM tip. The distribution of unbinding force and rupture distance from the force-distance curves obtained by AFM showed that the introduction of PEG spacer facilitates bacterial recognition which can improve the incidence of interactions by up to 90%. J600 proved to be the most effective spacer overcoming the steric hindrance seen with direct immobilization of antibody. In addition, the force spectroscopy reveals the elementary force quantum of E. coli-antibody to be 0.3 nN.     

Synthesis and characterization of biocompatible polymer interlayers on titanium implant materials

A bifunctional copolymer series of (4-vinylbenzyl)phosphonic acid diethylester and N-acryloxysuccinimide was developed as an interlayer with the aim of immobilizing proteins on titanium surfaces. Copolymers with varying compositions were synthesized, and an alternating copolymerization of the two monomers was found. The copolymers form ultrathin films of about 2-8 nm on titanium surfaces in a simple dipping process, as estimated from the attenuation of the titanium X-ray photoelectron spectroscopy (Ti-XPS) signal. The films were characterized by infrared spectroscopy, XPS, and time-of-flight secondary ion mass spectrometry. The results indicate that the immobilization is due to phosphonate groups, and thus the phosphonate content of the copolymers is decisive for the final film thickness. These polymer films were examined for their potential protein binding capacity by using trifluoroethylamine derivatization and subsequent XPS analysis as a reactivity assay.     

Bioactive polymer fibers to direct endothelial cell growth in a three-dimensional environment

This study reports the fabrication of bioactive polymer fibers onto which signaling molecules can control and direct cell responses. To encourage and control directional biological responses, GRGDS peptides were immobilized onto the surface of 100 microm diameter poly(ethylene terephtalate) (PET) fibers (monofilaments). PET fiber surfaces were first coated with a thin polymeric interfacial bonding layer bearing amine groups by plasma polymerization. Carboxy-methyl-dextran (CMD) was covalently grafted onto the surface amine groups using water-soluble carbodiimide chemistry. GRGDS were covalently immobilized onto CMD-coated fiber surfaces. X-ray photoelectron spectroscopy (XPS) analyses enabled characterization of the multilayer fabrication steps. Human umbilical vein endothelial cells were seeded and grown on fibers to investigate cell patterning behavior (i.e., adhesion, spreading, cytoskeleton organization, and cell orientation). Cell adhesion was reduced on CMD-coated fibers, whereas amine- and GRGDS-coated fibers promoted cell adhesion and spreading. Cell adhesion was enhanced as the GRGDS concentration increased. Epifluorescence microscopic visualization of cells on RGD-coated substrates showed well-defined stress fibers and sharp spots of vinculin, typical of focal adhesions. In comparison to plasticware commonly used in cell cultures, fiber curvature promoted cell orientation along the fiber axis.     

Nanometer scale organization of mixed surfactin/phosphatidylcholine monolayers.

Mixed monolayers of the surface-active lipopeptide surfactin-C(15) and of dipalmitoyl phosphatidylcholine (DPPC) were deposited on mica and their nanometer scale organization was investigated using atomic force microscopy (AFM) and x-ray photoelectron spectroscopy (XPS). AFM topographic images revealed phase separation for mixed monolayers prepared at 0.1, 0.25, and 0.5 surfactin molar ratios. This was in agreement with the monolayer properties at the air-water interface indicating a tendency of the two compounds to form bidimensional domains in the mixed systems. The step height measured between the surfactin and the DPPC domains was 1.2 +/- 0.1 nm, pointing to a difference in molecular orientation: while DPPC had a vertical orientation, the large peptide ring of surfactin was lying on the mica surface. The N/C atom concentration ratios obtained by XPS for pure monolayers were compatible with two distinct geometric models: a random layer for surfactin and for DPPC, a layer of vertically-oriented molecules in which the polar headgroups are in contact with mica. XPS data for mixed systems were accounted for by a combination of the two pure monolayers, considering respective surface coverages that were in excellent agreement with those measured by AFM. These results illustrate the complementarity of AFM and XPS to directly probe the molecular organization of multicomponent monolayers.     

Chemical force microscopy of cellulosic fibers

Atomic force microscopy with chemically modified cantilever tips (chemical force microscopy) was used to study the pull-off forces (adhesion forces) on cellulose model surfaces and bleached softwood kraft pulp fibers in aqueous media. It was found that for the –COOH terminated tips, the adhesion forces are dependent on pH, whereas for the –CH₃ and –OH terminated tips adhesion is not strongly affected by pH. Comparison between the cellulose model surfaces and cellulosic fibers under our experimental conditions reveal that surface roughness does not affect adhesion strongly. X-ray photoelectron spectroscopy (XPS) and Fourier Transformed Infrared (FTIR) spectroscopy reveal that both substrate surfaces have homogeneous chemical composition. The results show that chemical force microscopy can be used for the chemical characterization of cellulose surfaces at a nano-level.     

Electrochemical impedance detection of DNA hybridization based on dendrimer modified electrode

Bioactive ultrathin films with the incorporation of amino-terminated G4 PAMAM dendrimers have been prepared via layer-by-layer self-assembly methods on a gold electrode and used for the DNA hybridization analysis. Surface plasmon resonance (SPR), X-ray photoelectron spectroscopy (XPS), and electrochemical impedance spectroscopy (EIS) are used to characterize the successful construction of the multicomponent film on the gold substrate. The dendrimer-modified surfaces improve the immobilization capacity of the probe DNA greatly, compared to the AET (2-aminoethanethiol) SAM sensor surfaces without dendrimer molecules. DNA hybridization analysis is monitored by EIS. The dendrimer-based electrochemical impedance DNA biosensor shows high sensitivity and selectivity for DNA hybridization assay. The multicomponent films also display a high stability during repeated regeneration and hybridization cycles.     

Immobilization of biomolecules on polyurethane membrane surfaces.

Lipophilic polymer membranes incorporating binding sites are widely used in various potentiometric, amperometric, and optical sensors. Here, we report on the biofunctional modification of the surface of a Ca(2+)-selective membrane. A photoactivatable biotin derivative was synthesized and covalently immobilized on a soft polyurethane membrane. The modified polymer was characterized by X-ray photoelectron spectroscopy (XPS) as well as by potentiometric measurements. The selective binding of streptavidin by the photo-cross-linked biotin derivative was demonstrated. The surface coverage obtained with different experimental protocols was analyzed by autoradiography using [(35)S]-streptavidin. The new approach may significantly extend the scope of applicability of potentiometric sensors.     

Magnetic circular dichroism studies on horseradish peroxidase.

Magnetic circular dichroism (MCD) spectra were observed for native (Fe(III)) horseradish peroxidase (peroxidase, EC 1.11.1.7), its alkaline form and fluoro- and cyano-derivatives, and also for reduced (Fe(II)) horseradish peroxidase and its carbonmonoxy-- and cyano- derivatives. MCD spectra were obtained for the cyano derivative of Fe(III) horseradish peroxidase, and reduced horseradish peroxidase and its carbonmonoxy- derivative nearly identical with those for the respective myoglobin derivatives. The alkaline form of horseradish peroxidase exhibits a completely different MCD spectrum from that of myoglobin hydroxide. Thus it shows an MCD spectrum which falls into the ferric low-spin heme grouping. Native horseradish peroxidase and its fluoro derivatives show almost identical MCD spectra with those for the respective myoglobin derivatives in the visible region, though some changes were detected in the Soret region. Therefore it is concluded that the MCD spectra on the whole are sensitive to the spin state of the heme iron rather than to the porphyrin structures. The cyanide derivative of reduced horseradish peroxidase exhibited a characteristic MCD spectrum of the low-spin ferrous derivative like oxy-myoglobin.     

A novel strategy to obtain a hyaluronan monolayer on solid substrates

The aim of this study was to find a novel simple method to obtain polysaccharide ultrathin layers on solid substrates to investigate the interaction between the surface and the biological environment. A Hyaluronan (Hyal) monolayer with a well-defined chemistry was obtained by exploiting the capability of organosilanes to spontaneously adhere onto glass surfaces. A silane alkylic chain was conjugated with Hyal, and the derivatized polysaccharide was allowed to spontaneously adhere onto a glass surface. The elemental analysis of the modified polysaccharide demonstrated that one out of five disaccharide units was conjugated with the alkyl silane chain, corresponding to a substitution degree of the carboxylate groups of approximately 20%. The film of the modified polysaccharide was characterized by means of X-ray photoelectron spectroscopy (XPS), water contact angle, and atomic force microscopy (AFM) measurements. XPS analysis demonstrated that we obtained a Hyal layer with a thickness of about 2.0 nm corresponding to a Hyal monolayer. The Hyal-coated surfaces appeared to be rather smooth and highly hydrophilic and showed significant resistance to nonspecific cell adhesion.     

Adsorption of a PEO–PPO–PEO triblock copolymer on metal oxide surfaces with a view to reducing protein adsorption and further biofouling

Abstract

Biomolecule adsorption is the first stage of biofouling. The aim of this work was to reduce the adsorption of proteins on stainless steel (SS) and titanium surfaces by modifying them with a poly(ethylene oxide) (PEO)–poly(propylene oxide) (PPO)–PEO triblock copolymer. Anchoring of the central PPO block of the copolymer is known to be favoured by hydrophobic interaction with the substratum. Therefore, the surfaces of metal oxides were first modified by self-assembly of octadecylphosphonic acid. PEO–PPO–PEO preadsorbed on the hydrophobized surfaces of titanium or SS was shown to prevent the adsorption of bovine serum albumin (BSA), fibrinogen and cytochrome C, as monitored by quartz crystal microbalance (QCM). Moreover, X-ray photoelectron spectroscopy (XPS) and time-of-flight secondary ion mass spectrometry were used to characterize the surfaces of the SS and titanium after competitive adsorption of PEO–PPO–PEO and BSA. The results show that the adsorption of BSA is well prevented on hydrophobized surfaces, in contrast to the surfaces of native metal oxides.     

Introducing amine functionalities on a poly(3-hydroxybutyrate-co-3-hydroxyvalerate) surface: comparing the use of ammonia plasma treatment and ethylenediamine aminolysis

Amine functionalities were introduced onto the surface of poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) films by applying radio frequency ammonia plasma treatment and wet ethylenediamine treatment. The modified surfaces were characterized by X-ray photoelectron spectroscopy (XPS) for chemical composition and Raman microspectroscopy for the spatial distribution of the chemical moieties. The relative amount of amine functionalities introduced onto the PHBV surface was determined by exposing the treated films to the vapor of trifluoromethylbenzaldehyde (TFBA) prior to XPS analysis. The highest amount of amino groups on the PHBV surface could be introduced by use of ammonia plasma at short treatment times of 5 and 10 s, but no effect of plasma power within the range of 2.5-20 W was observed. Ethylenediamine treatment yielded fewer surface amino groups, and in addition an increase in crystallinity as well as degradation of PHBV was evident from Fourier transform infrared spectroscopy. Raman maps showed that the coverage of amino groups on the PHBV surfaces was patchy with large areas having no amine functionalities.     

Depth profiling of the elemental surface composition of the oral microorganism S. salivarius HB and fibrillar mutants by X-ray photoelectron spectroscopy.

X-ray photoelectron spectroscopy (XPS) on microbial cell surfaces requires freeze-drying of cells, and as a result, the cell surface appendages flatten out on the cell surface and form a collapsed fibrillar mass. At present, it is unclear how the density, length and composition of these fibrils influence the elemental surface composition as probed by XPS. The sampling depth of XPS can be varied by changing the electron take-off angle. In this article, we made a depth profiling of the collapsed fibrillar mass of Streptococcus salivarius HB and fibril-deficient mutants by angle-dependent XPS. Methylamine tungstate negative staining and ruthenium red staining followed by sectioning revealed distinct classes of fibrils with various lengths on each of the strains. Interpretation of the angle dependence of the oxygen/carbon (O/C) and phosphorus/carbon (P/C) surface concentration ratios of these strains was difficult. However, the angle dependence of the nitrogen/carbon (N/C) surface concentration ratio could be fully interpreted: N/C did not vary with sampling depth on a bald strain, S. salivarius HBC12 and on S. salivarius HB7, a strain with a dense array of fibrils of uniform length. N/C decreased with sampling depth in case of a sparsely fibrillated strain, S. salivarius HBV51 and eventually reached the value observed for the bald strain, HBC12. A high N/C at small sampling depth was observed for S. salivarius HB with protruding, protein rich fibrils. We conclude that elemental depth profiling of microbial cell surfaces by XPS can be interpreted to coincide with structural and biochemical information on the cell surface as obtained by electron microscopy and can therefore be considered as a useful technique to study structural features of cell surfaces in combination with electron microscopy.     

Depth profiling of the elemental surface composition of the oral microorganismS. salivarius HB and fibrillar mutants by X-ray photoelectron spectroscopy

X-ray photoelectron spectroscopy (XPS) on microbial cell surfaces requires freeze-drying of cells, and as a result, the cell surface appendages flatten out on the cell surface and form a collapsed fibrillar mass. At present, it is unclear how the density, length and composition of these fibrils influence the elemental surface composition as probed by XPS. The sampling depth of XPS can be varied by changing the electron take-off angle. In this article, we made a depth profiling of the collapsed fibrillar mass ofStreptococcus salivarius HB and fibril-deficient mutants by angle-dependent XPS. Methylamine tungstate negative staining and ruthenium red staining followed by sectioning revealed distinct classes of fibrils with various lengths on each of the strains. Interpretation of the angle dependence of the oxygen/carbon (O/C) and phosphorus/carbon (P/C) surface concentration ratios of these strains was difficult. However, the angle dependence of the nitrogen/carbon (N/C) surface concentration ratio could be fully interpreted: N/C did not vary with sampling depth on a bald strain,S. salivarius HBC12 and onS. salivarius HB7, a strain with a dense array of fibrils of uniform length. N/C decreased with sampling depth in case of a sparsely fibrillated strain,S. salivarius HBV51 and eventually reached the value observed for the bald strain, HBC12. A high N/C at small sampling depth was observed forS. salivarius HB with protruding, protein rich fibrils. We conclude that elemental depth profiling of microbial cell surfaces by XPS can be interpreted to coincide with structural and biochemical information on the cell surface as obtained by electron microscopy and can therefore be considered as a useful technique to study structural features of cell surfaces in combination with electron microscopy.     

Cyanide binding to Lucina pectinata hemoglobin I and to sperm whale myoglobin: an x-ray crystallographic study.

The x-ray crystal structures of the cyanide derivative of Lucina pectinata monomeric hemoglobin I (L. pectinata HbI) and sperm whale (Physeter catodon) myoglobin (Mb), generally taken as reference models for monomeric hemoproteins carrying hydrogen sulfide and oxygen, respectively, have been determined at 1.9 A (R-factor = 0. 184), and 1.8 A (R-factor = 0.181) resolution, respectively, at room temperature (lambda = 1.542 A). Moreover, the x-ray crystal structure of the L. pectinata HbI:cyanide derivative has been studied at 1.4-A resolution (R-factor = 0.118) and 100 K (on a synchrotron source lambda = 0.998 A). At room temperature, the cyanide ligand is roughly parallel to the heme plane of L. pectinata HbI, being located approximately 2.5 A from the iron atom. On the other hand, the crystal structure of the L. pectinata HbI:cyanide derivative at 100 K shows that the diatomic ligand is coordinated to the iron atom in an orientation almost perpendicular to the heme (the Fe-C distance being 1.95 A), adopting a coordination geometry strictly reminescent of that observed in sperm whale Mb, at room temperature. The unusual cyanide distal site orientation observed in L. pectinata HbI, at room temperature, may reflect reduction of the heme Fe(III) atom induced by free radical species during x-ray data collection using Cu Kalpha radiation.     

Atomic force microscopy imaging of DNA covalently immobilized on a functionalized mica substrate.

A procedure for covalent binding of DNA to a functionalized mica substrate is described. The approach is based on photochemical cross-linking of DNA to immobilized psoralen derivatives. A tetrafluorphenyl (TFP) ester of trimethyl psoralen (trioxalen) was synthesized, and the procedure to immobilize it onto a functionalized aminopropyl mica surface (AP-mica) was developed. DNA molecules were cross-linked to trioxalen moieties by UV irradiation of complexes. The steps of the sample preparation procedure were analyzed with x-ray photoelectron spectroscopy (XPS). Results from XPS show that an AP-mica surface can be formed by vapor phase deposition of silane and that this surface can be derivatized with trioxalen. The derivatized surface is capable of binding of DNA molecules such that, after UV cross-linking, they withstand a thorough rinsing with SDS. Observations with atomic force microscopy showed that derivatized surfaces remain smooth, so DNA molecules are easily visualized. Linear and circular DNA molecules were photochemically immobilized on the surface. The molecules are distributed over the surface uniformly, indicating rather even modification of AP-mica with trioxalen. Generally, the shapes of supercoiled molecules electrostatically immobilized on AP-mica and those photocross-linked on trioxalen-functionalized surfaces remain quite similar. This suggests that UV cross-linking does not induce formation of a noticeable number of single-stranded breaks in DNA molecules.     

Human serum albumin adsorption onto a-SiC:H and a-C:H thin films deposited by plasma enhanced chemical vapor deposition

In the present paper, we report the study of the adsorption behavior of a model protein such as human serum albumin (HSA) onto surfaces of a-SiC:H and a-C:H thin films deposited by using the plasma-enhanced chemical vapor deposition (PECVD) technique. The surface composition and surface energy of the various substrates as well as the evaluation of the adsorbed amount of protein has been carried out by means of X-ray photoelectron spectroscopy (XPS) and contact angle measurements. It has been found that HSA tends to preferentially adsorb on Si-rich surfaces, as far as the relative amount of adsorbed HSA decreases with increasing S-C concentration. Preliminary elements of mechanistic models are proposed for the correlation between chemical factors and the observed protein adsorption behavior.