Analysis of methanol or formic acid in body fluids by headspace solid-phase microextraction and capillary gas chromatography

Methanol and its metabolite formic acid have been found extractable from human whole blood and urine by headspace solid-phase microextraction (SPME) with a Carboxen/polydimethylsiloxane fiber. The headspace SPME for formic acid was carried out after derivatization to methyl formate under acidic conditions. The determinations of both compounds were made by using acetonitrile as internal standard (IS) and capillary gas chromatography (GC) with flame ionization detection. The headspace SPME–GC gave sharp peaks for methanol, methyl formate and I.S.; and low background noises for whole blood and urine samples. Extraction efficiencies were 0.25–1.05% of methanol and 0.38–0.84% formic acid for whole blood and urine. The calibration curves for methanol and formic acid showed excellent linearity in the range of 1.56 to 800 and 1.56 to 500 μg/0.5 ml of whole blood or urine, respectively. The detection limits were 0.1–0.5 μg/0.5 ml for methanol and 0.6 μg/0.5 ml for formic acid for both body fluids. The within-day relative standard deviations in terms of extraction efficiency for both compounds in whole blood and urine samples were not greater than 9.8%. By using the established SPME method, methanol and formic acid were successfully separated and determined in rat blood after oral administration of methanol.     

Comparison of Soil VOCs measured by soil gas,heated headspace,and methanol extraction techniques

Comparisons of soil volatile organic compound (VOC) measurement techniques and soil properties expected to influence these measurements were performed at two dissimilar sites. A total of 41 soil gas, 52 heated headspace, and 51 methanol extraction/purge‐and‐trap measurements were obtained on collocated samples. Contaminants present at both sites included cis‐1,2‐dichloroethene, 1, 1, 1‐trichloroethane, trichloroethene, and tetrachloroethene. Heated headspace offered the highest sensitivity, as indicated by the greatest percentage of detections per number of analyses. The statistical regression between headspace concentrations and methanol extraction concentrations was highly significant (p < 0.001) with r² = 0.53. Headspace concentrations (range, 7 to 4250 ng/g) ran approximately 20 to 30% of the methanol extraction concentrations (range, 260 to 7300 ng/g), indicating that the methanol was able to extract significantly more of the chlorinated hydrocarbons (CHCs) than the headspace extraction, even in soils with relatively low organic carbon contents (< 0.25%). None of the soil properties (gravimetric moisture content, organic carbon content, percent sand, and percent clay) significantly improved the regression fit. The soil gas responses were unlike either headspace or methanol extraction data. CHC measurements by vapor extraction/soil gas could not be used to predict soil CHC concentrations at these sites.     

Development of a solid phase microextraction-gas chromatography method to determine N-hydroxymethyl-N-methylformamide and N-methylformamide in urine

A headspace solid phase microextraction (SPME) method has been developed to determine metabolites of dimethylformamide, N-hydroxymethyl-N-methylformamide, and N-methylformamide (NMF) as NMF in urine by gas chromatography with nitrogen-phosphorus detector (GC-NPD). An SPME holder with a 65-microm PDMS/DVB fiber coating was used. Optimal desorption conditions were 250 degrees C for 1 min, adsorption at 80 degrees C for 15 min, and 3.00 mL of sample in the headspace vial. The method presented good resolution, repeatability, recovery, detection limit, ruggedness and response linearity.     

Optimization of microwave-assisted transesterification of dry algal biomass using response surface methodology

The effect of microwave irradiation on the simultaneous extraction and transesterification (in situ transesterification) of dry algal biomass to biodiesel was investigated. A high degree of oil/lipid extraction from dry algal biomass and an efficient conversion of the oils/lipids to biodiesel were demonstrated in a set of well-designed experimental runs. A response surface methodology (RSM) was used to analyze the influence of the process variables (dry algae to methanol (wt/vol) ratio, catalyst concentration, and reaction time) on the fatty acid methyl ester conversion. Based on the experimental results and RSM analysis, the optimal conditions for this process were determined as: dry algae to methanol (wt/vol) ratio of around 1:12, catalyst concentration about 2 wt.%, and reaction time of 4 min. The algal biodiesel samples were analyzed with GC-MS and thin layer chromatography (TLC) methods. Transmission electron microscopy (TEM) images of the algal biomass samples before and after the extraction/transesterification reaction are also presented.     

Production of algae-based biodiesel using the continuous catalytic Mcgyan® process

This study demonstrates the production of algal biodiesel from Dunaliella tertiolecta, Nannochloropsis oculata, wild freshwater microalgae, and macroalgae lipids using a highly efficient continuous catalytic process. The heterogeneous catalytic process uses supercritical methanol and porous titania microspheres in a fixed bed reactor to catalyze the simultaneous transesterification and esterification of triacylglycerides and free fatty acids, respectively, to fatty acid methyl esters (biodiesel). Triacylglycerides and free fatty acids were converted to alkyl esters with up to 85% efficiency as measured by 300 MHz ¹H NMR spectroscopy. The lipid composition of the different algae was studied gravimetrically and by gas chromatography. The analysis showed that even though total lipids comprised upwards of 19% of algal dry weight the saponifiable lipids, and resulting biodiesel, comprised only 1% of dry weight. Thus highlighting the need to determine the triacylglyceride and free fatty acid content when considering microalgae for biodiesel production.     

气相色谱法测定啤酒中的游离脂肪酸

气相色谱法测定啤酒中辛酸到二十二碳酸共１１种游离脂肪酸,采用多级溶剂萃取及薄层色谱纯化技术进行样品制备,并采充氮措施抑制脂肪酸的氧化产生,此方法有较好的重复性和回收率。     

Sonication-assisted production of biodiesel using soybean oil and supercritical methanol

High temperature and pressure are generally required to produce biodiesel using supercritical methanol. We reduced the harsh reaction conditions by means of sonicating the reaction mixture prior to transesterification using supercritical methanol. Soybean oil was selected as the raw material for transesterification. As soybean oil contains more unsaturated fatty acid triglycerides, the biodiesel degraded more at high temperature. The reactants were sonicated for 60 min at 35 °C prior to transesterification to avoid degradation of the product and to enhance biodiesel yield at temperatures <300 °C. The process parameters were optimized using central composite design. The variables selected for optimization were temperature, time, and the oil to methanol molar ratio. The temperature and oil to methanol molar ratios were varied from 250 to 280 °C and 1:40–1:50, respectively. The reaction time was tested between 4 and 12 min. The biodiesel was analyzed for any possible degradation by gas chromatography–mass spectroscopy and for the wt% of fatty acid methyl esters (FAME) obtained. The maximum FAME yield (84.2 wt%) was obtained at a temperature of 265.7 °C, an oil to alcohol molar ratio of 1:44.7, and a time of 8.8 min. The optimum yield was obtained at a pressure of 1,500 psi. The pressure and optimum temperature used to obtain the maximum yield were the lowest reported so far without the use of a co-solvent. Thus, the severity of the supercritical reactions was reduced by adding sonication prior to the reaction.     

Sensory Characteristics and Antioxidant Activity of Zanthoxylum bungeanum Maxim. Pericarps

Zanthoxylum bungeanum extracts were prepared using seven solvents: water, methanol, ethanol, acetic acid, ethyl acetate, chloroform, and benzene. The volatile composition in the extracts was qualitatively analyzed using headspace solid‐phase microextraction coupled with gas chromatography mass spectrometry detection, and the alkylamide composition was determined using high‐performance liquid chromatography. The extract compositions differed with respect to the solvents. A total of 49 volatile components belonging to four groups, terpenoids, alcohols, esters, and ketones, were identified in the extracts. The Z. bungeanum extracts were either ester or terpenoid type, dominated by linalyl acetate. The extracts were divided into three distinct groups based on principal component analysis and hierarchical clustering analysis. Water, methanol, and ethanol extracts could be applied in the food and pharmaceutical industries.     

Kinetics of lipase recovery from the aqueous phase of biodiesel production by macroporous resin adsorption and reuse of the adsorbed lipase for biodiesel preparation

A commercial macroporous resin (D3520) was screened for lipase recovery by adsorption from the aqueous phase of biodiesel production. The influences of several factors on the adsorption kinetics were investigated. It was found that the kinetic behavior of lipase adsorption by macroporous resin could be well described by pseudo-first-order model. Temperature had no significant effects on lipase adsorption, while resin-to-protein ratio (R) significantly affected both rate constant (k₁) and equilibrium adsorption capacity (Q_e). No lipase was adsorbed when mixing (shaking) was not performed; however, protein recovery reached 98% after the adsorption was conducted at 200 rpm for 5 h in a shaker. The presence of methanol and glycerol showed significant negative influence on lipase adsorption kinetics. Particularly, increasing glycerol concentration could dramatically decrease k₁ but not impact Q_e. Biodiesel was found to dramatically decrease Q_e even present at a concentration as low as 0.02%, while k₁ was found to increase with biodiesel concentration. The adsorbed lipase showed a relatively stable catalytic activity in tert-butanol system, but poor stability in solvent-free system when used for biodiesel preparation. Oil and biodiesel were also found to adsorb onto resin during transesterification in solvent-free system. Therefore, the resin had to be washed by anhydrous methanol before re-used for lipase recovery.     

Headspace gas chromatography with capillary column for urine alcohol determination

A headspace gas chromatographic method using a fused-silica capillary column Poraplot Q has been developed and validated for the detection and quantification of ethanol in urine. Under optimized conditions, ethanol was properly separated from acetaldehyde, acetone, isopropanol, methanol and n-propanol. Limits of detection (LODs) and quantification (LOQs) were 0.008 and 0.010 g/l, respectively. The precision studies within-run and between-run, using spiked urine samples (0.08, 0.8 and 2.0 g/l) showed maximum coefficients of variation 5.9 and 6.5%, respectively. Results of ethanol recovery varied from 91.6±0.8 to 103.3±1.8% over the concentration range from 0.01 to 3.20 g/l. The method was appropriate for the detection of ethanol in urine samples. This matrix can be used for monitoring alcohol abuse in the workplace and used in alcohol rehabilitation programs.     

Enzymatic production of biodiesel from cotton seed oil using t-butanol as a solvent

The enzymatic production of biodiesel by methanolysis of cottonseed oil was studied using immobilized Candida antarctica lipase as catalyst in t-butanol solvent. Methyl ester production and triacylglycerol disappearance were followed by HPLC chromatography. It was found, using a batch system, that enzyme inhibition caused by undissolved methanol was eliminated by adding t-butanol to the reaction medium, which also gave a noticeable increase of reaction rate and ester yield. The effect of t-butanol, methanol concentration and temperature on this system was determined. A methanolysis yield of 97% was observed after 24h at 50 degrees C with a reaction mixture containing 32.5% t-butanol, 13.5% methanol, 54% oil and 0.017 g enzyme (g oil)(-1). With the same mixture, a 95% ester yield was obtained using a one step fixed bed continuous reactor with a flow rate of 9.6 mlh(-1) (g enzyme)(-1). Experiments with the continuous reactor over 500 h did not show any appreciable decrease in ester yields.     

On-line fermenter headspace gas analysis of methanol and ethanol by capillary inlet mass spectrometry

Summary A new capillary inlet system was used with a magnetic sector mass spectrometer to analyse headspace gas from air-sparged aqueous solutions of methanol and ethanol. The system responded to pulse additions within 2 minutes and gave 90% of equilibrium response after 10 minutes. No memory effects or hysteresis were observed. Signal to concentration ratio was linear with alcohol concentrations up to 5 g/L. Liquid ethanol concentration in aerobic yeast fermentation was followed successfully by on-line headspace gas analysis.     

Rapid and sensitive static headspace gas chromatography-mass spectrometry method for the analysis of ethanol and abused inhalants in blood

A sensitive and specific method using static headspace gas chromatography coupled with mass spectrometry (GC/MS) has been developed for the quantitative determination of ethanol in biological fluids using n-propanol as internal standard. Gas chromatography was performed in isothermal mode with a GC run time of 2.6 min. The quantification was performed using scan mode abstracting a quantitative ion and a qualifier ion for ethanol and for the internal standard. The method was linear (r(2), 0.999, in the concentration range of 5-200 mg/dl), specific (no interference from methanol acetaldehyde, acetone or from endogenous materials), sensitive (limit of quantification and limit of detection of 0.2 and 0.02 mg/dl, respectively) and robust (less than 5% inter- and intra-assay coefficient of variation). A slightly modified method was also developed for the quantification of five commonly abused inhalants (dichloromethane, ethyl acetate, benzene, toluene and xylene) in blood. The method used a gradient GC program with a run time of 8 min. The quantification was performed using scan mode and integrating the area under the peak using trichloroethane as an internal standard. Without optimization, the method was linear (from 5 to 100 mg/l) and sensitive.     

Determination of acrolein by headspace solid-phase microextraction gas chromatography and mass spectrometry

We developed a headspace solid-phase microextraction (headspace SPME) method to measure acrolein in human urine. This new technique resolves some problems with the headspace gas chromatography and mass spectrometry (GC–MS) method which we developed previously. With the original method, a column and a filament were damaged by the injection of air. A 0.5-ml urine (or phosphate-buffered saline) sample in a glass vial containing propionaldehyde as an internal standard was heated for 5 min. The SPME fiber (65 μm carbonwax–divinylbenzene fiber) was exposed to the headspace and then inserted into a GC–MS instrument in which a DB-WAX capillary column (30 m×0.32 mm, film thickness 0.5 μm) was installed. The total analysis time was 15 min. The inter-assay and intra-assay coefficients of variation were 10.07 and 5.79%, respectively. The calibration curve demonstrated good linearity throughout concentrations ranging from 1 to 10 000 nM. The headspace SPME method exhibits high sensitivity and requires a short analysis time as well as the previous method. We conclude that this method is useful to measure urinary acrolein.     

Direct preparation of biodiesel from rapeseed oil leached by two-phase solvent extraction

A new method which coupled the two-phase solvent extraction (TSE) with the synthesis of biodiesel was studied. Investigations were carried out on transesterification of methanol with oil-hexane solution coming from TSE process in the presence of sodium hydroxide as the catalyst. Biodiesel (fatty acid methyl esters) were the products of transesterification. The influential factors of transesterification, such as reaction time, catalyst concentration, mole ratio of methanol to oil and reaction temperature were optimized. The results showed that the optimal reaction parameters were sodium hydroxide concentration 1.1% by weight of rapeseed oil, mole ratio of methanol to oil 9:1, reaction time 120 min, and reaction temperature 55-60 degrees C. Under these conditions, the TG conversion would rise up to 98.2%. Based on the new method, biodiesel production process could be simplified and the biodiesel cost could be reduced.     

Immobilization of steapsin lipase on macroporous immobead-350 for biodiesel production in solvent free system

Commercially available steapsin lipase was immobilized on macroporous polymer beads (IB-350) and further investigated for biodiesel production under solvent free conditions. The fatty acid methyl ester (biodiesel) synthesis was carried out by the methanolysis of fresh and used cooking sunflower oil. The enzymatic reaction for biodiesel synthesis was optimized with various reaction parameters and the obtained reaction conditions were 1: 6 molar ratio (oil: methanol), 50 mg biocatalyst and 20% water content at 45°C for 48 h under solvent free conditions. It was observed that 94% of biodiesel was produced under the optimized reaction conditions. The four step addition of methanol at the interval of 12 h was found to be more effective. Moreover the biocatalyst was effectively reused for four consecutive recycles and was appreciably stable for 90 days. The results obtained highlight potential of immobilized steapsin lipase for biodiesel production.     

SPE-HPLC法快速检测发酵液中紫杉醇的含量

针对红豆杉内生真菌发酵液中紫杉醇的含量测定进行探讨,以建立快速高效低耗的检测方法.采用C_(18)固相萃取柱对紫杉醇进行吸附,用不同浓度的甲醇-乙酸铵和甲醇分别作为洗脱剂对其进行洗脱,比较两者的洗脱效果,洗脱液用HPLC进行检测;色谱条件为:流动相甲醇(v):水(v):乙腈(v)=20: 45: 35,流速:0.70 ml/min,检测波长:227 nm.结果表明,浓度为80%的甲醇溶液洗脱效果较好,紫杉醇的回收率为87.6%.     

Exploration of green integrated approach for effluent treatment through mass culture and biofuel production from unicellular alga,Acutodesmus obliquus RDS01

Abstract

This study deals with the open pond (OP) pilot scale treatment of cassava effluent and enhancement of Ribulose-1,5-bisphosphate carboxylase/oxygenase (RuBisCO) enzyme through CO₂ utilization by the microalga, Acutodesmus obliquus RDS01. The cassava effluent treatment (ET) revealed maximum reduction of ammonia (96.8%), calcium (94.6%), chloride (95.2%), chlorine (98.5%), inorganic phosphate (94.6%), magnesium (96.8%), nitrate (96.89%), organic carbon (95.9%), organic phosphorus (96.3%), potassium (97.9%), sodium (97.1%), and sulfate (95.4%) on 15^th day using A. obliquus. The microalga produced highest RuBisCO enzyme activity (90%), CO₂ utilization efficiency (95%), biomass (8.9 gL^?1), lipid (176.65?mg mL^?1), carbohydrate (96.78?mg mL^?1), biodiesel (4.1?mL g^?1), and bioethanol (3.7?mL g^?1) during OP treatment. The isolated RuBisCO gene (rbcL) was used to construct the protein model by homology modeling. The microalgal-lipid content was analyzed through thin layer chromatography, the biodiesel produced was analyzed using Fourier-transform infrared spectroscopy and gas chromatography mass spectrometry (GCMS). The bioethanol production was confirmed by high performance liquid chromatography and GCMS analyses. A. obliquus produced of 98.75% biodiesel and 96.83% bioethanol in the OP pilot scale treatment A. obliquus. Overall, the microalga A. obliquus could act as an effective CO₂ capturing and bioremediation agent in the cassava ET, and also for the biodiesel and bioethanol can be produced.     

Headspace volatile markers for sensitivity of cocoa (<Emphasis Type="Italic">Theobroma cacao</Emphasis> L.) somatic embryos to cryopreservation

The mechanisms that reduce the viability of plant somatic embryos following cryopreservation are not known. The objective of the present study was to evaluate the sensitivity of cocoa (Theobroma cacao L.) somatic embryos at different stages of an encapsulation–dehydration protocol using stress-related volatile hydrocarbons as markers of injury and recovery. The plant stress hormone ethylene and volatile hydrocarbons derived from hydroxyl radicals (methane) and lipid peroxidation (ethane) were determined using gas chromatography headspace analysis. Ethylene and methane were the only volatiles detected, with both being produced after each step of the cryogenic protocol. Ethylene production was significantly reduced following exposure to liquid nitrogen, but then increased in parallel with embryo recovery. In contrast, the production of methane was cyclic during recovery, with the first cycle occurring earlier for embryos recovered from liquid nitrogen and desiccation than those recovered from earlier steps in the protocol. These results suggest that loss of somatic embryo viability during cryopreservation may be related to the oxidative status of the tissue, and its capacity to produce ethylene. This study has demonstrated that headspace volatile analysis provides a robust non-destructive analytical approach for assessing the survival and recovery of plant somatic embryos following cryopreservation.     

Biodiesel production by supercritical process with crude bio-methanol prepared by wood gasification

In order to prepare a genuine biodiesel, it is essential to use methanol prepared from biomass but not natural gas for biodiesel production. Thus, we have proposed to use crude bio-methanol produced by wood gasification for biodiesel production. Since such a bio-methanol contains some impurities, an effect of its impurities was studied on the biodiesel production by supercritical method. In general, impurities in crude bio-methanol are reported to include methyl formate, ethanol, 1-butanol, diisopropyl ether, water, etc. Triglycerides and oleic acids were, thus, treated with these impurities under supercritical conditions. As a result, it was found that methyl formate, ethanol and 1-butanol could convert them to fatty acid alkyl esters (BDF), whereas no conversion was achieved with diisopropyl ether. Thus, crude bio-methanol can be used for BDF production as a substitute for methanol from fossil resources. However, due to more efficient reaction, crude bio-methanol can be more applicable to the two-step supercritical methanol process, consisting of hydrolysis of triglycerides and subsequent esterification of fatty acids, compared with the one-step supercritical methanol process, where transesterification of triglycerides is a major reaction.