Orange light‐emitting Ca3Mg3(PO4)4:Sm3+ phosphors

This work reports the photoluminescence properties of Ca₃Mg₃(PO₄)₄:Sm³⁺ phosphors that were synthesized by the combustion method. The phase formation and morphology of the prepared phosphors were analysed by X‐ray diffraction studies and scanning electron microscopy. Ca₃Mg₃(PO₄)₄:Sm³⁺ phosphors give orange light emission when excited by near‐ultraviolet (NUV) and blue light. The photoluminescence characteristics of the as‐prepared phosphors were investigated and their emission spectra showed three peaks due to ⁴G_5/2 → ⁶H_5/2, ⁴G_5/2 → ⁶H_7/2 and ⁴G_5/2 → ⁶H_9/2 transitions. The mechanism responsible for the concentration quenching of luminescence was found to be an electric dipole–dipole interaction. The CIE chromaticity coordinates suggested that the prepared phosphors are potential candidates for orange light‐emitting diodes (LEDs).     

Dy3+‐, Sm3+‐, Ce3+‐ and Tb3+‐activated optical properties of microcrystalline BaMgP2O7 phosphors

Photoluminescence (PL) and thermoluminescence (TL) properties of rare earth (RE) ion (RE = Dy³⁺, Sm³⁺, Ce³⁺, Tb³⁺) activated microcrystalline BaMgP₂O₇ phosphors are presented in this work. Non‐doped and doped samples of BaMgP₂O₇ were prepared using a solid state diffusion method and characterized by X‐ray diffraction (XRD), scanning electron microscopy (SEM), PL and TL. The XRD measurement confirmed the phase purity of the BaMgP₂O₇ host matrix. The average particle size was found through SEM measurement to be around 2 μm. All activators using the PL technique displayed characteristic excitation and emission spectra that corresponded to their typical f → f and f → d transitions respectively. Thermoluminescence measurements showed that BaMgP₂O₇:RE (RE = Dy³⁺, Sm³⁺, Tb³⁺, Ce³⁺) and co‐doped BaMgP₂O₇:Ce³⁺,Tb³⁺ phosphors have also TL behaviour.     

Synthesis and luminescence characterization of Y2BaZnO5:RE (RE = Eu3+, Tb3+, Pr3+ and Sm3+) phosphors

Modified synthesis and luminescence of Y₂BaZnO₅ phosphors activated with the rare earths (RE) Eu³⁺, Tb³⁺, Pr³⁺ and Sm³⁺ are reported. RE₂BaZnO₅ phosphors have attracted attention because of their interesting magnetic and optical properties; and are usually prepared using a two‐step solid‐state reaction. In the first step, carbonates or similar precursors are thoroughly mixed and heated at 900°C to decompose them to oxides. To eliminate the unwanted phases like BaRE₂O₄, the resulting powders are reheated at 1100°C for a long time. We prepared Y₂BaZnO₅ phosphors activated with various activators by replacing the first step with combustion synthesis. The photoluminescence results are presented. The photoluminescence results for Eu³⁺, Tb³⁺ and Pr³⁺ are in good agreement with the literature. However, photoluminescence emission from Sm³⁺ has not been documented previously. The excitation spectrum of Eu³⁺ is dominated by a charge transfer band around 261 nm, and an additional band around 238 nm is always present, irrespective of the type of activator. The presence of this band for all these different types of activators was interpreted as host absorption.     

Tunable lanthanide/transition metal ion‐doped novel phosphors for possible application in w‐LEDs: a review

Lanthanide‐based phosphors have been extensively investigated for their possible applications in solid‐state lighting technologies especially for white‐light‐emitting diodes. In this review article emphasis has been laid on discussing the recent developments of phosphors for warm white‐light production based on various optical characteristics such as quantum efficiency, thermal stability, short emission decay time, long‐term stability, facile synthesis, and low cost of production. We have tried to cover the essential and latest discoveries of the lanthanide/rare earth‐doped phosphors after 2010. New generations of narrow‐band phosphors have also been included. The optical and material properties of several novel phosphors and their luminescence characteristics have been thoroughly discussed.     

Photoluminescence,cathodoluminescence and thermal stability of Sm3+‐activated Sr3La(VO4)3 red‐emitting phosphors

A series of Sm³⁺‐activated Sr₃La(VO₄)₃ phosphors were synthesized by a facile sol‐gel method. X‐ray diffraction patterns and photoluminescence (PL)/cathodoluminescence (CL) spectra as well as PL decay curves were employed to characterize the obtained samples. Upon 402 nm light excitation, the characteristic emissions of Sm³⁺ ions corresponding to ⁴G_5/2→⁶H_J transitions were observed in all the as‐prepared products. The PL emission intensity was increased with increase in Sm³⁺ ion concentration, while concentration quenching occurred when the doping concentration was over 4 mol%. The non‐radiative energy transfer mechanism for concentration quenching of Sm³⁺ ions was dominated by dipole–dipole interaction and the critical distance was around 21.59 Å. Furthermore, temperature‐dependent PL emission spectra revealed that the obtained phosphors possessed good thermal stability with an activation energy of 0.19 eV. In addition, the CL spectra of the samples were almost the same as the PL spectra, and the CL emission intensity showed a tendency to increase with increase in accelerating voltage and filament current. These results suggest that the Sm³⁺‐activated Sr₃La(VO₄)₃ phosphors with good color coordinates, high color purity and superior thermal stability may be a potential candidate for applications in white light‐emitting diodes and field‐emission displays as red‐emitting phosphors.     

Analysis of electron–vibrational interaction in interconfigurational 5d➔4f transition of Eu2+ ions in Na5Ca4(PO4)4F

In this paper, the photoluminescence properties of Eu²⁺‐activated greenish‐blue‐emitting halophosphate phosphor Na₅Ca₄(PO₄)₄F were studied to estimate electron–vibrational interaction (EVI) parameters such as the Huang–Rhys factor, effective phonon energy, Stokes shift and zero phonon line (ZPL) position for various concentrations of dopant. The validity of the results was established by modeling the emission spectra, which was found to be in good agreement with the experimental photoluminescence spectra. Copyright © 2016 John Wiley & Sons, Ltd.     

Dy(3+) and Mn(2+) emission in fluoride- and chloride-based Na(3) (SO(4) )X (X = F or Cl) phosphors

In the present study, Na₃(SO₄)X (X = F or Cl) halosulphate phosphors have been synthesized by the solid‐state diffusion method. The phase formation of the compounds Na₃(SO₄)F and Na₃(SO₄)Cl were confirmed by X‐ray powder diffraction (XRD) measurement. Photoluminescence (PL) excitation spectrum measurement of Na₃(SO₄)F:Ce³⁺ and Na₃(SO₄)Cl:Ce³⁺ shows this phosphor can be efficiently excited by near‐ultraviolet (UV) light and presents a dominant luminescence band centred at 341 nm for Ce³⁺, which is responsible for energy transfer to Dy³⁺and Mn²⁺ ions. The efficient Ce³⁺ → Dy³⁺ energy transfer in Na₃(SO₄)F and Na₃(SO₄)Cl under UV wavelength was observed due to ⁴ F_9/2 to ⁶H_15/2 and ⁶H_13/2 level, while Ce³⁺ → Mn²⁺ was observed due to ⁴ T₁ state to ⁶A₁. The purpose of the present study is to develop and understanding the photoluminescence properties of Ce³⁺‐, Dy³⁺‐ and Mn²⁺‐doped fluoride and chloride Na₃(SO₄)X (X = F or Cl) luminescent material, which can be the efficient phosphors in many applications, such as scintillation applications, TL dosimetry and the lamp industry, etc. Copyright © 2012 John Wiley & Sons, Ltd.     

In vivo testing of a bioresorbable phosphate‐based optical fiber

Optical fibers have recently attracted a noticeable interest for biomedical applications because they provide a minimally invasive method for in vivo sensing, imaging techniques, deep‐tissue photodynamic therapy or optogenetics. The silica optical fibers are the most commonly used because they offer excellent optical properties, and they are readily available at a reasonable price. The fused silica is a biocompatible material, but it is not bioresorbable so it does not decompose in the body and the fibers must be ex‐planted after in vivo use and their fragments can present a considerable risk to the patient when the fiber breaks. In contrast, optical fibers made of phosphate glasses can bring many benefits because such glasses exhibit good transparency in ultraviolet‐visible and near‐infrared regions, and their solubility in water can be tailored by changing the chemical composition. The bioresorbability and toxicity of phosphate glass–based optical fibers were tested in vivo on male laboratory rats for the first time. The fiber was spliced together with a standard graded‐index multi‐mode fiber pigtail and an optical probe for in vitro pH measurement was prepared by the immobilization of a fluorescent dye on the fiber tip by a sol‐gel method to demonstrate applicability and compatibility of the fiber with common fiber optics.      

Synthesis and characterization of diphenyl quinoline and bromine‐activated diphenyl quinoline organic phosphors

A diphenyl quinoline (DPQ)‐conjugated derivative and bromine‐activated DPQ (Br‐DPQ) were synthesized in an inert gas atmosphere at 140 °C using Friedlander condensation. The compounds showed blue emission under a UV source. The structures were characterized by X‐ray diffraction and Fourier transform infrared spectroscopy. The photoluminescence properties of the compounds were analysed using excitation and emission spectra. The synthesized organic phosphors shows bright emission in the blue region, with peaks at 445 and 453 nm, respectively, for DPQ and Br‐DPQ in the powder form. The physical and photoluminescence properties of these organic compounds reveal promising blue emitters for high‐efficiency organic light‐emitting diodes. Copyright © 2013 John Wiley & Sons, Ltd.     

Microwave‐assisted sintering synthesis of greenish‐yellow emitting Sr2SiO4:Eu2+ phosphors

Europium ion (Eu²⁺) doped Sr₂SiO₄ phosphors with greenish‐yellow emission were synthesized using microwave‐assisted sintering. The phase structure and photoluminescence (PL) properties of the obtained phosphor samples were investigated. The PL excitation spectra of the Sr₂SiO₄:Eu²⁺ phosphors exhibited a broad band in the range of 260 nm to 485 nm with a maximum at 361 nm attributed to the 5f‐4d allowed transition of the Eu²⁺ ions. Under an excitation at 361 nm, the Sr₂SiO₄:Eu²⁺ phosphor exhibited a greenish‐yellow emission peak at 541 nm with an International‐Commission‐on‐Illumination (CIE) chromaticity of (0.3064, 0.4772). The results suggest that the microwave‐assisted sintering method is promising for the synthesis of phosphors owing to the decreased sintering time without the use of additional reductive agents.     

Co‐precipitation synthesis and luminescence properties of K2TiF6:Mn4+ red phosphors for warm white light‐emitting diodes

K₂TiF₆:Mn⁴⁺ red phosphors with different Mn⁴⁺ doping concentrations were obtained using the co‐precipitation method. X‐Ray diffraction, scanning electron microscopy, Raman spectra, Fourier transform infrared spectroscopy, photoluminescence excitation and emission spectra and decay curves were used to characterize the properties of K₂TiF₆:Mn⁴⁺ phosphors. Under excitation at 470 nm, an intense red emission peak around 631 nm corresponding to the ²E_g–⁴A₂ transition of Mn⁴⁺ was observed for 2.48 mol% K₂TiF₆:Mn⁴⁺ phosphors and was used as the optimum doping concentration. The excellent luminescent properties of K₂TiF₆:Mn⁴⁺ suggest that this material might be a promising red phosphor for generating warm white light in phosphor‐converted white light‐emitting diodes. Copyright © 2015 John Wiley & Sons, Ltd.     

Photoluminescence properties of a new orange–red‐emitting Sm3+–La3SbO7 phosphor

The antimonate compound La₃SbO₇ has high chemical stability, lattice stiffness and thermal stability. Orange–red‐emitting antimonate‐based phosphors La₃SbO₇:xSm³⁺ (x = 0.02, 0.05, 0.08, 0.10, 0.15, 0.20 and 0.25) were synthesized. The phase structure and photoluminescence properties of these phosphors were investigated. The emission spectrum obtained on excitation at 407 nm contained exclusively the characteristic emissions of Sm³⁺ at 568, 608, 654 and 716 nm, which correspond to the transitions from ⁴G_5/2 to ⁶H_5/2, ⁶H_7/2, ⁶H_9/2 and ⁶H_11/2 of Sm³⁺, respectively. The strongest emission was located at 608 nm due to the ⁴G_5/2→⁶H_7/2 transition of Sm³⁺, generating bright orange–red light. The critical quenching concentration of Sm³⁺ in La₃SbO₇:Sm³⁺ phosphor was determined as 10% and the energy transfer between Sm³⁺ was found to be through an exchange interaction. The International Commission on Illumination chromaticity coordinates of the La₃SbO₇:0.10Sm³⁺ phosphors are located in the orange–red region. The La₃SbO₇:Sm³⁺ phosphors may be potentially used as red phosphors for white light‐emitting diodes. Copyright © 2015 John Wiley & Sons, Ltd.     

Evaluation of trapping parameters of γ‐rays irradiated Dy3+‐doped LaPO4 phosphors

Thermoluminescence (TL) materials are widely used in radiation measurements. The best‐known applications of TL materials are in the dosimetry of ionizing radiation, and in CTV screen phosphors, scintillators, X‐ray laser materials, etc. The TL glow curve and its kinetic parameters for annealed LaPO₄ at different constant temperatures and for Dy³⁺‐doped LaPO₄ phosphors irradiated by gamma‐rays are reported here. The samples were irradiated using a ⁶⁰Co gamma‐ray source at a dose of 10 Gy and the heating rate used for TL measurements was 5ºC/s. The samples were characterized using X‐ray diffraction (XRD), Fourier transform infrared, transmission electron microscopy and TL techniques. The XRD pattern shows that the prepared phosphor has a good crystalline structure with an average crystallite size of ~ 18 nm. The samples show good TL peaks for 0.05, 0.1 and 0.2 mole % doping concentrations of Dy³⁺ ions and anneal above 400ºC. The TL glow curve characteristics of annealed LaPO₄ and Dy³⁺‐doped LaPO₄ were analyzed and trapping parameters calculated using various methods. All TL glow curves obey the second‐order kinetics with a single glow peak, which reveals that only one set of trapping parameter is set for a particular temperature. The TL sensitivity was found to depend upon the annealing temperature and Dy³⁺ doping concentration. The prepared sample may be a new nano phosphor and be useful in TL dosimetry. Copyright © 2014 John Wiley & Sons, Ltd.     

Optical properties of CaAl(SO4)2Br:RE (RE = Dy,Eu, Ce) novel phosphors

A new phosphor CaAl(SO₄)₂Br doped with Dy, Ce and Eu is reported. Rare earth (Dy, Eu and Ce)‐doped polycrystalline CaAl(SO₄)₂Br phosphors were prepared using a wet chemical reaction method and studied for X‐ray diffraction and photoluminescence (PL) characteristics. Dy³⁺ emission in the CaAl(SO₄)₂Br lattice was observed at 484 and 574 nm in the blue and yellow regions of the spectrum, which are assigned to ⁴ F_9/2 → ⁶H_15/2 and ⁴ F_9/2 → ⁶H_13/2 transitions of the Dy³⁺ ion, respectively. While the PL emission spectra of CaAl(SO₄)₂Br:Ce phosphor showed Ce³⁺ emission at 347 nm due to 5d → 4f transition of the Ce³⁺ ion. In a CaAl(SO₄)₂Br:Eu lattice, Eu³⁺ emissions were observed at 593 and 617 nm, coming from the ⁵D₀ → ⁷ F₁ and ⁵D₀ → ⁷ F₂ electron transitions, respectively. The PL study showed that the intensity of electric dipole transition at 617 nm dominates over that of magnetic dipole transition at 590 nm. The maximum PL intensity was obtained for a 1 mol% concentration of Eu³⁺ in CaAl(SO₄)₂Br host lattice. The results showed that the material may be a promising candidate as a blue‐, yellow‐ and red‐emitting phosphor. Copyright © 2013 John Wiley & Sons, Ltd.     

Investigation of UV‐emitting Gd3+‐doped LiCaBO3 phosphor

Incorporating the Gd³⁺ rare earth ion in the LiCaBO₃ host lattice resulted in narrow‐band UV‐B emission peaking at 315 nm, with excitation at 274 nm. The LiCaBO₃:Gd³⁺ phosphor was synthesized via the solid‐state diffusion method. The structural, morphological and luminescence properties of this phosphor were characterized by X‐ray diffraction (XRD) analysis, scanning electron microscopy (SEM) and photoluminescence (PL) spectroscopy. Electron paramagnetic resonance (EPR) characterization of the as‐prepared phosphors is also reported here. XRD studies confirmed the crystal formation and phase purity of the prepared phosphors. A series of different dopant concentrations was synthesized and the concentration‐quenching effect was studied. Critical energy transfer distance between activator ions was determined and the mechanism governing the concentration quenching is also reported in this paper. Copyright © 2015 John Wiley & Sons, Ltd.     

Enhancement of the luminescence properties of Sr3(PO4)2:Dy3+,Li+ white‐light‐emitting phosphors by charge compensator Li+ co‐doping

Sr₃(PO₄)₂:Dy³⁺,Li⁺ phosphors were prepared using a simple high temperature solid method for luminescence enhancement. The structures of the as‐prepared samples agreed well with the standard phase of Sr₃(PO₄)₂, even when Dy³⁺ and Li⁺ were introduced. Under ultraviolet excitation at 350 nm, the Sr₃(PO₄)₂:Dy³⁺ sample exhibited two emission peaks at 483 nm and 580 nm, which were due to the ⁴F_9/2 → ⁶H_15/2 and ⁴F_9/2 → ⁶H_13/2 transitions of Dy³⁺ ions, respectively. A white light was fabricated using these two emissions from the Sr₃(PO₄)₂:Dy³⁺ phosphors. The luminescence properties of Sr₃(PO₄)₂:Dy³⁺,Li⁺ phosphors, including emission intensity and decay time, were improved remarkably with the addition of Li⁺ as the charge compensator, which would promote their application in near‐ultraviolet excited white‐light‐emitting diodes.     

Systematic study of photoluminescence,lyoluminescence and mechanoluminescence in Ce3+‐ and Eu3+‐activated Li3PO4 phosphors

Li₃PO₄ phosphor was prepared using a modified solid‐state diffusion technique. In this work, photoluminescence, lyoluminescence and mechanoluminescence studies were carried out in a Li₃PO₄ microcrystalline powder doped with different rare earths. In photoluminescence studies, characteristic emission of Ce and Eu was observed. The lyoluminescence glow curves of Li₃PO₄ microcrystals show that lyoluminescence intensity initially increases with time and then decreases exponentially. The decay time consists of two components for all masses. The dependence of decay time, especially the longer component, on mass has been investigated. Experiments on γ‐irradiated crystals have proved that the light emission originates from the recombination of released F‐centres with trapped holes (V₂‐centres) at the sulfuric acid–solid interface. Incorporation of bivalent alkali in solid lithium phosphate leads to an enhancement of lyoluminescence. A possible explanation for the experimental results has been attempted. The phosphor has a mechanoluminescence single glow peak. Mechanoluminescence intensity under various loading conditions was investigated. It is observed that mechanoluminescence intensity increases with increasing impurity concentration and increasing piston impact velocity. The results may be considered as only being of academic interest in solid‐state materials. Copyright © 2013 John Wiley & Sons, Ltd.     

Luminescence properties of a novel red phosphor 6LaPO4–3La3PO7–2La7P3O18:Eu3+

Eu³⁺‐doped 6LaPO₄–3La₃PO₇–2La₇P₃O₁₈ red luminescent phosphors were synthesized by co‐deposition and high‐temperature solid‐state methods and its polyphase state was confirmed by X‐ray diffraction analysis. Transmission electron microscopy showed the grain morphology as a mixture of rods and spheres. Luminescence properties of the phosphor were investigated and its red emission parameters were evaluated as a function of Eu³⁺ concentration (3.00–6.00 mol%). Excitation spectra of 6LaPO₄–3La₃PO₇–2La₇P₃O₁₈:Eu³⁺ showed strong absorption bands at 280, 395, and 466 nm, while the luminescence spectra exhibited prominent red emission peak centred at 615 nm (⁵D₀→⁷F₂) in the red region. CIE chromaticity coordinates of the 6LaPO₄–3La₃PO₇–2La₇P₃O₁₈:5%Eu³⁺ phosphor were (0.668, 0.313) in the red region, and defined its potential application as a red phosphor.