Application of an airlift bioreactor to the nystatin biosynthesis

Pilot plant studies were performed using a concentric-tube airlift bioreactor of 2.5 m³ fermentation volume. The results have proven the relative merits of such a system in the biosynthesis of nystatin, produced by Streptomyces noursei, in submerged aerobic cultivation and batch operation mode. The results were compared to those obtained in a pilot-scale stirred tank bioreactor of 3.5 m³ fermentation volume. The fermentation processes in the two fermentation devices were similar with respect to substrate utilization, biomass production and nystatin biosynthesis. In the riser section, the dissolved oxygen concentration was higher than that in the downcomer. The volumetric oxygen mass transfer coefficient was dependent on the rheological behaviour of the biosynthesis liquids, which was not constant during the fermentation process. The total energy consumption for nystatin production in the airlift bioreactor was 56% of that in the stirred tank, while the operating costs represented 78% of those in the stirred tank bioreactor.     

Improving arachidonic acid fermentation by Mortierella alpina through multistage temperature and aeration rate control in bioreactor

Effective production of arachidonic acid (ARA) using Mortierella alpina was conducted in a 30-L airlift bioreactor. Varying the aeration rate and temperature significantly influenced cell morphology, cell growth, and ARA production, while the optimal aeration rate and temperature for cell growth and product formation were quite different. As a result, a two-stage aeration rate control strategy was constructed based on monitoring of cell morphology and ARA production under various aeration rate control levels (0.6–1.8 vvm). Using this strategy, ARA yield reached 4.7 g/L, an increase of 38.2% compared with the control (constant aeration rate control at 1.0 vvm). Dynamic temperature-control strategy was implemented based on the fermentation performance at various temperatures (13–28°C), with ARA level in total cellular lipid increased by 37.1% comparing to a constant-temperature control (25°C). On that basis, the combinatorial fermentation strategy of two-stage aeration rate control and dynamic temperature control was applied and ARA production achieved the highest level of 5.8 g/L.     

Production of xylanolytic enzymes by <Emphasis Type="Italic">Aspergillus terricola</Emphasis> in stirred tank and airlift tower loop bioreactors

Fungi producing high xylanase levels have attracted considerable attention because of their potential industrial applications. Batch cultivations of Aspergillus terricola fungus were evaluated in stirred tank and airlift bioreactors, by using wheat bran particles suspended in the cultivation medium as substrate for xylanase and β-xylosidase production. In the stirred tank bioreactor, in physical conditions of 30°C, 300 rpm, and aeration of 1 vvm (1 l min⁻¹), with direct inoculation of fungal spores, 7,475 U l⁻¹ xylanase was obtained after 36 h of operation, remaining constant after 24 h. In the absence of air injection in the stirred tank reactor, limited xylanase production was observed (final concentration 740 U l⁻¹). When the fermentation process was realized in the airlift bioreactor, xylanase production was higher than that observed in the stirred tank bioreactor, being 9,265 U l⁻¹ at 0.07 vvm (0.4 l min⁻¹) and 12,845 U l⁻¹ at 0.17 vvm (1 l min⁻¹) aeration rate.     

Effect of cultivation conditions on spore production from Bacillus amyloliquefaciens B128 and its antagonism to Botrytis elliptica

Aims:  To maximize spore production by Bacillus amyloliquefaciens B128, and its antagonism to the fungal pathogen Botrytis elliptica B061. Methods and Results:  In the 5-l stirred-tank bioreactor (STR), with the 0·5 vvm aeration rate, an agitation rate of 200 rev min⁻¹ significantly enhanced the spore yield compared to the same in 300 rev min⁻¹ cultivations. In a 20-l airlift bioreactor (ALR) the maximal spore production was further increased with a controlled aeration rate of 2·5 vvm operated in a 24-mesh net-draft tube mode, and no pH control cultivation. This spore yield in the 20-l ALR was five- and eightfold higher; in addition the cultivation period was 19 h shorter, compared to that obtained from shaker flask and in the 5-l STR cultivations respectively. Conclusions:  Although culture conditions are still to be optimized, by using an ALR with net-draft tube, a scaling up from shaker flasks and STR to ALR of spore production by the strain B128 is technically feasible. Significance and Impact of the Study:  The spore yields obtained using bioreactors were much higher than those previously reported. The freshly produced spore preparations from the B128 strain significantly antagonized the grey mould pathogen B. elliptica.     

Production of extracellular protease from crude substrates with dregs in an external-loop airlift bioreactor with lower ratio of height to diameter

Bacillus subtilis AS1.398 was cultivated in a 11.5-L total volume external-loop airlift bioreactor with a low height-to-diameter ratio of 2.9 and a riser-to-downcomer diameter ratio of 6.6 for the production of protease from crude substrates with dregs. The influence of aeration rate, liquid volume, and sparger hole diameter on protease production was investigated. An average of 8197 u/mL protease activity was obtained after a total fermentation time of 32 h in the external-loop airlift bioreactor with a liquid volume of 8.5 L, air flow rate of 1.5 vvm, and sparger hole diameter of 1.5 mm. The addition of one stainless steel sieve plate in the riser of the airlift bioreactor increased productivity of protease. After 32 h of fermentation, an average of 8718 u/mL protease activity was achieved in the external-loop airlift bioreactor with one sieve plate and an air flow rate of 1.2 vvm, liquid volume of 8.5 L, and gas sparger hole diameter of 1.5 mm. This was 9.0% higher than the typical averages of about 8000 u/mL protease activity in the mechanically stirred tank bioreactors of the enzyme factory using the same microorganism. It is possible to make a scale-up of the external-loop airlift bioreactor and feasible to operate it for production of protease from crude substrate with dregs.     

Improved oxygen transfer and increased l-lactic acid production by morphology control of Rhizopus oryzae in a static bed bioreactor

Rhizopus oryzae was immobilized on a cotton matrix in a static bed bioreactor. Compared with free cells in a stirred tank bioreactor, immobilized R. oryzae in this bioreactor gave higher lactic acid production but lower ethanol production. The highest lactic acid production rate (2.09 g/L h) with the final concentration of 37.83 g/L from 70 g/L glucose was achieved when operating the bioreactor at 700 rpm and 0.5 vvm air. To better understand the relationship between shear effects (agitation and aeration) and R. oryzae morphology and metabolism, oxygen transfer rate, fermentation kinetics, and lactate dehydrogenase activity were determined. In immobilized cell culture, higher oxygen transfer rate and lactic acid production were achieved but lower lactate dehydrogenase activity was found as compared with those in free cell culture operated at the same conditions. These results clearly imply that mass transport was the rate controlling step in lactic acid fermentation by R. oryzae.     

alpha-Amylase production by Bacillus subtilis with dregs in an external-loop airlift bioreactor

An external-loop airlift bioreactor, with a low ratio 2.9 of height-to-diameter of the riser and a ratio 6.6 of riser-to-downcomer diameter, was used to produce alpha-amylase from fermentation with dregs by Bacillus subtilis. The effects of gas flow rate and liquid volume on alpha-amylase production were investigated. After a 36-h fermentation time, an average of 432.3U/ml alpha-amylase activity was obtained under the conditions of liquid volume 8.5l and gas flow rate 1.2vvm for the first 12h of fermentation, 1.4vvm from 12 to 27h, and 1.2vvm from 27h to the end. The activity was higher than that obtained in shaking flasks (409.0U/ml) and in a mechanically stirred tank bioreactor (397.2U/ml) under optimized operating conditions. The fermentation cycle of the airlift bioreactor was shorter than the 48h required for the shaking flasks and close to the 36h of the mechanically stirred tank bioreactor. It was demonstrated that the external-loop airlift bioreactor could substitute for the traditional mechanically stirred tank bioreactor to produce alpha-amylase from fermentation by Bacillus subtilis with dregs.     

Batch and continuous ribonuclease production by immobilized Aspergillus clavatus cells in a bubble-collumn bioreactor

Summary Ribonuclease production using immobilized cells (IC) of Aspergillus clavatus has been studied under batch, repeated-batch and continuous fermentation conditions in a bubble-column bioreactor and compared with production by free cells, Immobilization was achieved by the method of cryostructurization in polyvinyl alcohol beads. The effect of various aeration rates in a column bioreactor has been investigated. Enzyme production by IC [42 000 units (U)·l^–1] during batch fermentations was comparable to that of a free-cell system. The specific productivity of IC was 8.5 times higher than that of free cells. In repeated batch fermentation at various aeration rates, successful reuse of IC was obtained, with comparable levels of enzyme production. Continuous ribonuclease production was achieved for 44 days at 1 vvm aeration and a dilution rate of 0.0 h^–1 with volumetric productivity (450 U·1^–1) and yield.     

High density cultivation of Anchusa officinalis in a stirred-tank bioreactor with in situ filtration

Previously, Su et al. [Biotechnol Bioeng 42: 884–890 (1993)] reported improved production of rosmarinic acid by Anchusa officinalis in shake-flask cultures using a cultivation strategy that involved intermittent medium exchange. Implementation of this cultivation strategy in 2.5-1 stirred-tank bioreactor cultures is investigated in the present study. Intermittent cell/medium separation in the bioreactor was accomplished by means of automated in situ culture filtration. In the bioreactor culture, rosmarinic acid production was found very sensitive to agitation and aeration conditions as well as dissolved oxygen concentration. A maximum cell density of 35 g dry weight/l and a rosmarinic acid concentration of 3.7 g/l were obtained by maintaining the dissolved oxygen concentration above 30% air saturation, gradually raising the impeller tip speed from 34 cm/s to 72 cm/s, and keeping the aeration rate at 0.44 vvm while increasing the O₂: air ratio in the gas feed stream to 4:1. This result is comparable with the data obtained from shake-flask cultures using the same culture strategy.     

Effect of submerged culture conditions on exopolysaccharides production by Armillaria luteo-virens Sacc QH and kinetic modeling

This work aimed to develop the submerged cultivation conditions for improved exopolysaccharides (EPS) production by Armillaria luteo-virens Sacc. The effects of culture temperature, aeration rate, inoculum level, initial pH, and additives on EPS formation and mycelial growth are investigated. The aeration rate, initial pH, and inoculum level significantly affected EPS production under the submerged cultivation. The developed conditions were as follows: cultivation temperature 23 °C, initial pH 5.0, aeration rate 0.5 vvm, 0.5% Tween 80, inoculum level 5% (v/v), and shaking speed 120 r/min. Under the developed conditions, the highest EPS production was 13.01 g/L at 5 days culture time. EPS production was examined in a 5 L bioreactor, and an unstructured kinetic model for EPS formation was well developed. The verified investigations in the large-scale cultivation system showed that the developed models are able to predict the submerged cultivation process of EPS formation. Current results revealed that the submerged cultivation conditions can be utilized to control EPS production, and the unstructured models developed are suitable for explaining EPS production by A. luteo-virens Sacc QH in a large-scale cultivation bioreactor.     

High bioreactor production and emulsifying activity of an unusual exopolymer by Chromohalobacter canadensis 28

Unusual composition of an exopolymer (EP) from an obligate halophilic bacterium Chromohalobacter canadensis 28 has triggered an interest in development of an effective bioreactor process for its production. Its synthesis was investigated in 2‐L bioreactor at agitation speeds at interval 600‐1000 rpm, at a constant air flow rate of 0.5 vvm; aeration rates of 0.5, 1.0, and 1.5 vvm were tested at constant agitation rate of 900 rpm. EP production was affected by both, agitation and aeration. As a result twofold increase of EP yield was observed and additionally increased up to 3.08 mg/mL in a presence of surfactants. For effective scale‐up of bioreactors mass transfer parameters were estimated and lowest values of K_La obtained for the highest productivity fermentation was established. Emulsification activity of EP exceeded that of trade hydrocolloids xanthan, guar gum, and cellulose. A good synergism between EP and commercial cellulose proved its potential exploration as an enhancer of emulsifying properties of trade emulsions. A pronounced lipophilic effect of EP was established toward olive oil and liquid paraffin. Cultivation of human keratinocyte cells (HaCaT) with crude EP and purified γ‐polyglutamic acid (PGA) showed higher viability than control group.     

Coenzyme Q<Subscript>10</Subscript> production by <Emphasis Type="Italic">Rhodobacter sphaeroides</Emphasis> in stirred tank and in airlift bioreactor

A higher Coenzyme Q₁₀ (CoQ₁₀) concentration of 25.04 mg/l was found in airlift bioreactor than the value of 18.11 mg/l obtained in stirred tank under the aerobic-dark cultivation of Rhodobacter sphaeroides. Aeration rate didn’t show obvious impact to CoQ₁₀ production in airlift bioreactor. The fed-batch operation in airlift bioreactor could increase the biomass concentration and led to the maximum CoQ₁₀ concentration of 33.91 mg/l measured, but a lower CoQ₁₀ cell content (3.5 mg CoQ₁₀/DCW) was observed in the fed-batch operation as compared to the batch operation. To enhance the CoQ₁₀ content, an aeration-change strategy was proposed in the fed-batch operation of airlift bioreactor. This strategy led to the maximum CoQ₁₀ concentration of 45.65 mg/l, a 35% increase as compared to the simple fed-batch operation. The results of this study suggested that a fed-batch operation in airlift bioreactor accompanying aeration-change could be suitable for CoQ₁₀ production.     

Pilot-scale culture of somatic embryos of Eleutherococcus senticosus in airlift bioreactors for the production of eleutherosides

Purpose of work

To establish pilot scale bioreactor cultures of somatic embryos of Siberian ginseng for the production of biomass and eleutherosides. Somatic embryos of Eleutherococcus senticosus were cultured in airlift bioreactors using Murashige and Skoog medium with 30 g sucrose l^?1 for the production of biomass and eleutherosides. Various parameters including the type of bioreactor, aeration volume, and inoculum density were optimized for 3 l capacity bioreactors. Balloon-type airlift bioreactors, utilizing a variable aeration volume of 0.1–0.3 vvm and an inoculum of 5 g l^?1, were suitable for biomass and eleutheroside production. In 500 l balloon-type airlift bioreactors, 11.3 g dry biomass l^?1, 220 µg eleutheroside B l^?1, 413 µg eleutheroside E l^?1, and 262 µg eleutheroside E1 l^?1 were produced.     

Development of a stepwise aeration control strategy for efficient docosahexaenoic acid production by Schizochytrium sp.

The effect of aeration on the performance of docosahexaenoic acid (DHA) production by Schizochytrium sp. was investigated in a 1,500-L bioreactor using fed-batch fermentation. Six parameters, including specific growth rate, specific glucose consumption rate, specific lipid accumulation rate, cell yield coefficient, lipid yield coefficient, and DHA yield coefficient, were used to understand the relationship between aeration and the fermentation characteristics. Based on the information obtained from the parameters, a stepwise aeration control strategy was proposed. The aeration rate was controlled at 0.4 volume of air per volume of liquid per minute (vvm) for the first 24 h, then shifted to 0.6 vvm until 96 h, and then switched back to 0.4 vvm until the end of the fermentation. High cell density (71 g/L), high lipid content (35.75 g/L), and high DHA percentage (48.95%) were achieved by using this strategy, and DHA productivity reached 119 mg/L h, which was 11.21% over the best results obtained by constant aeration rate.     

Antioxidant property and production of exopolysaccharide from Armillaria mellea in submerged cultures: Effect of culture aeration rate

Effects of culture aeration rate on production and antioxidant property of exopolysaccharide (EPS) by Armillaria mellea were investigated in a 5‐L stirred‐tank bioreactor where an optimal biomass aeration rate of 1.2 vvm with 0.22 g/g cell yield and 0.6 vvm EPS formation rate with 7.66 mg/g product yield were achieved. A two‐stage aeration process to maximize the biomass and EPS productions proceeded with a 1.55‐fold enhancement (from 4.28 to 6.65 g/L) in biomass formation and a 2.68‐fold enhancement (from 86.9 to 233.2 mg/L) in the EPS production, as compared with those from the aeration rate of 0.3 vvm. The molecular weights of EPS in cultures of different aeration rates are closely correlated with their protein/polysaccharide ratios (R²=0.830) and EC₅₀ (EC₅₀, the effective concentration where the antioxidant property is 50%) values in antioxidant activity (R²=0.960), reducing power (R²=0.894) and chelating ability (R²=0.954). EPS from the two‐stage aeration rate culture shows a strong antioxidant property by the conjugated diene method, reducing power and chelating ability on ions. Therefore, we present results to regulate and to optimize A. mellea cultures to efficiently produce biomass and EPS. The fermented EPS has the potential to be used as for antioxidant‐related functional foods and pharmaceutical industries.     

Effects of Cultivation Parameters on the Morphology of Rhizopus arrhizus and the Lactic Acid Production in a Bubble Column Reactor

The use of filamentous Rhizopus for lactic acid production is facing a challenge due to its low yield mainly caused by the difficulty to control its morphology in submerged fermentation processes. This study was aimed at investigating the impacts of cultivation parameters on the morphology of Rhizopus arrhizus DAR 36017 and lactic acid production using waste potato starch in a laboratory scale bubble column reactor (BCR). The fungal morphology was significantly influenced by carbon sources, process pH, starch concentrations, sparger designs and aeration rates. The favorable morphology for lactic acid production was a freely dispersed small pellet, which was achieved under operation conditions at pH 5.0–6.0, starch concentrations of 60–120 g/L and aeration rates of 0.2–0.8 vvm using a sintered stainless steel disc sparger. Optimal cultivation conditions at pH 6.0 and an aeration rate of 0.4 vvm resulted in the formation of freely dispersed small pellets and 103.8 g/L lactic acid with a yield of 87 % from 120 g/L liquefied potato starch in 48 h. The overall results in terms of lactic acid yield and productivity are comparable to those reported in previous studies using immobilized Rhizopus cells in batch fermentations.     

Processing characteristics of submerged fermentation of Antrodia cinnamomea in airlift bioreactor

Three 5-L airlift bioreactors including airlift reactor with solid draft tube (ALs), airlift reactor with net draft tube (ALn) and bubble column reactor (BC) were investigated for their suitability for cultivating Antrodia cinnamomea, and a stirred tank reactor (ST) was used for comparison. Results indicated that after 7 days fermentation, ALs yielded the highest mycelium content (313 mg/100 mL) and had the lowest dissolved oxygen in the broth. Among different aeration rates (0.025, 0.05, 0.1, 0.5, 1 vvm) used during cultivation of A. cinnamomea in ALs, the aeration rate 0.1 vvm resulted in a volumetric oxygen transfer coefficient of 10.8 h⁻¹ and produced the highest mycelium content. When the optimal conditions were used for the fermentation of A. cinnamomea in an industrial 500-L ALs, the mycelium content in the broth reached 542 mg/100 mL in 28 days. The IC₅₀ values of the ethanol extracts of A. cinnamomea mycelium cultivated in 5-L and 500-L ALs for 28 days were 23 and 17 μg/mL, respectively, for hepatocellular carcinoma cells HepG2. And after 42 days cultivation in 500-L ALs, the IC₅₀ value of the mycelium ethanol extract was reduced to 10 μg/mL.     

Coenzyme Q10 production in a 150-l reactor by a mutant strain of Rhodobacter sphaeroides

For the commercial production of CoQ₁₀, batch-type fermentations were attempted in a 150-l fermenter using a mutant strain of R. sphaeroides. Optimum temperature and initial aeration rate were found to be 30°C and 2 vvm, respectively. Under optimum fermentation conditions, the maximum value of specific CoQ₁₀ content was achieved reproducibly as 6.34 mg/g DCW after 24 h, with 3.02 g/l of DCW. During the fermentation, aeration shift (from the adequate aeration at the early growth phase to the limited aeration in active cellular metabolism) was a key factor in CoQ₁₀ production for scale-up. A higher value of the specific CoQ₁₀ content (8.12 mg/g DCW) was achieved in fed-batch fermentation and comparable to those produced by the pilot-scale fed-batch fermentations of A. tumefaciens, which indicated that the mutant strain of R. sphaeroides used in this study was a potential high CoQ₁₀ producer. This is the first detailed study to demonstrate a pilot-scale production of CoQ₁₀ using a mutant strain of R. sphaeroides.     

Continuous fermentation of soy sauce by immobilized cells of Zygosaccharomyces rouxii in an airlift reactor

Summary The optimum conditions for continuous alcohol fermentation of soy sauce with immobilized Zygosaccharomyces rouxii cells were investigated using an airlift reactor. The optimum pH and temperature of the fermentation were 4.5–5.5 and 25°–27.5° C, respectively. Ethanol content in the fermented liquid was increased with increasing height to diameter ratio of the reactor and the ratio of air to nitrogen in the supplied gas (total supplied gas: 0.08 vvm). A notable decrease in ethanol content was observed when only nitrogen gas was supplied. The products fermented by supplying air (0.02 vvm) had a higher conent of aroma components than that by supplying only nitrogen gas, and the aroma of the former products was similar to that of conventional soy sauce. This alcohol fermentation using an airlift reactor was continued for about 50 days without problems even if conditions such as residence time and aeration were altered.     

Biomass axial distribution in airlift bioreactor with yeast and plant cells

This study was aimed at determining the degree of biomass homogeneity in the various parts of an internal loop airlift bioreactor, thus verifying the assumption, often made in bioreactor studies, of a well-mixed liquid-biomass system. Following characterization of the hydrodynamics of the vessel with water, the axial biomass distribution in the riser and downcomer was determined for plant and yeast cell suspensions of 5.8, 8.5, and 12.5 g DW/L Phaseolus vulgaris and of 30 and 46 g DW/L Saccharomyces cerevisiae. The airlift bioreactor with a surface ratio A(D)/A(D) of 1.04 and aspect ratio of 4.95 was investigated under various aeration rates. The yeast cells were found to be distributed practically uniformly throughout the vessel at the aeration rates of 0.1-1.45 vvm. However, in the case of the denser and cluster-forming plant cells, a clear trend of a gradual bio-mass accumulation in the downcomer, a slightly lower but uniform biomass loading in the riser, and a slightly higher biomass concentration in the gas-liquid separator was observed at the lower aeration rates of 0.1-0.61 vvm. In the case of powderized calcium carbonate (55g/L) often used in fermentations of organic acids, a slight trend of a gradual accumulation of solids towards the bottom parts in both the downcomer and riser was observed. A better representative sampling location, in terms of solids and biomass loading, seems to be in the middle part of the vessel. It is suggested that airlift bioreactors with higher aspect ratios (>5) may be prone to a more significant inhomogeneity of solids (biomass and particles).