Centrale de mesure ambulatoire biomédicale sur PSoC

Improvement in quality and efficiency of health and medicine, at home and in hospital, has become of paramount importance. The solution to this problem would require the continuous monitoring of several key patient parameters, including the assessment of autonomic nervous system (ANS) activity using non-invasive sensors, providing information for emotional, sensorial, cognitive and physiological analysis of the patient. Recent advances in embedded systems, microelectronics, sensors and wireless networking enable the design of wearable systems capable of such advanced health monitoring. The subject of this article is an ambulatory system comprising of a small wrist device connected to several sensors for the detection of the autonomic nervous system activity. It affords monitoring of skin resistance, skin temperature and heart activity. It is also capable of recording the data on a removable media or sending it to computer via a wireless communication. The wrist device is based on a programmable system-on-chip (PSoC) from Cypress.     

The design of a biochip: a self-assembling molecular-scale memory device

A design for a biochip memory device based on known materials and existing principles is presented. The fabrication of this memory system relies on the self-assembly of the nucleic acid junction system, which acts as the scaffolding for a molecular wire consisting of polyacetylene-like units. A molecular switch to control current is described which is based on the formation of a charge-transfer complex. A molecular-scale bit is presented which is based on oxidation-reduction potentials of metal atoms or clusters. The readable 'bit' which can be made of these components has a volume of 3 x 10(7) A3, and should operate at electronic speeds over short distances.     

Design methodology accounting for the effects of porous medium heterogeneity on hydraulic residence time and biodegradation in horizontal subsurface flow constructed wetlands

Horizontal flow constructed wetlands are engineered systems capable of eliminating a wide range of pollutants from the aquatic environment. Nevertheless, poor hydrodynamic behavior is commonly found resulting in preferential pathways and variations in both (i) the hydraulic residence time distribution (HRTD) and, consequently, (ii) the wetland's treatment efficiency. The aim of this work was to outline a methodology for wetland design that accounts for the effect of heterogeneous hydraulic properties of the porous substrate on the HRTD and treatment efficiency. Biodegradation of benzene was used to illustrate the influence of hydraulic conductivity heterogeneity on wetland efficiency. Random, spatially correlated hydraulic conductivity fields following a log-normal distribution were generated and then introduced in a subsurface flow numerical model. The results showed that the variance of the distribution and the correlation length in the longitudinal direction are key indicators of the extent of heterogeneity. A reduction of the mean hydraulic residence time was observed as the extent of heterogeneity increased, while the HRTD became broader with increased skewness. At the same time, substrate heterogeneity induced preferential flow paths within the wetland bed resulting in variations of the benzene treatment efficiency. Further to this it was observed that the distribution of biomass within the porous bed became heterogeneous, rising questions on the representativeness of sampling. It was concluded that traditional methods for wetland design based on assumptions such as a homogeneous porous medium and plug flow are not reliable. The alternative design methodology presented here is based on the incorporation of heterogeneity directly during the design phase. The same methodology can also be used to optimize existing systems, where the HRTD has been characterized with tracer experiments.     

Design and fabrication development of a micro flow heated channel with measurements of the inside micro-scale flow and heat transfer process

The current work provides a design and fabrication technique for a micro channel system that can provide a uniform heat flux boundary condition on the channel wall and a well insulation on the wall to prevent heat loss from the channel to the outside ambient. Therefore, detailed micro-scale flow and heat transfer process and information along the channel can be studied. Semiconductor sensor material was selected to fabricate both the heaters and the arrays of temperature sensors on a silicon substrate. These heaters and sensors were then moved to a low thermal conductivity epoxy-glass substrate for fabrication of the channel. Design consideration and fabrication techniques involved in this processes will be discussed. A final measurement for the validation of the heaters and the sensors fabricated and a study of the flow friction behavior and the heat transfer coefficient distributions inside the micro channel will be presented. The local Nusselt number distrubution inside the micro channel is reported the first time in the open literature.     

Theory and design of disposable clinical blood viscometer

A disposable clinical whole blood viscometer which can produce viscosity measures over a wide range of shear rates in a single rapid determination has been developed and is currently under test. The design is based upon the time varying flow of blood through a capillary. The flow is driven by the pressure in a fixed volume air chamber and transmitted to the sample through a compliant membrane. The time varying pressure in the air chamber is measured by a suitable transducer. The instantaneous shear stress of the blood in the capillary is proportional to the air pressure, while the instantaneous shear rate is proportional to the pressure-time derivative. Proper design ensures that the system operates as a first order dynamic system with flow resistance entirely determined by the nonlinear sample viscosity. By constructing the air chamber in two parts coupled by a quick disconnect fitting the design can allow for the blood-containing part of the instrument to be discarded, eliminating handling and cleaning of blood contacted components. The entire determination is completed in less than a minute, so that anticoagulants are not necessary. Tests on a prototype show that the instrument gives results in excellent agreement with those obtained on a cone-plate rheogoniometer.