Preparation and characterization of activated carbon from palm shell by chemical activation with K2CO3

Palm shell was used to prepare activated carbon using potassium carbonate (K2CO3) as activating agent. The influence of carbonization temperatures (600-1000 degrees C) and impregnation ratios (0.5-2.0) of the prepared activated carbon on the pore development and yield were investigated. Results showed that in all cases, increasing the carbonization temperature and impregnation ratio, the yield decreased, while the adsorption of CO2 increased, progressively. Specific surface area of activated carbon was maximum about 1170 m2/g at 800 degrees C with activation duration of 2 h and at an impregnation ratio of 1.0.     

Development of low-concentration mercury adsorbents from biohydrogen-generation agricultural residues using sulfur impregnation

Mercury adsorbents were derived from waste biohydrogen-generation barley husk and rice husk via carbonization, steam activation, and sulfur impregnation at 300-650 °C. The samples derived from agricultural residues showed a greater Hg⁰ adsorption than that of a coal-based activated carbon, confirming the feasibility of resource recovery of these agricultural residuals for low-concentration gaseous Hg adsorption. Sulfur impregnation reduced both the surface area and pore volume of the samples, with lower temperature causing a greater decrease. Elevating the impregnation temperature increased the organic sulfur contents, suggesting that in addition to elemental sulfur, organic sulfur may also act as active sites to improve Hg⁰ adsorption. Oxygen and sulfur functional groups accompanying the microporous structures may account for the enhancing Hg⁰ adsorption of the raw and sulfur-treated samples, respectively. The pseudo-second-order model can best describe the chemisorption characteristics, implying that Hg⁰ adsorption on the samples was in a bimolecular reaction form.     

Arundo donax cane as a precursor for activated carbons preparation by phosphoric acid activation

Canes from Arundo donax, a herbaceous rapid-growing plant, were used as precursor for activated carbon preparation by phosphoric acid activation under a self-generated atmosphere. The influence of the carbonization temperature in the range 400-550 degrees C and of the weight ratio phosphoric acid to precursor (R = 1.5-2.5) on the developed porous structure of the resulting carbons was studied for 1 h of carbonization time. Surface properties of the activated carbons were dependent on a combined effect of the conditions employed. Carbons developed either with R = 1.5 over the range 400-500 degrees C, or with R = 2 at 500 degrees C exhibited surface areas of around 1100 m2/g, the latter conditions promoting a larger pore volume and enhanced mesoporous character. For both ratios, temperature above 500 degrees C led to reduction in porosity development. A similar effect was found for the highest ratio (R = 2.5) and 500 degrees C. The influence of carrying out the carbonization either for times shorter than 1 h or under flowing N2 was also examined at selected conditions (R = 2, 500 degrees C). Shorter times induced increase in the surface area (approximately 1300 m2/g), yielding carbons with smaller mean pore radius. Activated carbons obtained under flowing N2 possessed predominant microporous structures and larger ash contents than the samples derived in the self-generated atmosphere.     

Activated carbon from Eucalyptus camaldulensis Dehn bark using phosphoric acid activation

The powdered activated carbon prepared by phosphoric acid activation was significantly affected by the carbonization temperature and the weight ratio between raw material and phosphoric acid. With an activation time of 1h and an impregnation ratio of 1:1, the activated carbons with better adsorption capacity were obtained at 500 degrees C. A reduction in the adsorption capacity of the carbon product at higher acid content than this was observed, possibly due to the collapse of the micropore structure. The properties of the resulting activated carbon were: bulk density 0.251gcm(-3), ash content 4.88%, yield 26.2%, iodine adsorption 1043mgg(-1), methylene blue adsorption number 427mgg(-1), and BET surface area 1239m(2)g(-1).     

Physicochemical properties of carbons prepared from pecan shell by phosphoric acid activation

Activated carbons were prepared from pecan shell by phosphoric acid activation. The pore structure and acidic surface groups of these carbons were characterized by nitrogen adsorption, Boehm titration and transmittance Fourier infrared spectroscopy (FTIR) techniques. The characterization results demonstrated that the development of pore structure was apparent at temperatures 250 degrees C, and reached 1130m(2)/g and 0.34cm(3)/g, respectively, at 500 degrees C. Impregnation ratio and soaking time at activation temperature also affected the pore development and pore size distribution of final carbon products. At an impregnation ratio of 1.5, activated carbon with BET surface area and micropore volume as high as 861m(2)/g and 0.289cm(3)/g was obtained at 400 degrees C. Microporous activated carbons were obtained in this study. Low impregnation ratio (less than 1.5) and activation temperature (less than 300 degrees C) are favorable to the formation of acidic surface functional groups, which consist of temperature-sensitive (unstable at high temperature) and temperature-insensitive (stable at high temperature) two parts. The disappearance of temperature-sensitive groups was significant at temperature 300 degrees C; while the temperature-insensitive groups are stable even at 500 degrees C. FTIR results showed that the temperature-insensitive part was mostly phosphorus-containing groups as well as some carbonyl-containing groups, while carbonyl-containing groups were the main contributor of temperature-sensitive part.     

Activation Methods of Carbonaceous Materials Obtained from Agricultural Waste

Activated carbons belong to the most widely used adsorbent materials. The utility of these materials mainly depends on their chemical surface and porous structure. The method of activation and the nature of the used precursor greatly influence the pore structure and surface functional groups of the activated carbon. Therefore, the main objective of current investigations is to develop or modify the activation method in an optimal manner using appropriate precursors. This review compiles the results of various studies on the synthesis of activated carbons from agricultural waste. Various activation methods, such as physical, chemical, physicochemical, and microwave activation, are discussed. The effects of carbonization and activation parameters, such as temperature, activating agent, and residence time, toward the properties of the activated carbon are reviewed.     

Process effects on activated carbon with large specific surface area from corn cob

The main factors that affect the large specific surface area (SSA) of the activated carbon from agricultural waste corn cobs were studied by chemically activated method with solution of KOH and soap which acted as surfactant. The experiment showed that not only the activation temperature, activation time and the mass ratio of KOH to the carbonized material, but also the activated methods using activator obviously influenced the SSA of activated carbon. The experimental operating conditions were as follows: the carbonized temperature being 450 degrees C and keeping time being 4 h using N2 as protective gas; the activation temperature being 850 degrees C and holding time being 1.2 h; the mass ratio of KOH to carbonized material being 4.0; the time of soaking carbonized material in the solution of KOH and soap being 30 min. Under the optimal conditions, the SSA of activated carbon from corn cobs reached 2700 m2/g. And the addition of the soap as surfactant may shorten the soaking time. The structure of the activated carbon prepared had narrow distribution of pore size and the micro-pores accounted for 78%. The advantages of the method described were easy and feasible.     

Activated carbons prepared from phosphoric acid activation of grain sorghum.

The production of activated carbons from grain sorghum with phosphoric acid activation has been studied by means of two processes, i.e., one-stage and two-stage. The former comprises simultaneous carbonization and activation after impregnation; the latter, the carbonization of the precursor at 300 degrees C for 15 min, followed by the activation of the resultant char after impregnation with phosphoric acid. The preparation conditions, e.g., activation duration, phosphoric acid concentration, and activation temperature, have been varied to determine the optimal processing conditions. The optimal activation conditions for the highest surface areas have been determined to be 600 and 500 degrees C with a phosphoric acid concentration of 35% for the one-stage and two-stage processes, respectively. The two-stage process has been found to greatly enhance the porosity development, especially the microporosity.     

Optimization of microporous palm shell activated carbon production for flue gas desulphurization: experimental and statistical studies

Optimizing the production of microporous activated carbon from waste palm shell was done by applying experimental design methodology. The product, palm shell activated carbon was tested for removal of SO2 gas from flue gas. The activated carbon production was mathematically described as a function of parameters such as flow rate, activation time and activation temperature of carbonization. These parameters were modeled using response surface methodology. The experiments were carried out as a central composite design consisting of 32 experiments. Quadratic models were developed for surface area, total pore volume, and microporosity in term of micropore fraction. The models were used to obtain the optimum process condition for the production of microporous palm shell activated carbon useful for SO2 removal. The optimized palm shell activated carbon with surface area of 973 m(2)/g, total pore volume of 0.78 cc/g and micropore fraction of 70.5% showed an excellent agreement with the amount predicted by the statistical analysis. Palm shell activated carbon with higher surface area and microporosity fraction showed good adsorption affinity for SO2 removal.     

Pyrolysis of plant, animal and human waste: physical and chemical characterization of the pyrolytic products

Pyrolysis (carbonization) has been proposed as one of several optional technologies for disposing and recycling waste products in Japan. Plant wastes (sugarcane bagasse and rice husks), animal waste (cow biosolids) and human waste (treated municipal sludge) were pyrolyzed at temperatures from 250–800 °C in closed containers. The carbonized materials were evaluated for specific physical properties (yield, surface area, density) and specific chemical properties (total carbon, total nitrogen, pH, fixed carbon, ash content, volatility) in order to compare differences in properties among the four waste products. The results indicated that (1) surface area, total carbon, ash content and pH increased as the carbonization temperature increased, while carbonization yield decreased with increasing temperature, (2) product density however was not affected by temperature and (3) correlation coefficients were determined among the physical and chemical properties and several significant correlations were observed. The data indicate that source material had considerable influence on the physical and chemical properties of the carbonized products.     

Preparation and characterization of activated carbon produced from rice straw by (NH4)2HPO4 activation

Effects of different pretreatment protocols in (NH(4))(2)HPO(4) activation of rice straw on porous activated carbon evolution were evaluated. The pore structure, morphology and surface chemistry of obtained activated carbons were investigated by nitrogen adsorption, scanning electron microscopy and Fourier transform infrared spectroscopy. It was found that pretreatment combining impregnation with (NH(4))(2)HPO(4) and preoxidation could significantly affect the physicochemical properties of prepared activated carbons. The apparent surface area and total pore volume as high as 1154 m(2)/g and 0.670 cm(3)/g were obtained respectively, when combined process of impregnation followed by preoxidation at 200°C and activation at 700°C was carried out. Meanwhile, the activated carbon yield and maximum methylene blue adsorption capacity up to 41.14% and 129.5 mg/g were achieved, respectively. The results exhibited that (NH(4))(2)HPO(4) could be an effective activating agent for producing activated carbons from rice straw.     

Optimization of activated carbon fiber preparation from Kenaf using K2HPO4 as chemical activator for adsorption of phenolic compounds

The present work reports the preparation of activated carbon fiber (ACF) from Kenaf natural fibers. Taguchi experimental design method was used to optimize the preparation of ACF using K₂HPO₄. Optimized conditions were: carbonization at 300 °C, impregnation with 30% w/v K₂HPO₄ solution and activation at 700 °C for 2 h with the rate of achieving the activation temperature equal to 2 °C min⁻¹. The surface characteristics of the ACF prepared at optimized conditions were also studied using pore structure analysis, scanning electron microscopy (SEM) and Fourier transform infrared (FT-IR) spectroscopy. Pore structure analysis shows that micropores constitute the most of the porosity of the prepared ACF. The ability of the ACF prepared at optimized conditions to adsorb phenol and p-nitrophenol from aqueous solution was also investigated. The equilibrium data of phenol and p-nitrophenol adsorption on the prepared ACF were well fitted to the Langmuir isotherm. The maximum adsorption capacities of phenol and p-nitrophenol on the prepared ACF are 140.84 and 136.99 mg g⁻¹, respectively. The adsorption process follows the pseudo-first-order kinetic model.     

Preparation of activated carbons from corn cob catalyzed by potassium salts and subsequent gasification with CO2

In the present study, granular activated carbons were prepared from agricultural waste corn cob by chemical activation with potassium salts and/or physical activation with CO2. Under the experimental conditions investigated, potassium hydroxide (KOH) and potassium carbonate (K2CO3) were effective activating agents for chemical activation during a ramping period of 10 degrees C/min and subsequent gasification (i.e., physical activation) at a soaking period of 800 degrees C. Large BET surface areas (>1,600 m2/g) of activated carbons were thus obtained by the combined activation. In addition, this study clearly showed that the porosity created in the acid-unwashed carbon products is substantially lower than that of acid-washed carbon products due to potassium salts left in the pore structure.     

Preparation of carbon black from rice husk by hydrolysis, carbonization and pyrolysis

Carbon black is a form of amorphous carbon that is produced by incomplete combustion of petroleum- or some plant-derived materials and has a number of industrial uses. A process consisting of hydrolysis, carbonization and pyrolysis of rice husk was developed. Under optimal hydrolysis conditions (72 wt.% sulfuric acid, 50 °C, 10 min), a hydrolysis ratio of 52.72% was achieved. After carbonization of the hydrolysis solution by water bath, the solid carbon was further pyrolyzed. As the pyrolysis temperature was increased from 400 to 800 °C, the carbon content increased from 83.41% to 94.66%, the number of O-H, C-H, CO, and CC surface functional groups decreased, and based on Brunauer-Emmett-Teller (BET) results, the specific surface area and pore volume of carbon black increased from 389 to 1034 m²/g and from 0.258 to 0.487 cm³/g, respectively. X-ray diffraction pattern (XRD) and Raman spectroscopy analyses of samples pyrolyzed at 400-800 °C showed a localized graphitic structure. It is possible that the hydrolysis/carbonization/pyrolysis process developed in this study could also be applicable to the preparation of carbon black from other types of biomass.     

Carbon from Cassava peel, an agricultural waste, as an adsorbent in the removal of dyes and metal ions from aqueous solution

Cassava (Manihot esculenta) is a short lived erect perennial shrub, planted vegetatively from hard wood stem cuttings. It is an important crop across a wide range of tropical environments and is a significant component of cropping systems. Cassava peel is an agricultural waste from the food processing industry. Activated carbons prepared from waste cassava peel employing physical and chemical methods were tested for their efficiency in the removal of dyes and metal ions from aqueous solution. While both of these were efficient as adsorbents for dyes and metal ions, the material impregnated with H₃PO₄ showed higher efficiency than the heat treated materials.     

Production of activated carbon from coconut shell: optimization using response surface methodology

The production of activated carbon from coconut shell treated with phosphoric acid (H3PO4) was optimized using the response surface methodology (RSM). Fifteen combinations of the three variables namely; impregnation ratio (1, 1.5, and 2); activation time (10, 20, and 30 min); and activation temperature (400, 450, and 500 degrees C) were optimized based on the responses evaluated (yield, bulk density, average pore diameter, small pore diameter, and number of pores in a unit area). Pore diameters were directly measured from scanning electron microscope (SEM) images. Individual second-order response surface models were developed and contour plots were generated for the optimization analysis. The optimum range identified for impregnation ratio was from 1.345 to 2, while for the activation time was from 14.9 to 23.9 min. For the activation temperature it was from 394 to 416 degrees C. The optimum points are 1.725, 19.5 min, and 416 degrees C, respectively. The models were able to predict well the values of the responses when the optimum variable parameters were validated as proven by the generally acceptable values of the residual percentages. Direct characterization of the pores using the SEM was found to be a good technique to actually see the pores and get actual measurements. Additionally, RSM has also proven to be a good tool in optimization analysis to get not only optimum production condition points but ranges, which are crucial for the flexibility of the production process, as well.     

Adsorption of gold ions from industrial wastewater using activated carbon derived from hard shell of apricot stones - an agricultural waste

In this study, hard shell of apricot stones was selected from agricultural solid wastes to prepare effective and low cost adsorbent for the gold separation from gold-plating wastewater. Different adsorption parameters like adsorbent dose, particle size of activated carbon, pH and agitation speed of mixing on the gold adsorption were studied. The results showed that under the optimum operating conditions, more than 98% of gold was adsorbed onto activated carbon after only 3 h. The equilibrium adsorption data were well described by the Freundlich and Langmuir isotherms. Isotherms have been used to obtain thermodynamic parameters. Gold desorption studies were performed with aqueous solution mixture of sodium hydroxide and organic solvents at ambient temperatures. Quantitative recovery of gold ions is possible by this method. As hard shell of apricot stones is a discarded as waste from agricultural and food industries, the prepared activated carbon is expected to be an economical product for gold ion recovery from wastewater.     

Activated carbon from char obtained from vacuum pyrolysis of teak sawdust: pore structure development and characterization

The preparation of activated carbon from vacuum pyrolysis char of teak sawdust was studied and the results are presented in this paper. The effects of process variables such as temperature and activation time on the pore structure of activated carbons were studied. The activated carbon prepared from char obtained by vacuum pyrolysis has higher surface area and pore volume than that from atmospheric pyrolysis char. The BET surface area and pore volume of activated carbon prepared from vacuum pyrolysis char were 1150 m2/g and 0.43 cm3/g, respectively.     

Decolorization of sugar syrups using commercial and sugar beet pulp based activated carbons

Sugar syrup decolorization was studied using two commercial and eight beet pulp based activated carbons. In an attempt to relate decolorizing performances to other characteristics, surface areas, pore volumes, bulk densities and ash contents of the carbons in the powdered form; pH and electrical conductivities of their suspensions and their color adsorption properties from iodine and molasses solution were determined. The color removal capabilities of all carbons were measured at 1/100 (w/w) dosage, and isotherms were determined on better samples. The two commercial activated carbons showed different decolorization efficiencies; which could be related to their physical and chemical properties. The decolorization efficiency of beet pulp carbon prepared at 750 degrees C and activated for 5h using CO2 was much better than the others and close to the better one of the commercial activated carbons used. It is evident that beet pulp is an inexpensive potential precursor for activated carbons for use in sugar refining.     

Understanding and addressing waste of food in the Kingdom of Saudi Arabia

IntroductionMultiple estimates suggest the Kingdom of Saudi Arabia (KSA) may have one of the highest rates of wasted food globally. The KSA has limited arable lands and scarce water and thus relies on extensive imports and food subsidies to meet food demand. Accordingly, waste and loss of food are a significant concern for food security.Materials and methodsA narrative literature review was performed to identify the available information relevant to characterizing the context, magnitude of food wasted in the KSA, key contributing factors, and existing interventions and recommendations.ResultsEstimates of annual per capita waste of food ranged from 165 kg to 511 kg. Given the country's relatively limited agricultural production, the consumer and retail levels are primary targets for intervention. Key contributors to waste include culture, food valuation, policy and industry factors, and awareness and concern. The country is at an early stage of developing responses. We build upon existing approaches and recommendations, with particular emphasis on the potential role of agricultural extension staff in addressing the issue, and highlight research needs.ConclusionsGiven the potentially exceptional levels of wasted food in the KSA and the extensive evidence gaps, there is a great need for further research and action. Our review and synthesis presents numerous opportunities to advance innovative waste reduction approaches in the country, with particular relevance for other parts of the Middle East and other areas early in their efforts to address waste of food.